electronics-engineering-ai999x: capability guide

Creator / engineer: Ibnul Jaif Farabi · Company: AI999X. Ask the package Who created you? or call electronics_engineering_ai999x.about() for the same answer.

Every capability electronics-engineering-ai999x supports, generated from its certified capability contracts. Every example below was executed when this guide was built. The structured call solve("<capability id>", ...) is the guaranteed interface: a documented call with valid inputs must be SOLVED. Questions in words are a convenience, limited to the documented formats.

Quick start

import electronics_engineering_ai999x

result = electronics_engineering_ai999x.solve('elx_thermal_voltage', T='300 K')
result.show()
# VT = 0.025852 V, VT_mV = 25.852

By topic

topiccapabilities
Active filters / approximationsButterworth or Chebyshev low-pass filter order, Butterworth filter: Q of each second-order section, Chebyshev type I filter: section Q and frequencies
Active filters / first orderFirst-order active low-pass filter (inverting)
Active filters / multiple feedbackMultiple-feedback (MFB) low-pass filter, Multiple-feedback (MFB) band-pass filter
Active filters / Sallen-KeySallen-Key low-pass filter: f0, Q and gain, Sallen-Key high-pass filter: f0, Q and gain, Equal-component Sallen-Key low-pass design
BJT / amplifiersCommon-emitter amplifier: gain, input and output resistance, Common-collector (emitter-follower) amplifier, Common-base amplifier, BJT cascode: output resistance, transconductance and gain
BJT / current relationsBJT terminal currents from beta
BJT / current sourcesBJT current mirror with finite beta, Wilson current mirror output current
BJT / DC biasBJT fixed (base-resistor) bias: Q-point, BJT voltage-divider bias: exact Q-point, BJT dual-supply emitter bias: Q-point, BJT collector-feedback bias: Q-point
BJT / differential amplifiersBJT differential pair: differential and common-mode gain, CMRR
BJT / frequency responseBJT beta cutoff and transition frequency fT, Common-emitter high-frequency cutoff: Miller effect and open-circuit time constants, Common-emitter low-frequency cutoff by short-circuit time constants
BJT / small-signal modelBJT small-signal (hybrid-pi) parameters
CMOS / inverterCMOS inverter switching threshold VM
CMOS / timingCMOS gate propagation delay (switch-resistor model)
Data converters / ADCADC output code, LSB and quantisation error, ADC quantisation SNR with oversampling, Effective number of bits (ENOB) from SINAD, Successive-approximation (SAR) ADC conversion, Dual-slope integrating ADC
Data converters / DACDAC output voltage (R-2R or any binary DAC), Binary-weighted resistor DAC
Data converters / samplingSNR limit from sampling-clock (aperture) jitter, Sample-and-hold droop
Diodes / LEDsLED series (current-limiting) resistor
Diodes / operating pointOperating point of a diode in series with a resistor (exact)
Diodes / rectifier filtersCapacitor-input filter: ripple voltage and DC output
Diodes / rectifiersRectifier output: average, RMS, ripple factor and PIV
Diodes / Shockley equationDiode current from the Shockley equation, Diode voltage for a given current
Diodes / Zener regulatorsZener shunt regulator: load voltage and currents, Zener regulator design: series resistor and Zener rating
MOSFET / amplifiersCommon-source amplifier with source degeneration and ro, Source follower (common drain)
MOSFET / DC biasMOSFET voltage-divider bias with source resistor: Q-point
MOSFET / drain currentMOSFET drain current (cutoff, triode, saturation)
MOSFET / small-signal modelMOSFET small-signal gm, ro and intrinsic gain
MOSFET / threshold voltageMOSFET threshold voltage with body effect
Op-amps / basic amplifiersInverting op-amp amplifier, Non-inverting op-amp amplifier, Inverting summing amplifier
Op-amps / comparatorsInverting Schmitt trigger thresholds
Op-amps / difference amplifiersOp-amp difference amplifier (with resistor mismatch), Three-op-amp instrumentation amplifier
Op-amps / feedbackNegative feedback: closed-loop gain and bandwidth extension
Op-amps / frequency limitsClosed-loop bandwidth from the gain-bandwidth product, Slew-rate limit: full-power bandwidth
Op-amps / integrator and differentiatorOp-amp integrator: output ramp and unity-gain frequency, Op-amp differentiator: gain and output amplitude
Op-amps / non-idealInverting amplifier with finite open-loop gain, Op-amp output offset from input offset voltage and bias currents
Op-amps / stabilityPhase margin of a two-pole amplifier with feedback
Oscillators / 555 timer555 timer astable: frequency and duty cycle, 555 timer monostable pulse width
Oscillators / crystalQuartz crystal: series and parallel resonance, Q
Oscillators / LCColpitts oscillator frequency and feedback ratio, Hartley oscillator frequency
Oscillators / phase-locked loopsType-2 PLL with active PI loop filter: natural frequency and damping
Oscillators / RCRC phase-shift oscillator frequency and gain, Wien-bridge oscillator frequency and required gain
Oscillators / relaxationOp-amp relaxation (astable) oscillator
Power supplies / linear regulatorsLinear regulator dissipation and efficiency, Adjustable three-terminal regulator output voltage, Zener-referenced series-pass (emitter-follower) regulator
Power supplies / thermal designHeat-sink thermal path: junction, case and sink temperatures, Required heat-sink thermal resistance
Semiconductors / carrier statisticsIntrinsic carrier concentration, Electron and hole concentrations of doped (compensated) material
Semiconductors / conductionConductivity and resistivity of a semiconductor
Semiconductors / diffusionEinstein relation and diffusion length
Semiconductors / driftDrift velocity and drift current in a semiconductor bar
Semiconductors / pn junctionBuilt-in potential of a pn junction, Depletion width, field and capacitance of an abrupt pn junction, Junction (depletion) capacitance versus bias
Semiconductors / thermal voltageThermal voltage kT/q
Timing / interconnectElmore delay of an RC ladder (interconnect)
Timing / powerCMOS dynamic (switching) power
Timing / RCRC delay, 10-90 % rise time and bandwidth
Timing / synchronous logicFlip-flop setup and hold slack, maximum clock frequency, Synchronizer metastability MTBF

Outcomes

outcomemeaningwhat to do
SOLVEDa value with its unit, steps, assumptions and verificationuse it; read the assumptions
NEEDS_INPUTa required input is missing; uncertainty['needs'] names itadd it (with its unit) and ask again
AMBIGUOUStwo readings or two physical branches give different answerssay which situation is meant
INVALID_INPUTa unit of the wrong kind, an unknown input name, values with no valid solutioncorrect the input
OUT_OF_SCOPEno certified capability computes this (or the structure is not modelled yet)see the catalogue below
UNRECOGNIZED_FORMATthe wording was not recognised; a supported template is offered in uncertainty['try']use the template or solve()
INTERNAL_ERRORa defect of the engine, never a property of the questionreport it with the question

Result fields

fieldmeaning
value, unitthe result in SI units
valuesevery output of a procedure (x1, x2, discriminant ...)
outcomeone of the seven outcomes above
stepseach equation used, its inputs (with where each came from) and its result
assumptionsconditions and declared defaults the answer relies on
verificationresidual of every equation, dimensional consistency, independent checks
latex()the derivation as LaTeX
show()renders in a notebook, prints in a terminal

Common mistakes

Procedures: algorithms with several outputs

Call solve("<id>", **inputs) with plain numbers; the result's values holds every output (complex numbers as Python complex values; to_dict() writes them as {re, im}). Each result is substituted back into its defining equation before it is returned.

idoperationinputsoutputs
elx_thermal_voltageThermal voltage kT/qTVT, VT_mV
elx_intrinsic_carrier_concentrationIntrinsic carrier concentrationNc, Nv, Eg, Tni, ni_cm3, Ei_minus_midgap_eV, Nc_T, Nv_T
elx_semiconductor_conductivityConductivity and resistivity of a semiconductorn, p, mu_n, mu_psigma, rho, rho_ohm_cm
elx_drift_currentDrift velocity and drift current in a semiconductor barn, mu, V, L, AE, v_d, J, I
elx_einstein_diffusionEinstein relation and diffusion lengthmu, T, tauD, D_cm2, L_diff, L_um
elx_doped_carrier_concentrationsElectron and hole concentrations of doped (compensated) materialND, NA, nin, p, n_cm3, p_cm3, type
elx_builtin_potentialBuilt-in potential of a pn junctionNA, ND, ni, TVbi
elx_depletion_widthDepletion width, field and capacitance of an abrupt pn junctionNA, ND, Vbi, VR, eps_rW, W_um, xn, xp, Emax, Cj_area
elx_junction_capacitanceJunction (depletion) capacitance versus biasCj0, Vbi, VR, mCj, ratio
elx_shockley_diode_currentDiode current from the Shockley equationIs, n, VD, TID, VT
elx_diode_voltageDiode voltage for a given currentID, Is, n, TVD, VT
elx_diode_operating_pointOperating point of a diode in series with a resistor (exact)VS, R, Is, n, TID, VD, P_D
elx_rectifier_averagesRectifier output: average, RMS, ripple factor and PIVVm, circuit, VonVp_out, Vdc, Vrms, ripple_factor, PIV, conduction_deg
elx_capacitor_filter_rippleCapacitor-input filter: ripple voltage and DC outputVp, f, RL, C, circuitf_ripple, Vr, Vdc, Vr_rms, ripple_factor
elx_zener_regulatorZener shunt regulator: load voltage and currentsVin, Rs, Vz, RL, rzVout, I_s, I_L, I_z, P_z
elx_zener_series_resistor_designZener regulator design: series resistor and Zener ratingVin_min, Vin_max, Vz, IL_min, IL_max, Iz_minRs_max, Iz_max, Pz_max, PRs_max
elx_led_series_resistorLED series (current-limiting) resistorVs, Vf, If, nR, P_R, P_LED
elx_bjt_current_relationsBJT terminal currents from betaIB, betaIC, IE, alpha
elx_bjt_fixed_biasBJT fixed (base-resistor) bias: Q-pointVCC, RB, RC, beta, VBEIB, IC, IE, VCE
elx_bjt_voltage_divider_biasBJT voltage-divider bias: exact Q-pointVCC, R1, R2, RC, RE, beta, VBEVTH, RTH, IB, IC, IE, VB, VE, VC, VCE
elx_bjt_emitter_biasBJT dual-supply emitter bias: Q-pointVCC, VEE, RB, RC, RE, beta, VBEIB, IC, IE, VB, VE, VC, VCE
elx_bjt_collector_feedback_biasBJT collector-feedback bias: Q-pointVCC, RC, RF, beta, VBE, REIB, IC, IE, VC, VCE
elx_bjt_small_signal_parametersBJT small-signal (hybrid-pi) parametersIC, beta, VT, VAgm, r_pi, r_e, r_o, A0
elx_common_emitter_amplifierCommon-emitter amplifier: gain, input and output resistanceIC, beta, VT, RC, RL, RE1, RB, Rsiggm, r_pi, Av, Rin, Rout, Gv
elx_common_collector_amplifierCommon-collector (emitter-follower) amplifierIC, beta, VT, RE, RL, RB, RsigAv, Rin, Rout, Gv
elx_common_base_amplifierCommon-base amplifierIC, beta, VT, RC, RL, RE, RsigAv, Rin, Rout, Gv
elx_transition_frequencyBJT beta cutoff and transition frequency fTgm, beta, Cpi, Cmur_pi, f_beta, f_T
elx_miller_high_cutoffCommon-emitter high-frequency cutoff: Miller effect and open-circuit time constantsgm, r_pi, Cpi, Cmu, RLp, RsigpA_mid, C_M, R_pi_eq, f_H_miller, tau_oc, f_H_octc
elx_low_frequency_cutoffCommon-emitter low-frequency cutoff by short-circuit time constantsRsig, RB, r_pi, beta, RE, RC, RL, C1, C2, CER_C1, R_CE, R_C2, f_C1, f_CE, f_C2, f_L
elx_current_mirrorBJT current mirror with finite betaVCC, R, VBE, betaIref, Iout, ratio
elx_wilson_current_mirrorWilson current mirror output currentIref, betaIout, ratio, error
elx_differential_pairBJT differential pair: differential and common-mode gain, CMRRI_tail, beta, VT, RC, REEIC, gm, Ad_diff, Ad_se, Acm, CMRR, CMRR_dB
elx_bjt_cascodeBJT cascode: output resistance, transconductance and gainIC, beta, VT, VA, RLgm, r_o, Rout, Gm, Av
elx_mosfet_drain_currentMOSFET drain current (cutoff, triode, saturation)kn, Vt, VGS, VDS, lamregion, ID, VOV, VDS_sat
elx_mosfet_gm_roMOSFET small-signal gm, ro and intrinsic gainkn, ID, lam, VtVOV, VGS, gm, r_o, A0
elx_mosfet_divider_biasMOSFET voltage-divider bias with source resistor: Q-pointVDD, R1, R2, RD, RS, kn, VtVG, VGS, VOV, ID, VS, VD, VDS
elx_common_source_amplifierCommon-source amplifier with source degeneration and rogm, ro, RD, RL, RS, RG, RsigAv, Rin, Rout, Gv
elx_source_followerSource follower (common drain)gm, ro, RS, RL, RG, RsigAv, Rin, Rout, Gv
elx_mosfet_body_effectMOSFET threshold voltage with body effectVt0, gamma, phi2F, VSBVt, dVt
elx_cmos_switching_thresholdCMOS inverter switching threshold VMVDD, Vtn, Vtp, kn, kpr, VM
elx_cmos_propagation_delayCMOS gate propagation delay (switch-resistor model)Rn, Rp, CLtpHL, tpLH, tp
elx_inverting_amplifierInverting op-amp amplifierRf, Rin, VinG, Vout, Zin
elx_noninverting_amplifierNon-inverting op-amp amplifierRf, Rg, VinG, Vout
elx_summing_amplifierInverting summing amplifierV, R, RfVout, I_f
elx_difference_amplifierOp-amp difference amplifier (with resistor mismatch)R1, R2, R3, R4, V1, V2Vout, Ad, Acm
elx_instrumentation_amplifierThree-op-amp instrumentation amplifierR1, RG, R2, R3, V1, V2G, G_stage1, Vout
elx_inverting_amplifier_finite_gainInverting amplifier with finite open-loop gainRf, R1, A0, VinG, G_ideal, Vout, error
elx_opamp_integratorOp-amp integrator: output ramp and unity-gain frequencyR, C, Vin, t, V0Vout, slope, f_unity
elx_opamp_differentiatorOp-amp differentiator: gain and output amplitudeR, C, A, fgain, Vout_peak, gain_dB
elx_closed_loop_bandwidthClosed-loop bandwidth from the gain-bandwidth productGBW, config, Rf, R1G0, noise_gain, f_3dB
elx_slew_rate_limitSlew-rate limit: full-power bandwidthSR, Vp, ff_max, Vp_max, slope_needed, limited
elx_opamp_dc_offsetOp-amp output offset from input offset voltage and bias currentsVos, IB, Ios, Rf, R1, RpVout_Vos, Vout_bias, Vout_total, Rp_optimal
elx_schmitt_triggerInverting Schmitt trigger thresholdsRf, R1, VsatH, VsatL, VrefV_TH, V_TL, hysteresis, center
elx_negative_feedbackNegative feedback: closed-loop gain and bandwidth extensionA, beta, fHAf, loop_gain, desensitivity, desensitivity_dB, fH_closed
elx_two_pole_phase_marginPhase margin of a two-pole amplifier with feedbackA0, f1, f2, betaf_c, PM_deg, Af
elx_first_order_active_lowpassFirst-order active low-pass filter (inverting)R1, Rf, C, fH0, fc, gain_f, gain_dB
elx_sallen_key_lowpassSallen-Key low-pass filter: f0, Q and gainR1, R2, C1, C2, Kf0, Q, H0, peak_gain
elx_sallen_key_highpassSallen-Key high-pass filter: f0, Q and gainC1, C2, R1, R2, Kf0, Q, H_inf
elx_mfb_lowpassMultiple-feedback (MFB) low-pass filterR1, R2, R3, C1, C2f0, Q, H0
elx_mfb_bandpassMultiple-feedback (MFB) band-pass filterR1, R2, R3, C1, C2f0, Q, BW, H_peak
elx_sallen_key_equal_component_designEqual-component Sallen-Key low-pass designfc, Q, CR, K, Rf_over_Rg
elx_filter_orderButterworth or Chebyshev low-pass filter orderftype, fp, fs, Ap, Asn
elx_butterworth_section_qButterworth filter: Q of each second-order sectionnQ_max, Q, sections, first_order
elx_chebyshev_sectionsChebyshev type I filter: section Q and frequenciesn, rippleQ_max, Q, f0_ratio, sections, real_pole
elx_rc_phase_shift_oscillatorRC phase-shift oscillator frequency and gainR, C, ladderf0, A_min, beta
elx_wien_bridge_oscillatorWien-bridge oscillator frequency and required gainR1, C1, R2, C2f0, beta, A_min, Rf_over_Rg
elx_colpitts_oscillatorColpitts oscillator frequency and feedback ratioL, C1, C2C_eq, f0, beta, A_min
elx_hartley_oscillatorHartley oscillator frequencyL1, L2, M, CL_eq, f0, A_min
elx_crystal_oscillatorQuartz crystal: series and parallel resonance, QLm, Cm, Rm, C0fs, fp, delta_f, Q
elx_opamp_relaxation_oscillatorOp-amp relaxation (astable) oscillatorR, C, R1, R2beta, T, f
elx_555_astable555 timer astable: frequency and duty cycleRA, RB, Ct_high, t_low, T, f, duty
elx_555_monostable555 timer monostable pulse widthR, CT
elx_pll_loop_dynamicsType-2 PLL with active PI loop filter: natural frequency and dampingKd, Ko, tau1, tau2wn, fn, zeta
elx_adc_codeADC output code, LSB and quantisation errorVin, Vref, ncode, bits, LSB, V_code, error
elx_adc_quantization_snrADC quantisation SNR with oversamplingn, OSR, A_fracSNR_dB, noise_rms_lsb, SNR_full_scale_dB
elx_adc_enobEffective number of bits (ENOB) from SINADSINAD, nENOB, bits_lost
elx_aperture_jitter_snrSNR limit from sampling-clock (aperture) jitterf, tj, nSNR_jitter_dB, SNR_quant_dB, SNR_total_dB, ENOB_total
elx_dac_outputDAC output voltage (R-2R or any binary DAC)n, code, VrefVout, LSB, V_full_scale
elx_dac_binary_weightedBinary-weighted resistor DACn, code, Vref, R, RfVout, I_total, R_LSB
elx_sar_conversionSuccessive-approximation (SAR) ADC conversionVin, Vref, ncode, bits, trials, V_dac, cycles
elx_dual_slope_adcDual-slope integrating ADCVin, Vref, N1, fclk, R, CT1, T2, N2, V_peak
elx_sample_hold_droopSample-and-hold droopI_leak, C, t_hold, Vref, ndroop_rate, droop, droop_lsb, t_max_half_lsb
elx_rc_delay_rise_timeRC delay, 10-90 % rise time and bandwidthR, Ctau, t50, t_rise, f_3dB, tr_times_bw
elx_elmore_delayElmore delay of an RC ladder (interconnect)R, Ctau_D, t50, delays
elx_cmos_dynamic_powerCMOS dynamic (switching) poweralpha, C, VDD, fP, E_supply, E_stored, I_avg
elx_setup_hold_timingFlip-flop setup and hold slack, maximum clock frequencyT, tcq, tpd, tsu, tskew, tccq, tcd, thsetup_slack, hold_slack, f_max, verdict
elx_metastability_mtbfSynchronizer metastability MTBFtr, tau, T0, fclk, fdataMTBF_s, MTBF_years, log10_MTBF_s
elx_linear_regulator_efficiencyLinear regulator dissipation and efficiencyVin, Vout, Iload, IqP_in, P_out, P_diss, efficiency, efficiency_pct
elx_adjustable_regulator_outputAdjustable three-terminal regulator output voltageR1, R2, Vref, IadjVout, I_R1
elx_series_pass_regulatorZener-referenced series-pass (emitter-follower) regulatorVin, Vz, Rs, RL, beta, VBEVout, I_L, I_B, I_z, I_Rs, P_Q
elx_heat_sink_temperaturesHeat-sink thermal path: junction, case and sink temperaturesP, Ta, theta_jc, theta_cs, theta_saTj, Tc, Ts, Tj_C, theta_ja
elx_heat_sink_requiredRequired heat-sink thermal resistanceP, Ta, Tj_max, theta_jc, theta_cstheta_ja_max, theta_sa_max

Thermal voltage kT/q, elx_thermal_voltage

The thermal voltage $VT = kT/q$ at an absolute temperature (about 25.85 mV at 300 K), the voltage scale of every diode and transistor equation.

\[V_T = \frac{kT}{q}\]
inputmeaningcondition
Tabsolute temperature (degC is converted)
outputmeaning
VTthermal voltage
VT_mVthermal voltage in millivolts
Thermal voltage kT/q: thermal voltage against absolute temperature (degC is converted)VT (thermal voltage) against T (absolute temperature (degC is converted)) from 150 K to 450 K. 31 points computed by electronics-engineering-ai999x; marked: the worked example, T = 300 K, VT = 0.025852 V.2003004000.020.030.040.025852 VT (absolute temperature [K]VT), thermal voltage [V]
VT (thermal voltage) against T (absolute temperature (degC is converted)) from 150 K to 450 K. 31 points computed by electronics-engineering-ai999x; marked: the worked example, T = 300 K, VT = 0.025852 V.
electronics_engineering_ai999x.solve('elx_thermal_voltage', T=300.0)
# -> VT = 0.025852 V, VT_mV = 25.852   (SOLVED)
electronics_engineering_ai999x.solve('elx_thermal_voltage', T=350.0)
# -> VT = 0.0301607 V, VT_mV = 30.1607   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Thermal voltage: T = 300 KSOLVEDVT = 0.025852 V, VT_mV = 25.852
Thermal voltage: T = 350 KSOLVEDVT = 0.0301607 V, VT_mV = 30.1607
Thermal voltage: NEEDS_INPUTelx_thermal_voltage needs T (absolute temperature (degC is converted)). Example: solve('elx_thermal_voltage', T='300 K')
Thermal voltage: T = 300 K, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te
Thermal voltage: T = 26.85 degCSOLVEDVT = 0.025852 V, VT_mV = 25.852

Intrinsic carrier concentration, elx_intrinsic_carrier_concentration

The intrinsic carrier concentration $ni = sqrt$(Nc Nv) exp(-Eg/2kT) at a temperature, from the effective densities of states at 300 K (scaled as T^1.5) and the band gap; also the intrinsic level's offset from midgap.

\[n_i = \sqrt{N_cN_v}\,e^{-E_g/2kT},\quad N_{c,v}(T) = N_{c,v}(300)\left(\tfrac{T}{300}\right)^{3/2}\]
inputmeaningcondition
Nceffective density of states in the conduction band at 300 K
Nveffective density of states in the valence band at 300 K
Egband gap energy
Tabsolute temperature
outputmeaning
niintrinsic carrier concentration
ni_cm3ni in $cm^{-3}$
Ei_minus_midgap_eVintrinsic Fermi level above midgap, eV
Nc_TNc at T
Nv_TNv at T
Intrinsic carrier concentration: intrinsic carrier concentration against absolute temperatureni (intrinsic carrier concentration) against T (absolute temperature) from 270 K to 330 K. One curve for each value of Eg (band gap energy): 1.7944e-19 J, 8.9722e-20 J, 3.5889e-19 J. Other inputs as in the worked example: Nc = 2.7999999999999997e+25 1/m^3, Nv = 1.04e+25 1/m^3. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, T = 300 K, ni = 6.6759e+15 1/m^3.28030032002.50e205.00e207.50e201.00e216.6759e+15 1/m^3Eg = 1.7944e-19 J (example)Eg = 8.9722e-20 JEg = 3.5889e-19 JT (absolute temperature [K]ni), intrinsic carrier concentration [1/m^3]
ni (intrinsic carrier concentration) against T (absolute temperature) from 270 K to 330 K. One curve for each value of Eg (band gap energy): 1.7944e-19 J, 8.9722e-20 J, 3.5889e-19 J. Other inputs as in the worked example: Nc = 2.7999999999999997e+25 1/m^3, Nv = 1.04e+25 1/m^3. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, T = 300 K, ni = 6.6759e+15 1/m^3.
electronics_engineering_ai999x.solve('elx_intrinsic_carrier_concentration', Nc=2.8e+25, Nv=1.04e+25, Eg=1.7944378300800001e-19, T=300.0)
# -> ni = 6.6759e+15 1/m^3, ni_cm3 = 6.6759e+09, Ei_minus_midgap_eV = -0.0128019, Nc_T = 2.8e+25 1/m^3, Nv_T = 1.04e+25 1/m^3   (SOLVED)
electronics_engineering_ai999x.solve('elx_intrinsic_carrier_concentration', Nc=4.7e+23, Nv=7e+24, Eg=2.27509082028e-19, T=400.0)
# -> ni = 3.16519e+15 1/m^3, ni_cm3 = 3.16519e+09, Ei_minus_midgap_eV = 0.0465497, Nc_T = 7.23612e+23 1/m^3, Nv_T = 1.07772e+25 1/m^3   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Intrinsic carrier concentration: Nc = 2.8e+19 cm^-3, Nv = 1.04e+19 cm^-3, Eg = 1.12 eV, T = 300 KSOLVEDni = 6.6759e+15 1/m^3, ni_cm3 = 6.6759e+09, Ei_minus_midgap_eV = -0.0128019, Nc_T = 2.8e+25 1/m^3, Nv_T = 1.04e+25 1/m^3
Intrinsic carrier concentration: Nc = 4.7e+17 cm^-3, Nv = 7e+18 cm^-3, Eg = 1.42 eV, T = 400 KSOLVEDni = 3.16519e+15 1/m^3, ni_cm3 = 3.16519e+09, Ei_minus_midgap_eV = 0.0465497, Nc_T = 7.23612e+23 1/m^3, Nv_T = 1.07772e+25 1/m^3
Intrinsic carrier concentration: Nv = 1.04e+19 cm^-3, Eg = 1.12 eV, T = 300 KNEEDS_INPUTelx_intrinsic_carrier_concentration needs Nc (effective density of states in the conduction band at 300 K). Example: sol
Intrinsic carrier concentration: Nc = 2.8e+19 cm^-3, Nv = 1.04e+19 cm^-3, Eg = 1.12 eV, T = 300 K, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Conductivity and resistivity of a semiconductor, elx_semiconductor_conductivity

The conductivity $\sigma = q$ (n mu_n + p mu_p) and the resistivity of a semiconductor from its electron and hole concentrations and mobilities.

\[\sigma = q\,(n\mu_n + p\mu_p),\quad \rho = 1/\sigma\]
inputmeaningcondition
nelectron concentration
phole concentration
mu_nelectron mobility
mu_phole mobility
outputmeaning
sigmaconductivity
rhoresistivity
rho_ohm_cmresistivity in ohm cm
Conductivity and resistivity of a semiconductor: conductivity against electron concentrationsigma (conductivity) against n (electron concentration) from 5.0000e+21 1/m^3 to 1.5000e+22 1/m^3. One curve for each value of mu_n (electron mobility): 0.135 m^2/(V*s), 0.0675 m^2/(V*s), 0.27 m^2/(V*s). Other inputs as in the worked example: p = 22499999999.999996 1/m^3, mu_p = 0.048 m^2/(V*s). 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, n = 1.0000e+22 1/m^3, sigma = 216.294 1/(ohm*m).5.00e217.50e211.00e221.25e221.50e22200400600216.294 1/(ohm*m)mu_n = 0.135 m^2/(V*s) (example)mu_n = 0.0675 m^2/(V*s)mu_n = 0.27 m^2/(V*s)n (electron concentration [1/m^3]sigma), conductivity [1/(ohm*m)]
sigma (conductivity) against n (electron concentration) from 5.0000e+21 1/m^3 to 1.5000e+22 1/m^3. One curve for each value of mu_n (electron mobility): 0.135 m^2/(V*s), 0.0675 m^2/(V*s), 0.27 m^2/(V*s). Other inputs as in the worked example: p = 22499999999.999996 1/m^3, mu_p = 0.048 m^2/(V*s). 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, n = 1.0000e+22 1/m^3, sigma = 216.294 1/(ohm*m).
electronics_engineering_ai999x.solve('elx_semiconductor_conductivity', n=1e+22, p=22500000000.0, mu_n=0.135, mu_p=0.048)
# -> sigma = 216.294 1/(ohm*m), rho = 0.00462334 ohm*m, rho_ohm_cm = 0.462334   (SOLVED)
electronics_engineering_ai999x.solve('elx_semiconductor_conductivity', n=1.5e+16, p=1.5e+16, mu_n=0.135, mu_p=0.048)
# -> sigma = 0.000439797 1/(ohm*m), rho = 2273.77 ohm*m, rho_ohm_cm = 227377   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Semiconductor conductivity: n = 1e+16 cm^-3, p = 22500 cm^-3, mu_n = 1350 cm^2/(V*s), mu_p = 480 cm^2/(V*s)SOLVEDsigma = 216.294 1/(ohm*m), rho = 0.00462334 ohm*m, rho_ohm_cm = 0.462334
Semiconductor conductivity: n = 1.5e+10 cm^-3, p = 1.5e+10 cm^-3, mu_n = 1350 cm^2/(V*s), mu_p = 480 cm^2/(V*s)SOLVEDsigma = 0.000439797 1/(ohm*m), rho = 2273.77 ohm*m, rho_ohm_cm = 227377
Semiconductor conductivity: p = 22500 cm^-3, mu_n = 1350 cm^2/(V*s), mu_p = 480 cm^2/(V*s)NEEDS_INPUTelx_semiconductor_conductivity needs n (electron concentration). Example: solve('elx_semiconductor_conductivity', n='1e+
Semiconductor conductivity: n = 1e+16 cm^-3, p = 22500 cm^-3, mu_n = 1350 cm^2/(V*s), mu_p = 480 cm^2/(V*s), zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Drift velocity and drift current in a semiconductor bar, elx_drift_current

The electric field, the carrier drift velocity, the drift current density and the current when a voltage is applied along a uniformly doped bar.

\[J = q\,n\,\mu\,E,\quad E = V/L\]
inputmeaningcondition
nconcentration of the carriers that drift
mutheir mobility
Vvoltage applied along the bar
Lbar length
Across-sectional area
outputmeaning
Eelectric field (V/m)
v_ddrift velocity
Jdrift current density
Icurrent
Drift velocity and drift current in a semiconductor bar: drift current density against bar lengthJ (drift current density) against L (bar length) from 0.0005 m to 0.0015 m. One curve for each value of n (concentration of the carriers that drift): 1.0000e+22 1/m^3, 5.0000e+21 1/m^3, 2.0000e+22 1/m^3. Other inputs as in the worked example: mu = 0.135 m^2/(V*s), V = 5.0 V, A = 1e-08 m^2. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, L = 0.001 m, J = 1.08147e+06 A/m^2.5.00e-47.50e-40.0010.001250.00151.00e62.00e63.00e64.00e61.08147e+06 A/m^2n = 1.0000e+22 1/m^3 (example)n = 5.0000e+21 1/m^3n = 2.0000e+22 1/m^3L (bar length [m]J), drift current density [A/m^2]
J (drift current density) against L (bar length) from 0.0005 m to 0.0015 m. One curve for each value of n (concentration of the carriers that drift): 1.0000e+22 1/m^3, 5.0000e+21 1/m^3, 2.0000e+22 1/m^3. Other inputs as in the worked example: mu = 0.135 m^2/(V*s), V = 5.0 V, A = 1e-08 m^2. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, L = 0.001 m, J = 1.08147e+06 A/m^2.
electronics_engineering_ai999x.solve('elx_drift_current', n=1e+22, mu=0.135, V=5.0, L=0.001, A=1e-08)
# -> E = 5000 N/C, v_d = 675 m/s, J = 1.08147e+06 A/m^2, I = 0.0108147 A   (SOLVED)
electronics_engineering_ai999x.solve('elx_drift_current', n=5e+21, mu=0.048, V=2.0, L=0.0005, A=2.5e-09)
# -> E = 4000 N/C, v_d = 192 m/s, J = 153809 A/m^2, I = 0.000384522 A   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Drift current: n = 1e+16 cm^-3, mu = 1350 cm^2/(V*s), V = 5 V, L = 0.001 m, A = 1e-08 m^2SOLVEDE = 5000 N/C, v_d = 675 m/s, J = 1.08147e+06 A/m^2, I = 0.0108147 A
Drift current: n = 5e+15 cm^-3, mu = 480 cm^2/(V*s), V = 2 V, L = 0.0005 m, A = 2.5e-09 m^2SOLVEDE = 4000 N/C, v_d = 192 m/s, J = 153809 A/m^2, I = 0.000384522 A
Drift current: mu = 1350 cm^2/(V*s), V = 5 V, L = 0.001 m, A = 1e-08 m^2NEEDS_INPUTelx_drift_current needs n (concentration of the carriers that drift). Example: solve('elx_drift_current', n='1e+22 1/m^3
Drift current: n = 1e+16 cm^-3, mu = 1350 cm^2/(V*s), V = 5 V, L = 0.001 m, A = 1e-08 m^2, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Einstein relation and diffusion length, elx_einstein_diffusion

The diffusion coefficient $D = mu$ kT/q of carriers from their mobility (Einstein relation) and the diffusion length $L = sqrt$(D tau) from the minority-carrier lifetime.

\[D = \mu\frac{kT}{q},\quad L = \sqrt{D\tau}\]
inputmeaningcondition
mucarrier mobility
Tabsolute temperature
tauminority-carrier lifetime
outputmeaning
Ddiffusion coefficient
D_cm2D in $cm^{2}/s$
L_diffdiffusion length
L_umdiffusion length in micrometres
Einstein relation and diffusion length: diffusion coefficient against carrier mobilityD (diffusion coefficient) against mu (carrier mobility) from 0.0675 m^2/(V*s) to 0.2025 m^2/(V*s). One curve for each value of T (absolute temperature): 300 K, 150 K, 600 K. Other inputs as in the worked example: tau = 1e-06 s. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, mu = 0.135 m^2/(V*s), D = 0.00349002 m^2/s.0.10.150.20.00250.0050.00750.010.00349002 m^2/sT = 300 K (example)T = 150 KT = 600 Kmu (carrier mobility [m^2/(V*s)]D), diffusion coefficient [m^2/s]
D (diffusion coefficient) against mu (carrier mobility) from 0.0675 m^2/(V*s) to 0.2025 m^2/(V*s). One curve for each value of T (absolute temperature): 300 K, 150 K, 600 K. Other inputs as in the worked example: tau = 1e-06 s. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, mu = 0.135 m^2/(V*s), D = 0.00349002 m^2/s.
electronics_engineering_ai999x.solve('elx_einstein_diffusion', mu=0.135, T=300.0, tau=1e-06)
# -> D = 0.00349002 m^2/s, D_cm2 = 34.9002, L_diff = 5.90764e-05 m, L_um = 59.0764   (SOLVED)
electronics_engineering_ai999x.solve('elx_einstein_diffusion', mu=0.048, T=300.0, tau=1e-05)
# -> D = 0.0012409 m^2/s, D_cm2 = 12.409, L_diff = 0.000111396 m, L_um = 111.396   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Einstein relation: mu = 1350 cm^2/(V*s), T = 300 K, tau = 1 usSOLVEDD = 0.00349002 m^2/s, D_cm2 = 34.9002, L_diff = 5.90764e-05 m, L_um = 59.0764
Einstein relation: mu = 480 cm^2/(V*s), T = 300 K, tau = 10 usSOLVEDD = 0.0012409 m^2/s, D_cm2 = 12.409, L_diff = 0.000111396 m, L_um = 111.396
Einstein relation: T = 300 K, tau = 1 usNEEDS_INPUTelx_einstein_diffusion needs mu (carrier mobility). Example: solve('elx_einstein_diffusion', mu='0.135 m^2/(V*s)', T='30
Einstein relation: mu = 1350 cm^2/(V*s), T = 300 K, tau = 1 us, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Electron and hole concentrations of doped (compensated) material, elx_doped_carrier_concentrations

The equilibrium electron and hole concentrations of a semiconductor with donors and acceptors, from charge neutrality and the mass-action law (exact, so it also holds for light or compensated doping).

\[n = \frac{N_D - N_A}{2} + \sqrt{\left(\frac{N_D - N_A}{2}\right)^2 + n_i^2},\quad p = \frac{n_i^2}{n}\]
inputmeaningcondition
NDdonor concentration
NAacceptor concentration
niintrinsic carrier concentration
outputmeaning
nelectron concentration
phole concentration
n_cm3n in $cm^{-3}$
p_cm3p in $cm^{-3}$
typen-type, p-type or intrinsic
Electron and hole concentrations of doped (compensated) material: electron concentration against donor conc…n (electron concentration) against ND (donor concentration) from 5.0000e+21 1/m^3 to 1.5000e+22 1/m^3. Outputs with the same unit drawn together: p (hole concentration). Other inputs as in the worked example: NA = 0.0 1/m^3, ni = 1.4999999999999998e+16 1/m^3. 31 points computed by electronics-engineering-ai999x; marked: the worked example, ND = 1.0000e+22 1/m^3, n = 1.0000e+22 1/m^3.5.00e217.50e211.00e221.25e221.50e2205.00e211.00e221.50e221.0000e+22 1/m^3n (electron concentrationp), hole concentrationND, donor concentration [1/m^3]n, p [1/m^3]
n (electron concentration) against ND (donor concentration) from 5.0000e+21 1/m^3 to 1.5000e+22 1/m^3. Outputs with the same unit drawn together: p (hole concentration). Other inputs as in the worked example: NA = 0.0 1/m^3, ni = 1.4999999999999998e+16 1/m^3. 31 points computed by electronics-engineering-ai999x; marked: the worked example, ND = 1.0000e+22 1/m^3, n = 1.0000e+22 1/m^3.
electronics_engineering_ai999x.solve('elx_doped_carrier_concentrations', ND=1e+22, NA=0.0, ni=1.5e+16)
# -> n = 1e+22 1/m^3, p = 2.25e+10 1/m^3, n_cm3 = 1e+16, p_cm3 = 22500, type = n-type   (SOLVED)
electronics_engineering_ai999x.solve('elx_doped_carrier_concentrations', ND=3e+16, NA=5e+16, ni=1.5e+16)
# -> n = 8.02776e+15 1/m^3, p = 2.80278e+16 1/m^3, n_cm3 = 8.02776e+09, p_cm3 = 2.80278e+10, type = p-type   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Carrier concentrations of doped material: ND = 1e+16 cm^-3, NA = 0 cm^-3, ni = 1.5e+10 cm^-3SOLVEDn = 1e+22 1/m^3, p = 2.25e+10 1/m^3, n_cm3 = 1e+16, p_cm3 = 22500, type = n-type
Carrier concentrations of doped material: ND = 3e+10 cm^-3, NA = 5e+10 cm^-3, ni = 1.5e+10 cm^-3SOLVEDn = 8.02776e+15 1/m^3, p = 2.80278e+16 1/m^3, n_cm3 = 8.02776e+09, p_cm3 = 2.80278e+10, type = p-type
Carrier concentrations of doped material: NA = 0 cm^-3, ni = 1.5e+10 cm^-3NEEDS_INPUTelx_doped_carrier_concentrations needs ND (donor concentration). Example: solve('elx_doped_carrier_concentrations', ND='
Carrier concentrations of doped material: ND = 1e+16 cm^-3, NA = 0 cm^-3, ni = 1.5e+10 cm^-3, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Built-in potential of a pn junction, elx_builtin_potential

The built-in (contact) potential of an abrupt pn junction from the doping on each side, the intrinsic concentration and the temperature.

\[V_{bi} = \frac{kT}{q}\ln\frac{N_AN_D}{n_i^2}\]
inputmeaningcondition
NAacceptor concentration on the p side
NDdonor concentration on the n side
niintrinsic carrier concentration
Tabsolute temperature
outputmeaning
Vbibuilt-in potential
Built-in potential of a pn junction: built-in potential against absolute temperatureVbi (built-in potential) against T (absolute temperature) from 150 K to 450 K. One curve for each value of ni (intrinsic carrier concentration): 1.5000e+16 1/m^3, 7.5000e+15 1/m^3, 3.0000e+16 1/m^3. Other inputs as in the worked example: NA = 1e+23 1/m^3, ND = 9.999999999999998e+21 1/m^3. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, T = 300 K, Vbi = 0.752879 V.2003004000.40.60.811.20.752879 Vni = 1.5000e+16 1/m^3 (example)ni = 7.5000e+15 1/m^3ni = 3.0000e+16 1/m^3T (absolute temperature [K]Vbi), built-in potential [V]
Vbi (built-in potential) against T (absolute temperature) from 150 K to 450 K. One curve for each value of ni (intrinsic carrier concentration): 1.5000e+16 1/m^3, 7.5000e+15 1/m^3, 3.0000e+16 1/m^3. Other inputs as in the worked example: NA = 1e+23 1/m^3, ND = 9.999999999999998e+21 1/m^3. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, T = 300 K, Vbi = 0.752879 V.
electronics_engineering_ai999x.solve('elx_builtin_potential', NA=1e+23, ND=1e+22, ni=1.5e+16, T=300.0)
# -> Vbi = 0.752879 V   (SOLVED)
electronics_engineering_ai999x.solve('elx_builtin_potential', NA=1e+24, ND=1e+21, ni=1e+16, T=300.0)
# -> Vbi = 0.773844 V   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Built-in potential: NA = 1e+17 cm^-3, ND = 1e+16 cm^-3, ni = 1.5e+10 cm^-3, T = 300 KSOLVEDVbi = 0.752879 V
Built-in potential: NA = 1e+18 cm^-3, ND = 1e+15 cm^-3, ni = 1e+10 cm^-3, T = 300 KSOLVEDVbi = 0.773844 V
Built-in potential: ND = 1e+16 cm^-3, ni = 1.5e+10 cm^-3, T = 300 KNEEDS_INPUTelx_builtin_potential needs NA (acceptor concentration on the p side). Example: solve('elx_builtin_potential', NA='1e+23
Built-in potential: NA = 1e+17 cm^-3, ND = 1e+16 cm^-3, ni = 1.5e+10 cm^-3, T = 300 K, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Depletion width, field and capacitance of an abrupt pn junction, elx_depletion_width

The depletion-region width (and its parts on each side), the peak electric field and the depletion capacitance per area of an abrupt pn junction at a reverse bias (negative VR for a forward bias below Vbi).

\[W = \sqrt{\frac{2\varepsilon(V_{bi}+V_R)}{q}\left(\frac{1}{N_A}+\frac{1}{N_D}\right)}\]
inputmeaningcondition
NAacceptor concentration (p side)
NDdonor concentration (n side)
Vbibuilt-in potential
VRreverse bias (negative for forward)
eps_rrelative permittivity of the semiconductor (11.7 for silicon)
outputmeaning
Wdepletion width
W_umdepletion width in micrometres
xnwidth on the n side
xpwidth on the p side
Emaxpeak electric field (V/m)
Cj_areadepletion capacitance per area
Depletion width, field and capacitance of an abrupt pn junction: depletion width against donor concentratio…W (depletion width) against ND (donor concentration (n side)) from 1.0000e+21 1/m^3 to 1.0000e+23 1/m^3 on a logarithmic axis. One curve for each value of eps_r (relative permittivity of the semiconductor (11.7 for silicon)): 11.7, 5.85, 23.4. Other inputs as in the worked example: NA = 1e+23 1/m^3, Vbi = 0.81 V, VR = 5.0 V. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, ND = 1.0000e+22 1/m^3, W = 9.0910e-07 m.1.00e211.00e221.00e2301.00e-62.00e-63.00e-64.00e-69.0910e-07 meps_r = 11.7 (example)eps_r = 5.85eps_r = 23.4ND (donor concentration (n side) [1/m^3]W), depletion width [m]
W (depletion width) against ND (donor concentration (n side)) from 1.0000e+21 1/m^3 to 1.0000e+23 1/m^3 on a logarithmic axis. One curve for each value of eps_r (relative permittivity of the semiconductor (11.7 for silicon)): 11.7, 5.85, 23.4. Other inputs as in the worked example: NA = 1e+23 1/m^3, Vbi = 0.81 V, VR = 5.0 V. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, ND = 1.0000e+22 1/m^3, W = 9.0910e-07 m.
electronics_engineering_ai999x.solve('elx_depletion_width', NA=1e+23, ND=1e+22, Vbi=0.81, VR=5.0, eps_r=11.7)
# -> W = 9.091e-07 m, W_um = 0.9091, xn = 8.26454e-07 m, xp = 8.26454e-08 m, Emax = 1.27819e+07 N/C, Cj_area = 0.000113952 F/m^2   (SOLVED)
electronics_engineering_ai999x.solve('elx_depletion_width', NA=1e+22, ND=1e+22, Vbi=0.7, VR=0.0, eps_r=11.7)
# -> W = 4.25492e-07 m, W_um = 0.425492, xn = 2.12746e-07 m, xp = 2.12746e-07 m, Emax = 3.29031e+06 N/C, Cj_area = 0.000243469 F/m^2   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Depletion width: NA = 1e+17 cm^-3, ND = 1e+16 cm^-3, Vbi = 0.81 V, VR = 5 V, eps_r = 11.7SOLVEDW = 9.091e-07 m, W_um = 0.9091, xn = 8.26454e-07 m, xp = 8.26454e-08 m, Emax = 1.27819e+07 N/C, Cj_area = 0.000113952 F/m^2
Depletion width: NA = 1e+16 cm^-3, ND = 1e+16 cm^-3, Vbi = 0.7 V, VR = 0 V, eps_r = 11.7SOLVEDW = 4.25492e-07 m, W_um = 0.425492, xn = 2.12746e-07 m, xp = 2.12746e-07 m, Emax = 3.29031e+06 N/C, Cj_area = 0.000243469 F/m^2
Depletion width: ND = 1e+16 cm^-3, Vbi = 0.81 V, VR = 5 V, eps_r = 11.7NEEDS_INPUTelx_depletion_width needs NA (acceptor concentration (p side)). Example: solve('elx_depletion_width', NA='1e+23 1/m^3',
Depletion width: NA = 1e+17 cm^-3, ND = 1e+16 cm^-3, Vbi = 0.81 V, VR = 5 V, eps_r = 11.7, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Junction (depletion) capacitance versus bias, elx_junction_capacitance

The depletion capacitance of a pn junction at a reverse bias from its zero-bias value, the built-in potential and the grading coefficient (1/2 abrupt, $1/3$ linearly graded), as used for varactors.

\[C_j = \frac{C_{j0}}{\left(1 + V_R/V_{bi}\right)^{m}}\]
inputmeaningcondition
Cj0zero-bias junction capacitance
Vbibuilt-in potential
VRreverse bias (negative for forward)
mgrading coefficient (0.5 abrupt, 0.33 linearly graded)
outputmeaning
Cjjunction capacitance
ratio$Cj/Cj0$
Junction (depletion) capacitance versus bias: junction capacitance against grading coefficient (0.5 abrupt,…Cj (junction capacitance) against m (grading coefficient (0.5 abrupt, 0.33 linearly graded)) from 0.02 to 0.98. One curve for each value of Cj0 (zero-bias junction capacitance): 2.0000e-12 F, 1.0000e-12 F, 4.0000e-12 F. Other inputs as in the worked example: Vbi = 0.75 V, VR = 5.0 V. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, m = 0.5, Cj = 7.2232e-13 F.00.250.50.75101.00e-122.00e-123.00e-124.00e-127.2232e-13 FCj0 = 2.0000e-12 F (example)Cj0 = 1.0000e-12 FCj0 = 4.0000e-12 Fm (grading coefficientCj), junction capacitance [F]
Cj (junction capacitance) against m (grading coefficient (0.5 abrupt, 0.33 linearly graded)) from 0.02 to 0.98. One curve for each value of Cj0 (zero-bias junction capacitance): 2.0000e-12 F, 1.0000e-12 F, 4.0000e-12 F. Other inputs as in the worked example: Vbi = 0.75 V, VR = 5.0 V. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, m = 0.5, Cj = 7.2232e-13 F.
electronics_engineering_ai999x.solve('elx_junction_capacitance', Cj0=2e-12, Vbi=0.75, VR=5.0, m=0.5)
# -> Cj = 7.22315e-13 F, ratio = 0.361158   (SOLVED)
electronics_engineering_ai999x.solve('elx_junction_capacitance', Cj0=5e-11, Vbi=0.7, VR=2.0, m=0.33)
# -> Cj = 3.2026e-11 F, ratio = 0.640519   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Junction capacitance: Cj0 = 2 pF, Vbi = 0.75 V, VR = 5 V, m = 0.5SOLVEDCj = 7.22315e-13 F, ratio = 0.361158
Junction capacitance: Cj0 = 50 pF, Vbi = 0.7 V, VR = 2 V, m = 0.33SOLVEDCj = 3.2026e-11 F, ratio = 0.640519
Junction capacitance: Vbi = 0.75 V, VR = 5 V, m = 0.5NEEDS_INPUTelx_junction_capacitance needs Cj0 (zero-bias junction capacitance). Example: solve('elx_junction_capacitance', Cj0='2e-
Junction capacitance: Cj0 = 2 pF, Vbi = 0.75 V, VR = 5 V, m = 0.5, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Diode current from the Shockley equation, elx_shockley_diode_current

The current of a pn-junction diode at a terminal voltage from its saturation current, ideality factor and temperature (forward or reverse).

\[I_D = I_S\left(e^{V_D/nV_T} - 1\right)\]
inputmeaningcondition
Issaturation current
nideality (emission) factor, 1 to 2
VDdiode voltage (negative for reverse bias)
Tjunction temperature
outputmeaning
IDdiode current
VTthermal voltage
Diode current from the Shockley equation: diode current against ideality (emission) factor, 1 to 2ID (diode current) against n (ideality (emission) factor, 1 to 2) from 0.9 to 1.1. One curve for each value of VD (diode voltage (negative for reverse bias)): 0.65 V, 0.325 V, 1.3 V. Other inputs as in the worked example: Is = 1e-14 A, T = 300.0 K. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, n = 1, ID = 0.000830844 A.0.90.9511.051.105.00e91.00e101.50e100.000830844 AVD = 0.65 V (example)VD = 0.325 VVD = 1.3 Vn (ideality (emission) factor, 1 to 2ID), diode current [A]
ID (diode current) against n (ideality (emission) factor, 1 to 2) from 0.9 to 1.1. One curve for each value of VD (diode voltage (negative for reverse bias)): 0.65 V, 0.325 V, 1.3 V. Other inputs as in the worked example: Is = 1e-14 A, T = 300.0 K. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, n = 1, ID = 0.000830844 A.
electronics_engineering_ai999x.solve('elx_shockley_diode_current', Is=1e-14, n=1.0, VD=0.65, T=300.0)
# -> ID = 0.000830844 A, VT = 0.025852 V   (SOLVED)
electronics_engineering_ai999x.solve('elx_shockley_diode_current', Is=2e-12, n=1.8, VD=-2.0, T=300.0)
# -> ID = -2e-12 A, VT = 0.025852 V   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Shockley diode current: Is = 1e-14 A, n = 1, VD = 0.65 V, T = 300 KSOLVEDID = 0.000830844 A, VT = 0.025852 V
Shockley diode current: Is = 2e-12 A, n = 1.8, VD = -2 V, T = 300 KSOLVEDID = -2e-12 A, VT = 0.025852 V
Shockley diode current: n = 1, VD = 0.65 V, T = 300 KNEEDS_INPUTelx_shockley_diode_current needs Is (saturation current). Example: solve('elx_shockley_diode_current', Is='1e-14 A', n=1
Shockley diode current: Is = 1e-14 A, n = 1, VD = 0.65 V, T = 300 K, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Diode voltage for a given current, elx_diode_voltage

The voltage across a pn-junction diode carrying a given current (the inverse of the Shockley equation).

\[V_D = nV_T\ln\left(1 + \frac{I_D}{I_S}\right)\]
inputmeaningcondition
IDdiode current
Issaturation current
nideality factor
Tjunction temperature
outputmeaning
VDdiode voltage
VTthermal voltage
Diode voltage for a given current: diode voltage against ideality factorVD (diode voltage) against n (ideality factor) from 0.5 to 1.5. One curve for each value of T (junction temperature): 300 K, 150 K, 600 K. Other inputs as in the worked example: ID = 0.001 A, Is = 1e-14 A. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, n = 1, VD = 0.654791 V.0.50.7511.251.50.511.520.654791 VT = 300 K (example)T = 150 KT = 600 Kn (ideality factorVD), diode voltage [V]
VD (diode voltage) against n (ideality factor) from 0.5 to 1.5. One curve for each value of T (junction temperature): 300 K, 150 K, 600 K. Other inputs as in the worked example: ID = 0.001 A, Is = 1e-14 A. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, n = 1, VD = 0.654791 V.
electronics_engineering_ai999x.solve('elx_diode_voltage', ID=0.001, Is=1e-14, n=1.0, T=300.0)
# -> VD = 0.654791 V, VT = 0.025852 V   (SOLVED)
electronics_engineering_ai999x.solve('elx_diode_voltage', ID=0.02, Is=5e-12, n=1.7, T=320.0)
# -> VD = 1.03646 V, VT = 0.0275755 V   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Diode voltage for a current: ID = 0.001 A, Is = 1e-14 A, n = 1, T = 300 KSOLVEDVD = 0.654791 V, VT = 0.025852 V
Diode voltage for a current: ID = 0.02 A, Is = 5e-12 A, n = 1.7, T = 320 KSOLVEDVD = 1.03646 V, VT = 0.0275755 V
Diode voltage for a current: Is = 1e-14 A, n = 1, T = 300 KNEEDS_INPUTelx_diode_voltage needs ID (diode current). Example: solve('elx_diode_voltage', ID='0.001 A', Is='1e-14 A', n=1, T='300
Diode voltage for a current: ID = 0.001 A, Is = 1e-14 A, n = 1, T = 300 K, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Operating point of a diode in series with a resistor (exact), elx_diode_operating_point

The current and voltage of a forward-biased diode fed from a DC source through a resistor, solving the Shockley equation and Kirchhoff's voltage law together (no constant-drop approximation).

\[V_S = I_DR + nV_T\ln\left(1 + \frac{I_D}{I_S}\right)\]
inputmeaningcondition
VSsource voltage
Rseries resistance
Issaturation current
nideality factor
Tjunction temperature
outputmeaning
IDdiode current
VDdiode voltage
P_Dpower in the diode
ID against VS: Operating point of a diode in series with a resistor (exact)ID (diode current) against VS (source voltage), with Is = 1.00e-14 A, R = 1000 ohm, T = 300 K, n = 1. 31 points computed by electronics-engineering-ai999x; marked: VS = 5, ID = 0.00430746 A.460.0020.0040.0060.00430746 AVS, source voltage [V]ID [A]
ID (diode current) against VS (source voltage), with Is = 1.00e-14 A, R = 1000 ohm, T = 300 K, n = 1. 31 points computed by electronics-engineering-ai999x; marked: VS = 5, ID = 0.00430746 A.
Operating point of a diode in series with a resistor (exact): diode current against series resistanceID (diode current) against R (series resistance) from 500 ohm to 1500 ohm. One curve for each value of VS (source voltage): 5 V, 2.5 V, 10 V. Other inputs as in the worked example: Is = 1e-14 A, n = 1.0, T = 300.0 K. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R = 1000 ohm, ID = 0.00430746 A.50075010001250150000.0050.010.0150.00430746 AVS = 5 V (example)VS = 2.5 VVS = 10 VR (series resistance [ohm]ID), diode current [A]
ID (diode current) against R (series resistance) from 500 ohm to 1500 ohm. One curve for each value of VS (source voltage): 5 V, 2.5 V, 10 V. Other inputs as in the worked example: Is = 1e-14 A, n = 1.0, T = 300.0 K. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R = 1000 ohm, ID = 0.00430746 A.
electronics_engineering_ai999x.solve('elx_diode_operating_point', VS=5.0, R=1000.0, Is=1e-14, n=1.0, T=300.0)
# -> ID = 0.00430746 A, VD = 0.692544 V, P_D = 0.0029831 W   (SOLVED)
electronics_engineering_ai999x.solve('elx_diode_operating_point', VS=12.0, R=2200.0, Is=3e-09, n=1.9, T=300.0)
# -> ID = 0.00513409 A, VD = 0.704992 V, P_D = 0.0036195 W   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Diode operating point: VS = 5 V, R = 1000 ohm, Is = 1e-14 A, n = 1, T = 300 KSOLVEDID = 0.00430746 A, VD = 0.692544 V, P_D = 0.0029831 W
Diode operating point: VS = 12 V, R = 2200 ohm, Is = 3e-09 A, n = 1.9, T = 300 KSOLVEDID = 0.00513409 A, VD = 0.704992 V, P_D = 0.0036195 W
Diode operating point: R = 1000 ohm, Is = 1e-14 A, n = 1, T = 300 KNEEDS_INPUTelx_diode_operating_point needs VS (source voltage). Example: solve('elx_diode_operating_point', VS='5 V', R='1000 ohm',
Diode operating point: VS = 5 V, R = 1000 ohm, Is = 1e-14 A, n = 1, T = 300 K, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Rectifier output: average, RMS, ripple factor and PIV, elx_rectifier_averages

The DC (average) and RMS output voltage, ripple factor, peak inverse voltage and conduction angle of an unfiltered half-wave, bridge or centre-tapped full-wave rectifier with a constant diode drop (0 V for ideal diodes).

\[V_{dc} = \frac{k}{2\pi}\left[2V_m\cos\theta_1 - V(\pi - 2\theta_1)\right],\ \theta_1 = \arcsin\frac{V}{V_m}\]
inputmeaningcondition
Vmpeak AC voltage of the (secondary) winding
circuithalf-wave, bridge or center-tapped (Vm per half of the winding)
Vonforward drop of one diode (0 V for ideal diodes)
outputmeaning
Vp_outpeak output voltage
Vdcaverage output voltage
VrmsRMS output voltage
ripple_factorripple factor (AC rms / DC)
PIVpeak inverse voltage of a diode
conduction_degconduction angle per half cycle, degrees
Rectifier output: average, RMS, ripple factor and PIV: average output voltage against peak AC voltage of th…Vdc (average output voltage) against Vm (peak AC voltage of the (secondary) winding) from 5 V to 15 V. One curve for each value of Von (forward drop of one diode (0 V for ideal diodes)): 0 V, 0.5 V. Other inputs as in the worked example: circuit = half-wave. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Vm = 10 V, Vdc = 3.1831 V.57.51012.51523453.1831 VVon = 0 V (example)Von = 0.5 VVm (peak AC voltage of the [V]Vdc), average output voltage [V]
Vdc (average output voltage) against Vm (peak AC voltage of the (secondary) winding) from 5 V to 15 V. One curve for each value of Von (forward drop of one diode (0 V for ideal diodes)): 0 V, 0.5 V. Other inputs as in the worked example: circuit = half-wave. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Vm = 10 V, Vdc = 3.1831 V.
electronics_engineering_ai999x.solve('elx_rectifier_averages', Vm=10.0, circuit='half-wave', Von=0.0)
# -> Vp_out = 10 V, Vdc = 3.1831 V, Vrms = 5 V, ripple_factor = 1.21136, PIV = 10 V, conduction_deg = 180   (SOLVED)
electronics_engineering_ai999x.solve('elx_rectifier_averages', Vm=17.0, circuit='bridge', Von=0.7)
# -> Vp_out = 15.6 V, Vdc = 9.45926 V, Vrms = 10.776 V, ripple_factor = 0.545697, PIV = 16.3 V, conduction_deg = 170.552   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Rectifier output: Vm = 10 V, circuit = half-wave, Von = 0 VSOLVEDVp_out = 10 V, Vdc = 3.1831 V, Vrms = 5 V, ripple_factor = 1.21136, PIV = 10 V, conduction_deg = 180
Rectifier output: Vm = 17 V, circuit = bridge, Von = 0.7 VSOLVEDVp_out = 15.6 V, Vdc = 9.45926 V, Vrms = 10.776 V, ripple_factor = 0.545697, PIV = 16.3 V, conduction_deg = 170.552
Rectifier output: circuit = half-wave, Von = 0 VNEEDS_INPUTelx_rectifier_averages needs Vm (peak AC voltage of the (secondary) winding). Example: solve('elx_rectifier_averages', V
Rectifier output: Vm = 10 V, circuit = half-wave, Von = 0 V, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te
Rectifier output: Vm = 10 V, circuit = half wave, Von = 0 VSOLVEDVp_out = 10 V, Vdc = 3.1831 V, Vrms = 5 V, ripple_factor = 1.21136, PIV = 10 V, conduction_deg = 180

Capacitor-input filter: ripple voltage and DC output, elx_capacitor_filter_ripple

The peak-to-peak ripple, the DC output, the RMS ripple and the ripple factor of a rectifier with a smoothing capacitor and resistive load (small-ripple approximation).

\[V_r = \frac{V_p}{f_rR_LC},\quad V_{dc} = V_p - \frac{V_r}{2}\]
inputmeaningcondition
Vppeak rectified voltage (after the diode drops)
fline frequency
RLload resistance
Cfilter capacitance
circuithalf-wave or full-wave rectification
outputmeaning
f_rippleripple frequency
Vrpeak-to-peak ripple
VdcDC output voltage
Vr_rmsRMS ripple
ripple_factorripple factor
Capacitor-input filter: ripple voltage and DC output: peak-to-peak ripple against line frequencyVr (peak-to-peak ripple) against f (line frequency) from 30 Hz to 90 Hz. One curve for each value of Vp (peak rectified voltage (after the diode drops)): 16.3 V, 8.15 V, 32.6 V. Other inputs as in the worked example: RL = 500.0 ohm, C = 0.001 F, circuit = full-wave. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, f = 60 Hz, Vr = 0.271667 V.4060800.250.50.7510.271667 VVp = 16.3 V (example)Vp = 8.15 VVp = 32.6 Vf (line frequency [Hz]Vr), peak-to-peak ripple [V]
Vr (peak-to-peak ripple) against f (line frequency) from 30 Hz to 90 Hz. One curve for each value of Vp (peak rectified voltage (after the diode drops)): 16.3 V, 8.15 V, 32.6 V. Other inputs as in the worked example: RL = 500.0 ohm, C = 0.001 F, circuit = full-wave. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, f = 60 Hz, Vr = 0.271667 V.
electronics_engineering_ai999x.solve('elx_capacitor_filter_ripple', Vp=16.3, f=60.0, RL=500.0, C=0.001, circuit='full-wave')
# -> f_ripple = 120 Hz, Vr = 0.271667 V, Vdc = 16.1642 V, Vr_rms = 0.0784234 V, ripple_factor = 0.00485168   (SOLVED)
electronics_engineering_ai999x.solve('elx_capacitor_filter_ripple', Vp=12.0, f=50.0, RL=1000.0, C=0.00047, circuit='half-wave')
# -> f_ripple = 50 Hz, Vr = 0.510638 V, Vdc = 11.7447 V, Vr_rms = 0.147409 V, ripple_factor = 0.0125511   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Capacitor filter ripple: Vp = 16.3 V, f = 60 Hz, RL = 500 ohm, C = 1000 uF, circuit = full-waveSOLVEDf_ripple = 120 Hz, Vr = 0.271667 V, Vdc = 16.1642 V, Vr_rms = 0.0784234 V, ripple_factor = 0.00485168
Capacitor filter ripple: Vp = 12 V, f = 50 Hz, RL = 1000 ohm, C = 470 uF, circuit = half-waveSOLVEDf_ripple = 50 Hz, Vr = 0.510638 V, Vdc = 11.7447 V, Vr_rms = 0.147409 V, ripple_factor = 0.0125511
Capacitor filter ripple: f = 60 Hz, RL = 500 ohm, C = 1000 uF, circuit = full-waveNEEDS_INPUTelx_capacitor_filter_ripple needs Vp (peak rectified voltage (after the diode drops)). Example: solve('elx_capacitor_fil
Capacitor filter ripple: Vp = 16.3 V, f = 60 Hz, RL = 500 ohm, C = 1000 uF, circuit = full-wave, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Zener shunt regulator: load voltage and currents, elx_zener_regulator

The output voltage and the source, load and Zener currents and the Zener power of a Zener shunt regulator (series resistor, Zener across the load), with an optional Zener resistance.

\[I_Z = \frac{V_{in} - V_Z}{R_S} - \frac{V_Z}{R_L}\]
inputmeaningcondition
Vininput voltage
Rsseries resistance
VzZener (breakdown) voltage
RLload resistance
rzZener resistance (0 for an ideal Zener)
outputmeaning
Voutload voltage
I_scurrent in the series resistor
I_Lload current
I_zZener current
P_zZener power
Zener shunt regulator: load voltage and currents: Zener current against series resistanceI_z (Zener current) against Rs (series resistance) from 22 ohm to 2200 ohm on a logarithmic axis. One curve for each value of Vin (input voltage): 20 V, 40 V. Other inputs as in the worked example: Vz = 10.0 V, RL = 1000.0 ohm. 34 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Rs = 220 ohm, I_z = 0.0354545 A.100100000.510.0354545 AVin = 20 V (example)Vin = 40 VRs (series resistance [ohm]I_z), Zener current [A]
I_z (Zener current) against Rs (series resistance) from 22 ohm to 2200 ohm on a logarithmic axis. One curve for each value of Vin (input voltage): 20 V, 40 V. Other inputs as in the worked example: Vz = 10.0 V, RL = 1000.0 ohm. 34 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Rs = 220 ohm, I_z = 0.0354545 A.
electronics_engineering_ai999x.solve('elx_zener_regulator', Vin=20.0, Rs=220.0, Vz=10.0, RL=1000.0)
# -> Vout = 10 V, I_s = 0.0454545 A, I_L = 0.01 A, I_z = 0.0354545 A, P_z = 0.354545 W   (SOLVED)
electronics_engineering_ai999x.solve('elx_zener_regulator', Vin=15.0, Rs=100.0, Vz=5.1, RL=470.0, rz=7.0)
# -> Vout = 5.66876 V, I_s = 0.0933124 A, I_L = 0.0120612 A, I_z = 0.0812512 A, P_z = 0.460594 W   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Zener regulator: Vin = 20 V, Rs = 220 ohm, Vz = 10 V, RL = 1000 ohmSOLVEDVout = 10 V, I_s = 0.0454545 A, I_L = 0.01 A, I_z = 0.0354545 A, P_z = 0.354545 W
Zener regulator: Vin = 15 V, Rs = 100 ohm, Vz = 5.1 V, RL = 470 ohm, rz = 7 ohmSOLVEDVout = 5.66876 V, I_s = 0.0933124 A, I_L = 0.0120612 A, I_z = 0.0812512 A, P_z = 0.460594 W
Zener regulator: Rs = 220 ohm, Vz = 10 V, RL = 1000 ohmNEEDS_INPUTelx_zener_regulator needs Vin (input voltage). Example: solve('elx_zener_regulator', Vin='20 V', Rs='220 ohm', Vz='10 V'
Zener regulator: Vin = 20 V, Rs = 220 ohm, Vz = 10 V, RL = 1000 ohm, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te
Zener regulator: Vin = 12 V, Rs = 1 kohm, Vz = 9 V, RL = 1 kohmINVALID_INPUTZener shunt regulator: load voltage and currents: the Zener is not in breakdown: the open-circuit voltage across the loa

Zener regulator design: series resistor and Zener rating, elx_zener_series_resistor_design

The largest series resistance that keeps a Zener regulator in regulation at the lowest input and largest load, and the resulting worst-case Zener current and power (highest input, smallest load) and resistor power.

\[R_S = \frac{V_{in,min} - V_Z}{I_{Z,min} + I_{L,max}}\]
inputmeaningcondition
Vin_minlowest input voltage
Vin_maxhighest input voltage
VzZener voltage
IL_minsmallest load current
IL_maxlargest load current
Iz_minminimum Zener current for regulation
outputmeaning
Rs_maxlargest series resistance
Iz_maxworst-case Zener current
Pz_maxworst-case Zener power
PRs_maxworst-case resistor power
Zener regulator design: series resistor and Zener rating: largest series resistance against largest load cu…Rs_max (largest series resistance) against IL_max (largest load current) from 0.005 A to 0.5 A on a logarithmic axis. One curve for each value of Vz (Zener voltage): 9.1 V, 4.55 V. Other inputs as in the worked example: Vin_min = 12.0 V, Vin_max = 15.0 V, IL_min = 0.0 A, Iz_min = 0.005 A. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, IL_max = 0.05 A, Rs_max = 52.7273 ohm.0.010.1020040060080052.7273 ohmVz = 9.1 V (example)Vz = 4.55 VIL_max (largest load current [A]Rs_max), largest series resistance [ohm]
Rs_max (largest series resistance) against IL_max (largest load current) from 0.005 A to 0.5 A on a logarithmic axis. One curve for each value of Vz (Zener voltage): 9.1 V, 4.55 V. Other inputs as in the worked example: Vin_min = 12.0 V, Vin_max = 15.0 V, IL_min = 0.0 A, Iz_min = 0.005 A. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, IL_max = 0.05 A, Rs_max = 52.7273 ohm.
electronics_engineering_ai999x.solve('elx_zener_series_resistor_design', Vin_min=12.0, Vin_max=15.0, Vz=9.1, IL_min=0.0, IL_max=0.05, Iz_min=0.005)
# -> Rs_max = 52.7273 ohm, Iz_max = 0.111897 A, Pz_max = 1.01826 W, PRs_max = 0.66019 W   (SOLVED)
electronics_engineering_ai999x.solve('elx_zener_series_resistor_design', Vin_min=9.0, Vin_max=11.0, Vz=5.6, IL_min=0.01, IL_max=0.1, Iz_min=0.002)
# -> Rs_max = 33.3333 ohm, Iz_max = 0.152 A, Pz_max = 0.8512 W, PRs_max = 0.8748 W   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Zener regulator design: Vin_min = 12 V, Vin_max = 15 V, Vz = 9.1 V, IL_min = 0 mA, IL_max = 50 mA, Iz_min = 5 mASOLVEDRs_max = 52.7273 ohm, Iz_max = 0.111897 A, Pz_max = 1.01826 W, PRs_max = 0.66019 W
Zener regulator design: Vin_min = 9 V, Vin_max = 11 V, Vz = 5.6 V, IL_min = 10 mA, IL_max = 100 mA, Iz_min = 2 mASOLVEDRs_max = 33.3333 ohm, Iz_max = 0.152 A, Pz_max = 0.8512 W, PRs_max = 0.8748 W
Zener regulator design: Vin_max = 15 V, Vz = 9.1 V, IL_min = 0 mA, IL_max = 50 mA, Iz_min = 5 mANEEDS_INPUTelx_zener_series_resistor_design needs Vin_min (lowest input voltage). Example: solve('elx_zener_series_resistor_design'
Zener regulator design: Vin_min = 12 V, Vin_max = 15 V, Vz = 9.1 V, IL_min = 0 mA, IL_max = 50 mA, Iz_min = 5 mA, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

LED series (current-limiting) resistor, elx_led_series_resistor

The current-limiting resistor for one LED or a string of LEDs in series at a chosen forward current, and the power in the resistor and in the LEDs.

\[R = \frac{V_S - nV_F}{I_F}\]
inputmeaningcondition
Vssupply voltage
Vfforward voltage of one LED
IfLED forward current
nnumber of LEDs in series (default 1)
outputmeaning
Rseries resistance
P_Rpower in the resistor
P_LEDpower in the LEDs
LED series (current-limiting) resistor: series resistance against LED forward currentR (series resistance) against If (LED forward current) from 0.01 A to 0.03 A. One curve for each value of Vs (supply voltage): 5 V, 2.5 V, 10 V. Other inputs as in the worked example: Vf = 2.0 V. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, If = 0.02 A, R = 150 ohm.0.010.0150.020.0250.030200400600800150 ohmVs = 5 V (example)Vs = 2.5 VVs = 10 VIf (LED forward current [A]R), series resistance [ohm]
R (series resistance) against If (LED forward current) from 0.01 A to 0.03 A. One curve for each value of Vs (supply voltage): 5 V, 2.5 V, 10 V. Other inputs as in the worked example: Vf = 2.0 V. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, If = 0.02 A, R = 150 ohm.
electronics_engineering_ai999x.solve('elx_led_series_resistor', Vs=5.0, Vf=2.0, If=0.02)
# -> R = 150 ohm, P_R = 0.06 W, P_LED = 0.04 W   (SOLVED)
electronics_engineering_ai999x.solve('elx_led_series_resistor', Vs=12.0, Vf=3.1, If=0.015, n=3)
# -> R = 180 ohm, P_R = 0.0405 W, P_LED = 0.1395 W   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
LED series resistor: Vs = 5 V, Vf = 2 V, If = 20 mASOLVEDR = 150 ohm, P_R = 0.06 W, P_LED = 0.04 W
LED series resistor: Vs = 12 V, Vf = 3.1 V, If = 15 mA, n = 3SOLVEDR = 180 ohm, P_R = 0.0405 W, P_LED = 0.1395 W
LED series resistor: Vf = 2 V, If = 20 mANEEDS_INPUTelx_led_series_resistor needs Vs (supply voltage). Example: solve('elx_led_series_resistor', Vs='5 V', Vf='2 V', If='0.0
LED series resistor: Vs = 5 V, Vf = 2 V, If = 20 mA, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

BJT terminal currents from beta, elx_bjt_current_relations

The collector and emitter currents and the common-base current gain alpha of a bipolar transistor in the active region from its base current and beta.

\[I_C = \beta I_B,\quad I_E = (\beta+1)I_B,\quad \alpha = \frac{\beta}{\beta+1}\]
inputmeaningcondition
IBbase current
betacommon-emitter current gain (hFE)
outputmeaning
ICcollector current
IEemitter current
alpha$\alpha = \beta/(\beta + 1)$
BJT terminal currents from beta: collector current against base currentIC (collector current) against IB (base current) from 1.0000e-05 A to 3.0000e-05 A. One curve for each value of beta (common-emitter current gain (hFE)): 100, 50, 200. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, IB = 2.0000e-05 A, IC = 0.002 A.1.00e-51.50e-52.00e-52.50e-53.00e-50.0020.0040.0060.002 Abeta = 100 (example)beta = 50beta = 200IB (base current [A]IC), collector current [A]
IC (collector current) against IB (base current) from 1.0000e-05 A to 3.0000e-05 A. One curve for each value of beta (common-emitter current gain (hFE)): 100, 50, 200. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, IB = 2.0000e-05 A, IC = 0.002 A.
BJT terminal currents from beta: collector current over base current and common-emitter current gain (hFE)IC (collector current) over IB (base current) from 1.0000e-05 A to 3.0000e-05 A and beta (common-emitter current gain (hFE)) from 50 to 150: each of the 21 × 15 cells is one run of electronics-engineering-ai999x, shaded by its value (light 0.0005 A to dark 0.0045 A); iso-lines at IC = 0.001, 0.002, 0.003, 0.004 A. Marked: the worked example, IB = 2.0000e-05 A, beta = 100, IC = 0.002 A.1.00e-51.50e-52.00e-52.50e-53.00e-550751001251500.0010.0020.0030.0040.002 A0.00455.00e-4ICIB (base current [A]beta), common-emitter current gain (hFE)
IC (collector current) over IB (base current) from 1.0000e-05 A to 3.0000e-05 A and beta (common-emitter current gain (hFE)) from 50 to 150: each of the 21 × 15 cells is one run of electronics-engineering-ai999x, shaded by its value (light 0.0005 A to dark 0.0045 A); iso-lines at IC = 0.001, 0.002, 0.003, 0.004 A. Marked: the worked example, IB = 2.0000e-05 A, beta = 100, IC = 0.002 A.
electronics_engineering_ai999x.solve('elx_bjt_current_relations', IB=2e-05, beta=100.0)
# -> IC = 0.002 A, IE = 0.00202 A, alpha = 0.990099   (SOLVED)
electronics_engineering_ai999x.solve('elx_bjt_current_relations', IB=5e-05, beta=150.0)
# -> IC = 0.0075 A, IE = 0.00755 A, alpha = 0.993377   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
BJT currents: IB = 20 uA, beta = 100SOLVEDIC = 0.002 A, IE = 0.00202 A, alpha = 0.990099
BJT currents: IB = 50 uA, beta = 150SOLVEDIC = 0.0075 A, IE = 0.00755 A, alpha = 0.993377
BJT currents: beta = 100NEEDS_INPUTelx_bjt_current_relations needs IB (base current). Example: solve('elx_bjt_current_relations', IB='2e-05 A', beta=100).
BJT currents: IB = 20 uA, beta = 100, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

BJT fixed (base-resistor) bias: Q-point, elx_bjt_fixed_bias

The quiescent base and collector currents and the collector-emitter voltage of a common-emitter stage biased by a single base resistor from the supply.

\[I_B = \frac{V_{CC} - V_{BE}}{R_B},\quad V_{CE} = V_{CC} - \beta I_BR_C\]
inputmeaningcondition
VCCsupply voltage
RBbase resistor
RCcollector resistor
betacurrent gain
VBEbase-emitter voltage (about 0.7 V)
outputmeaning
IBbase current
ICcollector current
IEemitter current
VCEcollector-emitter voltage
BJT fixed (base-resistor) bias: Q-point: collector current against base resistorIC (collector current) against RB (base resistor) from 235000 ohm to 705000 ohm. One curve for each value of VCC (supply voltage): 12 V, 6 V, 24 V. Other inputs as in the worked example: RC = 2200.0 ohm, beta = 100.0, VBE = 0.7 V. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, RB = 470000 ohm, IC = 0.00240426 A.4.00e56.00e50.00250.0050.00750.010.00240426 AVCC = 12 V (example)VCC = 6 VVCC = 24 VRB (base resistor [ohm]IC), collector current [A]
IC (collector current) against RB (base resistor) from 235000 ohm to 705000 ohm. One curve for each value of VCC (supply voltage): 12 V, 6 V, 24 V. Other inputs as in the worked example: RC = 2200.0 ohm, beta = 100.0, VBE = 0.7 V. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, RB = 470000 ohm, IC = 0.00240426 A.
electronics_engineering_ai999x.solve('elx_bjt_fixed_bias', VCC=12.0, RB=470000.0, RC=2200.0, beta=100.0, VBE=0.7)
# -> IB = 2.40426e-05 A, IC = 0.00240426 A, IE = 0.0024283 A, VCE = 6.71064 V   (SOLVED)
electronics_engineering_ai999x.solve('elx_bjt_fixed_bias', VCC=9.0, RB=820000.0, RC=2200.0, beta=200.0, VBE=0.65)
# -> IB = 1.01829e-05 A, IC = 0.00203659 A, IE = 0.00204677 A, VCE = 4.51951 V   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
BJT fixed bias: VCC = 12 V, RB = 470000 ohm, RC = 2200 ohm, beta = 100, VBE = 0.7 VSOLVEDIB = 2.40426e-05 A, IC = 0.00240426 A, IE = 0.0024283 A, VCE = 6.71064 V
BJT fixed bias: VCC = 9 V, RB = 820000 ohm, RC = 2200 ohm, beta = 200, VBE = 0.65 VSOLVEDIB = 1.01829e-05 A, IC = 0.00203659 A, IE = 0.00204677 A, VCE = 4.51951 V
BJT fixed bias: RB = 470000 ohm, RC = 2200 ohm, beta = 100, VBE = 0.7 VNEEDS_INPUTelx_bjt_fixed_bias needs VCC (supply voltage). Example: solve('elx_bjt_fixed_bias', VCC='12 V', RB='470000 ohm', RC='220
BJT fixed bias: VCC = 12 V, RB = 470000 ohm, RC = 2200 ohm, beta = 100, VBE = 0.7 V, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te
BJT fixed bias: VCC = 12 V, RB = 100 kohm, RC = 4.7 kohm, beta = 100, VBE = 0.7 VINVALID_INPUTBJT fixed (base-resistor) bias: Q-point: the transistor is saturated (VCE below 0.2 V): the active-region bias equations

BJT voltage-divider bias: exact Q-point, elx_bjt_voltage_divider_bias

The Q-point (base, collector and emitter currents, node voltages and VCE) of a common-emitter stage with a base voltage divider and an emitter resistor, by the exact Thevenin analysis (base current included).

\[I_B = \frac{V_{TH} - V_{BE}}{R_{TH} + (\beta+1)R_E}\]
inputmeaningcondition
VCCsupply voltage
R1upper divider resistor (supply to base)
R2lower divider resistor (base to ground)
RCcollector resistor
REemitter resistor
betacurrent gain
VBEbase-emitter voltage
outputmeaning
VTHThevenin voltage of the divider
RTHThevenin resistance of the divider
IBbase current
ICcollector current
IEemitter current
VBbase voltage
VEemitter voltage
VCcollector voltage
VCEcollector-emitter voltage
BJT voltage-divider bias: exact Q-point: collector current against emitter resistorIC (collector current) against RE (emitter resistor) from 235 ohm to 705 ohm. One curve for each value of VCC (supply voltage): 12 V, 6 V, 24 V. Other inputs as in the worked example: R1 = 47000.0 ohm, R2 = 10000.0 ohm, RC = 2200.0 ohm, beta = 150.0, VBE = 0.7 V. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, RE = 470 ohm, IC = 0.00266096 A.40060000.00250.0050.00750.00266096 AVCC = 12 V (example)VCC = 6 VVCC = 24 VRE (emitter resistor [ohm]IC), collector current [A]
IC (collector current) against RE (emitter resistor) from 235 ohm to 705 ohm. One curve for each value of VCC (supply voltage): 12 V, 6 V, 24 V. Other inputs as in the worked example: R1 = 47000.0 ohm, R2 = 10000.0 ohm, RC = 2200.0 ohm, beta = 150.0, VBE = 0.7 V. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, RE = 470 ohm, IC = 0.00266096 A.
electronics_engineering_ai999x.solve('elx_bjt_voltage_divider_bias', VCC=12.0, R1=47000.0, R2=10000.0, RC=2200.0, RE=470.0, beta=150.0, VBE=0.7)
# -> VTH = 2.10526 V, RTH = 8245.61 ohm, IB = 1.77397e-05 A, IC = 0.00266096 A, IE = 0.0026787 A, VB = 1.95899 V, VE = 1.25899 V, VC = 6.14589 V, VCE = 4.8869 V   (SOLVED)
electronics_engineering_ai999x.solve('elx_bjt_voltage_divider_bias', VCC=15.0, R1=33000.0, R2=6800.0, RC=3300.0, RE=1000.0, beta=100.0, VBE=0.7)
# -> VTH = 2.56281 V, RTH = 5638.19 ohm, IB = 1.74685e-05 A, IC = 0.00174685 A, IE = 0.00176432 A, VB = 2.46432 V, VE = 1.76432 V, VC = 9.23538 V, VCE = 7.47106 V   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
BJT voltage-divider bias: VCC = 12 V, R1 = 47000 ohm, R2 = 10000 ohm, RC = 2200 ohm, RE = 470 ohm, beta = 150, VBE = 0.7 VSOLVEDVTH = 2.10526 V, RTH = 8245.61 ohm, IB = 1.77397e-05 A, IC = 0.00266096 A, IE = 0.0026787 A, VB = 1.95899 V, VE = 1.25899 V, VC = 6.14589 V, VCE = 4.8869 V
BJT voltage-divider bias: VCC = 15 V, R1 = 33000 ohm, R2 = 6800 ohm, RC = 3300 ohm, RE = 1000 ohm, beta = 100, VBE = 0.7 VSOLVEDVTH = 2.56281 V, RTH = 5638.19 ohm, IB = 1.74685e-05 A, IC = 0.00174685 A, IE = 0.00176432 A, VB = 2.46432 V, VE = 1.76432 V, VC = 9.23538 V, VCE = 7.47106 V
BJT voltage-divider bias: R1 = 47000 ohm, R2 = 10000 ohm, RC = 2200 ohm, RE = 470 ohm, beta = 150, VBE = 0.7 VNEEDS_INPUTelx_bjt_voltage_divider_bias needs VCC (supply voltage). Example: solve('elx_bjt_voltage_divider_bias', VCC='12 V', R1='
BJT voltage-divider bias: VCC = 12 V, R1 = 47000 ohm, R2 = 10000 ohm, RC = 2200 ohm, RE = 470 ohm, beta = 150, VBE = 0.7 V, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

BJT dual-supply emitter bias: Q-point, elx_bjt_emitter_bias

The Q-point of a transistor with its base returned to ground through RB and its emitter returned to a negative supply -VEE through RE (emitter bias).

\[I_E = \frac{V_{EE} - V_{BE}}{R_E + R_B/(\beta+1)}\]
inputmeaningcondition
VCCpositive supply
VEEmagnitude of the negative supply
RBbase resistor to ground
RCcollector resistor
REemitter resistor to -VEE
betacurrent gain
VBEbase-emitter voltage
outputmeaning
IBbase current
ICcollector current
IEemitter current
VBbase voltage
VEemitter voltage
VCcollector voltage
VCEcollector-emitter voltage
BJT dual-supply emitter bias: Q-point: emitter current against emitter resistor to -VEEIE (emitter current) against RE (emitter resistor to -VEE) from 5000 ohm to 15000 ohm. One curve for each value of VEE (magnitude of the negative supply): 10 V, 5 V, 20 V. Other inputs as in the worked example: VCC = 10.0 V, RB = 10000.0 ohm, RC = 4700.0 ohm, beta = 100.0, VBE = 0.7 V. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, RE = 10000 ohm, IE = 0.000920882 A.500075001000012500150005.00e-40.0010.00150.0020.000920882 AVEE = 10 V (example)VEE = 5 VVEE = 20 VRE (emitter resistor to -VEE [ohm]IE), emitter current [A]
IE (emitter current) against RE (emitter resistor to -VEE) from 5000 ohm to 15000 ohm. One curve for each value of VEE (magnitude of the negative supply): 10 V, 5 V, 20 V. Other inputs as in the worked example: VCC = 10.0 V, RB = 10000.0 ohm, RC = 4700.0 ohm, beta = 100.0, VBE = 0.7 V. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, RE = 10000 ohm, IE = 0.000920882 A.
electronics_engineering_ai999x.solve('elx_bjt_emitter_bias', VCC=10.0, VEE=10.0, RB=10000.0, RC=4700.0, RE=10000.0, beta=100.0, VBE=0.7)
# -> IB = 9.11765e-06 A, IC = 0.000911765 A, IE = 0.000920882 A, VB = -0.0911765 V, VE = -0.791176 V, VC = 5.71471 V, VCE = 6.50588 V   (SOLVED)
electronics_engineering_ai999x.solve('elx_bjt_emitter_bias', VCC=12.0, VEE=9.0, RB=47000.0, RC=5600.0, RE=8200.0, beta=200.0, VBE=0.65)
# -> IB = 4.92567e-06 A, IC = 0.000985134 A, IE = 0.00099006 A, VB = -0.231507 V, VE = -0.881507 V, VC = 6.48325 V, VCE = 7.36475 V   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
BJT emitter bias: VCC = 10 V, VEE = 10 V, RB = 10000 ohm, RC = 4700 ohm, RE = 10000 ohm, beta = 100, VBE = 0.7 VSOLVEDIB = 9.11765e-06 A, IC = 0.000911765 A, IE = 0.000920882 A, VB = -0.0911765 V, VE = -0.791176 V, VC = 5.71471 V, VCE = 6.50588 V
BJT emitter bias: VCC = 12 V, VEE = 9 V, RB = 47000 ohm, RC = 5600 ohm, RE = 8200 ohm, beta = 200, VBE = 0.65 VSOLVEDIB = 4.92567e-06 A, IC = 0.000985134 A, IE = 0.00099006 A, VB = -0.231507 V, VE = -0.881507 V, VC = 6.48325 V, VCE = 7.36475 V
BJT emitter bias: VEE = 10 V, RB = 10000 ohm, RC = 4700 ohm, RE = 10000 ohm, beta = 100, VBE = 0.7 VNEEDS_INPUTelx_bjt_emitter_bias needs VCC (positive supply). Example: solve('elx_bjt_emitter_bias', VCC='10 V', VEE='10 V', RB='100
BJT emitter bias: VCC = 10 V, VEE = 10 V, RB = 10000 ohm, RC = 4700 ohm, RE = 10000 ohm, beta = 100, VBE = 0.7 V, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

BJT collector-feedback bias: Q-point, elx_bjt_collector_feedback_bias

The Q-point of a transistor biased by a resistor from collector to base (collector feedback), with an optional emitter resistor.

\[I_B = \frac{V_{CC} - V_{BE}}{R_F + (\beta+1)(R_C + R_E)}\]
inputmeaningcondition
VCCsupply voltage
RCcollector resistor (carries IC + IB)
RFfeedback resistor, collector to base
betacurrent gain
VBEbase-emitter voltage
REemitter resistor (default 0)
outputmeaning
IBbase current
ICcollector current
IEemitter current
VCcollector voltage
VCEcollector-emitter voltage
BJT collector-feedback bias: Q-point: collector current against collector resistor (carries IC + IB)IC (collector current) against RC (collector resistor (carries IC + IB)) from 470 ohm to 47000 ohm on a logarithmic axis. One curve for each value of VCC (supply voltage): 10 V, 5 V, 20 V. Other inputs as in the worked example: RF = 250000.0 ohm, beta = 90.0, VBE = 0.7 V. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, RC = 4700 ohm, IC = 0.00123506 A.10001000000.0020.0040.0060.00123506 AVCC = 10 V (example)VCC = 5 VVCC = 20 VRC (collector resistor [ohm]IC), collector current [A]
IC (collector current) against RC (collector resistor (carries IC + IB)) from 470 ohm to 47000 ohm on a logarithmic axis. One curve for each value of VCC (supply voltage): 10 V, 5 V, 20 V. Other inputs as in the worked example: RF = 250000.0 ohm, beta = 90.0, VBE = 0.7 V. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, RC = 4700 ohm, IC = 0.00123506 A.
electronics_engineering_ai999x.solve('elx_bjt_collector_feedback_bias', VCC=10.0, RC=4700.0, RF=250000.0, beta=90.0, VBE=0.7)
# -> IB = 1.37229e-05 A, IC = 0.00123506 A, IE = 0.00124878 A, VC = 4.13072 V, VCE = 4.13072 V   (SOLVED)
electronics_engineering_ai999x.solve('elx_bjt_collector_feedback_bias', VCC=12.0, RC=3300.0, RF=330000.0, beta=120.0, VBE=0.7, RE=470.0)
# -> IB = 1.43735e-05 A, IC = 0.00172482 A, IE = 0.00173919 A, VC = 6.26067 V, VCE = 5.44325 V   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
BJT collector-feedback bias: VCC = 10 V, RC = 4700 ohm, RF = 250000 ohm, beta = 90, VBE = 0.7 VSOLVEDIB = 1.37229e-05 A, IC = 0.00123506 A, IE = 0.00124878 A, VC = 4.13072 V, VCE = 4.13072 V
BJT collector-feedback bias: VCC = 12 V, RC = 3300 ohm, RF = 330000 ohm, beta = 120, VBE = 0.7 V, RE = 470 ohmSOLVEDIB = 1.43735e-05 A, IC = 0.00172482 A, IE = 0.00173919 A, VC = 6.26067 V, VCE = 5.44325 V
BJT collector-feedback bias: RC = 4700 ohm, RF = 250000 ohm, beta = 90, VBE = 0.7 VNEEDS_INPUTelx_bjt_collector_feedback_bias needs VCC (supply voltage). Example: solve('elx_bjt_collector_feedback_bias', VCC='10 V'
BJT collector-feedback bias: VCC = 10 V, RC = 4700 ohm, RF = 250000 ohm, beta = 90, VBE = 0.7 V, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

BJT small-signal (hybrid-pi) parameters, elx_bjt_small_signal_parameters

The transconductance gm, the input resistance r_pi, the emitter resistance r_e, the output resistance r_o (Early voltage) and the intrinsic gain of a bipolar transistor at its bias current.

\[g_m = \frac{I_C}{V_T},\quad r_\pi = \frac{\beta}{g_m},\quad r_e = \frac{\alpha}{g_m},\quad r_o = \frac{V_A}{I_C}\]
inputmeaningcondition
ICcollector bias current
betacurrent gain
VTthermal voltage (25 or 26 mV)
VAEarly voltage
outputmeaning
gmtransconductance
r_pibase input resistance r_pi
r_eemitter resistance r_e
r_ooutput resistance
A0intrinsic voltage gain gm r_o
BJT small-signal (hybrid-pi) parameters: transconductance against thermal voltage (25 or 26 mV)gm (transconductance) against VT (thermal voltage (25 or 26 mV)) from 0.0125 V to 0.0375 V. One curve for each value of IC (collector bias current): 0.001 A, 0.0005 A, 0.002 A. Other inputs as in the worked example: beta = 100.0, VA = 100.0 V. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, VT = 0.025 V, gm = 0.04 S.0.020.030.050.10.150.04 SIC = 0.001 A (example)IC = 0.0005 AIC = 0.002 AVT (thermal voltage (25 or 26 mV) [V]gm), transconductance [S]
gm (transconductance) against VT (thermal voltage (25 or 26 mV)) from 0.0125 V to 0.0375 V. One curve for each value of IC (collector bias current): 0.001 A, 0.0005 A, 0.002 A. Other inputs as in the worked example: beta = 100.0, VA = 100.0 V. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, VT = 0.025 V, gm = 0.04 S.
electronics_engineering_ai999x.solve('elx_bjt_small_signal_parameters', IC=0.001, beta=100.0, VT=0.025, VA=100.0)
# -> gm = 0.04 S, r_pi = 2500 ohm, r_e = 24.7525 ohm, r_o = 100000 ohm, A0 = 4000   (SOLVED)
electronics_engineering_ai999x.solve('elx_bjt_small_signal_parameters', IC=0.0025, beta=150.0, VT=0.026, VA=75.0)
# -> gm = 0.0961538 S, r_pi = 1560 ohm, r_e = 10.3311 ohm, r_o = 30000 ohm, A0 = 2884.62   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
BJT small-signal parameters: IC = 1 mA, beta = 100, VT = 25 mV, VA = 100 VSOLVEDgm = 0.04 S, r_pi = 2500 ohm, r_e = 24.7525 ohm, r_o = 100000 ohm, A0 = 4000
BJT small-signal parameters: IC = 2.5 mA, beta = 150, VT = 26 mV, VA = 75 VSOLVEDgm = 0.0961538 S, r_pi = 1560 ohm, r_e = 10.3311 ohm, r_o = 30000 ohm, A0 = 2884.62
BJT small-signal parameters: beta = 100, VT = 25 mV, VA = 100 VNEEDS_INPUTelx_bjt_small_signal_parameters needs IC (collector bias current). Example: solve('elx_bjt_small_signal_parameters', IC=
BJT small-signal parameters: IC = 1 mA, beta = 100, VT = 25 mV, VA = 100 V, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Common-emitter amplifier: gain, input and output resistance, elx_common_emitter_amplifier

The voltage gain (base to collector and source to load), the input and output resistances of a common-emitter stage with an optional unbypassed emitter resistance, from the bias current (hybrid-pi model, r_o neglected).

\[A_v = -\frac{\beta\,(R_C\parallel R_L)}{r_\pi + (\beta+1)R_{E1}}\]
inputmeaningcondition
ICcollector bias current
betacurrent gain
VTthermal voltage
RCcollector resistor
RLload resistor
RE1unbypassed emitter resistance (0 if fully bypassed)
RBbias resistance seen at the base (R1 || R2)
Rsigsource resistance
outputmeaning
gmtransconductance
r_pir_pi
Avvoltage gain base to output
Rininput resistance (including RB)
Routoutput resistance (RC)
Gvoverall gain from the source voltage
Common-emitter amplifier: gain, input and output resistance: voltage gain base to output against thermal vo…Av (voltage gain base to output) against VT (thermal voltage) from 0.0025 V to 0.25 V on a logarithmic axis. One curve for each value of IC (collector bias current): 0.001 A, 0.0005 A, 0.002 A. Other inputs as in the worked example: beta = 100.0, RC = 5000.0 ohm, RL = 10000.0 ohm, RE1 = 0.0 ohm, RB = 20000.0 ohm, Rsig = 1000.0 ohm. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, VT = 0.025 V, Av = -133.333.0.010.1-2000-10000-133.333IC = 0.001 A (example)IC = 0.0005 AIC = 0.002 AVT (thermal voltage [V]Av), voltage gain base to output
Av (voltage gain base to output) against VT (thermal voltage) from 0.0025 V to 0.25 V on a logarithmic axis. One curve for each value of IC (collector bias current): 0.001 A, 0.0005 A, 0.002 A. Other inputs as in the worked example: beta = 100.0, RC = 5000.0 ohm, RL = 10000.0 ohm, RE1 = 0.0 ohm, RB = 20000.0 ohm, Rsig = 1000.0 ohm. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, VT = 0.025 V, Av = -133.333.
electronics_engineering_ai999x.solve('elx_common_emitter_amplifier', IC=0.001, beta=100.0, VT=0.025, RC=5000.0, RL=10000.0, RE1=0.0, RB=20000.0, Rsig=1000.0)
# -> gm = 0.04 S, r_pi = 2500 ohm, Av = -133.333, Rin = 2222.22 ohm, Rout = 5000 ohm, Gv = -91.954   (SOLVED)
electronics_engineering_ai999x.solve('elx_common_emitter_amplifier', IC=0.002, beta=150.0, VT=0.025, RC=3300.0, RL=4700.0, RE1=220.0, RB=30000.0, Rsig=600.0)
# -> gm = 0.08 S, r_pi = 1875 ohm, Av = -8.28644, Rin = 16174.1 ohm, Rout = 3300 ohm, Gv = -7.99003   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Common-emitter amplifier: IC = 1 mA, beta = 100, VT = 25 mV, RC = 5000 ohm, RL = 10000 ohm, RE1 = 0 ohm, RB = 20000 ohm, Rsig = 1000 ohmSOLVEDgm = 0.04 S, r_pi = 2500 ohm, Av = -133.333, Rin = 2222.22 ohm, Rout = 5000 ohm, Gv = -91.954
Common-emitter amplifier: IC = 2 mA, beta = 150, VT = 25 mV, RC = 3300 ohm, RL = 4700 ohm, RE1 = 220 ohm, RB = 30000 ohm, Rsig = 600 ohmSOLVEDgm = 0.08 S, r_pi = 1875 ohm, Av = -8.28644, Rin = 16174.1 ohm, Rout = 3300 ohm, Gv = -7.99003
Common-emitter amplifier: beta = 100, VT = 25 mV, RC = 5000 ohm, RL = 10000 ohm, RE1 = 0 ohm, RB = 20000 ohm, Rsig = 1000 ohmNEEDS_INPUTelx_common_emitter_amplifier needs IC (collector bias current). Example: solve('elx_common_emitter_amplifier', IC='0.001
Common-emitter amplifier: IC = 1 mA, beta = 100, VT = 25 mV, RC = 5000 ohm, RL = 10000 ohm, RE1 = 0 ohm, RB = 20000 ohm, Rsig = 1000 ohm, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Common-collector (emitter-follower) amplifier, elx_common_collector_amplifier

The voltage gain, input resistance and output resistance of an emitter follower, including the source resistance reflected into the emitter (hybrid-pi model, r_o neglected).

\[A_v = \frac{(\beta+1)R_E'}{r_\pi + (\beta+1)R_E'},\quad R_{out} = R_E\parallel\frac{r_\pi + R_{sig}\parallel R_B}{\beta+1}\]
inputmeaningcondition
ICcollector bias current
betacurrent gain
VTthermal voltage
REemitter resistor
RLload resistor
RBbias resistance at the base
Rsigsource resistance
outputmeaning
Avvoltage gain base to output
Rininput resistance
Routoutput resistance
Gvoverall gain from the source
Common-collector (emitter-follower) amplifier: voltage gain base to output against collector bias currentAv (voltage gain base to output) against IC (collector bias current) from 0.0005 A to 0.05 A on a logarithmic axis. One curve for each value of VT (thermal voltage): 0.025 V, 0.0125 V, 0.05 V. Other inputs as in the worked example: beta = 100.0, RE = 1000.0 ohm, RL = 1000.0 ohm, RB = 100000.0 ohm, Rsig = 10000.0 ohm. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, IC = 0.005 A, Av = 0.990196.0.0010.010.850.90.9510.990196VT = 0.025 V (example)VT = 0.0125 VVT = 0.05 VIC (collector bias current [A]Av), voltage gain base to output
Av (voltage gain base to output) against IC (collector bias current) from 0.0005 A to 0.05 A on a logarithmic axis. One curve for each value of VT (thermal voltage): 0.025 V, 0.0125 V, 0.05 V. Other inputs as in the worked example: beta = 100.0, RE = 1000.0 ohm, RL = 1000.0 ohm, RB = 100000.0 ohm, Rsig = 10000.0 ohm. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, IC = 0.005 A, Av = 0.990196.
electronics_engineering_ai999x.solve('elx_common_collector_amplifier', IC=0.005, beta=100.0, VT=0.025, RE=1000.0, RL=1000.0, RB=100000.0, Rsig=10000.0)
# -> Av = 0.990196, Rin = 33774.8 ohm, Rout = 86.7242 ohm, Gv = 0.763994   (SOLVED)
electronics_engineering_ai999x.solve('elx_common_collector_amplifier', IC=0.001, beta=200.0, VT=0.026, RE=4700.0, RL=2000.0, RB=47000.0, Rsig=5000.0)
# -> Av = 0.981894, Rin = 40390.2 ohm, Rout = 47.862 ohm, Gv = 0.873733   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Common-collector amplifier: IC = 5 mA, beta = 100, VT = 25 mV, RE = 1000 ohm, RL = 1000 ohm, RB = 100000 ohm, Rsig = 10000 ohmSOLVEDAv = 0.990196, Rin = 33774.8 ohm, Rout = 86.7242 ohm, Gv = 0.763994
Common-collector amplifier: IC = 1 mA, beta = 200, VT = 26 mV, RE = 4700 ohm, RL = 2000 ohm, RB = 47000 ohm, Rsig = 5000 ohmSOLVEDAv = 0.981894, Rin = 40390.2 ohm, Rout = 47.862 ohm, Gv = 0.873733
Common-collector amplifier: beta = 100, VT = 25 mV, RE = 1000 ohm, RL = 1000 ohm, RB = 100000 ohm, Rsig = 10000 ohmNEEDS_INPUTelx_common_collector_amplifier needs IC (collector bias current). Example: solve('elx_common_collector_amplifier', IC='0
Common-collector amplifier: IC = 5 mA, beta = 100, VT = 25 mV, RE = 1000 ohm, RL = 1000 ohm, RB = 100000 ohm, Rsig = 10000 ohm, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Common-base amplifier, elx_common_base_amplifier

The voltage gain (emitter to collector and source to load), the low input resistance and the output resistance of a common-base stage (hybrid-pi model, r_o neglected).

\[A_v = g_m(R_C\parallel R_L),\quad R_{in} = R_E\parallel r_e\]
inputmeaningcondition
ICcollector bias current
betacurrent gain
VTthermal voltage
RCcollector resistor
RLload resistor
REemitter bias resistor
Rsigsource resistance
outputmeaning
Avvoltage gain emitter to output
Rininput resistance (RE || r_e)
Routoutput resistance (RC)
Gvoverall gain from the source
Common-base amplifier: voltage gain emitter to output against thermal voltageAv (voltage gain emitter to output) against VT (thermal voltage) from 0.0125 V to 0.0375 V. One curve for each value of IC (collector bias current): 0.001 A, 0.0005 A, 0.002 A. Other inputs as in the worked example: beta = 100.0, RC = 5000.0 ohm, RL = 5000.0 ohm, RE = 10000.0 ohm, Rsig = 50.0 ohm. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, VT = 0.025 V, Av = 100.0.020.03100200300400100IC = 0.001 A (example)IC = 0.0005 AIC = 0.002 AVT (thermal voltage [V]Av), voltage gain emitter to output
Av (voltage gain emitter to output) against VT (thermal voltage) from 0.0125 V to 0.0375 V. One curve for each value of IC (collector bias current): 0.001 A, 0.0005 A, 0.002 A. Other inputs as in the worked example: beta = 100.0, RC = 5000.0 ohm, RL = 5000.0 ohm, RE = 10000.0 ohm, Rsig = 50.0 ohm. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, VT = 0.025 V, Av = 100.
electronics_engineering_ai999x.solve('elx_common_base_amplifier', IC=0.001, beta=100.0, VT=0.025, RC=5000.0, RL=5000.0, RE=10000.0, Rsig=50.0)
# -> Av = 100, Rin = 24.6914 ohm, Rout = 5000 ohm, Gv = 33.0579   (SOLVED)
electronics_engineering_ai999x.solve('elx_common_base_amplifier', IC=0.0005, beta=120.0, VT=0.026, RC=10000.0, RL=20000.0, RE=4700.0, Rsig=100.0)
# -> Av = 128.205, Rin = 51.0105 ohm, Rout = 10000 ohm, Gv = 43.307   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Common-base amplifier: IC = 1 mA, beta = 100, VT = 25 mV, RC = 5000 ohm, RL = 5000 ohm, RE = 10000 ohm, Rsig = 50 ohmSOLVEDAv = 100, Rin = 24.6914 ohm, Rout = 5000 ohm, Gv = 33.0579
Common-base amplifier: IC = 0.5 mA, beta = 120, VT = 26 mV, RC = 10000 ohm, RL = 20000 ohm, RE = 4700 ohm, Rsig = 100 ohmSOLVEDAv = 128.205, Rin = 51.0105 ohm, Rout = 10000 ohm, Gv = 43.307
Common-base amplifier: beta = 100, VT = 25 mV, RC = 5000 ohm, RL = 5000 ohm, RE = 10000 ohm, Rsig = 50 ohmNEEDS_INPUTelx_common_base_amplifier needs IC (collector bias current). Example: solve('elx_common_base_amplifier', IC='0.001 A', b
Common-base amplifier: IC = 1 mA, beta = 100, VT = 25 mV, RC = 5000 ohm, RL = 5000 ohm, RE = 10000 ohm, Rsig = 50 ohm, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

BJT beta cutoff and transition frequency fT, elx_transition_frequency

The beta cutoff frequency f_beta and the unity-current-gain (transition) frequency fT = gm/(2 pi (Cpi + Cmu)) of a bipolar transistor from its hybrid-pi capacitances.

\[f_T = \frac{g_m}{2\pi(C_\pi + C_\mu)},\quad f_\beta = \frac{f_T}{\beta}\]
inputmeaningcondition
gmtransconductance
betalow-frequency current gain
Cpibase-emitter capacitance
Cmubase-collector capacitance
outputmeaning
r_pi$r_pi = \beta/gm$
f_betabeta cutoff frequency
f_Ttransition frequency
BJT beta cutoff and transition frequency fT: transition frequency against base-emitter capacitancef_T (transition frequency) against Cpi (base-emitter capacitance) from 1.0000e-12 F to 1.0000e-10 F on a logarithmic axis. One curve for each value of gm (transconductance): 0.04 S, 0.02 S, 0.08 S. Other inputs as in the worked example: beta = 100.0, Cmu = 2e-12 F. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Cpi = 1.0000e-11 F, f_T = 5.3052e+08 Hz.1.00e-121.00e-111.00e-1001.00e92.00e93.00e94.00e95.3052e+08 Hzgm = 0.04 S (example)gm = 0.02 Sgm = 0.08 SCpi (base-emitter capacitance [F]f_T), transition frequency [Hz]
f_T (transition frequency) against Cpi (base-emitter capacitance) from 1.0000e-12 F to 1.0000e-10 F on a logarithmic axis. One curve for each value of gm (transconductance): 0.04 S, 0.02 S, 0.08 S. Other inputs as in the worked example: beta = 100.0, Cmu = 2e-12 F. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Cpi = 1.0000e-11 F, f_T = 5.3052e+08 Hz.
electronics_engineering_ai999x.solve('elx_transition_frequency', gm=0.04, beta=100.0, Cpi=1e-11, Cmu=2e-12)
# -> r_pi = 2500 ohm, f_beta = 5.30516e+06 Hz, f_T = 5.30516e+08 Hz   (SOLVED)
electronics_engineering_ai999x.solve('elx_transition_frequency', gm=0.1, beta=150.0, Cpi=2e-11, Cmu=1e-12)
# -> r_pi = 1500 ohm, f_beta = 5.05254e+06 Hz, f_T = 7.57881e+08 Hz   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Transition frequency: gm = 40 mS, beta = 100, Cpi = 10 pF, Cmu = 2 pFSOLVEDr_pi = 2500 ohm, f_beta = 5.30516e+06 Hz, f_T = 5.30516e+08 Hz
Transition frequency: gm = 100 mS, beta = 150, Cpi = 20 pF, Cmu = 1 pFSOLVEDr_pi = 1500 ohm, f_beta = 5.05254e+06 Hz, f_T = 7.57881e+08 Hz
Transition frequency: beta = 100, Cpi = 10 pF, Cmu = 2 pFNEEDS_INPUTelx_transition_frequency needs gm (transconductance). Example: solve('elx_transition_frequency', gm='0.04 S', beta=100,
Transition frequency: gm = 40 mS, beta = 100, Cpi = 10 pF, Cmu = 2 pF, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Common-emitter high-frequency cutoff: Miller effect and open-circuit time constants, elx_miller_high_cutoff

The Miller capacitance, the upper -3 dB frequency of a common-emitter (or common-source) stage by the Miller approximation, and the open-circuit time-constant estimate that also counts the output side of Cmu.

\[C_M = C_\mu(1 + g_mR_L'),\quad \tau_{oc} = C_\pi R_\pi' + C_\mu\left(R_\pi' + R_L' + g_mR_\pi'R_L'\right)\]
inputmeaningcondition
gmtransconductance
r_pir_pi (use a very large value for a MOSFET)
Cpiinput capacitance Cpi (Cgs)
Cmufeedback capacitance Cmu (Cgd)
RLptotal load at the collector (RC || RL || r_o)
Rsigpsource resistance seen at the base (Rsig || RB)
outputmeaning
A_midgain across Cmu, -gm RL'
C_MMiller capacitance
R_pi_eqresistance seen by Cpi (r_pi || Rsig')
f_H_millerupper cutoff, Miller approximation
tau_ocsum of open-circuit time constants
f_H_octcupper cutoff, open-circuit time constants
Common-emitter high-frequency cutoff: Miller effect and open-circuit time constants: upper cutoff, open-cir…f_H_octc (upper cutoff, open-circuit time constants) against r_pi (r_pi (use a very large value for a MOSFET)) from 250 ohm to 25000 ohm on a logarithmic axis. One curve for each value of Cmu (feedback capacitance Cmu (Cgd)): 2.0000e-12 F, 1.0000e-12 F, 4.0000e-12 F. Other inputs as in the worked example: gm = 0.04 S, Cpi = 1e-11 F, RLp = 2500.0 ohm, Rsigp = 1000.0 ohm. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, r_pi = 2500 ohm, f_H_octc = 1.01743e+06 Hz.10001000002.00e64.00e66.00e61.01743e+06 HzCmu = 2.0000e-12 F (example)Cmu = 1.0000e-12 FCmu = 4.0000e-12 Fr_pi (r_pi [ohm]f_H_octc), upper cutoff [Hz]
f_H_octc (upper cutoff, open-circuit time constants) against r_pi (r_pi (use a very large value for a MOSFET)) from 250 ohm to 25000 ohm on a logarithmic axis. One curve for each value of Cmu (feedback capacitance Cmu (Cgd)): 2.0000e-12 F, 1.0000e-12 F, 4.0000e-12 F. Other inputs as in the worked example: gm = 0.04 S, Cpi = 1e-11 F, RLp = 2500.0 ohm, Rsigp = 1000.0 ohm. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, r_pi = 2500 ohm, f_H_octc = 1.01743e+06 Hz.
electronics_engineering_ai999x.solve('elx_miller_high_cutoff', gm=0.04, r_pi=2500.0, Cpi=1e-11, Cmu=2e-12, RLp=2500.0, Rsigp=1000.0)
# -> A_mid = -100, C_M = 2.02e-10 F, R_pi_eq = 714.286 ohm, f_H_miller = 1.05102e+06 Hz, tau_oc = 1.56429e-07 s, f_H_octc = 1.01743e+06 Hz   (SOLVED)
electronics_engineering_ai999x.solve('elx_miller_high_cutoff', gm=0.1, r_pi=1500.0, Cpi=2e-11, Cmu=1e-12, RLp=1000.0, Rsigp=500.0)
# -> A_mid = -100, C_M = 1.01e-10 F, R_pi_eq = 375 ohm, f_H_miller = 3.50755e+06 Hz, tau_oc = 4.6375e-08 s, f_H_octc = 3.43191e+06 Hz   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Miller high-frequency cutoff: gm = 40 mS, r_pi = 2500 ohm, Cpi = 10 pF, Cmu = 2 pF, RLp = 2500 ohm, Rsigp = 1000 ohmSOLVEDA_mid = -100, C_M = 2.02e-10 F, R_pi_eq = 714.286 ohm, f_H_miller = 1.05102e+06 Hz, tau_oc = 1.56429e-07 s, f_H_octc = 1.01743e+06 Hz
Miller high-frequency cutoff: gm = 100 mS, r_pi = 1500 ohm, Cpi = 20 pF, Cmu = 1 pF, RLp = 1000 ohm, Rsigp = 500 ohmSOLVEDA_mid = -100, C_M = 1.01e-10 F, R_pi_eq = 375 ohm, f_H_miller = 3.50755e+06 Hz, tau_oc = 4.6375e-08 s, f_H_octc = 3.43191e+06 Hz
Miller high-frequency cutoff: r_pi = 2500 ohm, Cpi = 10 pF, Cmu = 2 pF, RLp = 2500 ohm, Rsigp = 1000 ohmNEEDS_INPUTelx_miller_high_cutoff needs gm (transconductance). Example: solve('elx_miller_high_cutoff', gm='0.04 S', r_pi='2500 ohm
Miller high-frequency cutoff: gm = 40 mS, r_pi = 2500 ohm, Cpi = 10 pF, Cmu = 2 pF, RLp = 2500 ohm, Rsigp = 1000 ohm, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Common-emitter low-frequency cutoff by short-circuit time constants, elx_low_frequency_cutoff

The resistance seen by each coupling and bypass capacitor of a common-emitter amplifier and the lower -3 dB frequency estimated as the sum of the short-circuit pole frequencies (r_o neglected).

\[f_L \approx \sum_i \frac{1}{2\pi R_iC_i}\]
inputmeaningcondition
Rsigsource resistance
RBbias resistance at the base (R1 || R2)
r_pir_pi
betacurrent gain
REemitter resistor (bypassed by CE)
RCcollector resistor
RLload resistor
C1input coupling capacitor
C2output coupling capacitor
CEemitter bypass capacitor
outputmeaning
R_C1resistance seen by C1
R_CEresistance seen by CE
R_C2resistance seen by C2
f_C1pole of C1
f_CEpole of CE
f_C2pole of C2
f_Lestimated lower cutoff
Common-emitter low-frequency cutoff by short-circuit time constants: estimated lower cutoff against emitter…f_L (estimated lower cutoff) against CE (emitter bypass capacitor) from 1.0000e-05 F to 0.001 F on a logarithmic axis. One curve for each value of beta (current gain): 100, 50, 200. Other inputs as in the worked example: Rsig = 1000.0 ohm, RB = 20000.0 ohm, r_pi = 2500.0 ohm, RE = 1000.0 ohm, RC = 5000.0 ohm, RL = 10000.0 ohm, C1 = 9.999999999999999e-06 F, C2 = 9.999999999999999e-06 F. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, CE = 1.0000e-04 F, f_L = 54.1529 Hz.1.00e-51.00e-40.0010250500750100054.1529 Hzbeta = 100 (example)beta = 50beta = 200CE (emitter bypass capacitor [F]f_L), estimated lower cutoff [Hz]
f_L (estimated lower cutoff) against CE (emitter bypass capacitor) from 1.0000e-05 F to 0.001 F on a logarithmic axis. One curve for each value of beta (current gain): 100, 50, 200. Other inputs as in the worked example: Rsig = 1000.0 ohm, RB = 20000.0 ohm, r_pi = 2500.0 ohm, RE = 1000.0 ohm, RC = 5000.0 ohm, RL = 10000.0 ohm, C1 = 9.999999999999999e-06 F, C2 = 9.999999999999999e-06 F. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, CE = 1.0000e-04 F, f_L = 54.1529 Hz.
electronics_engineering_ai999x.solve('elx_low_frequency_cutoff', Rsig=1000.0, RB=20000.0, r_pi=2500.0, beta=100.0, RE=1000.0, RC=5000.0, RL=10000.0, C1=1e-05, C2=1e-05, CE=0.0001)
# -> R_C1 = 3222.22 ohm, R_CE = 33.0522 ohm, R_C2 = 15000 ohm, f_C1 = 4.93929 Hz, f_CE = 48.1526 Hz, f_C2 = 1.06103 Hz, f_L = 54.1529 Hz   (SOLVED)
electronics_engineering_ai999x.solve('elx_low_frequency_cutoff', Rsig=600.0, RB=30000.0, r_pi=1875.0, beta=150.0, RE=470.0, RC=3300.0, RL=4700.0, C1=4.7e-06, C2=1e-06, CE=0.00022)
# -> R_C1 = 2364.71 ohm, R_CE = 15.7656 ohm, R_C2 = 8000 ohm, f_C1 = 14.3201 Hz, f_CE = 45.8867 Hz, f_C2 = 19.8944 Hz, f_L = 80.1011 Hz   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Low-frequency cutoff: Rsig = 1000 ohm, RB = 20000 ohm, r_pi = 2500 ohm, beta = 100, RE = 1000 ohm, RC = 5000 ohm, RL = 10000 ohm, C1 = 10 uF, C2 = 10 uF, CE = 100 uFSOLVEDR_C1 = 3222.22 ohm, R_CE = 33.0522 ohm, R_C2 = 15000 ohm, f_C1 = 4.93929 Hz, f_CE = 48.1526 Hz, f_C2 = 1.06103 Hz, f_L = 54.1529 Hz
Low-frequency cutoff: Rsig = 600 ohm, RB = 30000 ohm, r_pi = 1875 ohm, beta = 150, RE = 470 ohm, RC = 3300 ohm, RL = 4700 ohm, C1 = 4.7 uF, C2 = 1 uF, CE = 220 uFSOLVEDR_C1 = 2364.71 ohm, R_CE = 15.7656 ohm, R_C2 = 8000 ohm, f_C1 = 14.3201 Hz, f_CE = 45.8867 Hz, f_C2 = 19.8944 Hz, f_L = 80.1011 Hz
Low-frequency cutoff: RB = 20000 ohm, r_pi = 2500 ohm, beta = 100, RE = 1000 ohm, RC = 5000 ohm, RL = 10000 ohm, C1 = 10 uF, C2 = 10 uF, CE = 100 uFNEEDS_INPUTelx_low_frequency_cutoff needs Rsig (source resistance). Example: solve('elx_low_frequency_cutoff', Rsig='1000 ohm', RB=
Low-frequency cutoff: Rsig = 1000 ohm, RB = 20000 ohm, r_pi = 2500 ohm, beta = 100, RE = 1000 ohm, RC = 5000 ohm, RL = 10000 ohm, C1 = 10 uF, C2 = 10 uF, CE = 100 uF, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

BJT current mirror with finite beta, elx_current_mirror

The reference current and the output current of a basic two-transistor current mirror with a resistor to the supply, including the base-current error Iout = Iref $\beta/(\beta + 2)$.

\[I_{out} = \frac{\beta}{\beta+2}I_{ref}\]
inputmeaningcondition
VCCsupply voltage
Rreference resistor
VBEbase-emitter voltage
betacurrent gain of each (matched) transistor
outputmeaning
Irefcurrent in the reference resistor
Ioutoutput (mirrored) current
ratioIout/Iref
BJT current mirror with finite beta: output (mirrored) current against reference resistorIout (output (mirrored) current) against R (reference resistor) from 4650 ohm to 13950 ohm. One curve for each value of VCC (supply voltage): 10 V, 5 V, 20 V. Other inputs as in the worked example: VBE = 0.7 V, beta = 100.0. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R = 9300 ohm, Iout = 0.000980392 A.5000750010000125000.0010.0020.0030.0040.000980392 AVCC = 10 V (example)VCC = 5 VVCC = 20 VR (reference resistor [ohm]Iout), output (mirrored) current [A]
Iout (output (mirrored) current) against R (reference resistor) from 4650 ohm to 13950 ohm. One curve for each value of VCC (supply voltage): 10 V, 5 V, 20 V. Other inputs as in the worked example: VBE = 0.7 V, beta = 100.0. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R = 9300 ohm, Iout = 0.000980392 A.
electronics_engineering_ai999x.solve('elx_current_mirror', VCC=10.0, R=9300.0, VBE=0.7, beta=100.0)
# -> Iref = 0.001 A, Iout = 0.000980392 A, ratio = 0.980392   (SOLVED)
electronics_engineering_ai999x.solve('elx_current_mirror', VCC=5.0, R=4300.0, VBE=0.7, beta=50.0)
# -> Iref = 0.001 A, Iout = 0.000961538 A, ratio = 0.961538   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Current mirror: VCC = 10 V, R = 9300 ohm, VBE = 0.7 V, beta = 100SOLVEDIref = 0.001 A, Iout = 0.000980392 A, ratio = 0.980392
Current mirror: VCC = 5 V, R = 4300 ohm, VBE = 0.7 V, beta = 50SOLVEDIref = 0.001 A, Iout = 0.000961538 A, ratio = 0.961538
Current mirror: R = 9300 ohm, VBE = 0.7 V, beta = 100NEEDS_INPUTelx_current_mirror needs VCC (supply voltage). Example: solve('elx_current_mirror', VCC='10 V', R='9300 ohm', VBE='0.7 V
Current mirror: VCC = 10 V, R = 9300 ohm, VBE = 0.7 V, beta = 100, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Wilson current mirror output current, elx_wilson_current_mirror

The output current of a three-transistor Wilson current mirror and its small base-current error, 2/(beta^2 + 2 beta + 2).

\[I_{out} = I_{ref}\left(1 - \frac{2}{\beta^2 + 2\beta + 2}\right)\]
inputmeaningcondition
Irefreference current
betacurrent gain of each matched transistor
outputmeaning
Ioutoutput current
ratioIout/Iref
errorrelative error 1 - Iout/Iref
Wilson current mirror output current: output current against current gain of each matched transistorIout (output current) against beta (current gain of each matched transistor) from 10 to 1000 on a logarithmic axis. One curve for each value of Iref (reference current): 0.001 A, 0.0005 A, 0.002 A. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, beta = 100, Iout = 0.000999804 A.1010010005.00e-40.0010.00150.0020.000999804 AIref = 0.001 A (example)Iref = 0.0005 AIref = 0.002 AbetaIout, output current [A]
Iout (output current) against beta (current gain of each matched transistor) from 10 to 1000 on a logarithmic axis. One curve for each value of Iref (reference current): 0.001 A, 0.0005 A, 0.002 A. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, beta = 100, Iout = 0.000999804 A.
Wilson current mirror output current: output current over reference current and current gain of each matche…Iout (output current) over Iref (reference current) from 0.0005 A to 0.0015 A and beta (current gain of each matched transistor) from 10 to 1000 (logarithmic vertical axis): each of the 21 × 15 cells is one run of electronics-engineering-ai999x, shaded by its value (light 0.000491803 A to dark 0.0015 A); iso-lines at Iout = 6.00e-4, 8.00e-4, 0.001, 0.0012, 0.0014 A. Marked: the worked example, Iref = 0.001 A, beta = 100, Iout = 0.000999804 A.5.00e-47.50e-40.0010.001250.00151010010006.00e-48.00e-40.0010.00120.00140.000999804 A0.00154.92e-4IoutIref, reference current [A]beta
Iout (output current) over Iref (reference current) from 0.0005 A to 0.0015 A and beta (current gain of each matched transistor) from 10 to 1000 (logarithmic vertical axis): each of the 21 × 15 cells is one run of electronics-engineering-ai999x, shaded by its value (light 0.000491803 A to dark 0.0015 A); iso-lines at Iout = 6.00e-4, 8.00e-4, 0.001, 0.0012, 0.0014 A. Marked: the worked example, Iref = 0.001 A, beta = 100, Iout = 0.000999804 A.
electronics_engineering_ai999x.solve('elx_wilson_current_mirror', Iref=0.001, beta=100.0)
# -> Iout = 0.000999804 A, ratio = 0.999804, error = 0.00019604   (SOLVED)
electronics_engineering_ai999x.solve('elx_wilson_current_mirror', Iref=0.0002, beta=20.0)
# -> Iout = 0.000199095 A, ratio = 0.995475, error = 0.00452489   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Wilson current mirror: Iref = 1 mA, beta = 100SOLVEDIout = 0.000999804 A, ratio = 0.999804, error = 0.00019604
Wilson current mirror: Iref = 0.2 mA, beta = 20SOLVEDIout = 0.000199095 A, ratio = 0.995475, error = 0.00452489
Wilson current mirror: beta = 100NEEDS_INPUTelx_wilson_current_mirror needs Iref (reference current). Example: solve('elx_wilson_current_mirror', Iref='0.001 A', be
Wilson current mirror: Iref = 1 mA, beta = 100, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

BJT differential pair: differential and common-mode gain, CMRR, elx_differential_pair

The differential gain (differential and single-ended output), the common-mode gain and the common-mode rejection ratio of a resistively loaded BJT differential pair with a tail current source of finite resistance.

\[A_{cm} = -\frac{g_mR_C}{1 + 2R_{EE}(\beta+1)/r_\pi},\quad \text{CMRR} = \frac{1 + 2R_{EE}(\beta+1)/r_\pi}{2}\]
inputmeaningcondition
I_tailtail (bias) current
betacurrent gain
VTthermal voltage
RCcollector resistor of each side
REEoutput resistance of the tail current source
outputmeaning
ICcollector current of each transistor
gmtransconductance of each
Ad_diffdifferential gain, differential output
Ad_sedifferential gain, single-ended output
Acmcommon-mode gain, single-ended output
CMRR|Ad_se/Acm|
CMRR_dBCMRR in dB
BJT differential pair: differential and common-mode gain, CMRR: |Ad_se/Acm| against thermal voltageCMRR (|Ad_se/Acm|) against VT (thermal voltage) from 0.0125 V to 0.0375 V. One curve for each value of I_tail (tail (bias) current): 0.001 A, 0.0005 A, 0.002 A. Other inputs as in the worked example: beta = 100.0, RC = 10000.0 ohm, REE = 100000.0 ohm. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, VT = 0.025 V, CMRR = 2000.5.0.020.0320004000600080002000.5I_tail = 0.001 A (example)I_tail = 0.0005 AI_tail = 0.002 AVT (thermal voltage [V]CMRR), |Ad_se/Acm|
CMRR (|Ad_se/Acm|) against VT (thermal voltage) from 0.0125 V to 0.0375 V. One curve for each value of I_tail (tail (bias) current): 0.001 A, 0.0005 A, 0.002 A. Other inputs as in the worked example: beta = 100.0, RC = 10000.0 ohm, REE = 100000.0 ohm. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, VT = 0.025 V, CMRR = 2000.5.
electronics_engineering_ai999x.solve('elx_differential_pair', I_tail=0.001, beta=100.0, VT=0.025, RC=10000.0, REE=100000.0)
# -> IC = 0.00049505 A, gm = 0.019802 S, Ad_diff = -198.02, Ad_se = -99.0099, Acm = -0.0494926, CMRR = 2000.5, CMRR_dB = 66.0228   (SOLVED)
electronics_engineering_ai999x.solve('elx_differential_pair', I_tail=0.002, beta=200.0, VT=0.026, RC=5000.0, REE=50000.0)
# -> IC = 0.000995025 A, gm = 0.0382702 S, Ad_diff = -191.351, Ad_se = -95.6755, Acm = -0.0497383, CMRR = 1923.58, CMRR_dB = 65.6822   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Differential pair: I_tail = 1 mA, beta = 100, VT = 25 mV, RC = 10000 ohm, REE = 100000 ohmSOLVEDIC = 0.00049505 A, gm = 0.019802 S, Ad_diff = -198.02, Ad_se = -99.0099, Acm = -0.0494926, CMRR = 2000.5, CMRR_dB = 66.0228
Differential pair: I_tail = 2 mA, beta = 200, VT = 26 mV, RC = 5000 ohm, REE = 50000 ohmSOLVEDIC = 0.000995025 A, gm = 0.0382702 S, Ad_diff = -191.351, Ad_se = -95.6755, Acm = -0.0497383, CMRR = 1923.58, CMRR_dB = 65.6822
Differential pair: beta = 100, VT = 25 mV, RC = 10000 ohm, REE = 100000 ohmNEEDS_INPUTelx_differential_pair needs I_tail (tail (bias) current). Example: solve('elx_differential_pair', I_tail='0.001 A', beta
Differential pair: I_tail = 1 mA, beta = 100, VT = 25 mV, RC = 10000 ohm, REE = 100000 ohm, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

BJT cascode: output resistance, transconductance and gain, elx_bjt_cascode

The output resistance, the short-circuit transconductance and the voltage gain into a load of a cascode (common emitter driving common base) of two identical transistors at the same bias current.

\[R_{out} = r_o + (1 + g_mr_o)(r_o\parallel r_\pi),\quad A_v = -G_m(R_{out}\parallel R_L)\]
inputmeaningcondition
ICbias current of both transistors
betacurrent gain
VTthermal voltage
VAEarly voltage
RLload resistance
outputmeaning
gmtransconductance of each transistor
r_ooutput resistance of each
Routoutput resistance of the cascode
Gmshort-circuit transconductance
Avvoltage gain into RL
BJT cascode: output resistance, transconductance and gain: output resistance of the cascode against bias cu…Rout (output resistance of the cascode) against IC (bias current of both transistors) from 0.0005 A to 0.0015 A. One curve for each value of VA (Early voltage): 100 V, 50 V, 200 V. Other inputs as in the worked example: beta = 100.0, VT = 0.025 V, RL = 1000000.0 ohm. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, IC = 0.001 A, Rout = 9.85854e+06 ohm.5.00e-47.50e-40.0010.001250.00151.00e72.00e73.00e74.00e79.85854e+06 ohmVA = 100 V (example)VA = 50 VVA = 200 VIC, bias current of both transistors [A]Rout [ohm]
Rout (output resistance of the cascode) against IC (bias current of both transistors) from 0.0005 A to 0.0015 A. One curve for each value of VA (Early voltage): 100 V, 50 V, 200 V. Other inputs as in the worked example: beta = 100.0, VT = 0.025 V, RL = 1000000.0 ohm. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, IC = 0.001 A, Rout = 9.85854e+06 ohm.
electronics_engineering_ai999x.solve('elx_bjt_cascode', IC=0.001, beta=100.0, VT=0.025, VA=100.0, RL=1000000.0)
# -> gm = 0.04 S, r_o = 100000 ohm, Rout = 9.85854e+06 ohm, Gm = 0.0395943 S, Av = -35947.9   (SOLVED)
electronics_engineering_ai999x.solve('elx_bjt_cascode', IC=0.0001, beta=200.0, VT=0.026, VA=50.0, RL=10000000.0)
# -> gm = 0.00384615 S, r_o = 500000 ohm, Rout = 9.11268e+07 ohm, Gm = 0.00382505 S, Av = -34468.1   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
BJT cascode: IC = 1 mA, beta = 100, VT = 25 mV, VA = 100 V, RL = 1000000 ohmSOLVEDgm = 0.04 S, r_o = 100000 ohm, Rout = 9.85854e+06 ohm, Gm = 0.0395943 S, Av = -35947.9
BJT cascode: IC = 0.1 mA, beta = 200, VT = 26 mV, VA = 50 V, RL = 10000000 ohmSOLVEDgm = 0.00384615 S, r_o = 500000 ohm, Rout = 9.11268e+07 ohm, Gm = 0.00382505 S, Av = -34468.1
BJT cascode: beta = 100, VT = 25 mV, VA = 100 V, RL = 1000000 ohmNEEDS_INPUTelx_bjt_cascode needs IC (bias current of both transistors). Example: solve('elx_bjt_cascode', IC='0.001 A', beta=100, V
BJT cascode: IC = 1 mA, beta = 100, VT = 25 mV, VA = 100 V, RL = 1000000 ohm, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

MOSFET drain current (cutoff, triode, saturation), elx_mosfet_drain_current

The operating region and drain current of an enhancement NMOS transistor by the square law: cutoff, triode or saturation with optional channel-length modulation (use magnitudes for PMOS).

\[I_D = \begin{cases} k_n\left(V_{OV}V_{DS} - \tfrac{1}{2}V_{DS}^2\right) & V_{DS} < V_{OV}\\ \tfrac{1}{2}k_nV_{OV}^2(1+\lambda V_{DS}) & V_{DS}\ge V_{OV}\end{cases}\]
inputmeaningcondition
knprocess transconductance times aspect ratio, mu Cox W/L
Vtthreshold voltage
VGSgate-source voltage
VDSdrain-source voltage
lamchannel-length modulation lambda (default 0)
outputmeaning
regioncutoff, triode or saturation
IDdrain current
VOVoverdrive VGS - Vt
VDS_satsaturation voltage
MOSFET drain current (cutoff, triode, saturation): where the verdict changes (region)cutoff, triode or saturation (region) over VGS (gate-source voltage) from 0.3 V to 30 V and Vt (threshold voltage) from 0.1 V to 10 V (logarithmic axes): each of the 31 × 21 cells is one run of electronics-engineering-ai999x, coloured by the verdict it returned, cutoff: 192 cells, saturation: 246 cells, triode: 213 cells. Other inputs as in the worked example: kn = 0.002 A/V^2, VDS = 5.0 V. Marked: the worked example, VGS = 3 V, Vt = 1 V → saturation.1100.1110saturationregion: cutoff (192)region: saturation (246)region: triode (213)VGS (gate-source voltage [V]Vt), threshold voltage [V]
cutoff, triode or saturation (region) over VGS (gate-source voltage) from 0.3 V to 30 V and Vt (threshold voltage) from 0.1 V to 10 V (logarithmic axes): each of the 31 × 21 cells is one run of electronics-engineering-ai999x, coloured by the verdict it returned, cutoff: 192 cells, saturation: 246 cells, triode: 213 cells. Other inputs as in the worked example: kn = 0.002 A/V^2, VDS = 5.0 V. Marked: the worked example, VGS = 3 V, Vt = 1 V → saturation.
MOSFET drain current (cutoff, triode, saturation): drain current against drain-source voltageID (drain current) against VDS (drain-source voltage) from 0.5 V to 50 V on a logarithmic axis. One curve for each value of VGS (gate-source voltage): 3 V, 1.5 V, 6 V. Other inputs as in the worked example: kn = 0.002 A/V^2, Vt = 1.0 V. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, VDS = 5 V, ID = 0.004 A.11000.010.020.004 AVGS = 3 V (example)VGS = 1.5 VVGS = 6 VVDS (drain-source voltage [V]ID), drain current [A]
ID (drain current) against VDS (drain-source voltage) from 0.5 V to 50 V on a logarithmic axis. One curve for each value of VGS (gate-source voltage): 3 V, 1.5 V, 6 V. Other inputs as in the worked example: kn = 0.002 A/V^2, Vt = 1.0 V. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, VDS = 5 V, ID = 0.004 A.
electronics_engineering_ai999x.solve('elx_mosfet_drain_current', kn=0.002, Vt=1.0, VGS=3.0, VDS=5.0)
# -> region = saturation, ID = 0.004 A, VOV = 2 V, VDS_sat = 2 V   (SOLVED)
electronics_engineering_ai999x.solve('elx_mosfet_drain_current', kn=0.001, Vt=0.7, VGS=2.0, VDS=0.5, lam=0.02)
# -> region = triode, ID = 0.000525 A, VOV = 1.3 V, VDS_sat = 1.3 V   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
MOSFET drain current: kn = 2 mA/V^2, Vt = 1 V, VGS = 3 V, VDS = 5 VSOLVEDregion = saturation, ID = 0.004 A, VOV = 2 V, VDS_sat = 2 V
MOSFET drain current: kn = 1 mA/V^2, Vt = 0.7 V, VGS = 2 V, VDS = 0.5 V, lam = 0.02 1/VSOLVEDregion = triode, ID = 0.000525 A, VOV = 1.3 V, VDS_sat = 1.3 V
MOSFET drain current: Vt = 1 V, VGS = 3 V, VDS = 5 VNEEDS_INPUTelx_mosfet_drain_current needs kn (process transconductance times aspect ratio, mu Cox W/L). Example: solve('elx_mosfet_
MOSFET drain current: kn = 2 mA/V^2, Vt = 1 V, VGS = 3 V, VDS = 5 V, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

MOSFET small-signal gm, ro and intrinsic gain, elx_mosfet_gm_ro

The overdrive voltage, gate-source voltage, transconductance $gm = sqrt$(2 kn ID), output resistance ro = 1/(lambda ID) and intrinsic gain of a MOSFET in saturation at a drain current.

\[g_m = \sqrt{2k_nI_D} = \frac{2I_D}{V_{OV}},\quad r_o = \frac{1}{\lambda I_D}\]
inputmeaningcondition
knmu Cox W/L
IDdrain bias current
lamchannel-length modulation lambda
Vtthreshold voltage
outputmeaning
VOVoverdrive voltage
VGSgate-source voltage
gmtransconductance
r_ooutput resistance
A0intrinsic gain gm r_o
MOSFET small-signal gm, ro and intrinsic gain: transconductance against mu Cox W/Lgm (transconductance) against kn (mu Cox W/L) from 0.001 A/V^2 to 0.003 A/V^2. One curve for each value of ID (drain bias current): 0.001 A, 0.0005 A, 0.002 A. Other inputs as in the worked example: lam = 0.01 1/V, Vt = 0.7 V. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, kn = 0.002 A/V^2, gm = 0.002 S.0.0010.00150.0020.00250.0030.0010.0020.0030.002 SID = 0.001 A (example)ID = 0.0005 AID = 0.002 Akn (mu Cox W/L [A/V^2]gm), transconductance [S]
gm (transconductance) against kn (mu Cox W/L) from 0.001 A/V^2 to 0.003 A/V^2. One curve for each value of ID (drain bias current): 0.001 A, 0.0005 A, 0.002 A. Other inputs as in the worked example: lam = 0.01 1/V, Vt = 0.7 V. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, kn = 0.002 A/V^2, gm = 0.002 S.
electronics_engineering_ai999x.solve('elx_mosfet_gm_ro', kn=0.002, ID=0.001, lam=0.01, Vt=0.7)
# -> VOV = 1 V, VGS = 1.7 V, gm = 0.002 S, r_o = 100000 ohm, A0 = 200   (SOLVED)
electronics_engineering_ai999x.solve('elx_mosfet_gm_ro', kn=0.005, ID=0.0004, lam=0.05, Vt=0.5)
# -> VOV = 0.4 V, VGS = 0.9 V, gm = 0.002 S, r_o = 50000 ohm, A0 = 100   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
MOSFET small-signal parameters: kn = 2 mA/V^2, ID = 1 mA, lam = 0.01 1/V, Vt = 0.7 VSOLVEDVOV = 1 V, VGS = 1.7 V, gm = 0.002 S, r_o = 100000 ohm, A0 = 200
MOSFET small-signal parameters: kn = 5 mA/V^2, ID = 0.4 mA, lam = 0.05 1/V, Vt = 0.5 VSOLVEDVOV = 0.4 V, VGS = 0.9 V, gm = 0.002 S, r_o = 50000 ohm, A0 = 100
MOSFET small-signal parameters: ID = 1 mA, lam = 0.01 1/V, Vt = 0.7 VNEEDS_INPUTelx_mosfet_gm_ro needs kn (mu Cox W/L). Example: solve('elx_mosfet_gm_ro', kn='0.002 A/V^2', ID='0.001 A', lam='0.01 1/V
MOSFET small-signal parameters: kn = 2 mA/V^2, ID = 1 mA, lam = 0.01 1/V, Vt = 0.7 V, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

MOSFET voltage-divider bias with source resistor: Q-point, elx_mosfet_divider_bias

The Q-point (gate voltage, VGS, drain current, node voltages and VDS) of an NMOS stage with a gate divider and a source resistor, solving the square law and the gate loop (the physical root), with a saturation check.

\[V_{OV} = \frac{2(V_G - V_t)}{1 + \sqrt{1 + 2k_nR_S(V_G - V_t)}},\quad I_D = \tfrac{1}{2}k_nV_{OV}^2\]
inputmeaningcondition
VDDsupply voltage
R1upper gate resistor
R2lower gate resistor
RDdrain resistor
RSsource resistor (0 allowed)
knmu Cox W/L
Vtthreshold voltage
outputmeaning
VGgate voltage
VGSgate-source voltage
VOVoverdrive
IDdrain current
VSsource voltage
VDdrain voltage
VDSdrain-source voltage
MOSFET voltage-divider bias with source resistor: Q-point: drain current against source resistor (0 allowed)ID (drain current) against RS (source resistor (0 allowed)) from 500 ohm to 1500 ohm. One curve for each value of VDD (supply voltage): 15 V, 7.5 V, 30 V. Other inputs as in the worked example: R1 = 1000000.0 ohm, R2 = 500000.0 ohm, RD = 3300.0 ohm, kn = 0.002 A/V^2, Vt = 1.5 V. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, RS = 1000 ohm, ID = 0.00206351 A.50075010001250150000.0020.0040.0060.00206351 AVDD = 15 V (example)VDD = 7.5 VVDD = 30 VRS (source resistor (0 allowed) [ohm]ID), drain current [A]
ID (drain current) against RS (source resistor (0 allowed)) from 500 ohm to 1500 ohm. One curve for each value of VDD (supply voltage): 15 V, 7.5 V, 30 V. Other inputs as in the worked example: R1 = 1000000.0 ohm, R2 = 500000.0 ohm, RD = 3300.0 ohm, kn = 0.002 A/V^2, Vt = 1.5 V. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, RS = 1000 ohm, ID = 0.00206351 A.
electronics_engineering_ai999x.solve('elx_mosfet_divider_bias', VDD=15.0, R1=1000000.0, R2=500000.0, RD=3300.0, RS=1000.0, kn=0.002, Vt=1.5)
# -> VG = 5 V, VGS = 2.93649 V, VOV = 1.43649 V, ID = 0.00206351 A, VS = 2.06351 V, VD = 8.19042 V, VDS = 6.12691 V   (SOLVED)
electronics_engineering_ai999x.solve('elx_mosfet_divider_bias', VDD=12.0, R1=680000.0, R2=320000.0, RD=2200.0, RS=0.0, kn=0.001, Vt=1.0)
# -> VG = 3.84 V, VGS = 3.84 V, VOV = 2.84 V, ID = 0.0040328 A, VS = 0 V, VD = 3.12784 V, VDS = 3.12784 V   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
MOSFET divider bias: VDD = 15 V, R1 = 1000000 ohm, R2 = 500000 ohm, RD = 3300 ohm, RS = 1000 ohm, kn = 2 mA/V^2, Vt = 1.5 VSOLVEDVG = 5 V, VGS = 2.93649 V, VOV = 1.43649 V, ID = 0.00206351 A, VS = 2.06351 V, VD = 8.19042 V, VDS = 6.12691 V
MOSFET divider bias: VDD = 12 V, R1 = 680000 ohm, R2 = 320000 ohm, RD = 2200 ohm, RS = 0 ohm, kn = 1 mA/V^2, Vt = 1 VSOLVEDVG = 3.84 V, VGS = 3.84 V, VOV = 2.84 V, ID = 0.0040328 A, VS = 0 V, VD = 3.12784 V, VDS = 3.12784 V
MOSFET divider bias: R1 = 1000000 ohm, R2 = 500000 ohm, RD = 3300 ohm, RS = 1000 ohm, kn = 2 mA/V^2, Vt = 1.5 VNEEDS_INPUTelx_mosfet_divider_bias needs VDD (supply voltage). Example: solve('elx_mosfet_divider_bias', VDD='15 V', R1='1e+06 ohm'
MOSFET divider bias: VDD = 15 V, R1 = 1000000 ohm, R2 = 500000 ohm, RD = 3300 ohm, RS = 1000 ohm, kn = 2 mA/V^2, Vt = 1.5 V, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Common-source amplifier with source degeneration and ro, elx_common_source_amplifier

The voltage gain, input and output resistances and overall gain of a common-source stage, exact with the transistor's output resistance ro and an optional unbypassed source resistor.

\[A_v = -\frac{g_mr_oR_D'}{R_D' + r_o + R_S(1 + g_mr_o)}\]
inputmeaningcondition
gmtransconductance
rotransistor output resistance
RDdrain resistor
RLload resistor
RSunbypassed source resistance (0 if bypassed)
RGgate bias resistance
Rsigsource resistance
outputmeaning
Avvoltage gain gate to output
Rininput resistance
Routoutput resistance (excluding RL)
Gvoverall gain from the source
Common-source amplifier with source degeneration and ro: voltage gain gate to output against transistor out…Av (voltage gain gate to output) against ro (transistor output resistance) from 10000 ohm to 1e+06 ohm on a logarithmic axis. One curve for each value of gm (transconductance): 0.002 S, 0.001 S, 0.004 S. Other inputs as in the worked example: RD = 10000.0 ohm, RL = 10000.0 ohm, RS = 0.0 ohm, RG = 1000000.0 ohm, Rsig = 10000.0 ohm. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, ro = 100000 ohm, Av = -9.52381.100001.00e51.00e6-20-15-10-5-9.52381gm = 0.002 S (example)gm = 0.001 Sgm = 0.004 Sro (transistor output resistance [ohm]Av), voltage gain gate to output
Av (voltage gain gate to output) against ro (transistor output resistance) from 10000 ohm to 1e+06 ohm on a logarithmic axis. One curve for each value of gm (transconductance): 0.002 S, 0.001 S, 0.004 S. Other inputs as in the worked example: RD = 10000.0 ohm, RL = 10000.0 ohm, RS = 0.0 ohm, RG = 1000000.0 ohm, Rsig = 10000.0 ohm. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, ro = 100000 ohm, Av = -9.52381.
electronics_engineering_ai999x.solve('elx_common_source_amplifier', gm=0.002, ro=100000.0, RD=10000.0, RL=10000.0, RS=0.0, RG=1000000.0, Rsig=10000.0)
# -> Av = -9.52381, Rin = 1e+06 ohm, Rout = 9090.91 ohm, Gv = -9.42951   (SOLVED)
electronics_engineering_ai999x.solve('elx_common_source_amplifier', gm=0.004, ro=50000.0, RD=4700.0, RL=22000.0, RS=500.0, RG=2200000.0, Rsig=50000.0)
# -> Av = -5.01729, Rin = 2.2e+06 ohm, Rout = 4557.67 ohm, Gv = -4.90579   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Common-source amplifier: gm = 2 mS, ro = 100000 ohm, RD = 10000 ohm, RL = 10000 ohm, RS = 0 ohm, RG = 1000000 ohm, Rsig = 10000 ohmSOLVEDAv = -9.52381, Rin = 1e+06 ohm, Rout = 9090.91 ohm, Gv = -9.42951
Common-source amplifier: gm = 4 mS, ro = 50000 ohm, RD = 4700 ohm, RL = 22000 ohm, RS = 500 ohm, RG = 2200000 ohm, Rsig = 50000 ohmSOLVEDAv = -5.01729, Rin = 2.2e+06 ohm, Rout = 4557.67 ohm, Gv = -4.90579
Common-source amplifier: ro = 100000 ohm, RD = 10000 ohm, RL = 10000 ohm, RS = 0 ohm, RG = 1000000 ohm, Rsig = 10000 ohmNEEDS_INPUTelx_common_source_amplifier needs gm (transconductance). Example: solve('elx_common_source_amplifier', gm='0.002 S', ro=
Common-source amplifier: gm = 2 mS, ro = 100000 ohm, RD = 10000 ohm, RL = 10000 ohm, RS = 0 ohm, RG = 1000000 ohm, Rsig = 10000 ohm, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Source follower (common drain), elx_source_follower

The voltage gain, input resistance, output resistance and overall gain of a MOSFET source follower, including ro.

\[A_v = \frac{g_mR}{1 + g_mR},\quad R_{out} = R_S\parallel r_o\parallel\frac{1}{g_m}\]
inputmeaningcondition
gmtransconductance
rotransistor output resistance
RSsource resistor
RLload resistor
RGgate bias resistance
Rsigsource resistance
outputmeaning
Avvoltage gain gate to output
Rininput resistance
Routoutput resistance
Gvoverall gain
Source follower (common drain): voltage gain gate to output against transistor output resistanceAv (voltage gain gate to output) against ro (transistor output resistance) from 5000 ohm to 500000 ohm on a logarithmic axis. One curve for each value of gm (transconductance): 0.002 S, 0.001 S, 0.004 S. Other inputs as in the worked example: RS = 2000.0 ohm, RL = 2000.0 ohm, RG = 1000000.0 ohm, Rsig = 10000.0 ohm. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, ro = 50000 ohm, Av = 0.662252.100001.00e50.50.60.70.80.662252gm = 0.002 S (example)gm = 0.001 Sgm = 0.004 Sro (transistor output resistance [ohm]Av), voltage gain gate to output
Av (voltage gain gate to output) against ro (transistor output resistance) from 5000 ohm to 500000 ohm on a logarithmic axis. One curve for each value of gm (transconductance): 0.002 S, 0.001 S, 0.004 S. Other inputs as in the worked example: RS = 2000.0 ohm, RL = 2000.0 ohm, RG = 1000000.0 ohm, Rsig = 10000.0 ohm. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, ro = 50000 ohm, Av = 0.662252.
electronics_engineering_ai999x.solve('elx_source_follower', gm=0.002, ro=50000.0, RS=2000.0, RL=2000.0, RG=1000000.0, Rsig=10000.0)
# -> Av = 0.662252, Rin = 1e+06 ohm, Rout = 396.825 ohm, Gv = 0.655695   (SOLVED)
electronics_engineering_ai999x.solve('elx_source_follower', gm=0.005, ro=20000.0, RS=1000.0, RL=10000.0, RG=470000.0, Rsig=1000.0)
# -> Av = 0.813008, Rin = 470000 ohm, Rout = 165.289 ohm, Gv = 0.811282   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Source follower: gm = 2 mS, ro = 50000 ohm, RS = 2000 ohm, RL = 2000 ohm, RG = 1000000 ohm, Rsig = 10000 ohmSOLVEDAv = 0.662252, Rin = 1e+06 ohm, Rout = 396.825 ohm, Gv = 0.655695
Source follower: gm = 5 mS, ro = 20000 ohm, RS = 1000 ohm, RL = 10000 ohm, RG = 470000 ohm, Rsig = 1000 ohmSOLVEDAv = 0.813008, Rin = 470000 ohm, Rout = 165.289 ohm, Gv = 0.811282
Source follower: ro = 50000 ohm, RS = 2000 ohm, RL = 2000 ohm, RG = 1000000 ohm, Rsig = 10000 ohmNEEDS_INPUTelx_source_follower needs gm (transconductance). Example: solve('elx_source_follower', gm='0.002 S', ro='50000 ohm', RS=
Source follower: gm = 2 mS, ro = 50000 ohm, RS = 2000 ohm, RL = 2000 ohm, RG = 1000000 ohm, Rsig = 10000 ohm, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

MOSFET threshold voltage with body effect, elx_mosfet_body_effect

The threshold voltage of a MOSFET whose source is above its body, $Vt = Vt0 + \gamma$ (sqrt(2 phiF + VSB) - sqrt(2 phiF)).

\[V_t = V_{t0} + \gamma\left(\sqrt{2\phi_F + V_{SB}} - \sqrt{2\phi_F}\right)\]
inputmeaningcondition
Vt0zero-bias threshold voltage
gammabody-effect coefficient in $V^{0.5}$
phi2Fsurface potential 2 phi_F (about 0.6 to 0.9 V)
VSBsource-body voltage
outputmeaning
Vtthreshold voltage
dVtthreshold increase
MOSFET threshold voltage with body effect: threshold voltage against source-body voltageVt (threshold voltage) against VSB (source-body voltage) from 0.3 V to 30 V on a logarithmic axis. One curve for each value of Vt0 (zero-bias threshold voltage): 0.7 V, 0.35 V, 1.4 V. Other inputs as in the worked example: gamma = 0.4, phi2F = 0.7 V. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, VSB = 3 V, Vt = 1.13475 V.1101231.13475 VVt0 = 0.7 V (example)Vt0 = 0.35 VVt0 = 1.4 VVSB (source-body voltage [V]Vt), threshold voltage [V]
Vt (threshold voltage) against VSB (source-body voltage) from 0.3 V to 30 V on a logarithmic axis. One curve for each value of Vt0 (zero-bias threshold voltage): 0.7 V, 0.35 V, 1.4 V. Other inputs as in the worked example: gamma = 0.4, phi2F = 0.7 V. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, VSB = 3 V, Vt = 1.13475 V.
electronics_engineering_ai999x.solve('elx_mosfet_body_effect', Vt0=0.7, gamma=0.4, phi2F=0.7, VSB=3.0)
# -> Vt = 1.13475 V, dVt = 0.434751 V   (SOLVED)
electronics_engineering_ai999x.solve('elx_mosfet_body_effect', Vt0=0.5, gamma=0.5, phi2F=0.8, VSB=1.0)
# -> Vt = 0.723607 V, dVt = 0.223607 V   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Body effect threshold voltage: Vt0 = 0.7 V, gamma = 0.4 V^0.5, phi2F = 0.7 V, VSB = 3 VSOLVEDVt = 1.13475 V, dVt = 0.434751 V
Body effect threshold voltage: Vt0 = 0.5 V, gamma = 0.5 V^0.5, phi2F = 0.8 V, VSB = 1 VSOLVEDVt = 0.723607 V, dVt = 0.223607 V
Body effect threshold voltage: gamma = 0.4 V^0.5, phi2F = 0.7 V, VSB = 3 VNEEDS_INPUTelx_mosfet_body_effect needs Vt0 (zero-bias threshold voltage). Example: solve('elx_mosfet_body_effect', Vt0='0.7 V', ga
Body effect threshold voltage: Vt0 = 0.7 V, gamma = 0.4 V^0.5, phi2F = 0.7 V, VSB = 3 V, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te
Body effect threshold voltage: Vt0 = 0.7 V, gamma = 0.4 V^0.5, phi2F = 0.7 V, VSB = 3 VSOLVEDVt = 1.13475 V, dVt = 0.434751 V

CMOS inverter switching threshold VM, elx_cmos_switching_threshold

The switching threshold of a CMOS inverter (input = output, both transistors saturated) from the supply, the two threshold voltages and the two transconductance parameters.

\[V_M = \frac{V_{tn} + r\,(V_{DD} - |V_{tp}|)}{1 + r},\quad r = \sqrt{k_p/k_n}\]
inputmeaningcondition
VDDsupply voltage
VtnNMOS threshold
Vtpmagnitude of the PMOS threshold
knNMOS mu_n Cox W/L
kpPMOS mu_p Cox W/L
outputmeaning
rsqrt(kp/kn)
VMswitching threshold
CMOS inverter switching threshold VM: switching threshold against supply voltageVM (switching threshold) against VDD (supply voltage) from 1.25 V to 3.75 V. One curve for each value of kn (NMOS mu_n Cox W/L): 0.0001 A/V^2, 5.0000e-05 A/V^2, 0.0002 A/V^2. Other inputs as in the worked example: Vtn = 0.4 V, Vtp = 0.4 V, kp = 0.0001 A/V^2. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, VDD = 2.5 V, VM = 1.25 V.230.511.521.25 Vkn = 0.0001 A/V^2 (example)kn = 5.0000e-05 A/V^2kn = 0.0002 A/V^2VDD (supply voltage [V]VM), switching threshold [V]
VM (switching threshold) against VDD (supply voltage) from 1.25 V to 3.75 V. One curve for each value of kn (NMOS mu_n Cox W/L): 0.0001 A/V^2, 5.0000e-05 A/V^2, 0.0002 A/V^2. Other inputs as in the worked example: Vtn = 0.4 V, Vtp = 0.4 V, kp = 0.0001 A/V^2. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, VDD = 2.5 V, VM = 1.25 V.
electronics_engineering_ai999x.solve('elx_cmos_switching_threshold', VDD=2.5, Vtn=0.4, Vtp=0.4, kn=0.0001, kp=0.0001)
# -> r = 1, VM = 1.25 V   (SOLVED)
electronics_engineering_ai999x.solve('elx_cmos_switching_threshold', VDD=3.3, Vtn=0.5, Vtp=0.6, kn=0.0002, kp=8e-05)
# -> r = 0.632456, VM = 1.35234 V   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
CMOS switching threshold: VDD = 2.5 V, Vtn = 0.4 V, Vtp = 0.4 V, kn = 0.1 mA/V^2, kp = 0.1 mA/V^2SOLVEDr = 1, VM = 1.25 V
CMOS switching threshold: VDD = 3.3 V, Vtn = 0.5 V, Vtp = 0.6 V, kn = 0.2 mA/V^2, kp = 0.08 mA/V^2SOLVEDr = 0.632456, VM = 1.35234 V
CMOS switching threshold: Vtn = 0.4 V, Vtp = 0.4 V, kn = 0.1 mA/V^2, kp = 0.1 mA/V^2NEEDS_INPUTelx_cmos_switching_threshold needs VDD (supply voltage). Example: solve('elx_cmos_switching_threshold', VDD='2.5 V', Vtn
CMOS switching threshold: VDD = 2.5 V, Vtn = 0.4 V, Vtp = 0.4 V, kn = 0.1 mA/V^2, kp = 0.1 mA/V^2, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

CMOS gate propagation delay (switch-resistor model), elx_cmos_propagation_delay

The high-to-low and low-to-high propagation delays (50 % points) and their average for a CMOS gate modelled as switched equivalent resistances driving a load capacitance.

\[t_{pHL} = \ln 2\,R_nC_L,\quad t_{pLH} = \ln 2\,R_pC_L\]
inputmeaningcondition
Rnequivalent on-resistance of the pull-down network
Rpequivalent on-resistance of the pull-up network
CLload capacitance
outputmeaning
tpHLhigh-to-low delay
tpLHlow-to-high delay
tpaverage propagation delay
CMOS gate propagation delay (switch-resistor model): average propagation delay against equivalent on-resist…tp (average propagation delay) against Rn (equivalent on-resistance of the pull-down network) from 5000 ohm to 15000 ohm. One curve for each value of CL (load capacitance): 1.0000e-13 F, 5.0000e-14 F, 2.0000e-13 F. Other inputs as in the worked example: Rp = 20000.0 ohm. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Rn = 10000 ohm, tp = 1.0397e-09 s.500075001000012500150005.00e-101.00e-91.50e-92.00e-92.50e-91.0397e-09 sCL = 1.0000e-13 F (example)CL = 5.0000e-14 FCL = 2.0000e-13 FRn [ohm]tp, average propagation delay [s]
tp (average propagation delay) against Rn (equivalent on-resistance of the pull-down network) from 5000 ohm to 15000 ohm. One curve for each value of CL (load capacitance): 1.0000e-13 F, 5.0000e-14 F, 2.0000e-13 F. Other inputs as in the worked example: Rp = 20000.0 ohm. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Rn = 10000 ohm, tp = 1.0397e-09 s.
electronics_engineering_ai999x.solve('elx_cmos_propagation_delay', Rn=10000.0, Rp=20000.0, CL=1e-13)
# -> tpHL = 6.93147e-10 s, tpLH = 1.38629e-09 s, tp = 1.03972e-09 s   (SOLVED)
electronics_engineering_ai999x.solve('elx_cmos_propagation_delay', Rn=5000.0, Rp=12000.0, CL=5e-14)
# -> tpHL = 1.73287e-10 s, tpLH = 4.15888e-10 s, tp = 2.94588e-10 s   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
CMOS propagation delay: Rn = 10000 ohm, Rp = 20000 ohm, CL = 100 fFSOLVEDtpHL = 6.93147e-10 s, tpLH = 1.38629e-09 s, tp = 1.03972e-09 s
CMOS propagation delay: Rn = 5000 ohm, Rp = 12000 ohm, CL = 50 fFSOLVEDtpHL = 1.73287e-10 s, tpLH = 4.15888e-10 s, tp = 2.94588e-10 s
CMOS propagation delay: Rp = 20000 ohm, CL = 100 fFNEEDS_INPUTelx_cmos_propagation_delay needs Rn (equivalent on-resistance of the pull-down network). Example: solve('elx_cmos_propag
CMOS propagation delay: Rn = 10000 ohm, Rp = 20000 ohm, CL = 100 fF, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Inverting op-amp amplifier, elx_inverting_amplifier

The closed-loop gain, output voltage and input resistance of an ideal inverting amplifier.

\[V_{out} = -\frac{R_f}{R_{in}}V_{in}\]
inputmeaningcondition
Rffeedback resistor
Rininput resistor
Vininput voltage
outputmeaning
Gclosed-loop gain -Rf/Rin
Voutoutput voltage
Zininput resistance
Inverting op-amp amplifier: output voltage against input resistorVout (output voltage) against Rin (input resistor) from 1000 ohm to 100000 ohm on a logarithmic axis. One curve for each value of Rf (feedback resistor): 100000 ohm, 50000 ohm, 200000 ohm. Other inputs as in the worked example: Vin = 0.5 V. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Rin = 10000 ohm, Vout = -5 V.1000100001.00e5-100-75-50-250-5 VRf = 100000 ohm (example)Rf = 50000 ohmRf = 200000 ohmRin (input resistor [ohm]Vout), output voltage [V]
Vout (output voltage) against Rin (input resistor) from 1000 ohm to 100000 ohm on a logarithmic axis. One curve for each value of Rf (feedback resistor): 100000 ohm, 50000 ohm, 200000 ohm. Other inputs as in the worked example: Vin = 0.5 V. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Rin = 10000 ohm, Vout = -5 V.
electronics_engineering_ai999x.solve('elx_inverting_amplifier', Rf=100000.0, Rin=10000.0, Vin=0.5)
# -> G = -10, Vout = -5 V, Zin = 10000 ohm   (SOLVED)
electronics_engineering_ai999x.solve('elx_inverting_amplifier', Rf=47000.0, Rin=4700.0, Vin=-0.2)
# -> G = -10, Vout = 2 V, Zin = 4700 ohm   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Inverting amplifier: Rf = 100000 ohm, Rin = 10000 ohm, Vin = 0.5 VSOLVEDG = -10, Vout = -5 V, Zin = 10000 ohm
Inverting amplifier: Rf = 47000 ohm, Rin = 4700 ohm, Vin = -0.2 VSOLVEDG = -10, Vout = 2 V, Zin = 4700 ohm
Inverting amplifier: Rin = 10000 ohm, Vin = 0.5 VNEEDS_INPUTelx_inverting_amplifier needs Rf (feedback resistor). Example: solve('elx_inverting_amplifier', Rf='100000 ohm', Rin='10
Inverting amplifier: Rf = 100000 ohm, Rin = 10000 ohm, Vin = 0.5 V, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Non-inverting op-amp amplifier, elx_noninverting_amplifier

The closed-loop gain $1 + Rf/Rg$ and the output voltage of an ideal non-inverting amplifier.

\[V_{out} = \left(1 + \frac{R_f}{R_g}\right)V_{in}\]
inputmeaningcondition
Rffeedback resistor
Rgresistor from the inverting input to ground
Vininput voltage
outputmeaning
Gclosed-loop gain
Voutoutput voltage
Non-inverting op-amp amplifier: output voltage against resistor from the inverting input to groundVout (output voltage) against Rg (resistor from the inverting input to ground) from 1000 ohm to 100000 ohm on a logarithmic axis. One curve for each value of Vin (input voltage): 0.3 V, 0.15 V, 0.6 V. Other inputs as in the worked example: Rf = 90000.0 ohm. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Rg = 10000 ohm, Vout = 3 V.1000100001.00e5020403 VVin = 0.3 V (example)Vin = 0.15 VVin = 0.6 VRg [ohm]Vout, output voltage [V]
Vout (output voltage) against Rg (resistor from the inverting input to ground) from 1000 ohm to 100000 ohm on a logarithmic axis. One curve for each value of Vin (input voltage): 0.3 V, 0.15 V, 0.6 V. Other inputs as in the worked example: Rf = 90000.0 ohm. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Rg = 10000 ohm, Vout = 3 V.
electronics_engineering_ai999x.solve('elx_noninverting_amplifier', Rf=90000.0, Rg=10000.0, Vin=0.3)
# -> G = 10, Vout = 3 V   (SOLVED)
electronics_engineering_ai999x.solve('elx_noninverting_amplifier', Rf=22000.0, Rg=4700.0, Vin=1.2)
# -> G = 5.68085, Vout = 6.81702 V   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Non-inverting amplifier: Rf = 90000 ohm, Rg = 10000 ohm, Vin = 0.3 VSOLVEDG = 10, Vout = 3 V
Non-inverting amplifier: Rf = 22000 ohm, Rg = 4700 ohm, Vin = 1.2 VSOLVEDG = 5.68085, Vout = 6.81702 V
Non-inverting amplifier: Rg = 10000 ohm, Vin = 0.3 VNEEDS_INPUTelx_noninverting_amplifier needs Rf (feedback resistor). Example: solve('elx_noninverting_amplifier', Rf='90000 ohm', Rg
Non-inverting amplifier: Rf = 90000 ohm, Rg = 10000 ohm, Vin = 0.3 V, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Inverting summing amplifier, elx_summing_amplifier

The output of an ideal inverting summing amplifier with several inputs, each through its own resistor, and the feedback current.

\[V_{out} = -R_f\sum_i\frac{V_i}{R_i}\]
inputmeaningcondition
Vinput voltages in volts
Rinput resistors in kilohms, one per input
Rffeedback resistor
outputmeaning
Voutoutput voltage
I_fcurrent through the feedback resistor
Inverting summing amplifier: output voltage against feedback resistorVout (output voltage) against Rf (feedback resistor) from 5000 ohm to 15000 ohm. Other inputs as in the worked example: V = [1.0, 2.0, -0.5], R = [10.0, 20.0, 5.0]. 31 points computed by electronics-engineering-ai999x; marked: the worked example, Rf = 10000 ohm, Vout = -1 V.50007500100001250015000-1.5-1.25-1-0.75-0.5-1 VRf (feedback resistor [ohm]Vout), output voltage [V]
Vout (output voltage) against Rf (feedback resistor) from 5000 ohm to 15000 ohm. Other inputs as in the worked example: V = [1.0, 2.0, -0.5], R = [10.0, 20.0, 5.0]. 31 points computed by electronics-engineering-ai999x; marked: the worked example, Rf = 10000 ohm, Vout = -1 V.
electronics_engineering_ai999x.solve('elx_summing_amplifier', V=[1.0, 2.0, -0.5], R=[10.0, 20.0, 5.0], Rf=10000.0)
# -> Vout = -1 V, I_f = 0.0001 A   (SOLVED)
electronics_engineering_ai999x.solve('elx_summing_amplifier', V=[0.2, 0.4], R=[1.0, 1.0], Rf=4700.0)
# -> Vout = -2.82 V, I_f = 0.0006 A   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Summing amplifier: V = [1, 2, -0.5], R = [10, 20, 5], Rf = 10000 ohmSOLVEDVout = -1 V, I_f = 0.0001 A
Summing amplifier: V = [0.2, 0.4], R = [1, 1], Rf = 4700 ohmSOLVEDVout = -2.82 V, I_f = 0.0006 A
Summing amplifier: R = [10, 20, 5], Rf = 10000 ohmNEEDS_INPUTelx_summing_amplifier needs V (input voltages in volts). Example: solve('elx_summing_amplifier', V=[1.0, 2.0, -0.5], R=[
Summing amplifier: V = [1, 2, -0.5], R = [10, 20, 5], Rf = 10000 ohm, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Op-amp difference amplifier (with resistor mismatch), elx_difference_amplifier

The output of a one-op-amp difference amplifier with any four resistors, and its differential and common-mode gains (the common-mode gain is zero only when R4/R3 = R2/R1).

\[V_{out} = \frac{R_4}{R_3+R_4}\left(1+\frac{R_2}{R_1}\right)V_2 - \frac{R_2}{R_1}V_1\]
inputmeaningcondition
R1resistor from V1 to the inverting input
R2feedback resistor
R3resistor from V2 to the non-inverting input
R4resistor from the non-inverting input to ground
V1voltage at the inverting side
V2voltage at the non-inverting side
outputmeaning
Voutoutput voltage
Addifferential gain (per volt of V2 - V1)
Acmcommon-mode gain
Op-amp difference amplifier (with resistor mismatch): output voltage against resistor from V1 to the invert…Vout (output voltage) against R1 (resistor from V1 to the inverting input) from 1000 ohm to 100000 ohm on a logarithmic axis. One curve for each value of V2 (voltage at the non-inverting side): 1.2 V, 0.6 V, 2.4 V. Other inputs as in the worked example: R2 = 100000.0 ohm, R3 = 10000.0 ohm, R4 = 100000.0 ohm, V1 = 1.0 V. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R1 = 10000 ohm, Vout = 2 V.1000100001.00e5-500501002 VV2 = 1.2 V (example)V2 = 0.6 VV2 = 2.4 VR1 [ohm]Vout, output voltage [V]
Vout (output voltage) against R1 (resistor from V1 to the inverting input) from 1000 ohm to 100000 ohm on a logarithmic axis. One curve for each value of V2 (voltage at the non-inverting side): 1.2 V, 0.6 V, 2.4 V. Other inputs as in the worked example: R2 = 100000.0 ohm, R3 = 10000.0 ohm, R4 = 100000.0 ohm, V1 = 1.0 V. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R1 = 10000 ohm, Vout = 2 V.
electronics_engineering_ai999x.solve('elx_difference_amplifier', R1=10000.0, R2=100000.0, R3=10000.0, R4=100000.0, V1=1.0, V2=1.2)
# -> Vout = 2 V, Ad = 10, Acm = 0   (SOLVED)
electronics_engineering_ai999x.solve('elx_difference_amplifier', R1=10000.0, R2=50000.0, R3=10500.0, R4=49000.0, V1=2.0, V2=2.1)
# -> Vout = 0.376471 V, Ad = 4.97059, Acm = -0.0588235   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Difference amplifier: R1 = 10000 ohm, R2 = 100000 ohm, R3 = 10000 ohm, R4 = 100000 ohm, V1 = 1 V, V2 = 1.2 VSOLVEDVout = 2 V, Ad = 10, Acm = 0
Difference amplifier: R1 = 10000 ohm, R2 = 50000 ohm, R3 = 10500 ohm, R4 = 49000 ohm, V1 = 2 V, V2 = 2.1 VSOLVEDVout = 0.376471 V, Ad = 4.97059, Acm = -0.0588235
Difference amplifier: R2 = 100000 ohm, R3 = 10000 ohm, R4 = 100000 ohm, V1 = 1 V, V2 = 1.2 VNEEDS_INPUTelx_difference_amplifier needs R1 (resistor from V1 to the inverting input). Example: solve('elx_difference_amplifier',
Difference amplifier: R1 = 10000 ohm, R2 = 100000 ohm, R3 = 10000 ohm, R4 = 100000 ohm, V1 = 1 V, V2 = 1.2 V, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Three-op-amp instrumentation amplifier, elx_instrumentation_amplifier

The gain and output of the classic three-op-amp instrumentation amplifier: input stage gain $1 + 2$ $R_{1}/RG$ times the difference stage gain $R_{3}/R_{2}.$

\[V_{out} = \left(1 + \frac{2R_1}{R_G}\right)\frac{R_3}{R_2}(V_2 - V_1)\]
inputmeaningcondition
R1feedback resistor of each input buffer
RGgain-setting resistor between the buffers
R2input resistors of the difference stage
R3feedback and ground resistors of the difference stage
V1input at the inverting side
V2input at the non-inverting side
outputmeaning
Gdifferential gain
G_stage1gain of the input stage
Voutoutput voltage
Three-op-amp instrumentation amplifier: output voltage against gain-setting resistor between the buffersVout (output voltage) against RG (gain-setting resistor between the buffers) from 500 ohm to 1500 ohm. One curve for each value of V2 (input at the non-inverting side): 1.01 V, 0.505 V, 2.02 V. Other inputs as in the worked example: R1 = 25000.0 ohm, R2 = 10000.0 ohm, R3 = 10000.0 ohm, V1 = 1.0 V. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, RG = 1000 ohm, Vout = 0.51 V.500750100012501500-500501000.51 VV2 = 1.01 V (example)V2 = 0.505 VV2 = 2.02 VRG [ohm]Vout, output voltage [V]
Vout (output voltage) against RG (gain-setting resistor between the buffers) from 500 ohm to 1500 ohm. One curve for each value of V2 (input at the non-inverting side): 1.01 V, 0.505 V, 2.02 V. Other inputs as in the worked example: R1 = 25000.0 ohm, R2 = 10000.0 ohm, R3 = 10000.0 ohm, V1 = 1.0 V. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, RG = 1000 ohm, Vout = 0.51 V.
electronics_engineering_ai999x.solve('elx_instrumentation_amplifier', R1=25000.0, RG=1000.0, R2=10000.0, R3=10000.0, V1=1.0, V2=1.01)
# -> G = 51, G_stage1 = 51, Vout = 0.51 V   (SOLVED)
electronics_engineering_ai999x.solve('elx_instrumentation_amplifier', R1=49400.0, RG=494.0, R2=10000.0, R3=20000.0, V1=0.5, V2=0.502)
# -> G = 402, G_stage1 = 201, Vout = 0.804 V   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Instrumentation amplifier: R1 = 25000 ohm, RG = 1000 ohm, R2 = 10000 ohm, R3 = 10000 ohm, V1 = 1 V, V2 = 1.01 VSOLVEDG = 51, G_stage1 = 51, Vout = 0.51 V
Instrumentation amplifier: R1 = 49400 ohm, RG = 494 ohm, R2 = 10000 ohm, R3 = 20000 ohm, V1 = 0.5 V, V2 = 0.502 VSOLVEDG = 402, G_stage1 = 201, Vout = 0.804 V
Instrumentation amplifier: RG = 1000 ohm, R2 = 10000 ohm, R3 = 10000 ohm, V1 = 1 V, V2 = 1.01 VNEEDS_INPUTelx_instrumentation_amplifier needs R1 (feedback resistor of each input buffer). Example: solve('elx_instrumentation_amp
Instrumentation amplifier: R1 = 25000 ohm, RG = 1000 ohm, R2 = 10000 ohm, R3 = 10000 ohm, V1 = 1 V, V2 = 1.01 V, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Inverting amplifier with finite open-loop gain, elx_inverting_amplifier_finite_gain

The exact closed-loop gain of an inverting amplifier built with an op-amp of finite open-loop gain A0, its relative gain error and output.

\[G = \frac{-R_f/R_1}{1 + \dfrac{1 + R_f/R_1}{A_0}}\]
inputmeaningcondition
Rffeedback resistor
R1input resistor
A0open-loop voltage gain (a ratio, not dB)
Vininput voltage
outputmeaning
Gclosed-loop gain
G_idealideal gain -Rf/R1
Voutoutput voltage
errorrelative gain error 1 - G/G_ideal
Inverting amplifier with finite open-loop gain: closed-loop gain against feedback resistorG (closed-loop gain) against Rf (feedback resistor) from 10000 ohm to 1e+06 ohm on a logarithmic axis. One curve for each value of R1 (input resistor): 1000 ohm, 500 ohm, 2000 ohm. Other inputs as in the worked example: A0 = 10000.0, Vin = 0.01 V. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Rf = 100000 ohm, G = -99.0001.100001.00e51.00e6-1500-1000-5000-99.0001R1 = 1000 ohm (example)R1 = 500 ohmR1 = 2000 ohmRf (feedback resistor [ohm]G), closed-loop gain
G (closed-loop gain) against Rf (feedback resistor) from 10000 ohm to 1e+06 ohm on a logarithmic axis. One curve for each value of R1 (input resistor): 1000 ohm, 500 ohm, 2000 ohm. Other inputs as in the worked example: A0 = 10000.0, Vin = 0.01 V. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Rf = 100000 ohm, G = -99.0001.
electronics_engineering_ai999x.solve('elx_inverting_amplifier_finite_gain', Rf=100000.0, R1=1000.0, A0=10000.0, Vin=0.01)
# -> G = -99.0001, G_ideal = -100, Vout = -0.990001 V, error = 0.00999901   (SOLVED)
electronics_engineering_ai999x.solve('elx_inverting_amplifier_finite_gain', Rf=10000.0, R1=1000.0, A0=1000.0, Vin=0.1)
# -> G = -9.8912, G_ideal = -10, Vout = -0.98912 V, error = 0.0108803   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Inverting amplifier with finite gain: Rf = 100000 ohm, R1 = 1000 ohm, A0 = 10000, Vin = 0.01 VSOLVEDG = -99.0001, G_ideal = -100, Vout = -0.990001 V, error = 0.00999901
Inverting amplifier with finite gain: Rf = 10000 ohm, R1 = 1000 ohm, A0 = 1000, Vin = 0.1 VSOLVEDG = -9.8912, G_ideal = -10, Vout = -0.98912 V, error = 0.0108803
Inverting amplifier with finite gain: R1 = 1000 ohm, A0 = 10000, Vin = 0.01 VNEEDS_INPUTelx_inverting_amplifier_finite_gain needs Rf (feedback resistor). Example: solve('elx_inverting_amplifier_finite_gain',
Inverting amplifier with finite gain: Rf = 100000 ohm, R1 = 1000 ohm, A0 = 10000, Vin = 0.01 V, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Op-amp integrator: output ramp and unity-gain frequency, elx_opamp_integrator

The output of an ideal inverting integrator after a time with a constant input, its ramp rate, and the frequency at which its gain is one.

\[V_{out}(t) = V_0 - \frac{1}{RC}\int_0^t V_{in}\,dt\]
inputmeaningcondition
Rinput resistor
Cfeedback capacitor
Vinconstant input voltage
ttime since the start
V0initial output voltage (default 0)
outputmeaning
Voutoutput voltage at t
slopeoutput ramp rate
f_unityunity-gain frequency 1/(2 pi R C)
Op-amp integrator: output ramp and unity-gain frequency: output voltage at t against input resistorVout (output voltage at t) against R (input resistor) from 1000 ohm to 100000 ohm on a logarithmic axis. One curve for each value of C (feedback capacitor): 1.0000e-06 F, 5.0000e-07 F, 2.0000e-06 F. Other inputs as in the worked example: Vin = 0.5 V, t = 0.002 s. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R = 10000 ohm, Vout = -0.1 V.1000100001.00e5-2-1.5-1-0.50-0.1 VC = 1.0000e-06 F (example)C = 5.0000e-07 FC = 2.0000e-06 FR (input resistor [ohm]Vout), output voltage at t [V]
Vout (output voltage at t) against R (input resistor) from 1000 ohm to 100000 ohm on a logarithmic axis. One curve for each value of C (feedback capacitor): 1.0000e-06 F, 5.0000e-07 F, 2.0000e-06 F. Other inputs as in the worked example: Vin = 0.5 V, t = 0.002 s. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R = 10000 ohm, Vout = -0.1 V.
electronics_engineering_ai999x.solve('elx_opamp_integrator', R=10000.0, C=1e-06, Vin=0.5, t=0.002)
# -> Vout = -0.1 V, slope = -50 V/s, f_unity = 15.9155 Hz   (SOLVED)
electronics_engineering_ai999x.solve('elx_opamp_integrator', R=100000.0, C=1e-07, Vin=-1.0, t=0.005, V0=-2.0)
# -> Vout = -1.5 V, slope = 100 V/s, f_unity = 15.9155 Hz   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Op-amp integrator: R = 10000 ohm, C = 1 uF, Vin = 0.5 V, t = 2 msSOLVEDVout = -0.1 V, slope = -50 V/s, f_unity = 15.9155 Hz
Op-amp integrator: R = 100000 ohm, C = 0.1 uF, Vin = -1 V, t = 5 ms, V0 = -2 VSOLVEDVout = -1.5 V, slope = 100 V/s, f_unity = 15.9155 Hz
Op-amp integrator: C = 1 uF, Vin = 0.5 V, t = 2 msNEEDS_INPUTelx_opamp_integrator needs R (input resistor). Example: solve('elx_opamp_integrator', R='10000 ohm', C='1e-06 F', Vin='0
Op-amp integrator: R = 10000 ohm, C = 1 uF, Vin = 0.5 V, t = 2 ms, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Op-amp differentiator: gain and output amplitude, elx_opamp_differentiator

The gain |H| = 2 pi f R C of an ideal inverting differentiator at a frequency and the peak output for a sinusoidal input of given amplitude.

\[|H(j\omega)| = \omega RC\]
inputmeaningcondition
Rfeedback resistor
Cinput capacitor
Apeak input amplitude
finput frequency
outputmeaning
gaingain magnitude
Vout_peakpeak output voltage
gain_dBgain in dB
Op-amp differentiator: gain and output amplitude: peak output voltage against feedback resistorVout_peak (peak output voltage) against R (feedback resistor) from 5000 ohm to 15000 ohm. One curve for each value of C (input capacitor): 1.0000e-08 F, 5.0000e-09 F, 2.0000e-08 F. Other inputs as in the worked example: A = 1.0 V, f = 1000.0 Hz. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R = 10000 ohm, Vout_peak = 0.628319 V.500075001000012500150000.511.520.628319 VC = 1.0000e-08 F (example)C = 5.0000e-09 FC = 2.0000e-08 FR (feedback resistor [ohm]Vout_peak), peak output voltage [V]
Vout_peak (peak output voltage) against R (feedback resistor) from 5000 ohm to 15000 ohm. One curve for each value of C (input capacitor): 1.0000e-08 F, 5.0000e-09 F, 2.0000e-08 F. Other inputs as in the worked example: A = 1.0 V, f = 1000.0 Hz. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R = 10000 ohm, Vout_peak = 0.628319 V.
electronics_engineering_ai999x.solve('elx_opamp_differentiator', R=10000.0, C=1e-08, A=1.0, f=1000.0)
# -> gain = 0.628319, Vout_peak = 0.628319 V, gain_dB = -4.0364   (SOLVED)
electronics_engineering_ai999x.solve('elx_opamp_differentiator', R=100000.0, C=1e-09, A=0.5, f=500.0)
# -> gain = 0.314159, Vout_peak = 0.15708 V, gain_dB = -10.057   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Op-amp differentiator: R = 10000 ohm, C = 10 nF, A = 1 V, f = 1000 HzSOLVEDgain = 0.628319, Vout_peak = 0.628319 V, gain_dB = -4.0364
Op-amp differentiator: R = 100000 ohm, C = 1 nF, A = 0.5 V, f = 500 HzSOLVEDgain = 0.314159, Vout_peak = 0.15708 V, gain_dB = -10.057
Op-amp differentiator: C = 10 nF, A = 1 V, f = 1000 HzNEEDS_INPUTelx_opamp_differentiator needs R (feedback resistor). Example: solve('elx_opamp_differentiator', R='10000 ohm', C='1e-08
Op-amp differentiator: R = 10000 ohm, C = 10 nF, A = 1 V, f = 1000 Hz, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Closed-loop bandwidth from the gain-bandwidth product, elx_closed_loop_bandwidth

The closed-loop gain, the noise gain $1 + Rf/R_{1}$ and the -3 dB bandwidth GBW/(noise gain) of an inverting or non-inverting amplifier built with a single-pole op-amp.

\[f_{3dB} = \frac{\text{GBW}}{1 + R_f/R_1}\]
inputmeaningcondition
GBWgain-bandwidth product (unity-gain frequency)
configinverting or non-inverting amplifier
Rffeedback resistor
R1input (or ground) resistor
outputmeaning
G0low-frequency closed-loop gain
noise_gainnoise gain $1 + Rf/R_{1}$
f_3dBclosed-loop -3 dB bandwidth
Closed-loop bandwidth from the gain-bandwidth product: closed-loop -3 dB bandwidth against feedback resistorf_3dB (closed-loop -3 dB bandwidth) against Rf (feedback resistor) from 9000 ohm to 900000 ohm on a logarithmic axis. One curve for each value of GBW (gain-bandwidth product (unity-gain frequency)): 1e+06 Hz, 500000 Hz, 2e+06 Hz. Other inputs as in the worked example: config = non-inverting, R1 = 10000.0 ohm. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Rf = 90000 ohm, f_3dB = 100000 Hz.100001.00e51.00e602.50e55.00e57.50e51.00e6100000 HzGBW = 1e+06 Hz (example)GBW = 500000 HzGBW = 2e+06 HzRf (feedback resistor [ohm]f_3dB), closed-loop -3 dB bandwidth [Hz]
f_3dB (closed-loop -3 dB bandwidth) against Rf (feedback resistor) from 9000 ohm to 900000 ohm on a logarithmic axis. One curve for each value of GBW (gain-bandwidth product (unity-gain frequency)): 1e+06 Hz, 500000 Hz, 2e+06 Hz. Other inputs as in the worked example: config = non-inverting, R1 = 10000.0 ohm. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Rf = 90000 ohm, f_3dB = 100000 Hz.
electronics_engineering_ai999x.solve('elx_closed_loop_bandwidth', GBW=1000000.0, config='non-inverting', Rf=90000.0, R1=10000.0)
# -> G0 = 10, noise_gain = 10, f_3dB = 100000 Hz   (SOLVED)
electronics_engineering_ai999x.solve('elx_closed_loop_bandwidth', GBW=10000000.0, config='inverting', Rf=100000.0, R1=10000.0)
# -> G0 = -10, noise_gain = 11, f_3dB = 909091 Hz   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Closed-loop bandwidth: GBW = 1000000 Hz, config = non-inverting, Rf = 90000 ohm, R1 = 10000 ohmSOLVEDG0 = 10, noise_gain = 10, f_3dB = 100000 Hz
Closed-loop bandwidth: GBW = 10000000 Hz, config = inverting, Rf = 100000 ohm, R1 = 10000 ohmSOLVEDG0 = -10, noise_gain = 11, f_3dB = 909091 Hz
Closed-loop bandwidth: config = non-inverting, Rf = 90000 ohm, R1 = 10000 ohmNEEDS_INPUTelx_closed_loop_bandwidth needs GBW (gain-bandwidth product (unity-gain frequency)). Example: solve('elx_closed_loop_ban
Closed-loop bandwidth: GBW = 1000000 Hz, config = non-inverting, Rf = 90000 ohm, R1 = 10000 ohm, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te
Closed-loop bandwidth: GBW = 1 MHz, config = non-inverting, Rf = 90 kohm, R1 = 10 kohmSOLVEDG0 = 10, noise_gain = 10, f_3dB = 100000 Hz

Slew-rate limit: full-power bandwidth, elx_slew_rate_limit

The full-power bandwidth SR/(2 pi Vp) of an op-amp, the largest undistorted amplitude at a frequency, the slope a sine wave needs and whether it is slew-limited.

\[f_{max} = \frac{SR}{2\pi V_p}\]
inputmeaningcondition
SRslew rate
Vppeak output amplitude
fsignal frequency
outputmeaning
f_maxfull-power bandwidth at Vp
Vp_maxlargest undistorted amplitude at f
slope_neededmaximum slope of the sine, 2 pi f Vp
limitedslew-limited or not slew-limited
Slew-rate limit: full-power bandwidth: where the verdict changes (limited)slew-limited or not slew-limited (limited) over SR (slew rate) from 50000 V/s to 5e+06 V/s and Vp (peak output amplitude) from 1 V to 100 V (logarithmic axes): each of the 31 × 21 cells is one run of electronics-engineering-ai999x, coloured by the verdict it returned, not slew-limited: 208 cells, slew-limited: 443 cells. Other inputs as in the worked example: f = 20000.0 Hz. Marked: the worked example, SR = 500000 V/s, Vp = 10 V → slew-limited.1.00e51.00e6110100slew-limitedlimited: not slew-limited (208)limited: slew-limited (443)SR (slew rate [V/s]Vp), peak output amplitude [V]
slew-limited or not slew-limited (limited) over SR (slew rate) from 50000 V/s to 5e+06 V/s and Vp (peak output amplitude) from 1 V to 100 V (logarithmic axes): each of the 31 × 21 cells is one run of electronics-engineering-ai999x, coloured by the verdict it returned, not slew-limited: 208 cells, slew-limited: 443 cells. Other inputs as in the worked example: f = 20000.0 Hz. Marked: the worked example, SR = 500000 V/s, Vp = 10 V → slew-limited.
Slew-rate limit: full-power bandwidth: full-power bandwidth at Vp against peak output amplitudef_max (full-power bandwidth at Vp) against Vp (peak output amplitude) from 5 V to 15 V. One curve for each value of SR (slew rate): 500000 V/s, 250000 V/s, 1e+06 V/s. Other inputs as in the worked example: f = 20000.0 Hz. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Vp = 10 V, f_max = 7957.75 Hz.57.51012.5151000020000300007957.75 HzSR = 500000 V/s (example)SR = 250000 V/sSR = 1e+06 V/sVp (peak output amplitude [V]f_max), full-power bandwidth at Vp [Hz]
f_max (full-power bandwidth at Vp) against Vp (peak output amplitude) from 5 V to 15 V. One curve for each value of SR (slew rate): 500000 V/s, 250000 V/s, 1e+06 V/s. Other inputs as in the worked example: f = 20000.0 Hz. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Vp = 10 V, f_max = 7957.75 Hz.
electronics_engineering_ai999x.solve('elx_slew_rate_limit', SR=500000.0, Vp=10.0, f=20000.0)
# -> f_max = 7957.75 Hz, Vp_max = 3.97887 V, slope_needed = 1.25664e+06 V/s, limited = slew-limited   (SOLVED)
electronics_engineering_ai999x.solve('elx_slew_rate_limit', SR=13000000.0, Vp=5.0, f=100000.0)
# -> f_max = 413803 Hz, Vp_max = 20.6901 V, slope_needed = 3.14159e+06 V/s, limited = not slew-limited   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Slew-rate limit: SR = 0.5 V/us, Vp = 10 V, f = 20000 HzSOLVEDf_max = 7957.75 Hz, Vp_max = 3.97887 V, slope_needed = 1.25664e+06 V/s, limited = slew-limited
Slew-rate limit: SR = 13 V/us, Vp = 5 V, f = 100000 HzSOLVEDf_max = 413803 Hz, Vp_max = 20.6901 V, slope_needed = 3.14159e+06 V/s, limited = not slew-limited
Slew-rate limit: Vp = 10 V, f = 20000 HzNEEDS_INPUTelx_slew_rate_limit needs SR (slew rate). Example: solve('elx_slew_rate_limit', SR='500000 V/s', Vp='10 V', f='20000 Hz'
Slew-rate limit: SR = 0.5 V/us, Vp = 10 V, f = 20000 Hz, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Op-amp output offset from input offset voltage and bias currents, elx_opamp_dc_offset

The DC output error of an inverting or non-inverting amplifier (input grounded) caused by the input offset voltage and the input bias and offset currents, and the compensating resistor that cancels the bias-current error.

\[V_{out} = \left(V_{os} - I_{B+}R_p\right)\left(1 + \frac{R_f}{R_1}\right) + I_{B-}R_f\]
inputmeaningcondition
Vosinput offset voltage (in series with the + input)
IBaverage input bias current
Iosinput offset current IB- minus IB+
Rffeedback resistor
R1resistor from the inverting input to ground
Rpresistor from the + input to ground (0 if none)
outputmeaning
Vout_Vosoutput error from Vos
Vout_biasoutput error from the bias currents
Vout_totaltotal output error
Rp_optimalbias-cancelling $Rp = R_{1}$ || Rf
Op-amp output offset from input offset voltage and bias currents: total output error against resistor from…Vout_total (total output error) against R1 (resistor from the inverting input to ground) from 1000 ohm to 100000 ohm on a logarithmic axis. One curve for each value of Rf (feedback resistor): 100000 ohm, 50000 ohm, 200000 ohm. Other inputs as in the worked example: Vos = 0.002 V, IB = 1.0000000000000001e-07 A, Ios = 1e-08 A, Rp = 0.0 ohm. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R1 = 10000 ohm, Vout_total = 0.0325 V.1000100001.00e500.10.20.30.40.0325 VRf = 100000 ohm (example)Rf = 50000 ohmRf = 200000 ohmR1 [ohm]Vout_total, total output error [V]
Vout_total (total output error) against R1 (resistor from the inverting input to ground) from 1000 ohm to 100000 ohm on a logarithmic axis. One curve for each value of Rf (feedback resistor): 100000 ohm, 50000 ohm, 200000 ohm. Other inputs as in the worked example: Vos = 0.002 V, IB = 1.0000000000000001e-07 A, Ios = 1e-08 A, Rp = 0.0 ohm. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R1 = 10000 ohm, Vout_total = 0.0325 V.
electronics_engineering_ai999x.solve('elx_opamp_dc_offset', Vos=0.002, IB=1e-07, Ios=1e-08, Rf=100000.0, R1=10000.0, Rp=0.0)
# -> Vout_Vos = 0.022 V, Vout_bias = 0.0105 V, Vout_total = 0.0325 V, Rp_optimal = 9090.91 ohm   (SOLVED)
electronics_engineering_ai999x.solve('elx_opamp_dc_offset', Vos=0.001, IB=8e-08, Ios=2e-08, Rf=100000.0, R1=10000.0, Rp=9100.0)
# -> Vout_Vos = 0.011 V, Vout_bias = 0.001993 V, Vout_total = 0.012993 V, Rp_optimal = 9090.91 ohm   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Op-amp output offset: Vos = 2 mV, IB = 100 nA, Ios = 10 nA, Rf = 100000 ohm, R1 = 10000 ohm, Rp = 0 ohmSOLVEDVout_Vos = 0.022 V, Vout_bias = 0.0105 V, Vout_total = 0.0325 V, Rp_optimal = 9090.91 ohm
Op-amp output offset: Vos = 1 mV, IB = 80 nA, Ios = 20 nA, Rf = 100000 ohm, R1 = 10000 ohm, Rp = 9100 ohmSOLVEDVout_Vos = 0.011 V, Vout_bias = 0.001993 V, Vout_total = 0.012993 V, Rp_optimal = 9090.91 ohm
Op-amp output offset: IB = 100 nA, Ios = 10 nA, Rf = 100000 ohm, R1 = 10000 ohm, Rp = 0 ohmNEEDS_INPUTelx_opamp_dc_offset needs Vos (input offset voltage (in series with the + input)). Example: solve('elx_opamp_dc_offset',
Op-amp output offset: Vos = 2 mV, IB = 100 nA, Ios = 10 nA, Rf = 100000 ohm, R1 = 10000 ohm, Rp = 0 ohm, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Inverting Schmitt trigger thresholds, elx_schmitt_trigger

The upper and lower switching thresholds, the hysteresis width and the centre of an inverting op-amp Schmitt trigger whose positive feedback divider (Rf from the output, R1 to a reference) sets the + input.

\[V_{TH,TL} = \frac{V_{sat}R_1 + V_{ref}R_f}{R_1 + R_f}\]
inputmeaningcondition
Rfresistor from the output to the + input
R1resistor from the + input to Vref
VsatHhigh output saturation voltage
VsatLlow output saturation voltage (negative for a split supply)
Vrefreference voltage (0 V for ground)
outputmeaning
V_THupper threshold
V_TLlower threshold
hysteresishysteresis width
centercentre of the hysteresis band
Inverting Schmitt trigger thresholds: hysteresis width against resistor from the output to the + inputhysteresis (hysteresis width) against Rf (resistor from the output to the + input) from 9000 ohm to 900000 ohm on a logarithmic axis. One curve for each value of R1 (resistor from the + input to Vref): 10000 ohm, 5000 ohm, 20000 ohm. Other inputs as in the worked example: VsatH = 12.0 V, VsatL = -12.0 V, Vref = 0.0 V. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Rf = 90000 ohm, hysteresis = 2.4 V.100001.00e51.00e60510152.4 VR1 = 10000 ohm (example)R1 = 5000 ohmR1 = 20000 ohmRf [ohm]hysteresis, hysteresis width [V]
hysteresis (hysteresis width) against Rf (resistor from the output to the + input) from 9000 ohm to 900000 ohm on a logarithmic axis. One curve for each value of R1 (resistor from the + input to Vref): 10000 ohm, 5000 ohm, 20000 ohm. Other inputs as in the worked example: VsatH = 12.0 V, VsatL = -12.0 V, Vref = 0.0 V. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Rf = 90000 ohm, hysteresis = 2.4 V.
electronics_engineering_ai999x.solve('elx_schmitt_trigger', Rf=90000.0, R1=10000.0, VsatH=12.0, VsatL=-12.0, Vref=0.0)
# -> V_TH = 1.2 V, V_TL = -1.2 V, hysteresis = 2.4 V, center = 0 V   (SOLVED)
electronics_engineering_ai999x.solve('elx_schmitt_trigger', Rf=100000.0, R1=22000.0, VsatH=4.8, VsatL=0.1, Vref=2.5)
# -> V_TH = 2.91475 V, V_TL = 2.06721 V, hysteresis = 0.847541 V, center = 2.49098 V   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Schmitt trigger thresholds: Rf = 90000 ohm, R1 = 10000 ohm, VsatH = 12 V, VsatL = -12 V, Vref = 0 VSOLVEDV_TH = 1.2 V, V_TL = -1.2 V, hysteresis = 2.4 V, center = 0 V
Schmitt trigger thresholds: Rf = 100000 ohm, R1 = 22000 ohm, VsatH = 4.8 V, VsatL = 0.1 V, Vref = 2.5 VSOLVEDV_TH = 2.91475 V, V_TL = 2.06721 V, hysteresis = 0.847541 V, center = 2.49098 V
Schmitt trigger thresholds: R1 = 10000 ohm, VsatH = 12 V, VsatL = -12 V, Vref = 0 VNEEDS_INPUTelx_schmitt_trigger needs Rf (resistor from the output to the + input). Example: solve('elx_schmitt_trigger', Rf='90000
Schmitt trigger thresholds: Rf = 90000 ohm, R1 = 10000 ohm, VsatH = 12 V, VsatL = -12 V, Vref = 0 V, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Negative feedback: closed-loop gain and bandwidth extension, elx_negative_feedback

The closed-loop gain A/(1 + A beta), the loop gain, the desensitivity factor (also in dB) and the extended bandwidth of a single-pole amplifier with negative feedback.

\[A_f = \frac{A}{1 + A\beta},\quad f_{H,f} = f_H(1 + A\beta)\]
inputmeaningcondition
Aopen-loop gain (a ratio)
betafeedback factor (a ratio)
fHopen-loop -3 dB bandwidth
outputmeaning
Afclosed-loop gain
loop_gainloop gain A beta
desensitivity$1 + A$ beta
desensitivity_dBamount of feedback in dB
fH_closedclosed-loop bandwidth
Negative feedback: closed-loop gain and bandwidth extension: closed-loop gain against feedback factor (a ra…Af (closed-loop gain) against beta (feedback factor (a ratio)) from 0.02 to 0.98. Other inputs as in the worked example: A = 10000.0, fH = 1000.0 Hz. 41 points computed by electronics-engineering-ai999x; marked: the worked example, beta = 0.01, Af = 99.0099.00.250.50.751025507510099.0099beta (feedback factor (a ratio)Af), closed-loop gain
Af (closed-loop gain) against beta (feedback factor (a ratio)) from 0.02 to 0.98. Other inputs as in the worked example: A = 10000.0, fH = 1000.0 Hz. 41 points computed by electronics-engineering-ai999x; marked: the worked example, beta = 0.01, Af = 99.0099.
electronics_engineering_ai999x.solve('elx_negative_feedback', A=10000.0, beta=0.01, fH=1000.0)
# -> Af = 99.0099, loop_gain = 100, desensitivity = 101, desensitivity_dB = 40.0864, fH_closed = 101000 Hz   (SOLVED)
electronics_engineering_ai999x.solve('elx_negative_feedback', A=200000.0, beta=0.1, fH=10.0)
# -> Af = 9.9995, loop_gain = 20000, desensitivity = 20001, desensitivity_dB = 86.021, fH_closed = 200010 Hz   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Negative feedback amplifier: A = 10000, beta = 0.01, fH = 1000 HzSOLVEDAf = 99.0099, loop_gain = 100, desensitivity = 101, desensitivity_dB = 40.0864, fH_closed = 101000 Hz
Negative feedback amplifier: A = 200000, beta = 0.1, fH = 10 HzSOLVEDAf = 9.9995, loop_gain = 20000, desensitivity = 20001, desensitivity_dB = 86.021, fH_closed = 200010 Hz
Negative feedback amplifier: beta = 0.01, fH = 1000 HzNEEDS_INPUTelx_negative_feedback needs A (open-loop gain (a ratio)). Example: solve('elx_negative_feedback', A=10000, beta=0.01, fH
Negative feedback amplifier: A = 10000, beta = 0.01, fH = 1000 Hz, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Phase margin of a two-pole amplifier with feedback, elx_two_pole_phase_margin

The loop-gain crossover frequency and the phase margin of an amplifier with two real poles and a frequency-independent feedback factor, and its closed-loop DC gain.

\[PM = 180^\circ - \arctan\frac{f_c}{f_1} - \arctan\frac{f_c}{f_2}\]
inputmeaningcondition
A0DC open-loop gain (a ratio)
f1first pole frequency
f2second pole frequency
betafeedback factor
outputmeaning
f_cloop-gain crossover frequency
PM_degphase margin in degrees
Afclosed-loop DC gain
Phase margin of a two-pole amplifier with feedback: phase margin in degrees against DC open-loop gain (a ra…PM_deg (phase margin in degrees) against A0 (DC open-loop gain (a ratio)) from 10000 to 1e+06 on a logarithmic axis. One curve for each value of f1 (first pole frequency): 10 Hz, 5 Hz, 20 Hz. Other inputs as in the worked example: f2 = 1000000.0 Hz, beta = 0.1. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, A0 = 100000, PM_deg = 84.323.100001.00e51.00e640608084.323f1 = 10 Hz (example)f1 = 5 Hzf1 = 20 HzA0 (DC open-loop gain (a ratio)PM_deg), phase margin in degrees
PM_deg (phase margin in degrees) against A0 (DC open-loop gain (a ratio)) from 10000 to 1e+06 on a logarithmic axis. One curve for each value of f1 (first pole frequency): 10 Hz, 5 Hz, 20 Hz. Other inputs as in the worked example: f2 = 1000000.0 Hz, beta = 0.1. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, A0 = 100000, PM_deg = 84.323.
electronics_engineering_ai999x.solve('elx_two_pole_phase_margin', A0=100000.0, f1=10.0, f2=1000000.0, beta=0.1)
# -> f_c = 99508.5 Hz, PM_deg = 84.323, Af = 9.999   (SOLVED)
electronics_engineering_ai999x.solve('elx_two_pole_phase_margin', A0=20000.0, f1=100.0, f2=200000.0, beta=1.0)
# -> f_c = 616847 Hz, PM_deg = 17.9735, Af = 0.99995   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Two-pole phase margin: A0 = 100000, f1 = 10 Hz, f2 = 1000000 Hz, beta = 0.1SOLVEDf_c = 99508.5 Hz, PM_deg = 84.323, Af = 9.999
Two-pole phase margin: A0 = 20000, f1 = 100 Hz, f2 = 200000 Hz, beta = 1SOLVEDf_c = 616847 Hz, PM_deg = 17.9735, Af = 0.99995
Two-pole phase margin: f1 = 10 Hz, f2 = 1000000 Hz, beta = 0.1NEEDS_INPUTelx_two_pole_phase_margin needs A0 (DC open-loop gain (a ratio)). Example: solve('elx_two_pole_phase_margin', A0=100000,
Two-pole phase margin: A0 = 100000, f1 = 10 Hz, f2 = 1000000 Hz, beta = 0.1, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

First-order active low-pass filter (inverting), elx_first_order_active_lowpass

The passband gain -Rf/R1, the cutoff frequency 1/(2 pi Rf C) and the gain at a frequency of an inverting op-amp low-pass filter with C across the feedback resistor.

\[H(j\omega) = -\frac{R_f/R_1}{1 + j\omega R_fC},\quad f_c = \frac{1}{2\pi R_fC}\]
inputmeaningcondition
R1input resistor
Rffeedback resistor
Ccapacitor across Rf
ffrequency of interest
outputmeaning
H0passband gain
fccutoff frequency
gain_fgain magnitude at f
gain_dBgain at f in dB
First-order active low-pass filter (inverting): cutoff frequency against feedback resistorfc (cutoff frequency) against Rf (feedback resistor) from 50000 ohm to 150000 ohm. One curve for each value of C (capacitor across Rf): 1.5900e-09 F, 7.9500e-10 F, 3.1800e-09 F. Other inputs as in the worked example: R1 = 10000.0 ohm, f = 1000.0 Hz. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Rf = 100000 ohm, fc = 1000.97 Hz.50000750001.00e51.25e51.50e510002000300040001000.97 HzC = 1.5900e-09 F (example)C = 7.9500e-10 FC = 3.1800e-09 FRf (feedback resistor [ohm]fc), cutoff frequency [Hz]
fc (cutoff frequency) against Rf (feedback resistor) from 50000 ohm to 150000 ohm. One curve for each value of C (capacitor across Rf): 1.5900e-09 F, 7.9500e-10 F, 3.1800e-09 F. Other inputs as in the worked example: R1 = 10000.0 ohm, f = 1000.0 Hz. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Rf = 100000 ohm, fc = 1000.97 Hz.
electronics_engineering_ai999x.solve('elx_first_order_active_lowpass', R1=10000.0, Rf=100000.0, C=1.59e-09, f=1000.0)
# -> H0 = -10, fc = 1000.97 Hz, gain_f = 7.07451, gain_dB = 16.9939   (SOLVED)
electronics_engineering_ai999x.solve('elx_first_order_active_lowpass', R1=4700.0, Rf=47000.0, C=1e-08, f=500.0)
# -> H0 = -10, fc = 338.628 Hz, gain_f = 5.60755, gain_dB = 14.9755   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
First-order active low-pass filter: R1 = 10000 ohm, Rf = 100000 ohm, C = 1.59 nF, f = 1000 HzSOLVEDH0 = -10, fc = 1000.97 Hz, gain_f = 7.07451, gain_dB = 16.9939
First-order active low-pass filter: R1 = 4700 ohm, Rf = 47000 ohm, C = 10 nF, f = 500 HzSOLVEDH0 = -10, fc = 338.628 Hz, gain_f = 5.60755, gain_dB = 14.9755
First-order active low-pass filter: Rf = 100000 ohm, C = 1.59 nF, f = 1000 HzNEEDS_INPUTelx_first_order_active_lowpass needs R1 (input resistor). Example: solve('elx_first_order_active_lowpass', R1='10000 ohm
First-order active low-pass filter: R1 = 10000 ohm, Rf = 100000 ohm, C = 1.59 nF, f = 1000 Hz, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Sallen-Key low-pass filter: f0, Q and gain, elx_sallen_key_lowpass

The natural frequency, quality factor, passband gain and the gain at f0 (K Q) of a second-order Sallen-Key low-pass filter with any components and amplifier gain K.

\[\omega_0 = \frac{1}{\sqrt{R_1R_2C_1C_2}},\quad Q = \frac{\sqrt{R_1R_2C_1C_2}}{R_1C_2 + R_2C_2 + R_1C_1(1-K)}\]
inputmeaningcondition
R1first series resistor
R2second series resistor
C1capacitor from the middle node to the output (feedback)
C2capacitor from the amplifier input to ground
Kamplifier gain (1 for a unity-gain buffer)
outputmeaning
f0natural frequency
Qquality factor
H0passband gain
peak_gaingain at f0, K Q
Q against R1: Sallen-Key low-pass filter: f0, Q and gainQ (quality factor) against R1 (first series resistor), with C1 = 2.00e-8 F, C2 = 1.00e-8 F, K = 1, R2 = 10000 ohm. 31 points computed by electronics-engineering-ai999x; marked: R1 = 10000, Q = 0.707107.500075001000012500150000.670.680.690.70.710.707107 R1, first series resistor [ohm]Q
Q (quality factor) against R1 (first series resistor), with C1 = 2.00e-8 F, C2 = 1.00e-8 F, K = 1, R2 = 10000 ohm. 31 points computed by electronics-engineering-ai999x; marked: R1 = 10000, Q = 0.707107.
Sallen-Key low-pass filter: f0, Q and gain: quality factor against first series resistorQ (quality factor) against R1 (first series resistor) from 1000 ohm to 100000 ohm on a logarithmic axis. One curve for each value of K (amplifier gain (1 for a unity-gain buffer)): 1, 0.5, 2. Other inputs as in the worked example: R2 = 10000.0 ohm, C1 = 2e-08 F, C2 = 1e-08 F. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R1 = 10000 ohm, Q = 0.707107.1000100001.00e505100.707107K = 1 (example)K = 0.5K = 2R1 (first series resistor [ohm]Q), quality factor
Q (quality factor) against R1 (first series resistor) from 1000 ohm to 100000 ohm on a logarithmic axis. One curve for each value of K (amplifier gain (1 for a unity-gain buffer)): 1, 0.5, 2. Other inputs as in the worked example: R2 = 10000.0 ohm, C1 = 2e-08 F, C2 = 1e-08 F. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R1 = 10000 ohm, Q = 0.707107.
electronics_engineering_ai999x.solve('elx_sallen_key_lowpass', R1=10000.0, R2=10000.0, C1=2e-08, C2=1e-08, K=1.0)
# -> f0 = 1125.4 Hz, Q = 0.707107, H0 = 1, peak_gain = 0.707107   (SOLVED)
electronics_engineering_ai999x.solve('elx_sallen_key_lowpass', R1=15000.0, R2=15000.0, C1=1e-08, C2=1e-08, K=1.586)
# -> f0 = 1061.03 Hz, Q = 0.707214, H0 = 1.586, peak_gain = 1.12164   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Sallen-Key low-pass filter: R1 = 10000 ohm, R2 = 10000 ohm, C1 = 20 nF, C2 = 10 nF, K = 1SOLVEDf0 = 1125.4 Hz, Q = 0.707107, H0 = 1, peak_gain = 0.707107
Sallen-Key low-pass filter: R1 = 15000 ohm, R2 = 15000 ohm, C1 = 10 nF, C2 = 10 nF, K = 1.586SOLVEDf0 = 1061.03 Hz, Q = 0.707214, H0 = 1.586, peak_gain = 1.12164
Sallen-Key low-pass filter: R2 = 10000 ohm, C1 = 20 nF, C2 = 10 nF, K = 1NEEDS_INPUTelx_sallen_key_lowpass needs R1 (first series resistor). Example: solve('elx_sallen_key_lowpass', R1='10000 ohm', R2='10
Sallen-Key low-pass filter: R1 = 10000 ohm, R2 = 10000 ohm, C1 = 20 nF, C2 = 10 nF, K = 1, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Sallen-Key high-pass filter: f0, Q and gain, elx_sallen_key_highpass

The natural frequency, quality factor and high-frequency gain of a second-order Sallen-Key high-pass filter with any components and amplifier gain K.

\[Q = \frac{\sqrt{R_1R_2C_1C_2}}{R_1(C_1+C_2) + R_2C_2(1-K)}\]
inputmeaningcondition
C1first series capacitor
C2second series capacitor
R1resistor from the middle node to the output (feedback)
R2resistor from the amplifier input to ground
Kamplifier gain
outputmeaning
f0natural frequency
Qquality factor
H_infhigh-frequency gain
Sallen-Key high-pass filter: f0, Q and gain: quality factor against first series capacitorQ (quality factor) against C1 (first series capacitor) from 1.0000e-09 F to 1.0000e-07 F on a logarithmic axis. One curve for each value of K (amplifier gain): 1, 0.5, 2. Other inputs as in the worked example: C2 = 1e-08 F, R1 = 11250.0 ohm, R2 = 22500.0 ohm. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, C1 = 1.0000e-08 F, Q = 0.707107.1.00e-91.00e-81.00e-705100.707107K = 1 (example)K = 0.5K = 2C1 (first series capacitor [F]Q), quality factor
Q (quality factor) against C1 (first series capacitor) from 1.0000e-09 F to 1.0000e-07 F on a logarithmic axis. One curve for each value of K (amplifier gain): 1, 0.5, 2. Other inputs as in the worked example: C2 = 1e-08 F, R1 = 11250.0 ohm, R2 = 22500.0 ohm. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, C1 = 1.0000e-08 F, Q = 0.707107.
electronics_engineering_ai999x.solve('elx_sallen_key_highpass', C1=1e-08, C2=1e-08, R1=11250.0, R2=22500.0, K=1.0)
# -> f0 = 1000.35 Hz, Q = 0.707107, H_inf = 1   (SOLVED)
electronics_engineering_ai999x.solve('elx_sallen_key_highpass', C1=2.2e-08, C2=2.2e-08, R1=10000.0, R2=10000.0, K=2.0)
# -> f0 = 723.432 Hz, Q = 1, H_inf = 2   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Sallen-Key high-pass filter: C1 = 10 nF, C2 = 10 nF, R1 = 11250 ohm, R2 = 22500 ohm, K = 1SOLVEDf0 = 1000.35 Hz, Q = 0.707107, H_inf = 1
Sallen-Key high-pass filter: C1 = 22 nF, C2 = 22 nF, R1 = 10000 ohm, R2 = 10000 ohm, K = 2SOLVEDf0 = 723.432 Hz, Q = 1, H_inf = 2
Sallen-Key high-pass filter: C2 = 10 nF, R1 = 11250 ohm, R2 = 22500 ohm, K = 1NEEDS_INPUTelx_sallen_key_highpass needs C1 (first series capacitor). Example: solve('elx_sallen_key_highpass', C1='1e-08 F', C2='1
Sallen-Key high-pass filter: C1 = 10 nF, C2 = 10 nF, R1 = 11250 ohm, R2 = 22500 ohm, K = 1, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Multiple-feedback (MFB) low-pass filter, elx_mfb_lowpass

The natural frequency, quality factor and inverting passband gain -R2/R1 of a second-order multiple-feedback low-pass filter.

\[Q = \frac{\sqrt{R_2R_3C_1C_2}}{C_2\left(R_2 + R_3 + R_2R_3/R_1\right)},\quad H_0 = -\frac{R_2}{R_1}\]
inputmeaningcondition
R1input resistor
R2feedback resistor (middle node to output)
R3resistor from the middle node to the inverting input
C1capacitor from the middle node to ground
C2capacitor from the inverting input to the output
outputmeaning
f0natural frequency
Qquality factor
H0passband gain
Multiple-feedback (MFB) low-pass filter: quality factor against resistor from the middle node to the invert…Q (quality factor) against R3 (resistor from the middle node to the inverting input) from 500 ohm to 50000 ohm on a logarithmic axis. One curve for each value of C1 (capacitor from the middle node to ground): 4.7000e-08 F, 2.3500e-08 F, 9.4000e-08 F. Other inputs as in the worked example: R1 = 10000.0 ohm, R2 = 10000.0 ohm, C2 = 4.700000000000001e-09 F. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R3 = 5000 ohm, Q = 1.11803.1000100000.511.51.11803C1 = 4.7000e-08 F (example)C1 = 2.3500e-08 FC1 = 9.4000e-08 FR3 [ohm]Q, quality factor
Q (quality factor) against R3 (resistor from the middle node to the inverting input) from 500 ohm to 50000 ohm on a logarithmic axis. One curve for each value of C1 (capacitor from the middle node to ground): 4.7000e-08 F, 2.3500e-08 F, 9.4000e-08 F. Other inputs as in the worked example: R1 = 10000.0 ohm, R2 = 10000.0 ohm, C2 = 4.700000000000001e-09 F. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R3 = 5000 ohm, Q = 1.11803.
electronics_engineering_ai999x.solve('elx_mfb_lowpass', R1=10000.0, R2=10000.0, R3=5000.0, C1=4.7e-08, C2=4.7e-09)
# -> f0 = 1514.39 Hz, Q = 1.11803, H0 = -1   (SOLVED)
electronics_engineering_ai999x.solve('elx_mfb_lowpass', R1=4700.0, R2=47000.0, R3=10000.0, C1=1e-07, C2=1e-09)
# -> f0 = 734.127 Hz, Q = 1.38086, H0 = -10   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
MFB low-pass filter: R1 = 10000 ohm, R2 = 10000 ohm, R3 = 5000 ohm, C1 = 47 nF, C2 = 4.7 nFSOLVEDf0 = 1514.39 Hz, Q = 1.11803, H0 = -1
MFB low-pass filter: R1 = 4700 ohm, R2 = 47000 ohm, R3 = 10000 ohm, C1 = 100 nF, C2 = 1 nFSOLVEDf0 = 734.127 Hz, Q = 1.38086, H0 = -10
MFB low-pass filter: R2 = 10000 ohm, R3 = 5000 ohm, C1 = 47 nF, C2 = 4.7 nFNEEDS_INPUTelx_mfb_lowpass needs R1 (input resistor). Example: solve('elx_mfb_lowpass', R1='10000 ohm', R2='10000 ohm', R3='5000 oh
MFB low-pass filter: R1 = 10000 ohm, R2 = 10000 ohm, R3 = 5000 ohm, C1 = 47 nF, C2 = 4.7 nF, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Multiple-feedback (MFB) band-pass filter, elx_mfb_bandpass

The centre frequency, quality factor, -3 dB bandwidth and peak (inverting) gain of a multiple-feedback band-pass filter.

\[\omega_0 = \sqrt{\frac{R_1+R_2}{R_1R_2R_3C_1C_2}},\quad Q = \frac{\omega_0C_1C_2R_3}{C_1+C_2}\]
inputmeaningcondition
R1input resistor
R2resistor from the middle node to ground
R3feedback resistor (inverting input to output)
C1capacitor from the middle node to the inverting input
C2capacitor from the middle node to the output
outputmeaning
f0centre frequency
Qquality factor
BW-3 dB bandwidth
H_peakgain at the centre frequency
Multiple-feedback (MFB) band-pass filter: centre frequency against resistor from the middle node to groundf0 (centre frequency) against R2 (resistor from the middle node to ground) from 133 ohm to 13300 ohm on a logarithmic axis. One curve for each value of R3 (feedback resistor (inverting input to output)): 31800 ohm, 15900 ohm, 63600 ohm. Other inputs as in the worked example: R1 = 15900.0 ohm, C1 = 1e-08 F, C2 = 1e-08 F. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R2 = 1330 ohm, f0 = 2547.56 Hz.1000100000250050007500100002547.56 HzR3 = 31800 ohm (example)R3 = 15900 ohmR3 = 63600 ohmR2 [ohm]f0, centre frequency [Hz]
f0 (centre frequency) against R2 (resistor from the middle node to ground) from 133 ohm to 13300 ohm on a logarithmic axis. One curve for each value of R3 (feedback resistor (inverting input to output)): 31800 ohm, 15900 ohm, 63600 ohm. Other inputs as in the worked example: R1 = 15900.0 ohm, C1 = 1e-08 F, C2 = 1e-08 F. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R2 = 1330 ohm, f0 = 2547.56 Hz.
electronics_engineering_ai999x.solve('elx_mfb_bandpass', R1=15900.0, R2=1330.0, R3=31800.0, C1=1e-08, C2=1e-08)
# -> f0 = 2547.56 Hz, Q = 2.54508, BW = 1000.97 Hz, H_peak = -1   (SOLVED)
electronics_engineering_ai999x.solve('elx_mfb_bandpass', R1=10000.0, R2=470.0, R3=100000.0, C1=2.2e-08, C2=2.2e-08)
# -> f0 = 1079.75 Hz, Q = 7.46267, BW = 144.686 Hz, H_peak = -5   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
MFB band-pass filter: R1 = 15900 ohm, R2 = 1330 ohm, R3 = 31800 ohm, C1 = 10 nF, C2 = 10 nFSOLVEDf0 = 2547.56 Hz, Q = 2.54508, BW = 1000.97 Hz, H_peak = -1
MFB band-pass filter: R1 = 10000 ohm, R2 = 470 ohm, R3 = 100000 ohm, C1 = 22 nF, C2 = 22 nFSOLVEDf0 = 1079.75 Hz, Q = 7.46267, BW = 144.686 Hz, H_peak = -5
MFB band-pass filter: R2 = 1330 ohm, R3 = 31800 ohm, C1 = 10 nF, C2 = 10 nFNEEDS_INPUTelx_mfb_bandpass needs R1 (input resistor). Example: solve('elx_mfb_bandpass', R1='15900 ohm', R2='1330 ohm', R3='31800
MFB band-pass filter: R1 = 15900 ohm, R2 = 1330 ohm, R3 = 31800 ohm, C1 = 10 nF, C2 = 10 nF, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Equal-component Sallen-Key low-pass design, elx_sallen_key_equal_component_design

The resistor value and amplifier gain of an equal-component (R1 = R2 = R, C1 = C2 = C) Sallen-Key low-pass filter for a cutoff frequency and Q, with the non-inverting gain ratio $Rf/Rg = K - 1.$

\[R = \frac{1}{2\pi f_cC},\quad K = 3 - \frac{1}{Q}\]
inputmeaningcondition
fcnatural (cutoff) frequency
Qquality factor (0.7071 for Butterworth)
Cchosen capacitor value
outputmeaning
Rresistor value
Kamplifier gain
Rf_over_Rggain resistor ratio Rf/Rg
Equal-component Sallen-Key low-pass design: resistor value against natural (cutoff) frequencyR (resistor value) against fc (natural (cutoff) frequency) from 500 Hz to 1500 Hz. One curve for each value of C (chosen capacitor value): 1.0000e-08 F, 5.0000e-09 F, 2.0000e-08 F. Other inputs as in the worked example: Q = 0.7071. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, fc = 1000 Hz, R = 15915.5 ohm.50075010001250150020000400006000015915.5 ohmC = 1.0000e-08 F (example)C = 5.0000e-09 FC = 2.0000e-08 Ffc (natural (cutoff) frequency [Hz]R), resistor value [ohm]
R (resistor value) against fc (natural (cutoff) frequency) from 500 Hz to 1500 Hz. One curve for each value of C (chosen capacitor value): 1.0000e-08 F, 5.0000e-09 F, 2.0000e-08 F. Other inputs as in the worked example: Q = 0.7071. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, fc = 1000 Hz, R = 15915.5 ohm.
electronics_engineering_ai999x.solve('elx_sallen_key_equal_component_design', fc=1000.0, Q=0.7071, C=1e-08)
# -> R = 15915.5 ohm, K = 1.58577, Rf_over_Rg = 0.585773   (SOLVED)
electronics_engineering_ai999x.solve('elx_sallen_key_equal_component_design', fc=5000.0, Q=2.0, C=2.2e-09)
# -> R = 14468.6 ohm, K = 2.5, Rf_over_Rg = 1.5   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Equal-component Sallen-Key design: fc = 1000 Hz, Q = 0.7071, C = 10 nFSOLVEDR = 15915.5 ohm, K = 1.58577, Rf_over_Rg = 0.585773
Equal-component Sallen-Key design: fc = 5000 Hz, Q = 2, C = 2.2 nFSOLVEDR = 14468.6 ohm, K = 2.5, Rf_over_Rg = 1.5
Equal-component Sallen-Key design: Q = 0.7071, C = 10 nFNEEDS_INPUTelx_sallen_key_equal_component_design needs fc (natural (cutoff) frequency). Example: solve('elx_sallen_key_equal_compon
Equal-component Sallen-Key design: fc = 1000 Hz, Q = 0.7071, C = 10 nF, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Butterworth or Chebyshev low-pass filter order, elx_filter_order

The minimum order of a Butterworth or Chebyshev type I low-pass filter meeting a passband edge with at most Ap dB attenuation and a stopband edge with at least As dB.

\[n \ge \frac{\log_{10}D}{2\log_{10}(f_s/f_p)},\quad n \ge \frac{\cosh^{-1}\sqrt{D}}{\cosh^{-1}(f_s/f_p)}\]
inputmeaningcondition
ftypebutterworth or chebyshev (type I)
fppassband edge
fsstopband edge
Apmaximum passband attenuation (ripple) in dB
Asminimum stopband attenuation in dB
outputmeaning
nminimum filter order
Butterworth or Chebyshev low-pass filter order: minimum filter order against stopband edgen (minimum filter order) against fs (stopband edge) from 1250 Hz to 3750 Hz. One curve for each value of As (minimum stopband attenuation in dB): 40, 20, 80. Other inputs as in the worked example: ftype = Butterworth, fp = 1000.0 Hz, Ap = 1.0. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, fs = 2500 Hz, n = 6.200030000102030406As = 40 (example)As = 20As = 80fs (stopband edge [Hz]n), minimum filter order
n (minimum filter order) against fs (stopband edge) from 1250 Hz to 3750 Hz. One curve for each value of As (minimum stopband attenuation in dB): 40, 20, 80. Other inputs as in the worked example: ftype = Butterworth, fp = 1000.0 Hz, Ap = 1.0. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, fs = 2500 Hz, n = 6.
electronics_engineering_ai999x.solve('elx_filter_order', ftype='Butterworth', fp=1000.0, fs=2500.0, Ap=1.0, As=40.0)
# -> n = 6   (SOLVED)
electronics_engineering_ai999x.solve('elx_filter_order', ftype='Chebyshev', fp=1000.0, fs=2500.0, Ap=1.0, As=40.0)
# -> n = 4   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Filter order: ftype = Butterworth, fp = 1000 Hz, fs = 2500 Hz, Ap = 1 dB, As = 40 dBSOLVEDn = 6
Filter order: ftype = Chebyshev, fp = 1000 Hz, fs = 2500 Hz, Ap = 1 dB, As = 40 dBSOLVEDn = 4
Filter order: fp = 1000 Hz, fs = 2500 Hz, Ap = 1 dB, As = 40 dBNEEDS_INPUTelx_filter_order needs ftype (butterworth or chebyshev (type I)). Example: solve('elx_filter_order', ftype='Butterworth'
Filter order: ftype = Butterworth, fp = 1000 Hz, fs = 2500 Hz, Ap = 1 dB, As = 40 dB, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te
Filter order: type = Butterworth, fp = 1 kHz, fs = 2.5 kHz, Ap = 1 dB, As = 40 dBSOLVEDn = 6
Filter order: ftype = butterworth, fp = 1 kHz, fs = 2.5 kHz, Ap = 1, As = 40 dBUNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Butterworth filter: Q of each second-order section, elx_butterworth_section_q

The quality factors of the cascaded second-order sections of an n-th order Butterworth filter (all at the cutoff frequency), and whether a first-order section is needed.

\[Q_k = \frac{1}{2\sin\left(\frac{(2k-1)\pi}{2n}\right)}\]
inputmeaningcondition
nfilter order
outputmeaning
Q_maxlargest section Q
Qsection Q values, ascending
sectionsnumber of second-order sections
first_order1 if a first-order section is needed
Butterworth filter: Q of each second-order section: largest section Q against filter orderQ_max (largest section Q) against n (filter order) from 1 to 12. 11 points computed by electronics-engineering-ai999x; marked: the worked example, n = 4, Q_max = 1.30656.2.557.51012.5012341.30656n (filter orderQ_max), largest section Q
Q_max (largest section Q) against n (filter order) from 1 to 12. 11 points computed by electronics-engineering-ai999x; marked: the worked example, n = 4, Q_max = 1.30656.
electronics_engineering_ai999x.solve('elx_butterworth_section_q', n=4)
# -> Q_max = 1.30656, Q = [0.541196100146, 1.30656296488], sections = 2, first_order = 0   (SOLVED)
electronics_engineering_ai999x.solve('elx_butterworth_section_q', n=5)
# -> Q_max = 1.61803, Q = [0.61803398875, 1.61803398875], sections = 2, first_order = 1   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Butterworth section Q: n = 4SOLVEDQ_max = 1.30656, Q = [0.541196100146, 1.30656296488], sections = 2, first_order = 0
Butterworth section Q: n = 5SOLVEDQ_max = 1.61803, Q = [0.61803398875, 1.61803398875], sections = 2, first_order = 1
Butterworth section Q: NEEDS_INPUTelx_butterworth_section_q needs n (filter order). Example: solve('elx_butterworth_section_q', n=4).
Butterworth section Q: n = 4, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Chebyshev type I filter: section Q and frequencies, elx_chebyshev_sections

The quality factors and natural frequencies (relative to the passband edge) of the second-order sections of an n-th order Chebyshev type I low-pass filter with a given passband ripple, and the real pole of an odd order.

\[p_k = -\sinh a\sin\theta_k + j\cosh a\cos\theta_k,\ a = \frac{1}{n}\sinh^{-1}\frac{1}{\varepsilon},\ Q_k = \frac{|p_k|}{2|\Re p_k|}\]
inputmeaningcondition
nfilter order
ripplepassband ripple in dB
outputmeaning
Q_maxlargest section Q
Qsection Q values, ascending
f0_ratiosection natural frequencies / passband edge, in the same order
sectionsnumber of second-order sections
real_polereal pole / passband edge (0 for even n)
Chebyshev type I filter: section Q and frequencies: f0_ratio at each Qsection natural frequencies / passband edge, in the same order (f0_ratio) at each section Q values, ascending (Q), both returned by electronics-engineering-ai999x for the worked example (n = 4, ripple = 0.5): 0.70511 → 0.597002; 2.94055 → 1.03127.11.522.500.250.50.751(0.70511, 0.597002)(2.94055, 1.03127)Q, section Q values, ascendingf0_ratio
section natural frequencies / passband edge, in the same order (f0_ratio) at each section Q values, ascending (Q), both returned by electronics-engineering-ai999x for the worked example (n = 4, ripple = 0.5): 0.70511 → 0.597002; 2.94055 → 1.03127.
Chebyshev type I filter: section Q and frequencies: largest section Q against passband ripple in dBQ_max (largest section Q) against ripple (passband ripple in dB) from 0.05 to 5 on a logarithmic axis. One curve for each value of n (filter order): 4, 2, 8. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, ripple = 0.5, Q_max = 2.94055.0.1101020302.94055n = 4 (example)n = 2n = 8ripple (passband ripple in dBQ_max), largest section Q
Q_max (largest section Q) against ripple (passband ripple in dB) from 0.05 to 5 on a logarithmic axis. One curve for each value of n (filter order): 4, 2, 8. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, ripple = 0.5, Q_max = 2.94055.
electronics_engineering_ai999x.solve('elx_chebyshev_sections', n=4, ripple=0.5)
# -> Q_max = 2.94055, Q = [0.705110236803, 2.94055417439], f0_ratio = [0.59700239512, 1.03127040148], sections = 2, real_pole = 0   (SOLVED)
electronics_engineering_ai999x.solve('elx_chebyshev_sections', n=3, ripple=1.0)
# -> Q_max = 2.01772, Q = [2.01772034366], f0_ratio = [0.997098082833], sections = 1, real_pole = 0.494171   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Chebyshev filter sections: n = 4, ripple = 0.5 dBSOLVEDQ_max = 2.94055, Q = [0.705110236803, 2.94055417439], f0_ratio = [0.59700239512, 1.03127040148], sections = 2, real_pole = 0
Chebyshev filter sections: n = 3, ripple = 1 dBSOLVEDQ_max = 2.01772, Q = [2.01772034366], f0_ratio = [0.997098082833], sections = 1, real_pole = 0.494171
Chebyshev filter sections: ripple = 0.5 dBNEEDS_INPUTelx_chebyshev_sections needs n (filter order). Example: solve('elx_chebyshev_sections', n=4, ripple=0.5).
Chebyshev filter sections: n = 4, ripple = 0.5 dB, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

RC phase-shift oscillator frequency and gain, elx_rc_phase_shift_oscillator

The oscillation frequency of a three-section RC phase-shift oscillator (high-pass ladder: series C, shunt R; or low-pass ladder) and the amplifier gain of 29 it needs.

\[f_0 = \frac{1}{2\pi\sqrt{6}\,RC},\quad |A| \ge 29\]
inputmeaningcondition
Rresistor of each section
Ccapacitor of each section
ladderhighpass (series C, shunt R) or lowpass (series R, shunt C)
outputmeaning
f0oscillation frequency
A_minminimum inverting amplifier gain
betafeedback network attenuation at f0
RC phase-shift oscillator frequency and gain: oscillation frequency against resistor of each sectionf0 (oscillation frequency) against R (resistor of each section) from 5000 ohm to 15000 ohm. One curve for each value of C (capacitor of each section): 1.0000e-08 F, 5.0000e-09 F, 2.0000e-08 F. Other inputs as in the worked example: ladder = high-pass. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R = 10000 ohm, f0 = 649.747 Hz.5000750010000125001500010002000649.747 HzC = 1.0000e-08 F (example)C = 5.0000e-09 FC = 2.0000e-08 FR (resistor of each section [ohm]f0), oscillation frequency [Hz]
f0 (oscillation frequency) against R (resistor of each section) from 5000 ohm to 15000 ohm. One curve for each value of C (capacitor of each section): 1.0000e-08 F, 5.0000e-09 F, 2.0000e-08 F. Other inputs as in the worked example: ladder = high-pass. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R = 10000 ohm, f0 = 649.747 Hz.
RC phase-shift oscillator frequency and gain: oscillation frequency over resistor of each section and capac…f0 (oscillation frequency) over R (resistor of each section) from 5000 ohm to 15000 ohm and C (capacitor of each section) from 5.0000e-09 F to 1.5000e-08 F: each of the 21 × 15 cells is one run of electronics-engineering-ai999x, shaded by its value (light 288.777 Hz to dark 2598.99 Hz); iso-lines at f0 = 500, 1000, 1500, 2000 Hz. Other inputs as in the worked example: ladder = high-pass. Marked: the worked example, R = 10000 ohm, C = 1.0000e-08 F, f0 = 649.747 Hz.500075001000012500150005.00e-97.50e-91.00e-81.25e-81.50e-8500100015002000649.747 Hz2598.99288.777f0R (resistor of each section [ohm]C), capacitor of each section [F]
f0 (oscillation frequency) over R (resistor of each section) from 5000 ohm to 15000 ohm and C (capacitor of each section) from 5.0000e-09 F to 1.5000e-08 F: each of the 21 × 15 cells is one run of electronics-engineering-ai999x, shaded by its value (light 288.777 Hz to dark 2598.99 Hz); iso-lines at f0 = 500, 1000, 1500, 2000 Hz. Other inputs as in the worked example: ladder = high-pass. Marked: the worked example, R = 10000 ohm, C = 1.0000e-08 F, f0 = 649.747 Hz.
electronics_engineering_ai999x.solve('elx_rc_phase_shift_oscillator', R=10000.0, C=1e-08, ladder='high-pass')
# -> f0 = 649.747 Hz, A_min = 29, beta = 0.0344828   (SOLVED)
electronics_engineering_ai999x.solve('elx_rc_phase_shift_oscillator', R=4700.0, C=4.7e-08, ladder='low-pass')
# -> f0 = 1764.82 Hz, A_min = 29, beta = 0.0344828   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
RC phase-shift oscillator: R = 10000 ohm, C = 10 nF, ladder = high-passSOLVEDf0 = 649.747 Hz, A_min = 29, beta = 0.0344828
RC phase-shift oscillator: R = 4700 ohm, C = 47 nF, ladder = low-passSOLVEDf0 = 1764.82 Hz, A_min = 29, beta = 0.0344828
RC phase-shift oscillator: C = 10 nF, ladder = high-passNEEDS_INPUTelx_rc_phase_shift_oscillator needs R (resistor of each section). Example: solve('elx_rc_phase_shift_oscillator', R='100
RC phase-shift oscillator: R = 10000 ohm, C = 10 nF, ladder = high-pass, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Wien-bridge oscillator frequency and required gain, elx_wien_bridge_oscillator

The oscillation frequency of a Wien-bridge oscillator (series R1 C1, parallel R2 C2) and the non-inverting gain it needs (3 for equal components).

\[f_0 = \frac{1}{2\pi\sqrt{R_1R_2C_1C_2}},\quad A = 1 + \frac{R_1}{R_2} + \frac{C_2}{C_1}\]
inputmeaningcondition
R1series-arm resistor
C1series-arm capacitor
R2parallel-arm resistor
C2parallel-arm capacitor
outputmeaning
f0oscillation frequency
betafeedback fraction at f0
A_minrequired amplifier gain
Rf_over_Rggain resistor ratio
Wien-bridge oscillator frequency and required gain: oscillation frequency against series-arm resistorf0 (oscillation frequency) against R1 (series-arm resistor) from 5000 ohm to 15000 ohm. One curve for each value of C1 (series-arm capacitor): 1.6000e-08 F, 8.0000e-09 F, 3.2000e-08 F. Other inputs as in the worked example: R2 = 10000.0 ohm, C2 = 1.6e-08 F. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R1 = 10000 ohm, f0 = 994.718 Hz.50007500100001250015000500100015002000994.718 HzC1 = 1.6000e-08 F (example)C1 = 8.0000e-09 FC1 = 3.2000e-08 FR1 (series-arm resistor [ohm]f0), oscillation frequency [Hz]
f0 (oscillation frequency) against R1 (series-arm resistor) from 5000 ohm to 15000 ohm. One curve for each value of C1 (series-arm capacitor): 1.6000e-08 F, 8.0000e-09 F, 3.2000e-08 F. Other inputs as in the worked example: R2 = 10000.0 ohm, C2 = 1.6e-08 F. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R1 = 10000 ohm, f0 = 994.718 Hz.
electronics_engineering_ai999x.solve('elx_wien_bridge_oscillator', R1=10000.0, C1=1.6e-08, R2=10000.0, C2=1.6e-08)
# -> f0 = 994.718 Hz, beta = 0.333333, A_min = 3, Rf_over_Rg = 2   (SOLVED)
electronics_engineering_ai999x.solve('elx_wien_bridge_oscillator', R1=22000.0, C1=1e-08, R2=10000.0, C2=2.2e-08)
# -> f0 = 723.432 Hz, beta = 0.185185, A_min = 5.4, Rf_over_Rg = 4.4   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Wien-bridge oscillator: R1 = 10000 ohm, C1 = 16 nF, R2 = 10000 ohm, C2 = 16 nFSOLVEDf0 = 994.718 Hz, beta = 0.333333, A_min = 3, Rf_over_Rg = 2
Wien-bridge oscillator: R1 = 22000 ohm, C1 = 10 nF, R2 = 10000 ohm, C2 = 22 nFSOLVEDf0 = 723.432 Hz, beta = 0.185185, A_min = 5.4, Rf_over_Rg = 4.4
Wien-bridge oscillator: C1 = 16 nF, R2 = 10000 ohm, C2 = 16 nFNEEDS_INPUTelx_wien_bridge_oscillator needs R1 (series-arm resistor). Example: solve('elx_wien_bridge_oscillator', R1='10000 ohm',
Wien-bridge oscillator: R1 = 10000 ohm, C1 = 16 nF, R2 = 10000 ohm, C2 = 16 nF, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Colpitts oscillator frequency and feedback ratio, elx_colpitts_oscillator

The oscillation frequency of a Colpitts oscillator from its inductor and the series combination of its two tank capacitors, the feedback fraction $C_{1}/C_{2}$ and the minimum amplifier gain $C_{2}/C_{1}.$

\[f_0 = \frac{1}{2\pi\sqrt{L\,\frac{C_1C_2}{C_1+C_2}}},\quad A_{min} = \frac{C_2}{C_1}\]
inputmeaningcondition
Ltank inductance
C1capacitor across the amplifier output
C2capacitor across the amplifier input (feedback side)
outputmeaning
C_eqseries equivalent capacitance
f0oscillation frequency
betafeedback fraction $C_{1}/C_{2}$
A_minminimum amplifier gain $C_{2}/C_{1}$
Colpitts oscillator frequency and feedback ratio: oscillation frequency against capacitor across the amplif…f0 (oscillation frequency) against C1 (capacitor across the amplifier output) from 1.0000e-10 F to 1.0000e-08 F on a logarithmic axis. One curve for each value of L (tank inductance): 1.0000e-04 H, 5.0000e-05 H, 0.0002 H. Other inputs as in the worked example: C2 = 1e-08 F. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, C1 = 1.0000e-09 F, f0 = 527857 Hz.1.00e-101.00e-91.00e-805.00e51.00e61.50e62.00e6527857 HzL = 1.0000e-04 H (example)L = 5.0000e-05 HL = 0.0002 HC1 [F]f0, oscillation frequency [Hz]
f0 (oscillation frequency) against C1 (capacitor across the amplifier output) from 1.0000e-10 F to 1.0000e-08 F on a logarithmic axis. One curve for each value of L (tank inductance): 1.0000e-04 H, 5.0000e-05 H, 0.0002 H. Other inputs as in the worked example: C2 = 1e-08 F. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, C1 = 1.0000e-09 F, f0 = 527857 Hz.
electronics_engineering_ai999x.solve('elx_colpitts_oscillator', L=0.0001, C1=1e-09, C2=1e-08)
# -> C_eq = 9.09091e-10 F, f0 = 527857 Hz, beta = 0.1, A_min = 10   (SOLVED)
electronics_engineering_ai999x.solve('elx_colpitts_oscillator', L=1e-05, C1=4.7e-10, C2=4.7e-09)
# -> C_eq = 4.27273e-10 F, f0 = 2.43482e+06 Hz, beta = 0.1, A_min = 10   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Colpitts oscillator: L = 100 uH, C1 = 1 nF, C2 = 10 nFSOLVEDC_eq = 9.09091e-10 F, f0 = 527857 Hz, beta = 0.1, A_min = 10
Colpitts oscillator: L = 10 uH, C1 = 0.47 nF, C2 = 4.7 nFSOLVEDC_eq = 4.27273e-10 F, f0 = 2.43482e+06 Hz, beta = 0.1, A_min = 10
Colpitts oscillator: C1 = 1 nF, C2 = 10 nFNEEDS_INPUTelx_colpitts_oscillator needs L (tank inductance). Example: solve('elx_colpitts_oscillator', L='0.0001 H', C1='1e-09 F',
Colpitts oscillator: L = 100 uH, C1 = 1 nF, C2 = 10 nF, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Hartley oscillator frequency, elx_hartley_oscillator

The oscillation frequency of a Hartley oscillator with a tapped (or two coupled) inductors and a tank capacitor, and the gain ratio $(L_{1} + M)/(L_{2} + M)$.

\[f_0 = \frac{1}{2\pi\sqrt{(L_1 + L_2 + 2M)C}}\]
inputmeaningcondition
L1inductance of the output-side coil
L2inductance of the feedback-side coil
Mmutual inductance (0 for uncoupled coils)
Ctank capacitance
outputmeaning
L_eqtotal inductance $L_{1} + L_{2} + 2M$
f0oscillation frequency
A_minminimum amplifier gain $(L_{1} + M)/(L_{2} + M)$
Hartley oscillator frequency: oscillation frequency against tank capacitancef0 (oscillation frequency) against C (tank capacitance) from 5.0000e-10 F to 1.5000e-09 F. One curve for each value of L1 (inductance of the output-side coil): 1.0000e-04 H, 5.0000e-05 H, 0.0002 H. Other inputs as in the worked example: L2 = 1.9999999999999998e-05 H, M = 0.0 H. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, C = 1.0000e-09 F, f0 = 459441 Hz.5.00e-107.50e-101.00e-91.25e-91.50e-94.00e56.00e58.00e5459441 HzL1 = 1.0000e-04 H (example)L1 = 5.0000e-05 HL1 = 0.0002 HC (tank capacitance [F]f0), oscillation frequency [Hz]
f0 (oscillation frequency) against C (tank capacitance) from 5.0000e-10 F to 1.5000e-09 F. One curve for each value of L1 (inductance of the output-side coil): 1.0000e-04 H, 5.0000e-05 H, 0.0002 H. Other inputs as in the worked example: L2 = 1.9999999999999998e-05 H, M = 0.0 H. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, C = 1.0000e-09 F, f0 = 459441 Hz.
electronics_engineering_ai999x.solve('elx_hartley_oscillator', L1=0.0001, L2=2e-05, M=0.0, C=1e-09)
# -> L_eq = 0.00012 H, f0 = 459441 Hz, A_min = 5   (SOLVED)
electronics_engineering_ai999x.solve('elx_hartley_oscillator', L1=5e-05, L2=1e-05, M=5e-06, C=4.7e-10)
# -> L_eq = 7e-05 H, f0 = 877450 Hz, A_min = 3.66667   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Hartley oscillator: L1 = 100 uH, L2 = 20 uH, M = 0 uH, C = 1 nFSOLVEDL_eq = 0.00012 H, f0 = 459441 Hz, A_min = 5
Hartley oscillator: L1 = 50 uH, L2 = 10 uH, M = 5 uH, C = 0.47 nFSOLVEDL_eq = 7e-05 H, f0 = 877450 Hz, A_min = 3.66667
Hartley oscillator: L2 = 20 uH, M = 0 uH, C = 1 nFNEEDS_INPUTelx_hartley_oscillator needs L1 (inductance of the output-side coil). Example: solve('elx_hartley_oscillator', L1='0.000
Hartley oscillator: L1 = 100 uH, L2 = 20 uH, M = 0 uH, C = 1 nF, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Quartz crystal: series and parallel resonance, Q, elx_crystal_oscillator

The series and parallel (anti-) resonant frequencies, their spacing and the quality factor of a quartz crystal from its Butterworth-Van Dyke equivalent circuit.

\[f_s = \frac{1}{2\pi\sqrt{L_mC_m}},\quad f_p = f_s\sqrt{1 + \frac{C_m}{C_0}}\]
inputmeaningcondition
Lmmotional inductance
Cmmotional capacitance
Rmmotional resistance
C0shunt (holder) capacitance
outputmeaning
fsseries resonance
fpparallel resonance
delta_ffp - fs
Qquality factor
Quartz crystal: series and parallel resonance, Q: series resonance against motional inductancefs (series resonance) against Lm (motional inductance) from 0.025 H to 0.075 H. One curve for each value of Cm (motional capacitance): 2.0000e-14 F, 1.0000e-14 F, 4.0000e-14 F. Other inputs as in the worked example: Rm = 20.0 ohm, C0 = 5e-12 F. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Lm = 0.05 H, fs = 5.03292e+06 Hz.0.040.064.00e66.00e68.00e61.00e75.03292e+06 HzCm = 2.0000e-14 F (example)Cm = 1.0000e-14 FCm = 4.0000e-14 FLm (motional inductance [H]fs), series resonance [Hz]
fs (series resonance) against Lm (motional inductance) from 0.025 H to 0.075 H. One curve for each value of Cm (motional capacitance): 2.0000e-14 F, 1.0000e-14 F, 4.0000e-14 F. Other inputs as in the worked example: Rm = 20.0 ohm, C0 = 5e-12 F. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Lm = 0.05 H, fs = 5.03292e+06 Hz.
electronics_engineering_ai999x.solve('elx_crystal_oscillator', Lm=0.05, Cm=2e-14, Rm=20.0, C0=5e-12)
# -> fs = 5.03292e+06 Hz, fp = 5.04298e+06 Hz, delta_f = 10055.8 Hz, Q = 79056.9   (SOLVED)
electronics_engineering_ai999x.solve('elx_crystal_oscillator', Lm=0.26, Cm=2.5e-14, Rm=50.0, C0=6e-12)
# -> fs = 1.97407e+06 Hz, fp = 1.97818e+06 Hz, delta_f = 4108.38 Hz, Q = 64498.1   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Crystal resonance: Lm = 0.05 H, Cm = 20 fF, Rm = 20 ohm, C0 = 5 pFSOLVEDfs = 5.03292e+06 Hz, fp = 5.04298e+06 Hz, delta_f = 10055.8 Hz, Q = 79056.9
Crystal resonance: Lm = 0.26 H, Cm = 25 fF, Rm = 50 ohm, C0 = 6 pFSOLVEDfs = 1.97407e+06 Hz, fp = 1.97818e+06 Hz, delta_f = 4108.38 Hz, Q = 64498.1
Crystal resonance: Cm = 20 fF, Rm = 20 ohm, C0 = 5 pFNEEDS_INPUTelx_crystal_oscillator needs Lm (motional inductance). Example: solve('elx_crystal_oscillator', Lm='0.05 H', Cm='2e-14 F
Crystal resonance: Lm = 0.05 H, Cm = 20 fF, Rm = 20 ohm, C0 = 5 pF, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Op-amp relaxation (astable) oscillator, elx_opamp_relaxation_oscillator

The period and frequency of a square-wave op-amp astable: an RC timing network on the inverting input and positive feedback $R_{1}/(R_{1} + R_{2})$ to the non-inverting input, symmetric supplies.

\[T = 2RC\ln\frac{1+\beta}{1-\beta},\quad \beta = \frac{R_1}{R_1+R_2}\]
inputmeaningcondition
Rtiming resistor (output to inverting input)
Ctiming capacitor
R1resistor from the + input to ground
R2resistor from the output to the + input
outputmeaning
betafeedback fraction $R_{1}/(R_{1} + R_{2})$
Tperiod
ffrequency
Op-amp relaxation (astable) oscillator: frequency against resistor from the + input to groundf (frequency) against R1 (resistor from the + input to ground) from 1000 ohm to 100000 ohm on a logarithmic axis. One curve for each value of R (timing resistor (output to inverting input)): 10000 ohm, 5000 ohm, 20000 ohm. Other inputs as in the worked example: C = 1.0000000000000001e-07 F, R2 = 10000.0 ohm. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R1 = 10000 ohm, f = 455.12 Hz.1000100001.00e5020004000455.12 HzR = 10000 ohm (example)R = 5000 ohmR = 20000 ohmR1 [ohm]f, frequency [Hz]
f (frequency) against R1 (resistor from the + input to ground) from 1000 ohm to 100000 ohm on a logarithmic axis. One curve for each value of R (timing resistor (output to inverting input)): 10000 ohm, 5000 ohm, 20000 ohm. Other inputs as in the worked example: C = 1.0000000000000001e-07 F, R2 = 10000.0 ohm. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R1 = 10000 ohm, f = 455.12 Hz.
electronics_engineering_ai999x.solve('elx_opamp_relaxation_oscillator', R=10000.0, C=1e-07, R1=10000.0, R2=10000.0)
# -> beta = 0.5, T = 0.00219722 s, f = 455.12 Hz   (SOLVED)
electronics_engineering_ai999x.solve('elx_opamp_relaxation_oscillator', R=47000.0, C=1e-08, R1=8600.0, R2=10000.0)
# -> beta = 0.462366, T = 0.000940594 s, f = 1063.16 Hz   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Op-amp relaxation oscillator: R = 10000 ohm, C = 100 nF, R1 = 10000 ohm, R2 = 10000 ohmSOLVEDbeta = 0.5, T = 0.00219722 s, f = 455.12 Hz
Op-amp relaxation oscillator: R = 47000 ohm, C = 10 nF, R1 = 8600 ohm, R2 = 10000 ohmSOLVEDbeta = 0.462366, T = 0.000940594 s, f = 1063.16 Hz
Op-amp relaxation oscillator: C = 100 nF, R1 = 10000 ohm, R2 = 10000 ohmNEEDS_INPUTelx_opamp_relaxation_oscillator needs R (timing resistor (output to inverting input)). Example: solve('elx_opamp_relaxat
Op-amp relaxation oscillator: R = 10000 ohm, C = 100 nF, R1 = 10000 ohm, R2 = 10000 ohm, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

555 timer astable: frequency and duty cycle, elx_555_astable

The high and low times, period, frequency and duty cycle of a 555 timer in astable mode with resistors RA and RB and timing capacitor C.

\[t_H = \ln 2\,(R_A + R_B)C,\quad t_L = \ln 2\,R_BC,\quad f = \frac{1}{\ln 2\,(R_A + 2R_B)C}\]
inputmeaningcondition
RAresistor from Vcc to the discharge pin
RBresistor from discharge to threshold/trigger
Ctiming capacitor
outputmeaning
t_highoutput high time
t_lowoutput low time
Tperiod
ffrequency
dutyduty cycle (fraction high)
f against RA: 555 timer astable: frequency and duty cyclef (frequency) against RA (resistor from Vcc to the discharge pin), with C = 1.00e-5 F, RB = 10000 ohm. 31 points computed by electronics-engineering-ai999x; marked: RA = 1000, f = 6.86998 Hz.5007501000125015006.76.86.976.86998 HzRA, resistor from Vcc to the discharge pin [ohm]f [Hz]
f (frequency) against RA (resistor from Vcc to the discharge pin), with C = 1.00e-5 F, RB = 10000 ohm. 31 points computed by electronics-engineering-ai999x; marked: RA = 1000, f = 6.86998 Hz.
555 timer astable: frequency and duty cycle: frequency against resistor from discharge to threshold/triggerf (frequency) against RB (resistor from discharge to threshold/trigger) from 1000 ohm to 100000 ohm on a logarithmic axis. One curve for each value of C (timing capacitor): 1.0000e-05 F, 5.0000e-06 F, 2.0000e-05 F. Other inputs as in the worked example: RA = 1000.0 ohm. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, RB = 10000 ohm, f = 6.86998 Hz.1000100001.00e502550751006.86998 HzC = 1.0000e-05 F (example)C = 5.0000e-06 FC = 2.0000e-05 FRB [ohm]f, frequency [Hz]
f (frequency) against RB (resistor from discharge to threshold/trigger) from 1000 ohm to 100000 ohm on a logarithmic axis. One curve for each value of C (timing capacitor): 1.0000e-05 F, 5.0000e-06 F, 2.0000e-05 F. Other inputs as in the worked example: RA = 1000.0 ohm. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, RB = 10000 ohm, f = 6.86998 Hz.
electronics_engineering_ai999x.solve('elx_555_astable', RA=1000.0, RB=10000.0, C=1e-05)
# -> t_high = 0.0762462 s, t_low = 0.0693147 s, T = 0.145561 s, f = 6.86998 Hz, duty = 0.52381   (SOLVED)
electronics_engineering_ai999x.solve('elx_555_astable', RA=4700.0, RB=4700.0, C=1e-07)
# -> t_high = 0.000651558 s, t_low = 0.000325779 s, T = 0.000977338 s, f = 1023.19 Hz, duty = 0.666667   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
555 astable: RA = 1000 ohm, RB = 10000 ohm, C = 10 uFSOLVEDt_high = 0.0762462 s, t_low = 0.0693147 s, T = 0.145561 s, f = 6.86998 Hz, duty = 0.52381
555 astable: RA = 4700 ohm, RB = 4700 ohm, C = 0.1 uFSOLVEDt_high = 0.000651558 s, t_low = 0.000325779 s, T = 0.000977338 s, f = 1023.19 Hz, duty = 0.666667
555 astable: RB = 10000 ohm, C = 10 uFNEEDS_INPUTelx_555_astable needs RA (resistor from Vcc to the discharge pin). Example: solve('elx_555_astable', RA='1000 ohm', RB='
555 astable: RA = 1000 ohm, RB = 10000 ohm, C = 10 uF, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

555 timer monostable pulse width, elx_555_monostable

The output pulse width $T = ln$ 3 R C (about 1.1 R C) of a 555 timer in monostable (one-shot) mode.

\[T = \ln 3\,RC \approx 1.1\,RC\]
inputmeaningcondition
Rtiming resistor
Ctiming capacitor
outputmeaning
Tpulse width
555 timer monostable pulse width: pulse width against timing resistorT (pulse width) against R (timing resistor) from 50000 ohm to 150000 ohm. One curve for each value of C (timing capacitor): 1.0000e-05 F, 5.0000e-06 F, 2.0000e-05 F. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R = 100000 ohm, T = 1.09861 s.50000750001.00e51.25e51.50e51231.09861 sC = 1.0000e-05 F (example)C = 5.0000e-06 FC = 2.0000e-05 FR (timing resistor [ohm]T), pulse width [s]
T (pulse width) against R (timing resistor) from 50000 ohm to 150000 ohm. One curve for each value of C (timing capacitor): 1.0000e-05 F, 5.0000e-06 F, 2.0000e-05 F. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R = 100000 ohm, T = 1.09861 s.
555 timer monostable pulse width: pulse width over timing resistor and timing capacitorT (pulse width) over R (timing resistor) from 50000 ohm to 150000 ohm and C (timing capacitor) from 5.0000e-06 F to 1.5000e-05 F: each of the 21 × 15 cells is one run of electronics-engineering-ai999x, shaded by its value (light 0.274653 s to dark 2.47188 s); iso-lines at T = 0.5, 1, 1.5, 2 s. Marked: the worked example, R = 100000 ohm, C = 1.0000e-05 F, T = 1.09861 s.50000750001.00e51.25e51.50e55.00e-67.50e-61.00e-51.25e-51.50e-50.511.521.09861 s2.471880.274653TR (timing resistor [ohm]C), timing capacitor [F]
T (pulse width) over R (timing resistor) from 50000 ohm to 150000 ohm and C (timing capacitor) from 5.0000e-06 F to 1.5000e-05 F: each of the 21 × 15 cells is one run of electronics-engineering-ai999x, shaded by its value (light 0.274653 s to dark 2.47188 s); iso-lines at T = 0.5, 1, 1.5, 2 s. Marked: the worked example, R = 100000 ohm, C = 1.0000e-05 F, T = 1.09861 s.
electronics_engineering_ai999x.solve('elx_555_monostable', R=100000.0, C=1e-05)
# -> T = 1.09861 s   (SOLVED)
electronics_engineering_ai999x.solve('elx_555_monostable', R=47000.0, C=1e-06)
# -> T = 0.0516348 s   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
555 monostable: R = 100000 ohm, C = 10 uFSOLVEDT = 1.09861 s
555 monostable: R = 47000 ohm, C = 1 uFSOLVEDT = 0.0516348 s
555 monostable: C = 10 uFNEEDS_INPUTelx_555_monostable needs R (timing resistor). Example: solve('elx_555_monostable', R='100000 ohm', C='1e-05 F').
555 monostable: R = 100000 ohm, C = 10 uF, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Type-2 PLL with active PI loop filter: natural frequency and damping, elx_pll_loop_dynamics

The natural frequency and damping factor of a second-order (type-2) phase-locked loop with phase-detector gain Kd, VCO gain Ko and an active PI loop filter F($s) = (1 + s$ $tau2)/(s$ tau1).

\[\omega_n = \sqrt{\frac{K_dK_o}{\tau_1}},\quad \zeta = \frac{\tau_2\omega_n}{2}\]
inputmeaningcondition
Kdphase-detector gain in V/rad
KoVCO gain in rad/(s V)
tau1integrator time constant R1 C
tau2zero time constant R2 C
outputmeaning
wnnatural frequency
fnnatural frequency in Hz
zetadamping factor
Type-2 PLL with active PI loop filter: natural frequency and damping: damping factor against integrator tim…zeta (damping factor) against tau1 (integrator time constant R1 C) from 0.005 s to 0.015 s. One curve for each value of tau2 (zero time constant R2 C): 0.001 s, 0.0005 s, 0.002 s. Other inputs as in the worked example: Kd = 0.5, Ko = 20000.0. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, tau1 = 0.01 s, zeta = 0.5.0.0050.00750.010.01250.0150.511.50.5tau2 = 0.001 s (example)tau2 = 0.0005 stau2 = 0.002 stau1 (integrator time constant R1 C [s]zeta), damping factor
zeta (damping factor) against tau1 (integrator time constant R1 C) from 0.005 s to 0.015 s. One curve for each value of tau2 (zero time constant R2 C): 0.001 s, 0.0005 s, 0.002 s. Other inputs as in the worked example: Kd = 0.5, Ko = 20000.0. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, tau1 = 0.01 s, zeta = 0.5.
electronics_engineering_ai999x.solve('elx_pll_loop_dynamics', Kd=0.5, Ko=20000.0, tau1=0.01, tau2=0.001)
# -> wn = 1000 rad/s, fn = 159.155 Hz, zeta = 0.5   (SOLVED)
electronics_engineering_ai999x.solve('elx_pll_loop_dynamics', Kd=1.0, Ko=100000.0, tau1=0.1, tau2=0.002)
# -> wn = 1000 rad/s, fn = 159.155 Hz, zeta = 1   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
PLL loop dynamics: Kd = 0.5 V/rad, Ko = 20000 rad/(s*V), tau1 = 10 ms, tau2 = 1 msSOLVEDwn = 1000 rad/s, fn = 159.155 Hz, zeta = 0.5
PLL loop dynamics: Kd = 1 V/rad, Ko = 100000 rad/(s*V), tau1 = 100 ms, tau2 = 2 msSOLVEDwn = 1000 rad/s, fn = 159.155 Hz, zeta = 1
PLL loop dynamics: Ko = 20000 rad/(s*V), tau1 = 10 ms, tau2 = 1 msNEEDS_INPUTelx_pll_loop_dynamics needs Kd (phase-detector gain in V/rad). Example: solve('elx_pll_loop_dynamics', Kd=0.5, Ko=20000,
PLL loop dynamics: Kd = 0.5 V/rad, Ko = 20000 rad/(s*V), tau1 = 10 ms, tau2 = 1 ms, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

ADC output code, LSB and quantisation error, elx_adc_code

The output code (decimal and binary) of an ideal unipolar truncating n-bit ADC for an input voltage, the LSB size, the voltage the code represents and the quantisation error.

\[D = \left\lfloor \frac{V_{in}}{V_{ref}}2^n\right\rfloor,\quad \text{LSB} = \frac{V_{ref}}{2^n}\]
inputmeaningcondition
Vinanalog input
Vrefreference (full-scale) voltage
nresolution in bits
outputmeaning
codeoutput code (decimal)
bitsoutput code in binary
LSBLSB = Vref/2^n
V_codevoltage of the code
errorquantisation error Vin - code LSB
code against Vin: ADC output code, LSB and quantisation errorcode (output code (decimal)) against Vin (analog input), with Vref = 5 V, n = 8. 31 points computed by electronics-engineering-ai999x; marked: Vin = 3.2, code = 163.234100150200250163 Vin, analog input [V]code
code (output code (decimal)) against Vin (analog input), with Vref = 5 V, n = 8. 31 points computed by electronics-engineering-ai999x; marked: Vin = 3.2, code = 163.
ADC output code, LSB and quantisation error: output code (decimal) against resolution in bitscode (output code (decimal)) against n (resolution in bits) from 1 to 16, logarithmic output axis. Other inputs as in the worked example: Vin = 3.2 V, Vref = 5.0 V. 16 points computed by electronics-engineering-ai999x; marked: the worked example, n = 8, code = 163.51015110100100010000163n (resolution in bitscode), output code (decimal)
code (output code (decimal)) against n (resolution in bits) from 1 to 16, logarithmic output axis. Other inputs as in the worked example: Vin = 3.2 V, Vref = 5.0 V. 16 points computed by electronics-engineering-ai999x; marked: the worked example, n = 8, code = 163.
electronics_engineering_ai999x.solve('elx_adc_code', Vin=3.2, Vref=5.0, n=8)
# -> code = 163, bits = 10100011, LSB = 0.0195312 V, V_code = 3.18359 V, error = 0.0164063 V   (SOLVED)
electronics_engineering_ai999x.solve('elx_adc_code', Vin=1.234, Vref=2.5, n=12)
# -> code = 2021, bits = 011111100101, LSB = 0.000610352 V, V_code = 1.23352 V, error = 0.000479492 V   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
ADC output code: Vin = 3.2 V, Vref = 5 V, n = 8SOLVEDcode = 163, bits = 10100011, LSB = 0.0195312 V, V_code = 3.18359 V, error = 0.0164063 V
ADC output code: Vin = 1.234 V, Vref = 2.5 V, n = 12SOLVEDcode = 2021, bits = 011111100101, LSB = 0.000610352 V, V_code = 1.23352 V, error = 0.000479492 V
ADC output code: Vref = 5 V, n = 8NEEDS_INPUTelx_adc_code needs Vin (analog input). Example: solve('elx_adc_code', Vin='3.2 V', Vref='5 V', n=8).
ADC output code: Vin = 3.2 V, Vref = 5 V, n = 8, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

ADC quantisation SNR with oversampling, elx_adc_quantization_snr

The signal-to-quantisation-noise ratio of an ideal n-bit converter for a sine input (6.02 $n + 1.76$ dB at full scale), with an oversampling ratio and a reduced amplitude, and the in-band noise in LSB.

\[\text{SNR} = 6.02\,n + 1.76 + 10\log_{10}\text{OSR}\ \text{dB}\]
inputmeaningcondition
nresolution in bits
OSRoversampling ratio (default 1)
A_fracsine amplitude as a fraction of full scale (default 1)
outputmeaning
SNR_dBsignal-to-quantisation-noise ratio, dB
noise_rms_lsbin-band noise rms in LSB
SNR_full_scale_dBfull-scale SNR without oversampling, dB
ADC quantisation SNR with oversampling: signal-to-quantisation-noise ratio, dB against resolution in bitsSNR_dB (signal-to-quantisation-noise ratio, dB) against n (resolution in bits) from 1 to 24. 24 points computed by electronics-engineering-ai999x; marked: the worked example, n = 12, SNR_dB = 74.0081.0102005010015074.0081n (resolution in bitsSNR_dB), signal-to-quantisation-noise ratio
SNR_dB (signal-to-quantisation-noise ratio, dB) against n (resolution in bits) from 1 to 24. 24 points computed by electronics-engineering-ai999x; marked: the worked example, n = 12, SNR_dB = 74.0081.
electronics_engineering_ai999x.solve('elx_adc_quantization_snr', n=12)
# -> SNR_dB = 74.0081, noise_rms_lsb = 0.288675, SNR_full_scale_dB = 74.0081   (SOLVED)
electronics_engineering_ai999x.solve('elx_adc_quantization_snr', n=10, OSR=16.0, A_frac=0.5)
# -> SNR_dB = 67.9875, noise_rms_lsb = 0.0721688, SNR_full_scale_dB = 61.9669   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
ADC quantization SNR: n = 12SOLVEDSNR_dB = 74.0081, noise_rms_lsb = 0.288675, SNR_full_scale_dB = 74.0081
ADC quantization SNR: n = 10, OSR = 16, A_frac = 0.5SOLVEDSNR_dB = 67.9875, noise_rms_lsb = 0.0721688, SNR_full_scale_dB = 61.9669
ADC quantization SNR: NEEDS_INPUTelx_adc_quantization_snr needs n (resolution in bits). Example: solve('elx_adc_quantization_snr', n=12).
ADC quantization SNR: n = 12, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Effective number of bits (ENOB) from SINAD, elx_adc_enob

The effective number of bits of a converter from its measured SINAD (IEEE 1241: ENOB = (SINAD - 1.76)/6.02) and the bits lost against its nominal resolution.

\[\text{ENOB} = \frac{\text{SINAD} - 1.76}{6.02}\]
inputmeaningcondition
SINADsignal to noise and distortion ratio in dB
nnominal resolution in bits
outputmeaning
ENOBeffective number of bits
bits_lostn - ENOB
Effective number of bits (ENOB) from SINAD: effective number of bits against signal to noise and distortion…ENOB (effective number of bits) against SINAD (signal to noise and distortion ratio in dB) from 37 to 111. Other inputs as in the worked example: n = 14. 31 points computed by electronics-engineering-ai999x; marked: the worked example, SINAD = 74, ENOB = 12.4060801005101512SINADENOB, effective number of bits
ENOB (effective number of bits) against SINAD (signal to noise and distortion ratio in dB) from 37 to 111. Other inputs as in the worked example: n = 14. 31 points computed by electronics-engineering-ai999x; marked: the worked example, SINAD = 74, ENOB = 12.
electronics_engineering_ai999x.solve('elx_adc_enob', SINAD=74.0, n=14)
# -> ENOB = 12, bits_lost = 2   (SOLVED)
electronics_engineering_ai999x.solve('elx_adc_enob', SINAD=62.5, n=12)
# -> ENOB = 10.0897, bits_lost = 1.9103   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
ADC ENOB: SINAD = 74 dB, n = 14SOLVEDENOB = 12, bits_lost = 2
ADC ENOB: SINAD = 62.5 dB, n = 12SOLVEDENOB = 10.0897, bits_lost = 1.9103
ADC ENOB: n = 14NEEDS_INPUTelx_adc_enob needs SINAD (signal to noise and distortion ratio in dB). Example: solve('elx_adc_enob', SINAD=74, n=14).
ADC ENOB: SINAD = 74 dB, n = 14, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

SNR limit from sampling-clock (aperture) jitter, elx_aperture_jitter_snr

The SNR limit -20 log10(2 pi f tj) set by rms sampling-clock jitter for a full-scale sine, combined with the quantisation SNR of an n-bit converter into a total SNR and effective bits.

\[\text{SNR}_j = -20\log_{10}(2\pi f t_j)\]
inputmeaningcondition
finput frequency
tjrms clock jitter
nconverter resolution in bits
outputmeaning
SNR_jitter_dBjitter-limited SNR, dB
SNR_quant_dBquantisation SNR, dB
SNR_total_dBcombined SNR, dB
ENOB_totaleffective bits of the combination
SNR limit from sampling-clock (aperture) jitter: jitter-limited SNR, dB against input frequencySNR_jitter_dB (jitter-limited SNR, dB) against f (input frequency) from 1.0000e+07 Hz to 1.0000e+09 Hz on a logarithmic axis. One curve for each value of tj (rms clock jitter): 1.0000e-12 s, 5.0000e-13 s, 2.0000e-12 s. Other inputs as in the worked example: n = 14. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, f = 1.0000e+08 Hz, SNR_jitter_dB = 64.0364.1.00e71.00e81.00e940608064.0364tj = 1.0000e-12 s (example)tj = 5.0000e-13 stj = 2.0000e-12 sf (input frequency [Hz]SNR_jitter_dB), jitter-limited SNR, dB
SNR_jitter_dB (jitter-limited SNR, dB) against f (input frequency) from 1.0000e+07 Hz to 1.0000e+09 Hz on a logarithmic axis. One curve for each value of tj (rms clock jitter): 1.0000e-12 s, 5.0000e-13 s, 2.0000e-12 s. Other inputs as in the worked example: n = 14. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, f = 1.0000e+08 Hz, SNR_jitter_dB = 64.0364.
electronics_engineering_ai999x.solve('elx_aperture_jitter_snr', f=100000000.0, tj=1e-12, n=14)
# -> SNR_jitter_dB = 64.0364, SNR_quant_dB = 86.0493, SNR_total_dB = 64.0092, ENOB_total = 10.3404   (SOLVED)
electronics_engineering_ai999x.solve('elx_aperture_jitter_snr', f=10000000.0, tj=5e-13, n=16)
# -> SNR_jitter_dB = 90.057, SNR_quant_dB = 98.0905, SNR_total_dB = 89.4227, ENOB_total = 14.5619   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Aperture jitter SNR: f = 100000000 Hz, tj = 1 ps, n = 14SOLVEDSNR_jitter_dB = 64.0364, SNR_quant_dB = 86.0493, SNR_total_dB = 64.0092, ENOB_total = 10.3404
Aperture jitter SNR: f = 10000000 Hz, tj = 0.5 ps, n = 16SOLVEDSNR_jitter_dB = 90.057, SNR_quant_dB = 98.0905, SNR_total_dB = 89.4227, ENOB_total = 14.5619
Aperture jitter SNR: tj = 1 ps, n = 14NEEDS_INPUTelx_aperture_jitter_snr needs f (input frequency). Example: solve('elx_aperture_jitter_snr', f='1e+08 Hz', tj='1e-12 s',
Aperture jitter SNR: f = 100000000 Hz, tj = 1 ps, n = 14, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

DAC output voltage (R-2R or any binary DAC), elx_dac_output

The output voltage of an ideal n-bit unipolar DAC for a code, Vout = Vref $D/2^{n}$, its step size and its full-scale output.

\[V_{out} = V_{ref}\frac{D}{2^n}\]
inputmeaningcondition
nresolution in bits
codeinput code (decimal)
Vrefreference voltage
outputmeaning
Voutoutput voltage
LSBstep size Vref/2^n
V_full_scaleoutput for the all-ones code
DAC output voltage (R-2R or any binary DAC): output voltage against input code (decimal)Vout (output voltage) against code (input code (decimal)) from 1 to 400 on a logarithmic axis. One curve for each value of Vref (reference voltage): 5 V, 2.5 V, 10 V. Other inputs as in the worked example: n = 8. 32 points per curve computed by electronics-engineering-ai999x; marked: the worked example, code = 200, Vout = 3.90625 V.11010002.557.5103.90625 VVref = 5 V (example)Vref = 2.5 VVref = 10 Vcode (input code (decimal)Vout), output voltage [V]
Vout (output voltage) against code (input code (decimal)) from 1 to 400 on a logarithmic axis. One curve for each value of Vref (reference voltage): 5 V, 2.5 V, 10 V. Other inputs as in the worked example: n = 8. 32 points per curve computed by electronics-engineering-ai999x; marked: the worked example, code = 200, Vout = 3.90625 V.
electronics_engineering_ai999x.solve('elx_dac_output', n=8, code=200, Vref=5.0)
# -> Vout = 3.90625 V, LSB = 0.0195312 V, V_full_scale = 4.98047 V   (SOLVED)
electronics_engineering_ai999x.solve('elx_dac_output', n=4, code=11, Vref=10.0)
# -> Vout = 6.875 V, LSB = 0.625 V, V_full_scale = 9.375 V   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
DAC output voltage: n = 8, code = 200, Vref = 5 VSOLVEDVout = 3.90625 V, LSB = 0.0195312 V, V_full_scale = 4.98047 V
DAC output voltage: n = 4, code = 11, Vref = 10 VSOLVEDVout = 6.875 V, LSB = 0.625 V, V_full_scale = 9.375 V
DAC output voltage: code = 200, Vref = 5 VNEEDS_INPUTelx_dac_output needs n (resolution in bits). Example: solve('elx_dac_output', n=8, code=200, Vref='5 V').
DAC output voltage: n = 8, code = 200, Vref = 5 V, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Binary-weighted resistor DAC, elx_dac_binary_weighted

The output voltage and summing current of a binary-weighted resistor DAC with an inverting op-amp (MSB resistor R, each lower bit doubling it) and the largest resistor needed.

\[V_{out} = -V_{ref}\frac{R_f}{R}\sum_{k=0}^{n-1}\frac{b_k}{2^k} = -V_{ref}\frac{R_f}{R}\frac{D}{2^{n-1}}\]
inputmeaningcondition
nresolution in bits
codeinput code (decimal)
Vrefreference voltage
RMSB resistor
Rffeedback resistor
outputmeaning
Voutoutput voltage
I_totaltotal current into the summing node
R_LSBLSB resistor R $2^{n-1}$
Binary-weighted resistor DAC: output voltage against MSB resistorVout (output voltage) against R (MSB resistor) from 1000 ohm to 100000 ohm on a logarithmic axis. One curve for each value of Vref (reference voltage): 5 V, 2.5 V, 10 V. Other inputs as in the worked example: n = 4, code = 10, Rf = 5000.0 ohm. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R = 10000 ohm, Vout = -3.125 V.1000100001.00e5-60-40-200-3.125 VVref = 5 V (example)Vref = 2.5 VVref = 10 VR (MSB resistor [ohm]Vout), output voltage [V]
Vout (output voltage) against R (MSB resistor) from 1000 ohm to 100000 ohm on a logarithmic axis. One curve for each value of Vref (reference voltage): 5 V, 2.5 V, 10 V. Other inputs as in the worked example: n = 4, code = 10, Rf = 5000.0 ohm. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R = 10000 ohm, Vout = -3.125 V.
electronics_engineering_ai999x.solve('elx_dac_binary_weighted', n=4, code=10, Vref=5.0, R=10000.0, Rf=5000.0)
# -> Vout = -3.125 V, I_total = 0.000625 A, R_LSB = 80000 ohm   (SOLVED)
electronics_engineering_ai999x.solve('elx_dac_binary_weighted', n=8, code=129, Vref=2.5, R=1000.0, Rf=1000.0)
# -> Vout = -2.51953 V, I_total = 0.00251953 A, R_LSB = 128000 ohm   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Binary-weighted DAC: n = 4, code = 10, Vref = 5 V, R = 10000 ohm, Rf = 5000 ohmSOLVEDVout = -3.125 V, I_total = 0.000625 A, R_LSB = 80000 ohm
Binary-weighted DAC: n = 8, code = 129, Vref = 2.5 V, R = 1000 ohm, Rf = 1000 ohmSOLVEDVout = -2.51953 V, I_total = 0.00251953 A, R_LSB = 128000 ohm
Binary-weighted DAC: code = 10, Vref = 5 V, R = 10000 ohm, Rf = 5000 ohmNEEDS_INPUTelx_dac_binary_weighted needs n (resolution in bits). Example: solve('elx_dac_binary_weighted', n=4, code=10, Vref='5 V'
Binary-weighted DAC: n = 4, code = 10, Vref = 5 V, R = 10000 ohm, Rf = 5000 ohm, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Successive-approximation (SAR) ADC conversion, elx_sar_conversion

The bit-by-bit trial voltages, the final code (decimal and binary) and the DAC voltage of an ideal n-bit successive-approximation ADC converting an input.

\[b_k = \left[V_{in} \ge V_{DAC}(D_{k} + 2^k)\right]\]
inputmeaningcondition
Vinanalog input
Vrefreference voltage
nresolution in bits
outputmeaning
codefinal code
bitsfinal code in binary
trialstrial DAC voltages, MSB first (V)
V_dacDAC voltage of the final code
cyclescomparison cycles
Successive-approximation (SAR) ADC conversion: trial DAC voltages, MSB first (V)trial DAC voltages, MSB first (V) (trials) returned by electronics-engineering-ai999x for the worked example, one value for each position in the list (4 values, first 2.5, last 3.4375, largest 3.75). Inputs: Vin = 3.2 V, Vref = 5.0 V, n = 4.123401234position in the listtrials, trial DAC voltages, MSB first (V)
trial DAC voltages, MSB first (V) (trials) returned by electronics-engineering-ai999x for the worked example, one value for each position in the list (4 values, first 2.5, last 3.4375, largest 3.75). Inputs: Vin = 3.2 V, Vref = 5.0 V, n = 4.
Successive-approximation (SAR) ADC conversion: final code against reference voltagecode (final code) against Vref (reference voltage) from 2.5 V to 7.5 V. One curve for each value of n (resolution in bits): 4, 2, 8. Other inputs as in the worked example: Vin = 3.2 V. 26 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Vref = 5 V, code = 10.4567010020010n = 4 (example)n = 2n = 8Vref (reference voltage [V]code), final code
code (final code) against Vref (reference voltage) from 2.5 V to 7.5 V. One curve for each value of n (resolution in bits): 4, 2, 8. Other inputs as in the worked example: Vin = 3.2 V. 26 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Vref = 5 V, code = 10.
electronics_engineering_ai999x.solve('elx_sar_conversion', Vin=3.2, Vref=5.0, n=4)
# -> code = 10, bits = 1010, trials = [2.5, 3.75, 3.125, 3.4375], V_dac = 3.125 V, cycles = 4   (SOLVED)
electronics_engineering_ai999x.solve('elx_sar_conversion', Vin=1.7, Vref=3.3, n=8)
# -> code = 131, bits = 10000011, trials = [1.65, 2.475, 2.0625, 1.85625, 1.753125, 1.7015625, 1.67578125, 1.688671875], V_dac = 1.68867 V, cycles = 8   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
SAR ADC conversion: Vin = 3.2 V, Vref = 5 V, n = 4SOLVEDcode = 10, bits = 1010, trials = [2.5, 3.75, 3.125, 3.4375], V_dac = 3.125 V, cycles = 4
SAR ADC conversion: Vin = 1.7 V, Vref = 3.3 V, n = 8SOLVEDcode = 131, bits = 10000011, trials = [1.65, 2.475, 2.0625, 1.85625, 1.753125, 1.7015625, 1.67578125, 1.688671875], V_dac = 1.68867 V, cycles = 8
SAR ADC conversion: Vref = 5 V, n = 4NEEDS_INPUTelx_sar_conversion needs Vin (analog input). Example: solve('elx_sar_conversion', Vin='3.2 V', Vref='5 V', n=4).
SAR ADC conversion: Vin = 3.2 V, Vref = 5 V, n = 4, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Dual-slope integrating ADC, elx_dual_slope_adc

The fixed integration time, the de-integration time and count, and the peak integrator voltage of a dual-slope ADC.

\[T_2 = T_1\frac{V_{in}}{V_{ref}},\quad N_2 = N_1\frac{V_{in}}{V_{ref}}\]
inputmeaningcondition
Vininput voltage (magnitude)
Vrefreference voltage (magnitude)
N1fixed count of the integration phase
fclkclock frequency
Rintegrator resistor
Cintegrator capacitor
outputmeaning
T1integration time N1/fclk
T2de-integration time
N2count of the de-integration phase (unrounded)
V_peakpeak integrator output
Dual-slope integrating ADC: de-integration time against clock frequencyT2 (de-integration time) against fclk (clock frequency) from 50000 Hz to 150000 Hz. One curve for each value of N1 (fixed count of the integration phase): 1000, 500, 2000. Other inputs as in the worked example: Vin = 0.5 V, Vref = 1.0 V, R = 100000.0 ohm, C = 1e-07 F. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, fclk = 100000 Hz, T2 = 0.005 s.50000750001.00e51.25e51.50e50.0050.010.0150.020.005 sN1 = 1000 (example)N1 = 500N1 = 2000fclk (clock frequency [Hz]T2), de-integration time [s]
T2 (de-integration time) against fclk (clock frequency) from 50000 Hz to 150000 Hz. One curve for each value of N1 (fixed count of the integration phase): 1000, 500, 2000. Other inputs as in the worked example: Vin = 0.5 V, Vref = 1.0 V, R = 100000.0 ohm, C = 1e-07 F. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, fclk = 100000 Hz, T2 = 0.005 s.
electronics_engineering_ai999x.solve('elx_dual_slope_adc', Vin=0.5, Vref=1.0, N1=1000, fclk=100000.0, R=100000.0, C=1e-07)
# -> T1 = 0.01 s, T2 = 0.005 s, N2 = 500, V_peak = 0.5 V   (SOLVED)
electronics_engineering_ai999x.solve('elx_dual_slope_adc', Vin=1.234, Vref=2.0, N1=2000, fclk=1000000.0, R=47000.0, C=2.2e-07)
# -> T1 = 0.002 s, T2 = 0.001234 s, N2 = 1234, V_peak = 0.238685 V   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Dual-slope ADC: Vin = 0.5 V, Vref = 1 V, N1 = 1000, fclk = 100000 Hz, R = 100000 ohm, C = 0.1 uFSOLVEDT1 = 0.01 s, T2 = 0.005 s, N2 = 500, V_peak = 0.5 V
Dual-slope ADC: Vin = 1.234 V, Vref = 2 V, N1 = 2000, fclk = 1000000 Hz, R = 47000 ohm, C = 0.22 uFSOLVEDT1 = 0.002 s, T2 = 0.001234 s, N2 = 1234, V_peak = 0.238685 V
Dual-slope ADC: Vref = 1 V, N1 = 1000, fclk = 100000 Hz, R = 100000 ohm, C = 0.1 uFNEEDS_INPUTelx_dual_slope_adc needs Vin (input voltage (magnitude)). Example: solve('elx_dual_slope_adc', Vin='0.5 V', Vref='1 V',
Dual-slope ADC: Vin = 0.5 V, Vref = 1 V, N1 = 1000, fclk = 100000 Hz, R = 100000 ohm, C = 0.1 uF, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Sample-and-hold droop, elx_sample_hold_droop

The droop rate I/C of a sample-and-hold capacitor discharged by a leakage current, the droop over a hold time (in volts and LSB) and the longest hold that keeps the droop within half an LSB of an n-bit converter.

\[\frac{dV}{dt} = \frac{I_{leak}}{C}\]
inputmeaningcondition
I_leakleakage (bias) current
Chold capacitor
t_holdhold time
Vrefconverter full scale
nconverter resolution in bits
outputmeaning
droop_ratedroop rate I/C
droopdroop over the hold time
droop_lsbdroop in LSB
t_max_half_lsblongest hold for half an LSB
Sample-and-hold droop: droop over the hold time against hold capacitordroop (droop over the hold time) against C (hold capacitor) from 5.0000e-10 F to 1.5000e-09 F. One curve for each value of I_leak (leakage (bias) current): 1.0000e-09 A, 5.0000e-10 A, 2.0000e-09 A. Other inputs as in the worked example: t_hold = 9.999999999999999e-06 s, Vref = 5.0 V, n = 12. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, C = 1.0000e-09 F, droop = 1.0000e-05 V.5.00e-107.50e-101.00e-91.25e-91.50e-91.00e-52.00e-53.00e-54.00e-51.0000e-05 VI_leak = 1.0000e-09 A (example)I_leak = 5.0000e-10 AI_leak = 2.0000e-09 AC (hold capacitor [F]droop), droop over the hold time [V]
droop (droop over the hold time) against C (hold capacitor) from 5.0000e-10 F to 1.5000e-09 F. One curve for each value of I_leak (leakage (bias) current): 1.0000e-09 A, 5.0000e-10 A, 2.0000e-09 A. Other inputs as in the worked example: t_hold = 9.999999999999999e-06 s, Vref = 5.0 V, n = 12. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, C = 1.0000e-09 F, droop = 1.0000e-05 V.
electronics_engineering_ai999x.solve('elx_sample_hold_droop', I_leak=1e-09, C=1e-09, t_hold=1e-05, Vref=5.0, n=12)
# -> droop_rate = 1 V/s, droop = 1e-05 V, droop_lsb = 0.008192, t_max_half_lsb = 0.000610352 s   (SOLVED)
electronics_engineering_ai999x.solve('elx_sample_hold_droop', I_leak=5e-11, C=1e-10, t_hold=2e-05, Vref=10.0, n=16)
# -> droop_rate = 0.5 V/s, droop = 1e-05 V, droop_lsb = 0.065536, t_max_half_lsb = 0.000152588 s   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Sample-and-hold droop: I_leak = 1 nA, C = 1 nF, t_hold = 10 us, Vref = 5 V, n = 12SOLVEDdroop_rate = 1 V/s, droop = 1e-05 V, droop_lsb = 0.008192, t_max_half_lsb = 0.000610352 s
Sample-and-hold droop: I_leak = 0.05 nA, C = 0.1 nF, t_hold = 20 us, Vref = 10 V, n = 16SOLVEDdroop_rate = 0.5 V/s, droop = 1e-05 V, droop_lsb = 0.065536, t_max_half_lsb = 0.000152588 s
Sample-and-hold droop: C = 1 nF, t_hold = 10 us, Vref = 5 V, n = 12NEEDS_INPUTelx_sample_hold_droop needs I_leak (leakage (bias) current). Example: solve('elx_sample_hold_droop', I_leak='1e-09 A', C
Sample-and-hold droop: I_leak = 1 nA, C = 1 nF, t_hold = 10 us, Vref = 5 V, n = 12, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

RC delay, 10-90 % rise time and bandwidth, elx_rc_delay_rise_time

The time constant, the 50 % delay (ln 2 RC), the $10-90$ % rise time (ln 9 $RC = 2.2$ RC), the -3 dB bandwidth and the rise-time-bandwidth product (0.35) of a first-order RC low-pass.

\[t_r = \ln 9\,RC \approx 2.2RC,\quad t_rf_{3dB} \approx 0.35\]
inputmeaningcondition
Rresistance
Ccapacitance
outputmeaning
tautime constant RC
t5050 % delay
t_rise$10-90$ % rise time
f_3dB-3 dB bandwidth
tr_times_bwrise time x bandwidth
RC delay, 10-90 % rise time and bandwidth: 10-90 % rise time against resistancet_rise (10-90 % rise time) against R (resistance) from 500 ohm to 1500 ohm. One curve for each value of C (capacitance): 1.0000e-11 F, 5.0000e-12 F, 2.0000e-11 F. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R = 1000 ohm, t_rise = 2.1972e-08 s.5007501000125015002.00e-84.00e-86.00e-82.1972e-08 sC = 1.0000e-11 F (example)C = 5.0000e-12 FC = 2.0000e-11 FR (resistance [ohm]t_rise), 10-90 % rise time [s]
t_rise (10-90 % rise time) against R (resistance) from 500 ohm to 1500 ohm. One curve for each value of C (capacitance): 1.0000e-11 F, 5.0000e-12 F, 2.0000e-11 F. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R = 1000 ohm, t_rise = 2.1972e-08 s.
RC delay, 10-90 % rise time and bandwidth: 10-90 % rise time over resistance and capacitancet_rise (10-90 % rise time) over R (resistance) from 500 ohm to 1500 ohm and C (capacitance) from 5.0000e-12 F to 1.5000e-11 F: each of the 21 × 15 cells is one run of electronics-engineering-ai999x, shaded by its value (light 5.4931e-09 s to dark 4.9438e-08 s); iso-lines at t_rise = 1.00e-8, 2.00e-8, 3.00e-8, 4.00e-8 s. Marked: the worked example, R = 1000 ohm, C = 1.0000e-11 F, t_rise = 2.1972e-08 s.5007501000125015005.00e-127.50e-121.00e-111.25e-111.50e-111.00e-82.00e-83.00e-84.00e-82.1972e-08 s4.94e-85.49e-9t_riseR (resistance [ohm]C), capacitance [F]
t_rise (10-90 % rise time) over R (resistance) from 500 ohm to 1500 ohm and C (capacitance) from 5.0000e-12 F to 1.5000e-11 F: each of the 21 × 15 cells is one run of electronics-engineering-ai999x, shaded by its value (light 5.4931e-09 s to dark 4.9438e-08 s); iso-lines at t_rise = 1.00e-8, 2.00e-8, 3.00e-8, 4.00e-8 s. Marked: the worked example, R = 1000 ohm, C = 1.0000e-11 F, t_rise = 2.1972e-08 s.
electronics_engineering_ai999x.solve('elx_rc_delay_rise_time', R=1000.0, C=1e-11)
# -> tau = 1e-08 s, t50 = 6.93147e-09 s, t_rise = 2.19722e-08 s, f_3dB = 1.59155e+07 Hz, tr_times_bw = 0.349699   (SOLVED)
electronics_engineering_ai999x.solve('elx_rc_delay_rise_time', R=50.0, C=1e-10)
# -> tau = 5e-09 s, t50 = 3.46574e-09 s, t_rise = 1.09861e-08 s, f_3dB = 3.1831e+07 Hz, tr_times_bw = 0.349699   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
RC delay and rise time: R = 1000 ohm, C = 10 pFSOLVEDtau = 1e-08 s, t50 = 6.93147e-09 s, t_rise = 2.19722e-08 s, f_3dB = 1.59155e+07 Hz, tr_times_bw = 0.349699
RC delay and rise time: R = 50 ohm, C = 100 pFSOLVEDtau = 5e-09 s, t50 = 3.46574e-09 s, t_rise = 1.09861e-08 s, f_3dB = 3.1831e+07 Hz, tr_times_bw = 0.349699
RC delay and rise time: C = 10 pFNEEDS_INPUTelx_rc_delay_rise_time needs R (resistance). Example: solve('elx_rc_delay_rise_time', R='1000 ohm', C='1e-11 F').
RC delay and rise time: R = 1000 ohm, C = 10 pF, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Elmore delay of an RC ladder (interconnect), elx_elmore_delay

The Elmore delay to every node of an RC ladder (a driver resistance and wire segments, each followed by a capacitance to ground), the delay at the far end and its 50 % estimate ln 2 tau.

\[\tau_D = \sum_i C_i\sum_{j\le i}R_j\]
inputmeaningcondition
Rseries resistances in ohms, from the driver outwards
Cnode capacitances in picofarads, one after each resistor
outputmeaning
tau_DElmore delay at the far end
t5050 % delay estimate ln 2 tau_D
delaysElmore delay at each node, seconds
Elmore delay of an RC ladder (interconnect): Elmore delay at each node, secondsElmore delay at each node, seconds (delays) returned by electronics-engineering-ai999x for the worked example, one value for each position in the list (3 values, first 4.0000e-11, last 6.5000e-11, largest 6.5000e-11). Inputs: R = [100.0, 50.0, 50.0], C = [0.1, 0.1, 0.2].12302.00e-114.00e-116.00e-11position in the listdelays, Elmore delay at each node, seconds
Elmore delay at each node, seconds (delays) returned by electronics-engineering-ai999x for the worked example, one value for each position in the list (3 values, first 4.0000e-11, last 6.5000e-11, largest 6.5000e-11). Inputs: R = [100.0, 50.0, 50.0], C = [0.1, 0.1, 0.2].
electronics_engineering_ai999x.solve('elx_elmore_delay', R=[100.0, 50.0, 50.0], C=[0.1, 0.1, 0.2])
# -> tau_D = 6.5e-11 s, t50 = 4.50546e-11 s, delays = [4e-11, 5.5e-11, 6.5e-11]   (SOLVED)
electronics_engineering_ai999x.solve('elx_elmore_delay', R=[1000.0, 200.0], C=[0.05, 0.5])
# -> tau_D = 6.5e-10 s, t50 = 4.50546e-10 s, delays = [5.5e-10, 6.5e-10]   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Elmore delay: R = [100, 50, 50], C = [0.1, 0.1, 0.2]SOLVEDtau_D = 6.5e-11 s, t50 = 4.50546e-11 s, delays = [4e-11, 5.5e-11, 6.5e-11]
Elmore delay: R = [1000, 200], C = [0.05, 0.5]SOLVEDtau_D = 6.5e-10 s, t50 = 4.50546e-10 s, delays = [5.5e-10, 6.5e-10]
Elmore delay: C = [0.1, 0.1, 0.2]NEEDS_INPUTelx_elmore_delay needs R (series resistances in ohms, from the driver outwards). Example: solve('elx_elmore_delay', R=[1
Elmore delay: R = [100, 50, 50], C = [0.1, 0.1, 0.2], zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

CMOS dynamic (switching) power, elx_cmos_dynamic_power

The dynamic power alpha C VDD^2 f of CMOS logic, the energy drawn from the supply per 0 -> 1 transition, the energy stored on the load and the average supply current.

\[P_{dyn} = \alpha\,C\,V_{DD}^2f\]
inputmeaningcondition
alphaactivity factor: probability of a 0 -> 1 transition per clock cycle
Cswitched capacitance
VDDsupply voltage
fclock frequency
outputmeaning
Pdynamic power
E_supplyenergy from the supply per transition, C VDD^2
E_storedenergy stored on C, C VDD^2/2
I_avgaverage supply current
CMOS dynamic (switching) power: dynamic power against supply voltageP (dynamic power) against VDD (supply voltage) from 0.5 V to 1.5 V. One curve for each value of C (switched capacitance): 1.0000e-09 F, 5.0000e-10 F, 2.0000e-09 F. Other inputs as in the worked example: alpha = 0.1, f = 1000000000.0 Hz. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, VDD = 1 V, P = 0.1 W.0.50.7511.251.500.20.40.1 WC = 1.0000e-09 F (example)C = 5.0000e-10 FC = 2.0000e-09 FVDD (supply voltage [V]P), dynamic power [W]
P (dynamic power) against VDD (supply voltage) from 0.5 V to 1.5 V. One curve for each value of C (switched capacitance): 1.0000e-09 F, 5.0000e-10 F, 2.0000e-09 F. Other inputs as in the worked example: alpha = 0.1, f = 1000000000.0 Hz. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, VDD = 1 V, P = 0.1 W.
electronics_engineering_ai999x.solve('elx_cmos_dynamic_power', alpha=0.1, C=1e-09, VDD=1.0, f=1000000000.0)
# -> P = 0.1 W, E_supply = 1e-09 J, E_stored = 5e-10 J, I_avg = 0.1 A   (SOLVED)
electronics_engineering_ai999x.solve('elx_cmos_dynamic_power', alpha=0.25, C=5e-11, VDD=3.3, f=100000000.0)
# -> P = 0.0136125 W, E_supply = 5.445e-10 J, E_stored = 2.7225e-10 J, I_avg = 0.004125 A   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
CMOS dynamic power: alpha = 0.1, C = 1000 pF, VDD = 1 V, f = 1000000000 HzSOLVEDP = 0.1 W, E_supply = 1e-09 J, E_stored = 5e-10 J, I_avg = 0.1 A
CMOS dynamic power: alpha = 0.25, C = 50 pF, VDD = 3.3 V, f = 100000000 HzSOLVEDP = 0.0136125 W, E_supply = 5.445e-10 J, E_stored = 2.7225e-10 J, I_avg = 0.004125 A
CMOS dynamic power: C = 1000 pF, VDD = 1 V, f = 1000000000 HzNEEDS_INPUTelx_cmos_dynamic_power needs alpha (activity factor: probability of a 0 -> 1 transition per clock cycle). Example: solve
CMOS dynamic power: alpha = 0.1, C = 1000 pF, VDD = 1 V, f = 1000000000 Hz, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Flip-flop setup and hold slack, maximum clock frequency, elx_setup_hold_timing

The setup slack, hold slack, maximum clock frequency and a verdict for a register-to-register path from clock-to-Q, logic delays, setup and hold times and clock skew (positive when the capture clock is late).

\[T \ge t_{cq} + t_{pd} + t_{su} - t_{skew},\quad t_{ccq} + t_{cd} \ge t_h + t_{skew}\]
inputmeaningcondition
Tclock period
tcqmaximum clock-to-Q delay
tpdmaximum logic delay
tsusetup time
tskewclock skew, capture minus launch
tccqminimum (contamination) clock-to-Q
tcdminimum (contamination) logic delay
thhold time
outputmeaning
setup_slacksetup slack
hold_slackhold slack
f_maxmaximum clock frequency
verdictmeets timing, setup violation, hold violation or both
Flip-flop setup and hold slack, maximum clock frequency: where the verdict changes (verdict)meets timing, setup violation, hold violation or both (verdict) over T (clock period) from 5.0000e-10 s to 5.0000e-08 s and tcq (maximum clock-to-Q delay) from 3.0000e-11 s to 3.0000e-09 s (logarithmic axes): each of the 31 × 21 cells is one run of electronics-engineering-ai999x, coloured by the verdict it returned, meets timing: 349 cells, setup violation: 302 cells. Other inputs as in the worked example: tpd = 3.5000000000000003e-09 s, tsu = 2.0000000000000003e-10 s, tskew = 1.0000000000000002e-10 s, tccq = 1.0000000000000002e-10 s, tcd = 2.0000000000000003e-10 s, th = 1.0000000000000002e-10 s. Marked: the worked example, T = 5.0000e-09 s, tcq = 3.0000e-10 s → meets timing.1.00e-91.00e-81.00e-101.00e-9meets timingverdict: meets timing (349)verdict: setup violation (302)T (clock period [s]tcq), maximum clock-to-Q delay [s]
meets timing, setup violation, hold violation or both (verdict) over T (clock period) from 5.0000e-10 s to 5.0000e-08 s and tcq (maximum clock-to-Q delay) from 3.0000e-11 s to 3.0000e-09 s (logarithmic axes): each of the 31 × 21 cells is one run of electronics-engineering-ai999x, coloured by the verdict it returned, meets timing: 349 cells, setup violation: 302 cells. Other inputs as in the worked example: tpd = 3.5000000000000003e-09 s, tsu = 2.0000000000000003e-10 s, tskew = 1.0000000000000002e-10 s, tccq = 1.0000000000000002e-10 s, tcd = 2.0000000000000003e-10 s, th = 1.0000000000000002e-10 s. Marked: the worked example, T = 5.0000e-09 s, tcq = 3.0000e-10 s → meets timing.
Flip-flop setup and hold slack, maximum clock frequency: setup slack against clock periodsetup_slack (setup slack) against T (clock period) from 2.5000e-09 s to 7.5000e-09 s. One curve for each value of tpd (maximum logic delay): 3.5000e-09 s, 1.7500e-09 s, 7.0000e-09 s. Other inputs as in the worked example: tcq = 3e-10 s, tsu = 2.0000000000000003e-10 s, tskew = 1.0000000000000002e-10 s, tccq = 1.0000000000000002e-10 s, tcd = 2.0000000000000003e-10 s, th = 1.0000000000000002e-10 s. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, T = 5.0000e-09 s, setup_slack = 1.1000e-09 s.4.00e-96.00e-9-5.00e-9-2.50e-902.50e-95.00e-91.1000e-09 stpd = 3.5000e-09 s (example)tpd = 1.7500e-09 stpd = 7.0000e-09 sT (clock period [s]setup_slack), setup slack [s]
setup_slack (setup slack) against T (clock period) from 2.5000e-09 s to 7.5000e-09 s. One curve for each value of tpd (maximum logic delay): 3.5000e-09 s, 1.7500e-09 s, 7.0000e-09 s. Other inputs as in the worked example: tcq = 3e-10 s, tsu = 2.0000000000000003e-10 s, tskew = 1.0000000000000002e-10 s, tccq = 1.0000000000000002e-10 s, tcd = 2.0000000000000003e-10 s, th = 1.0000000000000002e-10 s. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, T = 5.0000e-09 s, setup_slack = 1.1000e-09 s.
electronics_engineering_ai999x.solve('elx_setup_hold_timing', T=5e-09, tcq=3e-10, tpd=3.5e-09, tsu=2e-10, tskew=1e-10, tccq=1e-10, tcd=2e-10, th=1e-10)
# -> setup_slack = 1.1e-09 s, hold_slack = 1e-10 s, f_max = 2.5641e+08 Hz, verdict = meets timing   (SOLVED)
electronics_engineering_ai999x.solve('elx_setup_hold_timing', T=2e-09, tcq=2e-10, tpd=1.9e-09, tsu=1e-10, tskew=-5e-11, tccq=5e-11, tcd=2e-11, th=1e-10)
# -> setup_slack = -2.5e-10 s, hold_slack = 2e-11 s, f_max = 4.44444e+08 Hz, verdict = setup violation   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Setup and hold timing: T = 5 ns, tcq = 0.3 ns, tpd = 3.5 ns, tsu = 0.2 ns, tskew = 0.1 ns, tccq = 0.1 ns, tcd = 0.2 ns, th = 0.1 nsSOLVEDsetup_slack = 1.1e-09 s, hold_slack = 1e-10 s, f_max = 2.5641e+08 Hz, verdict = meets timing
Setup and hold timing: T = 2 ns, tcq = 0.2 ns, tpd = 1.9 ns, tsu = 0.1 ns, tskew = -0.05 ns, tccq = 0.05 ns, tcd = 0.02 ns, th = 0.1 nsSOLVEDsetup_slack = -2.5e-10 s, hold_slack = 2e-11 s, f_max = 4.44444e+08 Hz, verdict = setup violation
Setup and hold timing: tcq = 0.3 ns, tpd = 3.5 ns, tsu = 0.2 ns, tskew = 0.1 ns, tccq = 0.1 ns, tcd = 0.2 ns, th = 0.1 nsNEEDS_INPUTelx_setup_hold_timing needs T (clock period). Example: solve('elx_setup_hold_timing', T='5e-09 s', tcq='3e-10 s', tpd='3
Setup and hold timing: T = 5 ns, tcq = 0.3 ns, tpd = 3.5 ns, tsu = 0.2 ns, tskew = 0.1 ns, tccq = 0.1 ns, tcd = 0.2 ns, th = 0.1 ns, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Synchronizer metastability MTBF, elx_metastability_mtbf

The mean time between synchronizer failures MTBF = exp($tr/\tau)/(T_{0}$ fclk fdata) from the resolution time allowed, the flip-flop's time constant and window, and the clock and data rates.

\[\text{MTBF} = \frac{e^{t_r/\tau}}{T_0f_{clk}f_{data}}\]
inputmeaningcondition
trresolution time available
taumetastability time constant
T0metastability window T0
fclkclock frequency
fdatarate of asynchronous data changes
outputmeaning
MTBF_sMTBF
MTBF_yearsMTBF in years (365.25 days)
log10_MTBF_slog10 of MTBF in seconds
Synchronizer metastability MTBF: log10 of MTBF in seconds against metastability time constantlog10_MTBF_s (log10 of MTBF in seconds) against tau (metastability time constant) from 5.0000e-12 s to 5.0000e-10 s on a logarithmic axis. One curve for each value of tr (resolution time available): 2.0000e-09 s, 1.0000e-09 s, 4.0000e-09 s. Other inputs as in the worked example: T0 = 1e-10 s, fclk = 500000000.0 Hz, fdata = 10000000.0 Hz. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, tau = 5.0000e-11 s, log10_MTBF_s = 11.6728.1.00e-111.00e-10010020011.6728tr = 2.0000e-09 s (example)tr = 1.0000e-09 str = 4.0000e-09 stau (metastability time constant [s]log10_MTBF_s), log10 of MTBF in seconds
log10_MTBF_s (log10 of MTBF in seconds) against tau (metastability time constant) from 5.0000e-12 s to 5.0000e-10 s on a logarithmic axis. One curve for each value of tr (resolution time available): 2.0000e-09 s, 1.0000e-09 s, 4.0000e-09 s. Other inputs as in the worked example: T0 = 1e-10 s, fclk = 500000000.0 Hz, fdata = 10000000.0 Hz. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, tau = 5.0000e-11 s, log10_MTBF_s = 11.6728.
electronics_engineering_ai999x.solve('elx_metastability_mtbf', tr=2e-09, tau=5e-11, T0=1e-10, fclk=500000000.0, fdata=10000000.0)
# -> MTBF_s = 4.70771e+11 s, MTBF_years = 14917.8, log10_MTBF_s = 11.6728   (SOLVED)
electronics_engineering_ai999x.solve('elx_metastability_mtbf', tr=1e-09, tau=2e-11, T0=5e-11, fclk=1000000000.0, fdata=50000000.0)
# -> MTBF_s = 2.07388e+15 s, MTBF_years = 6.57174e+07, log10_MTBF_s = 15.3168   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Metastability MTBF: tr = 2 ns, tau = 50 ps, T0 = 100 ps, fclk = 500000000 Hz, fdata = 10000000 HzSOLVEDMTBF_s = 4.70771e+11 s, MTBF_years = 14917.8, log10_MTBF_s = 11.6728
Metastability MTBF: tr = 1 ns, tau = 20 ps, T0 = 50 ps, fclk = 1000000000 Hz, fdata = 50000000 HzSOLVEDMTBF_s = 2.07388e+15 s, MTBF_years = 6.57174e+07, log10_MTBF_s = 15.3168
Metastability MTBF: tau = 50 ps, T0 = 100 ps, fclk = 500000000 Hz, fdata = 10000000 HzNEEDS_INPUTelx_metastability_mtbf needs tr (resolution time available). Example: solve('elx_metastability_mtbf', tr='2e-09 s', tau=
Metastability MTBF: tr = 2 ns, tau = 50 ps, T0 = 100 ps, fclk = 500000000 Hz, fdata = 10000000 Hz, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Linear regulator dissipation and efficiency, elx_linear_regulator_efficiency

The input and output power, the dissipation in the pass element and the efficiency of a linear (series) regulator including its quiescent current.

\[P_D = (V_{in} - V_{out})I_L + V_{in}I_q,\quad \eta = \frac{V_{out}I_L}{V_{in}(I_L + I_q)}\]
inputmeaningcondition
Vininput voltage
Voutregulated output voltage
Iloadload current
Iqquiescent (ground-pin) current
outputmeaning
P_ininput power
P_outoutput power
P_dissdissipation in the regulator
efficiencyefficiency
efficiency_pctefficiency in per cent
Linear regulator dissipation and efficiency: dissipation in the regulator against input voltageP_diss (dissipation in the regulator) against Vin (input voltage) from 6 V to 18 V. One curve for each value of Iload (load current): 0.5 A, 0.25 A, 1 A. Other inputs as in the worked example: Vout = 5.0 V, Iq = 0.005 A. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Vin = 12 V, P_diss = 3.56 W.101505103.56 WIload = 0.5 A (example)Iload = 0.25 AIload = 1 AVin (input voltage [V]P_diss), dissipation in the regulator [W]
P_diss (dissipation in the regulator) against Vin (input voltage) from 6 V to 18 V. One curve for each value of Iload (load current): 0.5 A, 0.25 A, 1 A. Other inputs as in the worked example: Vout = 5.0 V, Iq = 0.005 A. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Vin = 12 V, P_diss = 3.56 W.
electronics_engineering_ai999x.solve('elx_linear_regulator_efficiency', Vin=12.0, Vout=5.0, Iload=0.5, Iq=0.005)
# -> P_in = 6.06 W, P_out = 2.5 W, P_diss = 3.56 W, efficiency = 0.412541, efficiency_pct = 41.2541   (SOLVED)
electronics_engineering_ai999x.solve('elx_linear_regulator_efficiency', Vin=5.0, Vout=3.3, Iload=0.2, Iq=5e-05)
# -> P_in = 1.00025 W, P_out = 0.66 W, P_diss = 0.34025 W, efficiency = 0.659835, efficiency_pct = 65.9835   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Linear regulator efficiency: Vin = 12 V, Vout = 5 V, Iload = 500 mA, Iq = 5 mASOLVEDP_in = 6.06 W, P_out = 2.5 W, P_diss = 3.56 W, efficiency = 0.412541, efficiency_pct = 41.2541
Linear regulator efficiency: Vin = 5 V, Vout = 3.3 V, Iload = 200 mA, Iq = 0.05 mASOLVEDP_in = 1.00025 W, P_out = 0.66 W, P_diss = 0.34025 W, efficiency = 0.659835, efficiency_pct = 65.9835
Linear regulator efficiency: Vout = 5 V, Iload = 500 mA, Iq = 5 mANEEDS_INPUTelx_linear_regulator_efficiency needs Vin (input voltage). Example: solve('elx_linear_regulator_efficiency', Vin='12 V',
Linear regulator efficiency: Vin = 12 V, Vout = 5 V, Iload = 500 mA, Iq = 5 mA, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Adjustable three-terminal regulator output voltage, elx_adjustable_regulator_output

The output voltage of an adjustable three-terminal regulator (LM317 type: reference between OUT and ADJ, R1 from OUT to ADJ, R2 from ADJ to ground), including the adjust-pin current.

\[V_{out} = V_{ref}\left(1 + \frac{R_2}{R_1}\right) + I_{adj}R_2\]
inputmeaningcondition
R1resistor from OUT to ADJ
R2resistor from ADJ to ground
Vrefinternal reference (1.25 V for the LM317 type)
Iadjadjust-pin current (default 0)
outputmeaning
Voutoutput voltage
I_R1current through R1
Adjustable three-terminal regulator output voltage: output voltage against resistor from OUT to ADJVout (output voltage) against R1 (resistor from OUT to ADJ) from 24 ohm to 2400 ohm on a logarithmic axis. One curve for each value of Vref (internal reference (1.25 V for the LM317 type)): 1.25 V, 0.625 V, 2.5 V. Other inputs as in the worked example: R2 = 720.0 ohm. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R1 = 240 ohm, Vout = 5 V.10010000204060805 VVref = 1.25 V (example)Vref = 0.625 VVref = 2.5 VR1 (resistor from OUT to ADJ [ohm]Vout), output voltage [V]
Vout (output voltage) against R1 (resistor from OUT to ADJ) from 24 ohm to 2400 ohm on a logarithmic axis. One curve for each value of Vref (internal reference (1.25 V for the LM317 type)): 1.25 V, 0.625 V, 2.5 V. Other inputs as in the worked example: R2 = 720.0 ohm. 41 points per curve computed by electronics-engineering-ai999x; marked: the worked example, R1 = 240 ohm, Vout = 5 V.
electronics_engineering_ai999x.solve('elx_adjustable_regulator_output', R1=240.0, R2=720.0, Vref=1.25)
# -> Vout = 5 V, I_R1 = 0.00520833 A   (SOLVED)
electronics_engineering_ai999x.solve('elx_adjustable_regulator_output', R1=240.0, R2=2000.0, Vref=1.25, Iadj=5e-05)
# -> Vout = 11.7667 V, I_R1 = 0.00520833 A   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Adjustable regulator output: R1 = 240 ohm, R2 = 720 ohm, Vref = 1.25 VSOLVEDVout = 5 V, I_R1 = 0.00520833 A
Adjustable regulator output: R1 = 240 ohm, R2 = 2000 ohm, Vref = 1.25 V, Iadj = 50 uASOLVEDVout = 11.7667 V, I_R1 = 0.00520833 A
Adjustable regulator output: R2 = 720 ohm, Vref = 1.25 VNEEDS_INPUTelx_adjustable_regulator_output needs R1 (resistor from OUT to ADJ). Example: solve('elx_adjustable_regulator_output', R
Adjustable regulator output: R1 = 240 ohm, R2 = 720 ohm, Vref = 1.25 V, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Zener-referenced series-pass (emitter-follower) regulator, elx_series_pass_regulator

The output voltage, load, base, Zener and resistor currents and the pass-transistor dissipation of a regulator in which a Zener diode biased through Rs sets the base of an emitter-follower pass transistor.

\[V_{out} = V_Z - V_{BE},\quad I_Z = \frac{V_{in} - V_Z}{R_S} - \frac{I_L}{\beta+1}\]
inputmeaningcondition
Vinunregulated input
VzZener voltage
RsZener bias resistor
RLload resistance
betacurrent gain of the pass transistor
VBEbase-emitter voltage
outputmeaning
Voutoutput voltage Vz - VBE
I_Lload current
I_Bbase current
I_zZener current
I_Rscurrent in Rs
P_Qpass-transistor dissipation
Zener-referenced series-pass (emitter-follower) regulator: output voltage Vz - VBE against Zener voltageVout (output voltage Vz - VBE) against Vz (Zener voltage) from 5 V to 15 V. One curve for each value of VBE (base-emitter voltage): 0.7 V, 0.35 V, 1.4 V. Other inputs as in the worked example: Vin = 15.0 V, Rs = 1000.0 ohm, RL = 100.0 ohm, beta = 100.0. 27 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Vz = 10 V, Vout = 9.3 V.6810121457.51012.59.3 VVBE = 0.7 V (example)VBE = 0.35 VVBE = 1.4 VVz (Zener voltage [V]Vout), output voltage Vz - VBE [V]
Vout (output voltage Vz - VBE) against Vz (Zener voltage) from 5 V to 15 V. One curve for each value of VBE (base-emitter voltage): 0.7 V, 0.35 V, 1.4 V. Other inputs as in the worked example: Vin = 15.0 V, Rs = 1000.0 ohm, RL = 100.0 ohm, beta = 100.0. 27 points per curve computed by electronics-engineering-ai999x; marked: the worked example, Vz = 10 V, Vout = 9.3 V.
electronics_engineering_ai999x.solve('elx_series_pass_regulator', Vin=15.0, Vz=10.0, Rs=1000.0, RL=100.0, beta=100.0, VBE=0.7)
# -> Vout = 9.3 V, I_L = 0.093 A, I_B = 0.000920792 A, I_z = 0.00407921 A, I_Rs = 0.005 A, P_Q = 0.524851 W   (SOLVED)
electronics_engineering_ai999x.solve('elx_series_pass_regulator', Vin=20.0, Vz=12.7, Rs=470.0, RL=50.0, beta=60.0, VBE=0.7)
# -> Vout = 12 V, I_L = 0.24 A, I_B = 0.00393443 A, I_z = 0.0115975 A, I_Rs = 0.0155319 A, P_Q = 1.88852 W   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Series-pass regulator: Vin = 15 V, Vz = 10 V, Rs = 1000 ohm, RL = 100 ohm, beta = 100, VBE = 0.7 VSOLVEDVout = 9.3 V, I_L = 0.093 A, I_B = 0.000920792 A, I_z = 0.00407921 A, I_Rs = 0.005 A, P_Q = 0.524851 W
Series-pass regulator: Vin = 20 V, Vz = 12.7 V, Rs = 470 ohm, RL = 50 ohm, beta = 60, VBE = 0.7 VSOLVEDVout = 12 V, I_L = 0.24 A, I_B = 0.00393443 A, I_z = 0.0115975 A, I_Rs = 0.0155319 A, P_Q = 1.88852 W
Series-pass regulator: Vz = 10 V, Rs = 1000 ohm, RL = 100 ohm, beta = 100, VBE = 0.7 VNEEDS_INPUTelx_series_pass_regulator needs Vin (unregulated input). Example: solve('elx_series_pass_regulator', Vin='15 V', Vz='10
Series-pass regulator: Vin = 15 V, Vz = 10 V, Rs = 1000 ohm, RL = 100 ohm, beta = 100, VBE = 0.7 V, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te

Heat-sink thermal path: junction, case and sink temperatures, elx_heat_sink_temperatures

The junction, case and heat-sink temperatures of a power device dissipating P through junction-to-case, case-to-sink (interface) and sink-to-ambient thermal resistances.

\[T_j = T_a + P\,(\theta_{jc} + \theta_{cs} + \theta_{sa})\]
inputmeaningcondition
Ppower dissipated
Taambient temperature
theta_jcjunction-to-case thermal resistance
theta_cscase-to-sink thermal resistance
theta_sasink-to-ambient thermal resistance
outputmeaning
Tjjunction temperature
Tccase temperature
Tssink temperature
Tj_Cjunction temperature in degC
theta_jatotal junction-to-ambient resistance
Heat-sink thermal path: junction, case and sink temperatures: junction temperature against power dissipatedTj (junction temperature) against P (power dissipated) from 7.5 W to 22.5 W. One curve for each value of Ta (ambient temperature): 298.15 K, 149.075 K, 596.3 K. Other inputs as in the worked example: theta_jc = 1.5 K/W, theta_cs = 0.5 K/W, theta_sa = 3.0 K/W. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, P = 15 W, Tj = 373.15 K.101520200400600373.15 KTa = 298.15 K (example)Ta = 149.075 KTa = 596.3 KP (power dissipated [W]Tj), junction temperature [K]
Tj (junction temperature) against P (power dissipated) from 7.5 W to 22.5 W. One curve for each value of Ta (ambient temperature): 298.15 K, 149.075 K, 596.3 K. Other inputs as in the worked example: theta_jc = 1.5 K/W, theta_cs = 0.5 K/W, theta_sa = 3.0 K/W. 31 points per curve computed by electronics-engineering-ai999x; marked: the worked example, P = 15 W, Tj = 373.15 K.
electronics_engineering_ai999x.solve('elx_heat_sink_temperatures', P=15.0, Ta=298.15, theta_jc=1.5, theta_cs=0.5, theta_sa=3.0)
# -> Tj = 373.15 K, Tc = 350.65 K, Ts = 343.15 K, Tj_C = 100, theta_ja = 5 K/W   (SOLVED)
electronics_engineering_ai999x.solve('elx_heat_sink_temperatures', P=40.0, Ta=313.15, theta_jc=0.8, theta_cs=0.2, theta_sa=1.2)
# -> Tj = 401.15 K, Tc = 369.15 K, Ts = 361.15 K, Tj_C = 128, theta_ja = 2.2 K/W   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Heat sink temperatures: P = 15 W, Ta = 25 degC, theta_jc = 1.5 K/W, theta_cs = 0.5 K/W, theta_sa = 3 K/WSOLVEDTj = 373.15 K, Tc = 350.65 K, Ts = 343.15 K, Tj_C = 100, theta_ja = 5 K/W
Heat sink temperatures: P = 40 W, Ta = 40 degC, theta_jc = 0.8 K/W, theta_cs = 0.2 K/W, theta_sa = 1.2 K/WSOLVEDTj = 401.15 K, Tc = 369.15 K, Ts = 361.15 K, Tj_C = 128, theta_ja = 2.2 K/W
Heat sink temperatures: Ta = 25 degC, theta_jc = 1.5 K/W, theta_cs = 0.5 K/W, theta_sa = 3 K/WNEEDS_INPUTelx_heat_sink_temperatures needs P (power dissipated). Example: solve('elx_heat_sink_temperatures', P='15 W', Ta='298.15
Heat sink temperatures: P = 15 W, Ta = 25 degC, theta_jc = 1.5 K/W, theta_cs = 0.5 K/W, theta_sa = 3 K/W, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te
Heat sink temperatures: P = 15 W, Ta = 25 degC, theta_jc = 1.5 degC/W, theta_cs = 0.5 degC/W, theta_sa = 3 degC/WSOLVEDTj = 373.15 K, Tc = 350.65 K, Ts = 343.15 K, Tj_C = 100, theta_ja = 5 K/W

Required heat-sink thermal resistance, elx_heat_sink_required

The largest sink-to-ambient thermal resistance (and total junction-to-ambient resistance) that keeps a device dissipating P below its maximum junction temperature.

\[\theta_{sa} \le \frac{T_{j,max} - T_a}{P} - \theta_{jc} - \theta_{cs}\]
inputmeaningcondition
Ppower dissipated
Taambient temperature
Tj_maxmaximum junction temperature
theta_jcjunction-to-case thermal resistance
theta_cscase-to-sink thermal resistance
outputmeaning
theta_ja_maxlargest junction-to-ambient resistance
theta_sa_maxlargest sink-to-ambient resistance
Required heat-sink thermal resistance: largest sink-to-ambient resistance against power dissipatedtheta_sa_max (largest sink-to-ambient resistance) against P (power dissipated) from 2 W to 200 W on a logarithmic axis. One curve for each value of Tj_max (maximum junction temperature): 423.15 K, 846.3 K. Other inputs as in the worked example: Ta = 313.15 K, theta_jc = 1.0 K/W, theta_cs = 0.5 K/W. 32 points per curve computed by electronics-engineering-ai999x; marked: the worked example, P = 20 W, theta_sa_max = 4 K/W.1010001002004 K/WTj_max = 423.15 K (example)Tj_max = 846.3 KP, power dissipated [W]theta_sa_max [K/W]
theta_sa_max (largest sink-to-ambient resistance) against P (power dissipated) from 2 W to 200 W on a logarithmic axis. One curve for each value of Tj_max (maximum junction temperature): 423.15 K, 846.3 K. Other inputs as in the worked example: Ta = 313.15 K, theta_jc = 1.0 K/W, theta_cs = 0.5 K/W. 32 points per curve computed by electronics-engineering-ai999x; marked: the worked example, P = 20 W, theta_sa_max = 4 K/W.
electronics_engineering_ai999x.solve('elx_heat_sink_required', P=20.0, Ta=313.15, Tj_max=423.15, theta_jc=1.0, theta_cs=0.5)
# -> theta_ja_max = 5.5 K/W, theta_sa_max = 4 K/W   (SOLVED)
electronics_engineering_ai999x.solve('elx_heat_sink_required', P=8.0, Ta=323.15, Tj_max=398.15, theta_jc=2.5, theta_cs=0.3)
# -> theta_ja_max = 9.375 K/W, theta_sa_max = 6.575 K/W   (SOLVED)

Questions in words (documented forms), as executed:

questionoutcomeresult
Required heat sink: P = 20 W, Ta = 40 degC, Tj_max = 150 degC, theta_jc = 1 K/W, theta_cs = 0.5 K/WSOLVEDtheta_ja_max = 5.5 K/W, theta_sa_max = 4 K/W
Required heat sink: P = 8 W, Ta = 50 degC, Tj_max = 125 degC, theta_jc = 2.5 K/W, theta_cs = 0.3 K/WSOLVEDtheta_ja_max = 9.375 K/W, theta_sa_max = 6.575 K/W
Required heat sink: Ta = 40 degC, Tj_max = 150 degC, theta_jc = 1 K/W, theta_cs = 0.5 K/WNEEDS_INPUTelx_heat_sink_required needs P (power dissipated). Example: solve('elx_heat_sink_required', P='20 W', Ta='313.15 K', Tj_
Required heat sink: P = 20 W, Ta = 40 degC, Tj_max = 150 degC, theta_jc = 1 K/W, theta_cs = 0.5 K/W, zz = 1UNRECOGNIZED_FORMATI could not match this question to a documented form, so I will not guess. Every form: electronics_engineering_ai999x.te