File size: 100,236 Bytes
a9536d3 | 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 598 599 600 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 620 621 622 623 624 625 626 627 628 629 630 631 632 633 634 635 636 637 638 639 640 641 642 643 644 645 646 647 648 649 650 651 652 653 654 655 656 657 658 659 660 661 662 663 664 665 666 667 668 669 670 671 672 673 674 675 676 677 678 679 680 681 682 683 684 685 686 687 688 689 690 691 692 693 694 695 696 697 698 699 700 701 702 703 704 705 706 707 708 709 710 711 712 713 714 715 716 717 718 719 720 721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736 737 738 739 740 741 742 743 744 745 746 747 748 749 750 751 752 753 754 755 756 757 758 759 760 761 762 763 764 765 766 767 768 769 770 771 772 773 774 775 776 777 778 779 780 781 782 783 784 785 786 787 788 789 790 791 792 793 794 795 796 797 798 799 800 801 802 803 804 805 806 807 808 809 810 811 812 813 814 815 816 817 818 819 820 821 822 823 824 825 826 827 828 829 830 831 832 833 834 835 836 837 838 839 840 841 842 843 844 845 846 847 848 849 850 851 852 853 854 855 856 857 858 859 860 861 862 863 864 865 866 867 868 869 870 871 872 873 874 875 876 877 878 879 880 881 882 883 884 885 886 887 888 889 890 891 892 893 894 895 896 897 898 899 900 901 902 903 904 905 906 907 908 909 910 911 912 913 914 915 916 917 918 919 920 921 922 923 924 925 926 927 928 929 930 931 932 933 934 935 936 937 938 939 940 941 942 943 944 945 946 947 948 949 950 951 952 953 954 955 956 957 958 959 960 961 962 963 964 965 966 967 968 969 970 971 972 973 974 975 976 977 978 979 980 981 982 983 984 985 986 987 988 989 990 991 992 993 994 995 996 997 998 999 1000 1001 1002 1003 1004 1005 1006 1007 1008 1009 1010 1011 1012 1013 1014 1015 1016 1017 1018 1019 1020 1021 1022 1023 1024 1025 1026 1027 1028 1029 1030 1031 1032 1033 1034 1035 1036 1037 1038 1039 1040 1041 1042 1043 1044 1045 1046 1047 1048 1049 1050 1051 1052 1053 1054 1055 1056 1057 1058 1059 1060 1061 1062 1063 1064 1065 1066 1067 1068 1069 1070 1071 1072 1073 1074 1075 1076 1077 1078 1079 1080 1081 1082 1083 1084 1085 1086 1087 1088 1089 1090 1091 1092 1093 1094 1095 1096 1097 1098 1099 1100 1101 1102 1103 1104 1105 1106 1107 1108 1109 1110 1111 1112 1113 1114 1115 1116 1117 1118 1119 1120 1121 1122 1123 1124 1125 1126 1127 1128 1129 1130 1131 1132 1133 1134 1135 1136 1137 1138 1139 1140 1141 1142 1143 1144 1145 1146 1147 1148 1149 1150 1151 1152 1153 1154 1155 1156 1157 1158 1159 1160 1161 1162 1163 1164 1165 1166 1167 1168 1169 1170 1171 1172 1173 1174 1175 1176 1177 1178 1179 1180 1181 1182 1183 1184 1185 1186 1187 1188 1189 1190 1191 1192 1193 1194 1195 1196 1197 1198 1199 1200 1201 1202 1203 1204 1205 1206 1207 1208 1209 1210 1211 1212 1213 1214 1215 1216 1217 1218 1219 1220 1221 1222 1223 1224 1225 1226 1227 1228 1229 1230 1231 1232 1233 1234 1235 1236 1237 1238 1239 1240 1241 1242 1243 1244 1245 1246 1247 1248 1249 1250 1251 1252 1253 1254 1255 1256 1257 1258 1259 1260 1261 1262 1263 1264 1265 1266 1267 1268 1269 1270 1271 1272 1273 1274 1275 1276 1277 1278 1279 1280 1281 1282 1283 1284 1285 1286 1287 1288 1289 1290 1291 1292 1293 1294 1295 1296 1297 1298 1299 1300 1301 1302 1303 1304 1305 1306 1307 1308 1309 1310 1311 1312 1313 1314 1315 1316 1317 1318 1319 1320 1321 1322 1323 1324 1325 1326 1327 1328 1329 1330 1331 1332 1333 1334 1335 1336 1337 1338 1339 1340 1341 1342 1343 1344 1345 1346 1347 1348 1349 1350 1351 1352 1353 1354 1355 1356 1357 1358 1359 1360 1361 1362 1363 1364 1365 1366 1367 1368 1369 1370 1371 1372 1373 1374 1375 1376 1377 1378 1379 1380 1381 1382 1383 1384 1385 1386 1387 1388 1389 1390 1391 1392 1393 1394 1395 1396 1397 1398 1399 1400 1401 1402 1403 1404 1405 1406 1407 1408 1409 1410 1411 1412 1413 1414 1415 1416 1417 1418 1419 1420 1421 1422 1423 1424 1425 1426 1427 1428 1429 1430 1431 1432 1433 1434 1435 1436 1437 1438 1439 1440 1441 1442 1443 1444 1445 1446 1447 1448 1449 1450 1451 1452 1453 1454 1455 1456 1457 1458 1459 1460 1461 1462 1463 1464 1465 1466 1467 1468 1469 1470 1471 1472 1473 1474 1475 1476 1477 1478 1479 1480 1481 1482 1483 1484 1485 1486 1487 1488 1489 1490 1491 1492 1493 1494 1495 1496 1497 1498 1499 1500 1501 1502 1503 1504 1505 1506 1507 1508 1509 1510 1511 1512 1513 1514 1515 1516 1517 1518 1519 1520 1521 1522 1523 1524 1525 1526 1527 1528 1529 1530 1531 1532 1533 1534 1535 1536 1537 1538 1539 1540 1541 1542 1543 1544 1545 1546 1547 1548 1549 1550 1551 1552 1553 1554 1555 1556 1557 1558 1559 1560 1561 1562 1563 1564 1565 1566 1567 1568 1569 1570 1571 1572 1573 1574 1575 1576 1577 1578 1579 1580 1581 1582 1583 1584 1585 1586 1587 1588 1589 1590 1591 1592 1593 1594 1595 1596 1597 1598 1599 1600 1601 1602 1603 1604 1605 1606 1607 1608 1609 1610 1611 1612 1613 1614 1615 1616 1617 1618 1619 1620 1621 1622 1623 1624 1625 1626 1627 1628 1629 1630 1631 1632 1633 1634 1635 1636 1637 1638 1639 1640 1641 1642 1643 1644 1645 1646 1647 1648 1649 1650 1651 1652 1653 1654 1655 1656 1657 1658 1659 1660 1661 1662 1663 1664 1665 1666 1667 1668 1669 1670 1671 1672 1673 1674 1675 1676 1677 1678 1679 1680 1681 1682 1683 1684 1685 1686 1687 1688 1689 1690 1691 1692 1693 1694 1695 1696 1697 1698 1699 1700 1701 1702 1703 1704 1705 1706 1707 1708 1709 1710 1711 1712 1713 1714 1715 1716 1717 1718 1719 1720 1721 1722 1723 1724 1725 1726 1727 1728 1729 1730 1731 1732 1733 1734 1735 1736 1737 1738 1739 1740 1741 1742 1743 1744 1745 1746 1747 1748 1749 1750 1751 1752 1753 1754 1755 1756 1757 1758 1759 1760 1761 1762 1763 1764 1765 1766 1767 1768 1769 1770 1771 1772 1773 1774 1775 1776 1777 1778 1779 1780 1781 1782 1783 1784 1785 1786 1787 1788 1789 1790 1791 1792 1793 1794 1795 1796 1797 1798 1799 1800 1801 1802 1803 1804 1805 1806 1807 1808 1809 1810 1811 1812 1813 1814 1815 1816 1817 1818 1819 1820 1821 1822 1823 1824 1825 1826 1827 1828 1829 1830 1831 1832 1833 1834 1835 1836 1837 1838 1839 1840 1841 1842 1843 1844 1845 1846 1847 1848 1849 1850 1851 1852 1853 1854 1855 1856 1857 1858 1859 1860 1861 1862 1863 1864 1865 1866 1867 1868 1869 1870 1871 1872 1873 1874 1875 1876 1877 1878 1879 1880 1881 1882 1883 1884 1885 1886 1887 1888 1889 1890 1891 1892 1893 1894 1895 1896 1897 1898 1899 1900 1901 1902 1903 1904 1905 1906 1907 1908 1909 1910 1911 1912 1913 1914 1915 1916 1917 1918 1919 1920 1921 1922 1923 1924 1925 1926 1927 1928 1929 1930 1931 1932 1933 1934 1935 1936 1937 1938 1939 1940 1941 1942 1943 1944 1945 1946 1947 1948 1949 1950 1951 1952 1953 1954 1955 1956 1957 1958 1959 1960 1961 1962 1963 1964 1965 1966 1967 1968 1969 1970 1971 1972 1973 1974 1975 1976 1977 1978 1979 1980 1981 1982 1983 1984 1985 1986 1987 1988 1989 1990 1991 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020 2021 2022 2023 2024 2025 2026 2027 2028 2029 2030 2031 2032 2033 2034 2035 2036 2037 2038 2039 2040 2041 2042 2043 2044 2045 2046 2047 2048 2049 2050 2051 2052 2053 2054 2055 2056 2057 2058 2059 2060 2061 2062 2063 2064 2065 2066 2067 2068 2069 2070 2071 2072 2073 2074 2075 2076 2077 2078 2079 2080 2081 2082 2083 2084 2085 2086 2087 2088 2089 2090 2091 2092 2093 2094 2095 2096 2097 2098 2099 2100 2101 2102 2103 2104 2105 2106 2107 2108 2109 2110 2111 2112 2113 2114 2115 2116 2117 2118 2119 2120 2121 2122 2123 2124 2125 2126 2127 2128 2129 2130 2131 2132 2133 2134 2135 2136 2137 2138 2139 2140 2141 2142 2143 2144 2145 2146 2147 2148 2149 2150 2151 2152 2153 2154 2155 2156 2157 2158 2159 2160 2161 2162 2163 2164 2165 2166 2167 2168 2169 2170 2171 2172 2173 2174 2175 2176 2177 2178 2179 2180 2181 2182 2183 2184 2185 2186 2187 2188 2189 2190 2191 2192 2193 2194 2195 2196 2197 2198 2199 2200 2201 2202 2203 2204 2205 2206 2207 2208 2209 2210 2211 2212 2213 2214 2215 2216 2217 2218 2219 2220 2221 2222 2223 2224 2225 2226 2227 2228 2229 2230 2231 2232 2233 2234 2235 2236 2237 2238 2239 2240 2241 2242 2243 2244 2245 2246 2247 2248 2249 2250 2251 2252 2253 2254 2255 2256 2257 2258 2259 2260 2261 2262 2263 2264 2265 2266 2267 2268 2269 2270 2271 2272 2273 2274 2275 2276 2277 2278 2279 2280 2281 2282 2283 2284 2285 2286 2287 2288 2289 2290 2291 2292 2293 2294 2295 2296 2297 2298 2299 2300 2301 2302 2303 2304 2305 2306 2307 2308 2309 2310 2311 2312 2313 2314 2315 2316 2317 2318 2319 2320 2321 2322 2323 2324 2325 2326 2327 2328 2329 2330 2331 2332 2333 2334 2335 2336 2337 2338 2339 2340 2341 2342 2343 2344 2345 2346 2347 2348 2349 2350 2351 2352 2353 2354 2355 2356 2357 2358 2359 2360 2361 2362 2363 2364 2365 2366 2367 2368 2369 2370 2371 2372 2373 2374 2375 2376 2377 2378 2379 2380 2381 2382 2383 2384 2385 2386 2387 2388 2389 2390 2391 2392 2393 2394 2395 2396 2397 2398 2399 2400 2401 2402 2403 2404 2405 2406 2407 2408 2409 2410 2411 2412 2413 2414 2415 2416 2417 2418 2419 2420 2421 2422 2423 2424 2425 2426 2427 2428 2429 2430 2431 2432 2433 2434 2435 2436 2437 2438 2439 2440 2441 2442 2443 2444 2445 2446 2447 2448 2449 2450 2451 2452 2453 2454 2455 2456 2457 2458 2459 2460 2461 2462 2463 2464 2465 2466 2467 2468 2469 2470 2471 2472 2473 2474 2475 2476 2477 2478 2479 2480 2481 2482 2483 2484 2485 2486 2487 2488 2489 2490 2491 2492 2493 2494 2495 2496 2497 2498 2499 2500 2501 2502 2503 2504 2505 2506 2507 2508 2509 2510 2511 2512 2513 2514 2515 2516 2517 2518 2519 2520 2521 2522 2523 2524 2525 2526 2527 2528 2529 2530 2531 2532 2533 2534 2535 2536 2537 2538 2539 2540 2541 2542 2543 2544 2545 2546 2547 2548 2549 2550 2551 2552 2553 2554 2555 2556 2557 2558 2559 2560 2561 2562 2563 2564 2565 2566 2567 2568 2569 2570 2571 2572 2573 | /*!
* Arduino Library for driving Adafruit NeoPixel addressable LEDs,
* FLORA RGB Smart Pixels and compatible devicess -- WS2811, WS2812, WS2812B,
* SK6812, etc.
* This is the documentation for Adafruit's NeoPixel library for the
* Arduino platform, allowing a broad range of microcontroller boards
* (most AVR boards, many ARM devices, ESP8266 and ESP32, among others)
* to control Adafruit NeoPixels, FLORA RGB Smart Pixels and compatible
* devices -- WS2811, WS2812, WS2812B, SK6812, etc.
*
* Adafruit invests time and resources providing this open source code,
* please support Adafruit and open-source hardware by purchasing products
* from Adafruit!
*
* Written by Phil "Paint Your Dragon" Burgess for Adafruit Industries,
* with contributions by PJRC, Michael Miller and other members of the
* open source community.
* This file is part of the Adafruit_NeoPixel library.
*
* Adafruit_NeoPixel is free software: you can redistribute it and/or
* modify it under the terms of the GNU Lesser General Public License as
* published by the Free Software Foundation, either version 3 of the
* License, or (at your option) any later version.
*
* Adafruit_NeoPixel is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU Lesser General Public License for more details.
*
* You should have received a copy of the GNU Lesser General Public
* License along with NeoPixel. If not, see
* <http://www.gnu.org/licenses/>.
*
*/
#include "Adafruit_CPlay_NeoPixel.h"
#ifdef TARGET_LPC1768
#include <time.h>
#endif
#if defined(NRF52) || defined(NRF52_SERIES)
#include "nrf.h"
// Interrupt is only disabled if there is no PWM device available
// Note: Adafruit Bluefruit nrf52 does not use this option
//#define NRF52_DISABLE_INT
#endif
/*!
@brief NeoPixel constructor when length, pin and pixel type are known
at compile-time.
@param n Number of NeoPixels in strand.
@param p Arduino pin number which will drive the NeoPixel data in.
@param t Pixel type -- add together NEO_* constants defined in
Adafruit_CPlay_NeoPixel.h, for example NEO_GRB+NEO_KHZ800 for
NeoPixels expecting an 800 KHz (vs 400 KHz) data stream
with color bytes expressed in green, red, blue order per
pixel.
*/
Adafruit_CPlay_NeoPixel::Adafruit_CPlay_NeoPixel(uint16_t n, uint16_t p, neoPixelType t) :
begun(false), brightness(0), pixels(NULL), endTime(0) {
updateType(t);
updateLength(n);
setPin(p);
}
/*!
@brief "Empty" NeoPixel constructor when length, pin and/or pixel type
are not known at compile-time, and must be initialized later with
updateType(), updateLength() and setPin().
@note This function is deprecated, here only for old projects that
may still be calling it. New projects should instead use the
'new' keyword with the first constructor syntax (length, pin,
type).
*/
Adafruit_CPlay_NeoPixel::Adafruit_CPlay_NeoPixel() :
#ifdef NEO_KHZ400
is800KHz(true),
#endif
begun(false), numLEDs(0), numBytes(0), pin(-1), brightness(0), pixels(NULL),
rOffset(1), gOffset(0), bOffset(2), wOffset(1), endTime(0) {
}
/*!
@brief Deallocate Adafruit_CPlay_NeoPixel object, set data pin back to INPUT.
*/
Adafruit_CPlay_NeoPixel::~Adafruit_CPlay_NeoPixel() {
free(pixels);
if(pin >= 0) pinMode(pin, INPUT);
}
/*!
@brief Configure NeoPixel pin for output.
*/
void Adafruit_CPlay_NeoPixel::begin(void) {
if(pin >= 0) {
pinMode(pin, OUTPUT);
digitalWrite(pin, LOW);
}
begun = true;
}
/*!
@brief Change the length of a previously-declared Adafruit_CPlay_NeoPixel
strip object. Old data is deallocated and new data is cleared.
Pin number and pixel format are unchanged.
@param n New length of strip, in pixels.
@note This function is deprecated, here only for old projects that
may still be calling it. New projects should instead use the
'new' keyword with the first constructor syntax (length, pin,
type).
*/
void Adafruit_CPlay_NeoPixel::updateLength(uint16_t n) {
free(pixels); // Free existing data (if any)
// Allocate new data -- note: ALL PIXELS ARE CLEARED
numBytes = n * ((wOffset == rOffset) ? 3 : 4);
if((pixels = (uint8_t *)malloc(numBytes))) {
memset(pixels, 0, numBytes);
numLEDs = n;
} else {
numLEDs = numBytes = 0;
}
}
/*!
@brief Change the pixel format of a previously-declared
Adafruit_CPlay_NeoPixel strip object. If format changes from one of
the RGB variants to an RGBW variant (or RGBW to RGB), the old
data will be deallocated and new data is cleared. Otherwise,
the old data will remain in RAM and is not reordered to the
new format, so it's advisable to follow up with clear().
@param t Pixel type -- add together NEO_* constants defined in
Adafruit_CPlay_NeoPixel.h, for example NEO_GRB+NEO_KHZ800 for
NeoPixels expecting an 800 KHz (vs 400 KHz) data stream
with color bytes expressed in green, red, blue order per
pixel.
@note This function is deprecated, here only for old projects that
may still be calling it. New projects should instead use the
'new' keyword with the first constructor syntax
(length, pin, type).
*/
void Adafruit_CPlay_NeoPixel::updateType(neoPixelType t) {
boolean oldThreeBytesPerPixel = (wOffset == rOffset); // false if RGBW
wOffset = (t >> 6) & 0b11; // See notes in header file
rOffset = (t >> 4) & 0b11; // regarding R/G/B/W offsets
gOffset = (t >> 2) & 0b11;
bOffset = t & 0b11;
#ifdef NEO_KHZ400
is800KHz = (t < 256); // 400 KHz flag is 1<<8
#endif
// If bytes-per-pixel has changed (and pixel data was previously
// allocated), re-allocate to new size. Will clear any data.
if(pixels) {
boolean newThreeBytesPerPixel = (wOffset == rOffset);
if(newThreeBytesPerPixel != oldThreeBytesPerPixel) updateLength(numLEDs);
}
}
#if defined(ESP8266)
// ESP8266 show() is external to enforce ICACHE_RAM_ATTR execution
extern "C" void ICACHE_RAM_ATTR espShow(
uint16_t pin, uint8_t *pixels, uint32_t numBytes, uint8_t type);
#elif defined(ESP32)
extern "C" void espShow(
uint16_t pin, uint8_t *pixels, uint32_t numBytes, uint8_t type);
#endif // ESP8266
/*!
@brief Transmit pixel data in RAM to NeoPixels.
@note On most architectures, interrupts are temporarily disabled in
order to achieve the correct NeoPixel signal timing. This means
that the Arduino millis() and micros() functions, which require
interrupts, will lose small intervals of time whenever this
function is called (about 30 microseconds per RGB pixel, 40 for
RGBW pixels). There's no easy fix for this, but a few
specialized alternative or companion libraries exist that use
very device-specific peripherals to work around it.
*/
void Adafruit_CPlay_NeoPixel::show(void) {
if(!pixels) return;
// Data latch = 300+ microsecond pause in the output stream. Rather than
// put a delay at the end of the function, the ending time is noted and
// the function will simply hold off (if needed) on issuing the
// subsequent round of data until the latch time has elapsed. This
// allows the mainline code to start generating the next frame of data
// rather than stalling for the latch.
while(!canShow());
// endTime is a private member (rather than global var) so that multiple
// instances on different pins can be quickly issued in succession (each
// instance doesn't delay the next).
// In order to make this code runtime-configurable to work with any pin,
// SBI/CBI instructions are eschewed in favor of full PORT writes via the
// OUT or ST instructions. It relies on two facts: that peripheral
// functions (such as PWM) take precedence on output pins, so our PORT-
// wide writes won't interfere, and that interrupts are globally disabled
// while data is being issued to the LEDs, so no other code will be
// accessing the PORT. The code takes an initial 'snapshot' of the PORT
// state, computes 'pin high' and 'pin low' values, and writes these back
// to the PORT register as needed.
// NRF52 may use PWM + DMA (if available), may not need to disable interrupt
#if !( defined(NRF52) || defined(NRF52_SERIES) )
noInterrupts(); // Need 100% focus on instruction timing
#endif
#ifdef __AVR__
// AVR MCUs -- ATmega & ATtiny (no XMEGA) ---------------------------------
volatile uint16_t
i = numBytes; // Loop counter
volatile uint8_t
*ptr = pixels, // Pointer to next byte
b = *ptr++, // Current byte value
hi, // PORT w/output bit set high
lo; // PORT w/output bit set low
// Hand-tuned assembly code issues data to the LED drivers at a specific
// rate. There's separate code for different CPU speeds (8, 12, 16 MHz)
// for both the WS2811 (400 KHz) and WS2812 (800 KHz) drivers. The
// datastream timing for the LED drivers allows a little wiggle room each
// way (listed in the datasheets), so the conditions for compiling each
// case are set up for a range of frequencies rather than just the exact
// 8, 12 or 16 MHz values, permitting use with some close-but-not-spot-on
// devices (e.g. 16.5 MHz DigiSpark). The ranges were arrived at based
// on the datasheet figures and have not been extensively tested outside
// the canonical 8/12/16 MHz speeds; there's no guarantee these will work
// close to the extremes (or possibly they could be pushed further).
// Keep in mind only one CPU speed case actually gets compiled; the
// resulting program isn't as massive as it might look from source here.
// 8 MHz(ish) AVR ---------------------------------------------------------
#if (F_CPU >= 7400000UL) && (F_CPU <= 9500000UL)
#ifdef NEO_KHZ400 // 800 KHz check needed only if 400 KHz support enabled
if(is800KHz) {
#endif
volatile uint8_t n1, n2 = 0; // First, next bits out
// Squeezing an 800 KHz stream out of an 8 MHz chip requires code
// specific to each PORT register.
// 10 instruction clocks per bit: HHxxxxxLLL
// OUT instructions: ^ ^ ^ (T=0,2,7)
// PORTD OUTPUT ----------------------------------------------------
#if defined(PORTD)
#if defined(PORTB) || defined(PORTC) || defined(PORTF)
if(port == &PORTD) {
#endif // defined(PORTB/C/F)
hi = PORTD | pinMask;
lo = PORTD & ~pinMask;
n1 = lo;
if(b & 0x80) n1 = hi;
// Dirty trick: RJMPs proceeding to the next instruction are used
// to delay two clock cycles in one instruction word (rather than
// using two NOPs). This was necessary in order to squeeze the
// loop down to exactly 64 words -- the maximum possible for a
// relative branch.
asm volatile(
"headD:" "\n\t" // Clk Pseudocode
// Bit 7:
"out %[port] , %[hi]" "\n\t" // 1 PORT = hi
"mov %[n2] , %[lo]" "\n\t" // 1 n2 = lo
"out %[port] , %[n1]" "\n\t" // 1 PORT = n1
"rjmp .+0" "\n\t" // 2 nop nop
"sbrc %[byte] , 6" "\n\t" // 1-2 if(b & 0x40)
"mov %[n2] , %[hi]" "\n\t" // 0-1 n2 = hi
"out %[port] , %[lo]" "\n\t" // 1 PORT = lo
"rjmp .+0" "\n\t" // 2 nop nop
// Bit 6:
"out %[port] , %[hi]" "\n\t" // 1 PORT = hi
"mov %[n1] , %[lo]" "\n\t" // 1 n1 = lo
"out %[port] , %[n2]" "\n\t" // 1 PORT = n2
"rjmp .+0" "\n\t" // 2 nop nop
"sbrc %[byte] , 5" "\n\t" // 1-2 if(b & 0x20)
"mov %[n1] , %[hi]" "\n\t" // 0-1 n1 = hi
"out %[port] , %[lo]" "\n\t" // 1 PORT = lo
"rjmp .+0" "\n\t" // 2 nop nop
// Bit 5:
"out %[port] , %[hi]" "\n\t" // 1 PORT = hi
"mov %[n2] , %[lo]" "\n\t" // 1 n2 = lo
"out %[port] , %[n1]" "\n\t" // 1 PORT = n1
"rjmp .+0" "\n\t" // 2 nop nop
"sbrc %[byte] , 4" "\n\t" // 1-2 if(b & 0x10)
"mov %[n2] , %[hi]" "\n\t" // 0-1 n2 = hi
"out %[port] , %[lo]" "\n\t" // 1 PORT = lo
"rjmp .+0" "\n\t" // 2 nop nop
// Bit 4:
"out %[port] , %[hi]" "\n\t" // 1 PORT = hi
"mov %[n1] , %[lo]" "\n\t" // 1 n1 = lo
"out %[port] , %[n2]" "\n\t" // 1 PORT = n2
"rjmp .+0" "\n\t" // 2 nop nop
"sbrc %[byte] , 3" "\n\t" // 1-2 if(b & 0x08)
"mov %[n1] , %[hi]" "\n\t" // 0-1 n1 = hi
"out %[port] , %[lo]" "\n\t" // 1 PORT = lo
"rjmp .+0" "\n\t" // 2 nop nop
// Bit 3:
"out %[port] , %[hi]" "\n\t" // 1 PORT = hi
"mov %[n2] , %[lo]" "\n\t" // 1 n2 = lo
"out %[port] , %[n1]" "\n\t" // 1 PORT = n1
"rjmp .+0" "\n\t" // 2 nop nop
"sbrc %[byte] , 2" "\n\t" // 1-2 if(b & 0x04)
"mov %[n2] , %[hi]" "\n\t" // 0-1 n2 = hi
"out %[port] , %[lo]" "\n\t" // 1 PORT = lo
"rjmp .+0" "\n\t" // 2 nop nop
// Bit 2:
"out %[port] , %[hi]" "\n\t" // 1 PORT = hi
"mov %[n1] , %[lo]" "\n\t" // 1 n1 = lo
"out %[port] , %[n2]" "\n\t" // 1 PORT = n2
"rjmp .+0" "\n\t" // 2 nop nop
"sbrc %[byte] , 1" "\n\t" // 1-2 if(b & 0x02)
"mov %[n1] , %[hi]" "\n\t" // 0-1 n1 = hi
"out %[port] , %[lo]" "\n\t" // 1 PORT = lo
"rjmp .+0" "\n\t" // 2 nop nop
// Bit 1:
"out %[port] , %[hi]" "\n\t" // 1 PORT = hi
"mov %[n2] , %[lo]" "\n\t" // 1 n2 = lo
"out %[port] , %[n1]" "\n\t" // 1 PORT = n1
"rjmp .+0" "\n\t" // 2 nop nop
"sbrc %[byte] , 0" "\n\t" // 1-2 if(b & 0x01)
"mov %[n2] , %[hi]" "\n\t" // 0-1 n2 = hi
"out %[port] , %[lo]" "\n\t" // 1 PORT = lo
"sbiw %[count], 1" "\n\t" // 2 i-- (don't act on Z flag yet)
// Bit 0:
"out %[port] , %[hi]" "\n\t" // 1 PORT = hi
"mov %[n1] , %[lo]" "\n\t" // 1 n1 = lo
"out %[port] , %[n2]" "\n\t" // 1 PORT = n2
"ld %[byte] , %a[ptr]+" "\n\t" // 2 b = *ptr++
"sbrc %[byte] , 7" "\n\t" // 1-2 if(b & 0x80)
"mov %[n1] , %[hi]" "\n\t" // 0-1 n1 = hi
"out %[port] , %[lo]" "\n\t" // 1 PORT = lo
"brne headD" "\n" // 2 while(i) (Z flag set above)
: [byte] "+r" (b),
[n1] "+r" (n1),
[n2] "+r" (n2),
[count] "+w" (i)
: [port] "I" (_SFR_IO_ADDR(PORTD)),
[ptr] "e" (ptr),
[hi] "r" (hi),
[lo] "r" (lo));
#if defined(PORTB) || defined(PORTC) || defined(PORTF)
} else // other PORT(s)
#endif // defined(PORTB/C/F)
#endif // defined(PORTD)
// PORTB OUTPUT ----------------------------------------------------
#if defined(PORTB)
#if defined(PORTD) || defined(PORTC) || defined(PORTF)
if(port == &PORTB) {
#endif // defined(PORTD/C/F)
// Same as above, just switched to PORTB and stripped of comments.
hi = PORTB | pinMask;
lo = PORTB & ~pinMask;
n1 = lo;
if(b & 0x80) n1 = hi;
asm volatile(
"headB:" "\n\t"
"out %[port] , %[hi]" "\n\t"
"mov %[n2] , %[lo]" "\n\t"
"out %[port] , %[n1]" "\n\t"
"rjmp .+0" "\n\t"
"sbrc %[byte] , 6" "\n\t"
"mov %[n2] , %[hi]" "\n\t"
"out %[port] , %[lo]" "\n\t"
"rjmp .+0" "\n\t"
"out %[port] , %[hi]" "\n\t"
"mov %[n1] , %[lo]" "\n\t"
"out %[port] , %[n2]" "\n\t"
"rjmp .+0" "\n\t"
"sbrc %[byte] , 5" "\n\t"
"mov %[n1] , %[hi]" "\n\t"
"out %[port] , %[lo]" "\n\t"
"rjmp .+0" "\n\t"
"out %[port] , %[hi]" "\n\t"
"mov %[n2] , %[lo]" "\n\t"
"out %[port] , %[n1]" "\n\t"
"rjmp .+0" "\n\t"
"sbrc %[byte] , 4" "\n\t"
"mov %[n2] , %[hi]" "\n\t"
"out %[port] , %[lo]" "\n\t"
"rjmp .+0" "\n\t"
"out %[port] , %[hi]" "\n\t"
"mov %[n1] , %[lo]" "\n\t"
"out %[port] , %[n2]" "\n\t"
"rjmp .+0" "\n\t"
"sbrc %[byte] , 3" "\n\t"
"mov %[n1] , %[hi]" "\n\t"
"out %[port] , %[lo]" "\n\t"
"rjmp .+0" "\n\t"
"out %[port] , %[hi]" "\n\t"
"mov %[n2] , %[lo]" "\n\t"
"out %[port] , %[n1]" "\n\t"
"rjmp .+0" "\n\t"
"sbrc %[byte] , 2" "\n\t"
"mov %[n2] , %[hi]" "\n\t"
"out %[port] , %[lo]" "\n\t"
"rjmp .+0" "\n\t"
"out %[port] , %[hi]" "\n\t"
"mov %[n1] , %[lo]" "\n\t"
"out %[port] , %[n2]" "\n\t"
"rjmp .+0" "\n\t"
"sbrc %[byte] , 1" "\n\t"
"mov %[n1] , %[hi]" "\n\t"
"out %[port] , %[lo]" "\n\t"
"rjmp .+0" "\n\t"
"out %[port] , %[hi]" "\n\t"
"mov %[n2] , %[lo]" "\n\t"
"out %[port] , %[n1]" "\n\t"
"rjmp .+0" "\n\t"
"sbrc %[byte] , 0" "\n\t"
"mov %[n2] , %[hi]" "\n\t"
"out %[port] , %[lo]" "\n\t"
"sbiw %[count], 1" "\n\t"
"out %[port] , %[hi]" "\n\t"
"mov %[n1] , %[lo]" "\n\t"
"out %[port] , %[n2]" "\n\t"
"ld %[byte] , %a[ptr]+" "\n\t"
"sbrc %[byte] , 7" "\n\t"
"mov %[n1] , %[hi]" "\n\t"
"out %[port] , %[lo]" "\n\t"
"brne headB" "\n"
: [byte] "+r" (b), [n1] "+r" (n1), [n2] "+r" (n2), [count] "+w" (i)
: [port] "I" (_SFR_IO_ADDR(PORTB)), [ptr] "e" (ptr), [hi] "r" (hi),
[lo] "r" (lo));
#if defined(PORTD) || defined(PORTC) || defined(PORTF)
}
#endif
#if defined(PORTC) || defined(PORTF)
else
#endif // defined(PORTC/F)
#endif // defined(PORTB)
// PORTC OUTPUT ----------------------------------------------------
#if defined(PORTC)
#if defined(PORTD) || defined(PORTB) || defined(PORTF)
if(port == &PORTC) {
#endif // defined(PORTD/B/F)
// Same as above, just switched to PORTC and stripped of comments.
hi = PORTC | pinMask;
lo = PORTC & ~pinMask;
n1 = lo;
if(b & 0x80) n1 = hi;
asm volatile(
"headC:" "\n\t"
"out %[port] , %[hi]" "\n\t"
"mov %[n2] , %[lo]" "\n\t"
"out %[port] , %[n1]" "\n\t"
"rjmp .+0" "\n\t"
"sbrc %[byte] , 6" "\n\t"
"mov %[n2] , %[hi]" "\n\t"
"out %[port] , %[lo]" "\n\t"
"rjmp .+0" "\n\t"
"out %[port] , %[hi]" "\n\t"
"mov %[n1] , %[lo]" "\n\t"
"out %[port] , %[n2]" "\n\t"
"rjmp .+0" "\n\t"
"sbrc %[byte] , 5" "\n\t"
"mov %[n1] , %[hi]" "\n\t"
"out %[port] , %[lo]" "\n\t"
"rjmp .+0" "\n\t"
"out %[port] , %[hi]" "\n\t"
"mov %[n2] , %[lo]" "\n\t"
"out %[port] , %[n1]" "\n\t"
"rjmp .+0" "\n\t"
"sbrc %[byte] , 4" "\n\t"
"mov %[n2] , %[hi]" "\n\t"
"out %[port] , %[lo]" "\n\t"
"rjmp .+0" "\n\t"
"out %[port] , %[hi]" "\n\t"
"mov %[n1] , %[lo]" "\n\t"
"out %[port] , %[n2]" "\n\t"
"rjmp .+0" "\n\t"
"sbrc %[byte] , 3" "\n\t"
"mov %[n1] , %[hi]" "\n\t"
"out %[port] , %[lo]" "\n\t"
"rjmp .+0" "\n\t"
"out %[port] , %[hi]" "\n\t"
"mov %[n2] , %[lo]" "\n\t"
"out %[port] , %[n1]" "\n\t"
"rjmp .+0" "\n\t"
"sbrc %[byte] , 2" "\n\t"
"mov %[n2] , %[hi]" "\n\t"
"out %[port] , %[lo]" "\n\t"
"rjmp .+0" "\n\t"
"out %[port] , %[hi]" "\n\t"
"mov %[n1] , %[lo]" "\n\t"
"out %[port] , %[n2]" "\n\t"
"rjmp .+0" "\n\t"
"sbrc %[byte] , 1" "\n\t"
"mov %[n1] , %[hi]" "\n\t"
"out %[port] , %[lo]" "\n\t"
"rjmp .+0" "\n\t"
"out %[port] , %[hi]" "\n\t"
"mov %[n2] , %[lo]" "\n\t"
"out %[port] , %[n1]" "\n\t"
"rjmp .+0" "\n\t"
"sbrc %[byte] , 0" "\n\t"
"mov %[n2] , %[hi]" "\n\t"
"out %[port] , %[lo]" "\n\t"
"sbiw %[count], 1" "\n\t"
"out %[port] , %[hi]" "\n\t"
"mov %[n1] , %[lo]" "\n\t"
"out %[port] , %[n2]" "\n\t"
"ld %[byte] , %a[ptr]+" "\n\t"
"sbrc %[byte] , 7" "\n\t"
"mov %[n1] , %[hi]" "\n\t"
"out %[port] , %[lo]" "\n\t"
"brne headC" "\n"
: [byte] "+r" (b), [n1] "+r" (n1), [n2] "+r" (n2), [count] "+w" (i)
: [port] "I" (_SFR_IO_ADDR(PORTC)), [ptr] "e" (ptr), [hi] "r" (hi),
[lo] "r" (lo));
#if defined(PORTD) || defined(PORTB) || defined(PORTF)
}
#endif // defined(PORTD/B/F)
#if defined(PORTF)
else
#endif
#endif // defined(PORTC)
// PORTF OUTPUT ----------------------------------------------------
#if defined(PORTF)
#if defined(PORTD) || defined(PORTB) || defined(PORTC)
if(port == &PORTF) {
#endif // defined(PORTD/B/C)
hi = PORTF | pinMask;
lo = PORTF & ~pinMask;
n1 = lo;
if(b & 0x80) n1 = hi;
asm volatile(
"headF:" "\n\t"
"out %[port] , %[hi]" "\n\t"
"mov %[n2] , %[lo]" "\n\t"
"out %[port] , %[n1]" "\n\t"
"rjmp .+0" "\n\t"
"sbrc %[byte] , 6" "\n\t"
"mov %[n2] , %[hi]" "\n\t"
"out %[port] , %[lo]" "\n\t"
"rjmp .+0" "\n\t"
"out %[port] , %[hi]" "\n\t"
"mov %[n1] , %[lo]" "\n\t"
"out %[port] , %[n2]" "\n\t"
"rjmp .+0" "\n\t"
"sbrc %[byte] , 5" "\n\t"
"mov %[n1] , %[hi]" "\n\t"
"out %[port] , %[lo]" "\n\t"
"rjmp .+0" "\n\t"
"out %[port] , %[hi]" "\n\t"
"mov %[n2] , %[lo]" "\n\t"
"out %[port] , %[n1]" "\n\t"
"rjmp .+0" "\n\t"
"sbrc %[byte] , 4" "\n\t"
"mov %[n2] , %[hi]" "\n\t"
"out %[port] , %[lo]" "\n\t"
"rjmp .+0" "\n\t"
"out %[port] , %[hi]" "\n\t"
"mov %[n1] , %[lo]" "\n\t"
"out %[port] , %[n2]" "\n\t"
"rjmp .+0" "\n\t"
"sbrc %[byte] , 3" "\n\t"
"mov %[n1] , %[hi]" "\n\t"
"out %[port] , %[lo]" "\n\t"
"rjmp .+0" "\n\t"
"out %[port] , %[hi]" "\n\t"
"mov %[n2] , %[lo]" "\n\t"
"out %[port] , %[n1]" "\n\t"
"rjmp .+0" "\n\t"
"sbrc %[byte] , 2" "\n\t"
"mov %[n2] , %[hi]" "\n\t"
"out %[port] , %[lo]" "\n\t"
"rjmp .+0" "\n\t"
"out %[port] , %[hi]" "\n\t"
"mov %[n1] , %[lo]" "\n\t"
"out %[port] , %[n2]" "\n\t"
"rjmp .+0" "\n\t"
"sbrc %[byte] , 1" "\n\t"
"mov %[n1] , %[hi]" "\n\t"
"out %[port] , %[lo]" "\n\t"
"rjmp .+0" "\n\t"
"out %[port] , %[hi]" "\n\t"
"mov %[n2] , %[lo]" "\n\t"
"out %[port] , %[n1]" "\n\t"
"rjmp .+0" "\n\t"
"sbrc %[byte] , 0" "\n\t"
"mov %[n2] , %[hi]" "\n\t"
"out %[port] , %[lo]" "\n\t"
"sbiw %[count], 1" "\n\t"
"out %[port] , %[hi]" "\n\t"
"mov %[n1] , %[lo]" "\n\t"
"out %[port] , %[n2]" "\n\t"
"ld %[byte] , %a[ptr]+" "\n\t"
"sbrc %[byte] , 7" "\n\t"
"mov %[n1] , %[hi]" "\n\t"
"out %[port] , %[lo]" "\n\t"
"brne headF" "\n"
: [byte] "+r" (b), [n1] "+r" (n1), [n2] "+r" (n2), [count] "+w" (i)
: [port] "I" (_SFR_IO_ADDR(PORTF)), [ptr] "e" (ptr), [hi] "r" (hi),
[lo] "r" (lo));
#if defined(PORTD) || defined(PORTB) || defined(PORTC)
}
#endif // defined(PORTD/B/C)
#endif // defined(PORTF)
#ifdef NEO_KHZ400
} else { // end 800 KHz, do 400 KHz
// Timing is more relaxed; unrolling the inner loop for each bit is
// not necessary. Still using the peculiar RJMPs as 2X NOPs, not out
// of need but just to trim the code size down a little.
// This 400-KHz-datastream-on-8-MHz-CPU code is not quite identical
// to the 800-on-16 code later -- the hi/lo timing between WS2811 and
// WS2812 is not simply a 2:1 scale!
// 20 inst. clocks per bit: HHHHxxxxxxLLLLLLLLLL
// ST instructions: ^ ^ ^ (T=0,4,10)
volatile uint8_t next, bit;
hi = *port | pinMask;
lo = *port & ~pinMask;
next = lo;
bit = 8;
asm volatile(
"head20:" "\n\t" // Clk Pseudocode (T = 0)
"st %a[port], %[hi]" "\n\t" // 2 PORT = hi (T = 2)
"sbrc %[byte] , 7" "\n\t" // 1-2 if(b & 128)
"mov %[next], %[hi]" "\n\t" // 0-1 next = hi (T = 4)
"st %a[port], %[next]" "\n\t" // 2 PORT = next (T = 6)
"mov %[next] , %[lo]" "\n\t" // 1 next = lo (T = 7)
"dec %[bit]" "\n\t" // 1 bit-- (T = 8)
"breq nextbyte20" "\n\t" // 1-2 if(bit == 0)
"rol %[byte]" "\n\t" // 1 b <<= 1 (T = 10)
"st %a[port], %[lo]" "\n\t" // 2 PORT = lo (T = 12)
"rjmp .+0" "\n\t" // 2 nop nop (T = 14)
"rjmp .+0" "\n\t" // 2 nop nop (T = 16)
"rjmp .+0" "\n\t" // 2 nop nop (T = 18)
"rjmp head20" "\n\t" // 2 -> head20 (next bit out)
"nextbyte20:" "\n\t" // (T = 10)
"st %a[port], %[lo]" "\n\t" // 2 PORT = lo (T = 12)
"nop" "\n\t" // 1 nop (T = 13)
"ldi %[bit] , 8" "\n\t" // 1 bit = 8 (T = 14)
"ld %[byte] , %a[ptr]+" "\n\t" // 2 b = *ptr++ (T = 16)
"sbiw %[count], 1" "\n\t" // 2 i-- (T = 18)
"brne head20" "\n" // 2 if(i != 0) -> (next byte)
: [port] "+e" (port),
[byte] "+r" (b),
[bit] "+r" (bit),
[next] "+r" (next),
[count] "+w" (i)
: [hi] "r" (hi),
[lo] "r" (lo),
[ptr] "e" (ptr));
}
#endif // NEO_KHZ400
// 12 MHz(ish) AVR --------------------------------------------------------
#elif (F_CPU >= 11100000UL) && (F_CPU <= 14300000UL)
#ifdef NEO_KHZ400 // 800 KHz check needed only if 400 KHz support enabled
if(is800KHz) {
#endif
// In the 12 MHz case, an optimized 800 KHz datastream (no dead time
// between bytes) requires a PORT-specific loop similar to the 8 MHz
// code (but a little more relaxed in this case).
// 15 instruction clocks per bit: HHHHxxxxxxLLLLL
// OUT instructions: ^ ^ ^ (T=0,4,10)
volatile uint8_t next;
// PORTD OUTPUT ----------------------------------------------------
#if defined(PORTD)
#if defined(PORTB) || defined(PORTC) || defined(PORTF)
if(port == &PORTD) {
#endif // defined(PORTB/C/F)
hi = PORTD | pinMask;
lo = PORTD & ~pinMask;
next = lo;
if(b & 0x80) next = hi;
// Don't "optimize" the OUT calls into the bitTime subroutine;
// we're exploiting the RCALL and RET as 3- and 4-cycle NOPs!
asm volatile(
"headD:" "\n\t" // (T = 0)
"out %[port], %[hi]" "\n\t" // (T = 1)
"rcall bitTimeD" "\n\t" // Bit 7 (T = 15)
"out %[port], %[hi]" "\n\t"
"rcall bitTimeD" "\n\t" // Bit 6
"out %[port], %[hi]" "\n\t"
"rcall bitTimeD" "\n\t" // Bit 5
"out %[port], %[hi]" "\n\t"
"rcall bitTimeD" "\n\t" // Bit 4
"out %[port], %[hi]" "\n\t"
"rcall bitTimeD" "\n\t" // Bit 3
"out %[port], %[hi]" "\n\t"
"rcall bitTimeD" "\n\t" // Bit 2
"out %[port], %[hi]" "\n\t"
"rcall bitTimeD" "\n\t" // Bit 1
// Bit 0:
"out %[port] , %[hi]" "\n\t" // 1 PORT = hi (T = 1)
"rjmp .+0" "\n\t" // 2 nop nop (T = 3)
"ld %[byte] , %a[ptr]+" "\n\t" // 2 b = *ptr++ (T = 5)
"out %[port] , %[next]" "\n\t" // 1 PORT = next (T = 6)
"mov %[next] , %[lo]" "\n\t" // 1 next = lo (T = 7)
"sbrc %[byte] , 7" "\n\t" // 1-2 if(b & 0x80) (T = 8)
"mov %[next] , %[hi]" "\n\t" // 0-1 next = hi (T = 9)
"nop" "\n\t" // 1 (T = 10)
"out %[port] , %[lo]" "\n\t" // 1 PORT = lo (T = 11)
"sbiw %[count], 1" "\n\t" // 2 i-- (T = 13)
"brne headD" "\n\t" // 2 if(i != 0) -> (next byte)
"rjmp doneD" "\n\t"
"bitTimeD:" "\n\t" // nop nop nop (T = 4)
"out %[port], %[next]" "\n\t" // 1 PORT = next (T = 5)
"mov %[next], %[lo]" "\n\t" // 1 next = lo (T = 6)
"rol %[byte]" "\n\t" // 1 b <<= 1 (T = 7)
"sbrc %[byte], 7" "\n\t" // 1-2 if(b & 0x80) (T = 8)
"mov %[next], %[hi]" "\n\t" // 0-1 next = hi (T = 9)
"nop" "\n\t" // 1 (T = 10)
"out %[port], %[lo]" "\n\t" // 1 PORT = lo (T = 11)
"ret" "\n\t" // 4 nop nop nop nop (T = 15)
"doneD:" "\n"
: [byte] "+r" (b),
[next] "+r" (next),
[count] "+w" (i)
: [port] "I" (_SFR_IO_ADDR(PORTD)),
[ptr] "e" (ptr),
[hi] "r" (hi),
[lo] "r" (lo));
#if defined(PORTB) || defined(PORTC) || defined(PORTF)
} else // other PORT(s)
#endif // defined(PORTB/C/F)
#endif // defined(PORTD)
// PORTB OUTPUT ----------------------------------------------------
#if defined(PORTB)
#if defined(PORTD) || defined(PORTC) || defined(PORTF)
if(port == &PORTB) {
#endif // defined(PORTD/C/F)
hi = PORTB | pinMask;
lo = PORTB & ~pinMask;
next = lo;
if(b & 0x80) next = hi;
// Same as above, just set for PORTB & stripped of comments
asm volatile(
"headB:" "\n\t"
"out %[port], %[hi]" "\n\t"
"rcall bitTimeB" "\n\t"
"out %[port], %[hi]" "\n\t"
"rcall bitTimeB" "\n\t"
"out %[port], %[hi]" "\n\t"
"rcall bitTimeB" "\n\t"
"out %[port], %[hi]" "\n\t"
"rcall bitTimeB" "\n\t"
"out %[port], %[hi]" "\n\t"
"rcall bitTimeB" "\n\t"
"out %[port], %[hi]" "\n\t"
"rcall bitTimeB" "\n\t"
"out %[port], %[hi]" "\n\t"
"rcall bitTimeB" "\n\t"
"out %[port] , %[hi]" "\n\t"
"rjmp .+0" "\n\t"
"ld %[byte] , %a[ptr]+" "\n\t"
"out %[port] , %[next]" "\n\t"
"mov %[next] , %[lo]" "\n\t"
"sbrc %[byte] , 7" "\n\t"
"mov %[next] , %[hi]" "\n\t"
"nop" "\n\t"
"out %[port] , %[lo]" "\n\t"
"sbiw %[count], 1" "\n\t"
"brne headB" "\n\t"
"rjmp doneB" "\n\t"
"bitTimeB:" "\n\t"
"out %[port], %[next]" "\n\t"
"mov %[next], %[lo]" "\n\t"
"rol %[byte]" "\n\t"
"sbrc %[byte], 7" "\n\t"
"mov %[next], %[hi]" "\n\t"
"nop" "\n\t"
"out %[port], %[lo]" "\n\t"
"ret" "\n\t"
"doneB:" "\n"
: [byte] "+r" (b), [next] "+r" (next), [count] "+w" (i)
: [port] "I" (_SFR_IO_ADDR(PORTB)), [ptr] "e" (ptr), [hi] "r" (hi),
[lo] "r" (lo));
#if defined(PORTD) || defined(PORTC) || defined(PORTF)
}
#endif
#if defined(PORTC) || defined(PORTF)
else
#endif // defined(PORTC/F)
#endif // defined(PORTB)
// PORTC OUTPUT ----------------------------------------------------
#if defined(PORTC)
#if defined(PORTD) || defined(PORTB) || defined(PORTF)
if(port == &PORTC) {
#endif // defined(PORTD/B/F)
hi = PORTC | pinMask;
lo = PORTC & ~pinMask;
next = lo;
if(b & 0x80) next = hi;
// Same as above, just set for PORTC & stripped of comments
asm volatile(
"headC:" "\n\t"
"out %[port], %[hi]" "\n\t"
"rcall bitTimeC" "\n\t"
"out %[port], %[hi]" "\n\t"
"rcall bitTimeC" "\n\t"
"out %[port], %[hi]" "\n\t"
"rcall bitTimeC" "\n\t"
"out %[port], %[hi]" "\n\t"
"rcall bitTimeC" "\n\t"
"out %[port], %[hi]" "\n\t"
"rcall bitTimeC" "\n\t"
"out %[port], %[hi]" "\n\t"
"rcall bitTimeC" "\n\t"
"out %[port], %[hi]" "\n\t"
"rcall bitTimeC" "\n\t"
"out %[port] , %[hi]" "\n\t"
"rjmp .+0" "\n\t"
"ld %[byte] , %a[ptr]+" "\n\t"
"out %[port] , %[next]" "\n\t"
"mov %[next] , %[lo]" "\n\t"
"sbrc %[byte] , 7" "\n\t"
"mov %[next] , %[hi]" "\n\t"
"nop" "\n\t"
"out %[port] , %[lo]" "\n\t"
"sbiw %[count], 1" "\n\t"
"brne headC" "\n\t"
"rjmp doneC" "\n\t"
"bitTimeC:" "\n\t"
"out %[port], %[next]" "\n\t"
"mov %[next], %[lo]" "\n\t"
"rol %[byte]" "\n\t"
"sbrc %[byte], 7" "\n\t"
"mov %[next], %[hi]" "\n\t"
"nop" "\n\t"
"out %[port], %[lo]" "\n\t"
"ret" "\n\t"
"doneC:" "\n"
: [byte] "+r" (b), [next] "+r" (next), [count] "+w" (i)
: [port] "I" (_SFR_IO_ADDR(PORTC)), [ptr] "e" (ptr), [hi] "r" (hi),
[lo] "r" (lo));
#if defined(PORTD) || defined(PORTB) || defined(PORTF)
}
#endif // defined(PORTD/B/F)
#if defined(PORTF)
else
#endif
#endif // defined(PORTC)
// PORTF OUTPUT ----------------------------------------------------
#if defined(PORTF)
#if defined(PORTD) || defined(PORTB) || defined(PORTC)
if(port == &PORTF) {
#endif // defined(PORTD/B/C)
hi = PORTF | pinMask;
lo = PORTF & ~pinMask;
next = lo;
if(b & 0x80) next = hi;
// Same as above, just set for PORTF & stripped of comments
asm volatile(
"headF:" "\n\t"
"out %[port], %[hi]" "\n\t"
"rcall bitTimeC" "\n\t"
"out %[port], %[hi]" "\n\t"
"rcall bitTimeC" "\n\t"
"out %[port], %[hi]" "\n\t"
"rcall bitTimeC" "\n\t"
"out %[port], %[hi]" "\n\t"
"rcall bitTimeC" "\n\t"
"out %[port], %[hi]" "\n\t"
"rcall bitTimeC" "\n\t"
"out %[port], %[hi]" "\n\t"
"rcall bitTimeC" "\n\t"
"out %[port], %[hi]" "\n\t"
"rcall bitTimeC" "\n\t"
"out %[port] , %[hi]" "\n\t"
"rjmp .+0" "\n\t"
"ld %[byte] , %a[ptr]+" "\n\t"
"out %[port] , %[next]" "\n\t"
"mov %[next] , %[lo]" "\n\t"
"sbrc %[byte] , 7" "\n\t"
"mov %[next] , %[hi]" "\n\t"
"nop" "\n\t"
"out %[port] , %[lo]" "\n\t"
"sbiw %[count], 1" "\n\t"
"brne headF" "\n\t"
"rjmp doneC" "\n\t"
"bitTimeC:" "\n\t"
"out %[port], %[next]" "\n\t"
"mov %[next], %[lo]" "\n\t"
"rol %[byte]" "\n\t"
"sbrc %[byte], 7" "\n\t"
"mov %[next], %[hi]" "\n\t"
"nop" "\n\t"
"out %[port], %[lo]" "\n\t"
"ret" "\n\t"
"doneC:" "\n"
: [byte] "+r" (b), [next] "+r" (next), [count] "+w" (i)
: [port] "I" (_SFR_IO_ADDR(PORTF)), [ptr] "e" (ptr), [hi] "r" (hi),
[lo] "r" (lo));
#if defined(PORTD) || defined(PORTB) || defined(PORTC)
}
#endif // defined(PORTD/B/C)
#endif // defined(PORTF)
#ifdef NEO_KHZ400
} else { // 400 KHz
// 30 instruction clocks per bit: HHHHHHxxxxxxxxxLLLLLLLLLLLLLLL
// ST instructions: ^ ^ ^ (T=0,6,15)
volatile uint8_t next, bit;
hi = *port | pinMask;
lo = *port & ~pinMask;
next = lo;
bit = 8;
asm volatile(
"head30:" "\n\t" // Clk Pseudocode (T = 0)
"st %a[port], %[hi]" "\n\t" // 2 PORT = hi (T = 2)
"sbrc %[byte] , 7" "\n\t" // 1-2 if(b & 128)
"mov %[next], %[hi]" "\n\t" // 0-1 next = hi (T = 4)
"rjmp .+0" "\n\t" // 2 nop nop (T = 6)
"st %a[port], %[next]" "\n\t" // 2 PORT = next (T = 8)
"rjmp .+0" "\n\t" // 2 nop nop (T = 10)
"rjmp .+0" "\n\t" // 2 nop nop (T = 12)
"rjmp .+0" "\n\t" // 2 nop nop (T = 14)
"nop" "\n\t" // 1 nop (T = 15)
"st %a[port], %[lo]" "\n\t" // 2 PORT = lo (T = 17)
"rjmp .+0" "\n\t" // 2 nop nop (T = 19)
"dec %[bit]" "\n\t" // 1 bit-- (T = 20)
"breq nextbyte30" "\n\t" // 1-2 if(bit == 0)
"rol %[byte]" "\n\t" // 1 b <<= 1 (T = 22)
"rjmp .+0" "\n\t" // 2 nop nop (T = 24)
"rjmp .+0" "\n\t" // 2 nop nop (T = 26)
"rjmp .+0" "\n\t" // 2 nop nop (T = 28)
"rjmp head30" "\n\t" // 2 -> head30 (next bit out)
"nextbyte30:" "\n\t" // (T = 22)
"nop" "\n\t" // 1 nop (T = 23)
"ldi %[bit] , 8" "\n\t" // 1 bit = 8 (T = 24)
"ld %[byte] , %a[ptr]+" "\n\t" // 2 b = *ptr++ (T = 26)
"sbiw %[count], 1" "\n\t" // 2 i-- (T = 28)
"brne head30" "\n" // 1-2 if(i != 0) -> (next byte)
: [port] "+e" (port),
[byte] "+r" (b),
[bit] "+r" (bit),
[next] "+r" (next),
[count] "+w" (i)
: [hi] "r" (hi),
[lo] "r" (lo),
[ptr] "e" (ptr));
}
#endif // NEO_KHZ400
// 16 MHz(ish) AVR --------------------------------------------------------
#elif (F_CPU >= 15400000UL) && (F_CPU <= 19000000L)
#ifdef NEO_KHZ400 // 800 KHz check needed only if 400 KHz support enabled
if(is800KHz) {
#endif
// WS2811 and WS2812 have different hi/lo duty cycles; this is
// similar but NOT an exact copy of the prior 400-on-8 code.
// 20 inst. clocks per bit: HHHHHxxxxxxxxLLLLLLL
// ST instructions: ^ ^ ^ (T=0,5,13)
volatile uint8_t next, bit;
hi = *port | pinMask;
lo = *port & ~pinMask;
next = lo;
bit = 8;
asm volatile(
"head20:" "\n\t" // Clk Pseudocode (T = 0)
"st %a[port], %[hi]" "\n\t" // 2 PORT = hi (T = 2)
"sbrc %[byte], 7" "\n\t" // 1-2 if(b & 128)
"mov %[next], %[hi]" "\n\t" // 0-1 next = hi (T = 4)
"dec %[bit]" "\n\t" // 1 bit-- (T = 5)
"st %a[port], %[next]" "\n\t" // 2 PORT = next (T = 7)
"mov %[next] , %[lo]" "\n\t" // 1 next = lo (T = 8)
"breq nextbyte20" "\n\t" // 1-2 if(bit == 0) (from dec above)
"rol %[byte]" "\n\t" // 1 b <<= 1 (T = 10)
"rjmp .+0" "\n\t" // 2 nop nop (T = 12)
"nop" "\n\t" // 1 nop (T = 13)
"st %a[port], %[lo]" "\n\t" // 2 PORT = lo (T = 15)
"nop" "\n\t" // 1 nop (T = 16)
"rjmp .+0" "\n\t" // 2 nop nop (T = 18)
"rjmp head20" "\n\t" // 2 -> head20 (next bit out)
"nextbyte20:" "\n\t" // (T = 10)
"ldi %[bit] , 8" "\n\t" // 1 bit = 8 (T = 11)
"ld %[byte] , %a[ptr]+" "\n\t" // 2 b = *ptr++ (T = 13)
"st %a[port], %[lo]" "\n\t" // 2 PORT = lo (T = 15)
"nop" "\n\t" // 1 nop (T = 16)
"sbiw %[count], 1" "\n\t" // 2 i-- (T = 18)
"brne head20" "\n" // 2 if(i != 0) -> (next byte)
: [port] "+e" (port),
[byte] "+r" (b),
[bit] "+r" (bit),
[next] "+r" (next),
[count] "+w" (i)
: [ptr] "e" (ptr),
[hi] "r" (hi),
[lo] "r" (lo));
#ifdef NEO_KHZ400
} else { // 400 KHz
// The 400 KHz clock on 16 MHz MCU is the most 'relaxed' version.
// 40 inst. clocks per bit: HHHHHHHHxxxxxxxxxxxxLLLLLLLLLLLLLLLLLLLL
// ST instructions: ^ ^ ^ (T=0,8,20)
volatile uint8_t next, bit;
hi = *port | pinMask;
lo = *port & ~pinMask;
next = lo;
bit = 8;
asm volatile(
"head40:" "\n\t" // Clk Pseudocode (T = 0)
"st %a[port], %[hi]" "\n\t" // 2 PORT = hi (T = 2)
"sbrc %[byte] , 7" "\n\t" // 1-2 if(b & 128)
"mov %[next] , %[hi]" "\n\t" // 0-1 next = hi (T = 4)
"rjmp .+0" "\n\t" // 2 nop nop (T = 6)
"rjmp .+0" "\n\t" // 2 nop nop (T = 8)
"st %a[port], %[next]" "\n\t" // 2 PORT = next (T = 10)
"rjmp .+0" "\n\t" // 2 nop nop (T = 12)
"rjmp .+0" "\n\t" // 2 nop nop (T = 14)
"rjmp .+0" "\n\t" // 2 nop nop (T = 16)
"rjmp .+0" "\n\t" // 2 nop nop (T = 18)
"rjmp .+0" "\n\t" // 2 nop nop (T = 20)
"st %a[port], %[lo]" "\n\t" // 2 PORT = lo (T = 22)
"nop" "\n\t" // 1 nop (T = 23)
"mov %[next] , %[lo]" "\n\t" // 1 next = lo (T = 24)
"dec %[bit]" "\n\t" // 1 bit-- (T = 25)
"breq nextbyte40" "\n\t" // 1-2 if(bit == 0)
"rol %[byte]" "\n\t" // 1 b <<= 1 (T = 27)
"nop" "\n\t" // 1 nop (T = 28)
"rjmp .+0" "\n\t" // 2 nop nop (T = 30)
"rjmp .+0" "\n\t" // 2 nop nop (T = 32)
"rjmp .+0" "\n\t" // 2 nop nop (T = 34)
"rjmp .+0" "\n\t" // 2 nop nop (T = 36)
"rjmp .+0" "\n\t" // 2 nop nop (T = 38)
"rjmp head40" "\n\t" // 2 -> head40 (next bit out)
"nextbyte40:" "\n\t" // (T = 27)
"ldi %[bit] , 8" "\n\t" // 1 bit = 8 (T = 28)
"ld %[byte] , %a[ptr]+" "\n\t" // 2 b = *ptr++ (T = 30)
"rjmp .+0" "\n\t" // 2 nop nop (T = 32)
"st %a[port], %[lo]" "\n\t" // 2 PORT = lo (T = 34)
"rjmp .+0" "\n\t" // 2 nop nop (T = 36)
"sbiw %[count], 1" "\n\t" // 2 i-- (T = 38)
"brne head40" "\n" // 1-2 if(i != 0) -> (next byte)
: [port] "+e" (port),
[byte] "+r" (b),
[bit] "+r" (bit),
[next] "+r" (next),
[count] "+w" (i)
: [ptr] "e" (ptr),
[hi] "r" (hi),
[lo] "r" (lo));
}
#endif // NEO_KHZ400
#else
#error "CPU SPEED NOT SUPPORTED"
#endif // end F_CPU ifdefs on __AVR__
// END AVR ----------------------------------------------------------------
#elif defined(__arm__)
// ARM MCUs -- Teensy 3.0, 3.1, LC, Arduino Due ---------------------------
#if defined(TEENSYDUINO) && defined(KINETISK) // Teensy 3.0, 3.1, 3.2, 3.5, 3.6
#define CYCLES_800_T0H (F_CPU / 4000000)
#define CYCLES_800_T1H (F_CPU / 1250000)
#define CYCLES_800 (F_CPU / 800000)
#define CYCLES_400_T0H (F_CPU / 2000000)
#define CYCLES_400_T1H (F_CPU / 833333)
#define CYCLES_400 (F_CPU / 400000)
uint8_t *p = pixels,
*end = p + numBytes, pix, mask;
volatile uint8_t *set = portSetRegister(pin),
*clr = portClearRegister(pin);
uint32_t cyc;
ARM_DEMCR |= ARM_DEMCR_TRCENA;
ARM_DWT_CTRL |= ARM_DWT_CTRL_CYCCNTENA;
#ifdef NEO_KHZ400 // 800 KHz check needed only if 400 KHz support enabled
if(is800KHz) {
#endif
cyc = ARM_DWT_CYCCNT + CYCLES_800;
while(p < end) {
pix = *p++;
for(mask = 0x80; mask; mask >>= 1) {
while(ARM_DWT_CYCCNT - cyc < CYCLES_800);
cyc = ARM_DWT_CYCCNT;
*set = 1;
if(pix & mask) {
while(ARM_DWT_CYCCNT - cyc < CYCLES_800_T1H);
} else {
while(ARM_DWT_CYCCNT - cyc < CYCLES_800_T0H);
}
*clr = 1;
}
}
while(ARM_DWT_CYCCNT - cyc < CYCLES_800);
#ifdef NEO_KHZ400
} else { // 400 kHz bitstream
cyc = ARM_DWT_CYCCNT + CYCLES_400;
while(p < end) {
pix = *p++;
for(mask = 0x80; mask; mask >>= 1) {
while(ARM_DWT_CYCCNT - cyc < CYCLES_400);
cyc = ARM_DWT_CYCCNT;
*set = 1;
if(pix & mask) {
while(ARM_DWT_CYCCNT - cyc < CYCLES_400_T1H);
} else {
while(ARM_DWT_CYCCNT - cyc < CYCLES_400_T0H);
}
*clr = 1;
}
}
while(ARM_DWT_CYCCNT - cyc < CYCLES_400);
}
#endif // NEO_KHZ400
#elif defined(TEENSYDUINO) && (defined(__IMXRT1052__) || defined(__IMXRT1062__))
#define CYCLES_800_T0H (F_CPU_ACTUAL / 4000000)
#define CYCLES_800_T1H (F_CPU_ACTUAL / 1250000)
#define CYCLES_800 (F_CPU_ACTUAL / 800000)
#define CYCLES_400_T0H (F_CPU_ACTUAL / 2000000)
#define CYCLES_400_T1H (F_CPU_ACTUAL / 833333)
#define CYCLES_400 (F_CPU_ACTUAL / 400000)
uint8_t *p = pixels,
*end = p + numBytes, pix, mask;
volatile uint32_t *set = portSetRegister(pin),
*clr = portClearRegister(pin);
uint32_t cyc,
msk = digitalPinToBitMask(pin);
ARM_DEMCR |= ARM_DEMCR_TRCENA;
ARM_DWT_CTRL |= ARM_DWT_CTRL_CYCCNTENA;
#ifdef NEO_KHZ400 // 800 KHz check needed only if 400 KHz support enabled
if(is800KHz) {
#endif
cyc = ARM_DWT_CYCCNT + CYCLES_800;
while(p < end) {
pix = *p++;
for(mask = 0x80; mask; mask >>= 1) {
while(ARM_DWT_CYCCNT - cyc < CYCLES_800);
cyc = ARM_DWT_CYCCNT;
*set = msk;
if(pix & mask) {
while(ARM_DWT_CYCCNT - cyc < CYCLES_800_T1H);
} else {
while(ARM_DWT_CYCCNT - cyc < CYCLES_800_T0H);
}
*clr = msk;
}
}
while(ARM_DWT_CYCCNT - cyc < CYCLES_800);
#ifdef NEO_KHZ400
} else { // 400 kHz bitstream
cyc = ARM_DWT_CYCCNT + CYCLES_400;
while(p < end) {
pix = *p++;
for(mask = 0x80; mask; mask >>= 1) {
while(ARM_DWT_CYCCNT - cyc < CYCLES_400);
cyc = ARM_DWT_CYCCNT;
*set = msk;
if(pix & mask) {
while(ARM_DWT_CYCCNT - cyc < CYCLES_400_T1H);
} else {
while(ARM_DWT_CYCCNT - cyc < CYCLES_400_T0H);
}
*clr = msk;
}
}
while(ARM_DWT_CYCCNT - cyc < CYCLES_400);
}
#endif // NEO_KHZ400
#elif defined(TEENSYDUINO) && defined(__MKL26Z64__) // Teensy-LC
#if F_CPU == 48000000
uint8_t *p = pixels,
pix, count, dly,
bitmask = digitalPinToBitMask(pin);
volatile uint8_t *reg = portSetRegister(pin);
uint32_t num = numBytes;
asm volatile(
"L%=_begin:" "\n\t"
"ldrb %[pix], [%[p], #0]" "\n\t"
"lsl %[pix], #24" "\n\t"
"movs %[count], #7" "\n\t"
"L%=_loop:" "\n\t"
"lsl %[pix], #1" "\n\t"
"bcs L%=_loop_one" "\n\t"
"L%=_loop_zero:" "\n\t"
"strb %[bitmask], [%[reg], #0]" "\n\t"
"movs %[dly], #4" "\n\t"
"L%=_loop_delay_T0H:" "\n\t"
"sub %[dly], #1" "\n\t"
"bne L%=_loop_delay_T0H" "\n\t"
"strb %[bitmask], [%[reg], #4]" "\n\t"
"movs %[dly], #13" "\n\t"
"L%=_loop_delay_T0L:" "\n\t"
"sub %[dly], #1" "\n\t"
"bne L%=_loop_delay_T0L" "\n\t"
"b L%=_next" "\n\t"
"L%=_loop_one:" "\n\t"
"strb %[bitmask], [%[reg], #0]" "\n\t"
"movs %[dly], #13" "\n\t"
"L%=_loop_delay_T1H:" "\n\t"
"sub %[dly], #1" "\n\t"
"bne L%=_loop_delay_T1H" "\n\t"
"strb %[bitmask], [%[reg], #4]" "\n\t"
"movs %[dly], #4" "\n\t"
"L%=_loop_delay_T1L:" "\n\t"
"sub %[dly], #1" "\n\t"
"bne L%=_loop_delay_T1L" "\n\t"
"nop" "\n\t"
"L%=_next:" "\n\t"
"sub %[count], #1" "\n\t"
"bne L%=_loop" "\n\t"
"lsl %[pix], #1" "\n\t"
"bcs L%=_last_one" "\n\t"
"L%=_last_zero:" "\n\t"
"strb %[bitmask], [%[reg], #0]" "\n\t"
"movs %[dly], #4" "\n\t"
"L%=_last_delay_T0H:" "\n\t"
"sub %[dly], #1" "\n\t"
"bne L%=_last_delay_T0H" "\n\t"
"strb %[bitmask], [%[reg], #4]" "\n\t"
"movs %[dly], #10" "\n\t"
"L%=_last_delay_T0L:" "\n\t"
"sub %[dly], #1" "\n\t"
"bne L%=_last_delay_T0L" "\n\t"
"b L%=_repeat" "\n\t"
"L%=_last_one:" "\n\t"
"strb %[bitmask], [%[reg], #0]" "\n\t"
"movs %[dly], #13" "\n\t"
"L%=_last_delay_T1H:" "\n\t"
"sub %[dly], #1" "\n\t"
"bne L%=_last_delay_T1H" "\n\t"
"strb %[bitmask], [%[reg], #4]" "\n\t"
"movs %[dly], #1" "\n\t"
"L%=_last_delay_T1L:" "\n\t"
"sub %[dly], #1" "\n\t"
"bne L%=_last_delay_T1L" "\n\t"
"nop" "\n\t"
"L%=_repeat:" "\n\t"
"add %[p], #1" "\n\t"
"sub %[num], #1" "\n\t"
"bne L%=_begin" "\n\t"
"L%=_done:" "\n\t"
: [p] "+r" (p),
[pix] "=&r" (pix),
[count] "=&r" (count),
[dly] "=&r" (dly),
[num] "+r" (num)
: [bitmask] "r" (bitmask),
[reg] "r" (reg)
);
#else
#error "Sorry, only 48 MHz is supported, please set Tools > CPU Speed to 48 MHz"
#endif // F_CPU == 48000000
// Begin of support for nRF52 based boards -------------------------
#elif defined(NRF52) || defined(NRF52_SERIES)
// [[[Begin of the Neopixel NRF52 EasyDMA implementation
// by the Hackerspace San Salvador]]]
// This technique uses the PWM peripheral on the NRF52. The PWM uses the
// EasyDMA feature included on the chip. This technique loads the duty
// cycle configuration for each cycle when the PWM is enabled. For this
// to work we need to store a 16 bit configuration for each bit of the
// RGB(W) values in the pixel buffer.
// Comparator values for the PWM were hand picked and are guaranteed to
// be 100% organic to preserve freshness and high accuracy. Current
// parameters are:
// * PWM Clock: 16Mhz
// * Minimum step time: 62.5ns
// * Time for zero in high (T0H): 0.31ms
// * Time for one in high (T1H): 0.75ms
// * Cycle time: 1.25us
// * Frequency: 800Khz
// For 400Khz we just double the calculated times.
// ---------- BEGIN Constants for the EasyDMA implementation -----------
// The PWM starts the duty cycle in LOW. To start with HIGH we
// need to set the 15th bit on each register.
// WS2812 (rev A) timing is 0.35 and 0.7us
//#define MAGIC_T0H 5UL | (0x8000) // 0.3125us
//#define MAGIC_T1H 12UL | (0x8000) // 0.75us
// WS2812B (rev B) timing is 0.4 and 0.8 us
#define MAGIC_T0H 6UL | (0x8000) // 0.375us
#define MAGIC_T1H 13UL | (0x8000) // 0.8125us
// WS2811 (400 khz) timing is 0.5 and 1.2
#define MAGIC_T0H_400KHz 8UL | (0x8000) // 0.5us
#define MAGIC_T1H_400KHz 19UL | (0x8000) // 1.1875us
// For 400Khz, we double value of CTOPVAL
#define CTOPVAL 20UL // 1.25us
#define CTOPVAL_400KHz 40UL // 2.5us
// ---------- END Constants for the EasyDMA implementation -------------
//
// If there is no device available an alternative cycle-counter
// implementation is tried.
// The nRF52 runs with a fixed clock of 64Mhz. The alternative
// implementation is the same as the one used for the Teensy 3.0/1/2 but
// with the Nordic SDK HAL & registers syntax.
// The number of cycles was hand picked and is guaranteed to be 100%
// organic to preserve freshness and high accuracy.
// ---------- BEGIN Constants for cycle counter implementation ---------
#define CYCLES_800_T0H 18 // ~0.36 uS
#define CYCLES_800_T1H 41 // ~0.76 uS
#define CYCLES_800 71 // ~1.25 uS
#define CYCLES_400_T0H 26 // ~0.50 uS
#define CYCLES_400_T1H 70 // ~1.26 uS
#define CYCLES_400 156 // ~2.50 uS
// ---------- END of Constants for cycle counter implementation --------
// To support both the SoftDevice + Neopixels we use the EasyDMA
// feature from the NRF25. However this technique implies to
// generate a pattern and store it on the memory. The actual
// memory used in bytes corresponds to the following formula:
// totalMem = numBytes*8*2+(2*2)
// The two additional bytes at the end are needed to reset the
// sequence.
//
// If there is not enough memory, we will fall back to cycle counter
// using DWT
uint32_t pattern_size = numBytes*8*sizeof(uint16_t)+2*sizeof(uint16_t);
uint16_t* pixels_pattern = NULL;
NRF_PWM_Type* pwm = NULL;
// Try to find a free PWM device, which is not enabled
// and has no connected pins
NRF_PWM_Type* PWM[] = {
NRF_PWM0, NRF_PWM1, NRF_PWM2
#ifdef NRF_PWM3
,NRF_PWM3
#endif
};
for(int device = 0; device < (sizeof(PWM)/sizeof(PWM[0])); device++) {
if( (PWM[device]->ENABLE == 0) &&
(PWM[device]->PSEL.OUT[0] & PWM_PSEL_OUT_CONNECT_Msk) &&
(PWM[device]->PSEL.OUT[1] & PWM_PSEL_OUT_CONNECT_Msk) &&
(PWM[device]->PSEL.OUT[2] & PWM_PSEL_OUT_CONNECT_Msk) &&
(PWM[device]->PSEL.OUT[3] & PWM_PSEL_OUT_CONNECT_Msk)
) {
pwm = PWM[device];
break;
}
}
// only malloc if there is PWM device available
if ( pwm != NULL ) {
#ifdef ARDUINO_NRF52_ADAFRUIT // use thread-safe malloc
pixels_pattern = (uint16_t *) rtos_malloc(pattern_size);
#else
pixels_pattern = (uint16_t *) malloc(pattern_size);
#endif
}
// Use the identified device to choose the implementation
// If a PWM device is available use DMA
if( (pixels_pattern != NULL) && (pwm != NULL) ) {
uint16_t pos = 0; // bit position
for(uint16_t n=0; n<numBytes; n++) {
uint8_t pix = pixels[n];
for(uint8_t mask=0x80; mask>0; mask >>= 1) {
#ifdef NEO_KHZ400
if( !is800KHz ) {
pixels_pattern[pos] = (pix & mask) ? MAGIC_T1H_400KHz : MAGIC_T0H_400KHz;
}else
#endif
{
pixels_pattern[pos] = (pix & mask) ? MAGIC_T1H : MAGIC_T0H;
}
pos++;
}
}
// Zero padding to indicate the end of que sequence
pixels_pattern[pos++] = 0 | (0x8000); // Seq end
pixels_pattern[pos++] = 0 | (0x8000); // Seq end
// Set the wave mode to count UP
pwm->MODE = (PWM_MODE_UPDOWN_Up << PWM_MODE_UPDOWN_Pos);
// Set the PWM to use the 16MHz clock
pwm->PRESCALER = (PWM_PRESCALER_PRESCALER_DIV_1 << PWM_PRESCALER_PRESCALER_Pos);
// Setting of the maximum count
// but keeping it on 16Mhz allows for more granularity just
// in case someone wants to do more fine-tuning of the timing.
#ifdef NEO_KHZ400
if( !is800KHz ) {
pwm->COUNTERTOP = (CTOPVAL_400KHz << PWM_COUNTERTOP_COUNTERTOP_Pos);
}else
#endif
{
pwm->COUNTERTOP = (CTOPVAL << PWM_COUNTERTOP_COUNTERTOP_Pos);
}
// Disable loops, we want the sequence to repeat only once
pwm->LOOP = (PWM_LOOP_CNT_Disabled << PWM_LOOP_CNT_Pos);
// On the "Common" setting the PWM uses the same pattern for the
// for supported sequences. The pattern is stored on half-word
// of 16bits
pwm->DECODER = (PWM_DECODER_LOAD_Common << PWM_DECODER_LOAD_Pos) |
(PWM_DECODER_MODE_RefreshCount << PWM_DECODER_MODE_Pos);
// Pointer to the memory storing the patter
pwm->SEQ[0].PTR = (uint32_t)(pixels_pattern) << PWM_SEQ_PTR_PTR_Pos;
// Calculation of the number of steps loaded from memory.
pwm->SEQ[0].CNT = (pattern_size/sizeof(uint16_t)) << PWM_SEQ_CNT_CNT_Pos;
// The following settings are ignored with the current config.
pwm->SEQ[0].REFRESH = 0;
pwm->SEQ[0].ENDDELAY = 0;
// The Neopixel implementation is a blocking algorithm. DMA
// allows for non-blocking operation. To "simulate" a blocking
// operation we enable the interruption for the end of sequence
// and block the execution thread until the event flag is set by
// the peripheral.
// pwm->INTEN |= (PWM_INTEN_SEQEND0_Enabled<<PWM_INTEN_SEQEND0_Pos);
// PSEL must be configured before enabling PWM
pwm->PSEL.OUT[0] = g_ADigitalPinMap[pin];
// Enable the PWM
pwm->ENABLE = 1;
// After all of this and many hours of reading the documentation
// we are ready to start the sequence...
pwm->EVENTS_SEQEND[0] = 0;
pwm->TASKS_SEQSTART[0] = 1;
// But we have to wait for the flag to be set.
while(!pwm->EVENTS_SEQEND[0])
{
#ifdef ARDUINO_NRF52_ADAFRUIT
yield();
#endif
}
// Before leave we clear the flag for the event.
pwm->EVENTS_SEQEND[0] = 0;
// We need to disable the device and disconnect
// all the outputs before leave or the device will not
// be selected on the next call.
// TODO: Check if disabling the device causes performance issues.
pwm->ENABLE = 0;
pwm->PSEL.OUT[0] = 0xFFFFFFFFUL;
#ifdef ARDUINO_NRF52_ADAFRUIT // use thread-safe free
rtos_free(pixels_pattern);
#else
free(pixels_pattern);
#endif
}// End of DMA implementation
// ---------------------------------------------------------------------
else{
// Fall back to DWT
#ifdef ARDUINO_NRF52_ADAFRUIT
// Bluefruit Feather 52 uses freeRTOS
// Critical Section is used since it does not block SoftDevice execution
taskENTER_CRITICAL();
#elif defined(NRF52_DISABLE_INT)
// If you are using the Bluetooth SoftDevice we advise you to not disable
// the interrupts. Disabling the interrupts even for short periods of time
// causes the SoftDevice to stop working.
// Disable the interrupts only in cases where you need high performance for
// the LEDs and if you are not using the EasyDMA feature.
__disable_irq();
#endif
NRF_GPIO_Type* nrf_port = (NRF_GPIO_Type*) digitalPinToPort(pin);
uint32_t pinMask = digitalPinToBitMask(pin);
uint32_t CYCLES_X00 = CYCLES_800;
uint32_t CYCLES_X00_T1H = CYCLES_800_T1H;
uint32_t CYCLES_X00_T0H = CYCLES_800_T0H;
#ifdef NEO_KHZ400
if( !is800KHz )
{
CYCLES_X00 = CYCLES_400;
CYCLES_X00_T1H = CYCLES_400_T1H;
CYCLES_X00_T0H = CYCLES_400_T0H;
}
#endif
// Enable DWT in debug core
CoreDebug->DEMCR |= CoreDebug_DEMCR_TRCENA_Msk;
DWT->CTRL |= DWT_CTRL_CYCCNTENA_Msk;
// Tries to re-send the frame if is interrupted by the SoftDevice.
while(1) {
uint8_t *p = pixels;
uint32_t cycStart = DWT->CYCCNT;
uint32_t cyc = 0;
for(uint16_t n=0; n<numBytes; n++) {
uint8_t pix = *p++;
for(uint8_t mask = 0x80; mask; mask >>= 1) {
while(DWT->CYCCNT - cyc < CYCLES_X00);
cyc = DWT->CYCCNT;
nrf_port->OUTSET |= pinMask;
if(pix & mask) {
while(DWT->CYCCNT - cyc < CYCLES_X00_T1H);
} else {
while(DWT->CYCCNT - cyc < CYCLES_X00_T0H);
}
nrf_port->OUTCLR |= pinMask;
}
}
while(DWT->CYCCNT - cyc < CYCLES_X00);
// If total time longer than 25%, resend the whole data.
// Since we are likely to be interrupted by SoftDevice
if ( (DWT->CYCCNT - cycStart) < ( 8*numBytes*((CYCLES_X00*5)/4) ) ) {
break;
}
// re-send need 300us delay
delayMicroseconds(300);
}
// Enable interrupts again
#ifdef ARDUINO_NRF52_ADAFRUIT
taskEXIT_CRITICAL();
#elif defined(NRF52_DISABLE_INT)
__enable_irq();
#endif
}
// END of NRF52 implementation
#elif defined (__SAMD21E17A__) || defined(__SAMD21G18A__) || defined(__SAMD21E18A__) || defined(__SAMD21J18A__) // Arduino Zero, Gemma/Trinket M0, SODAQ Autonomo and others
// Tried this with a timer/counter, couldn't quite get adequate
// resolution. So yay, you get a load of goofball NOPs...
uint8_t *ptr, *end, p, bitMask, portNum;
uint32_t pinMask;
portNum = g_APinDescription[pin].ulPort;
pinMask = 1ul << g_APinDescription[pin].ulPin;
ptr = pixels;
end = ptr + numBytes;
p = *ptr++;
bitMask = 0x80;
volatile uint32_t *set = &(PORT->Group[portNum].OUTSET.reg),
*clr = &(PORT->Group[portNum].OUTCLR.reg);
#ifdef NEO_KHZ400 // 800 KHz check needed only if 400 KHz support enabled
if(is800KHz) {
#endif
for(;;) {
*set = pinMask;
asm("nop; nop; nop; nop; nop; nop; nop; nop;");
if(p & bitMask) {
asm("nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop;");
*clr = pinMask;
} else {
*clr = pinMask;
asm("nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop;");
}
if(bitMask >>= 1) {
asm("nop; nop; nop; nop; nop; nop; nop; nop; nop;");
} else {
if(ptr >= end) break;
p = *ptr++;
bitMask = 0x80;
}
}
#ifdef NEO_KHZ400
} else { // 400 KHz bitstream
for(;;) {
*set = pinMask;
asm("nop; nop; nop; nop; nop; nop; nop; nop; nop; nop; nop;");
if(p & bitMask) {
asm("nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop;");
*clr = pinMask;
} else {
*clr = pinMask;
asm("nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop;");
}
asm("nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;");
if(bitMask >>= 1) {
asm("nop; nop; nop; nop; nop; nop; nop;");
} else {
if(ptr >= end) break;
p = *ptr++;
bitMask = 0x80;
}
}
}
#endif
#elif defined (__SAMD51__) // M4
uint8_t *ptr, *end, p, bitMask, portNum, bit;
uint32_t pinMask;
portNum = g_APinDescription[pin].ulPort;
pinMask = 1ul << g_APinDescription[pin].ulPin;
ptr = pixels;
end = ptr + numBytes;
p = *ptr++;
bitMask = 0x80;
volatile uint32_t *set = &(PORT->Group[portNum].OUTSET.reg),
*clr = &(PORT->Group[portNum].OUTCLR.reg);
// SAMD51 overclock-compatible timing is only a mild abomination.
// It uses SysTick for a consistent clock reference regardless of
// optimization / cache settings. That's the good news. The bad news,
// since SysTick->VAL is a volatile type it's slow to access...and then,
// with the SysTick interval that Arduino sets up (1 ms), this would
// require a subtract and MOD operation for gauging elapsed time, and
// all taken in combination that lacks adequate temporal resolution
// for NeoPixel timing. So a kind of horrible thing is done here...
// since interrupts are turned off anyway and it's generally accepted
// by now that we're gonna lose track of time in the NeoPixel lib,
// the SysTick timer is reconfigured for a period matching the NeoPixel
// bit timing (either 800 or 400 KHz) and we watch SysTick->VAL very
// closely (just a threshold, no subtract or MOD or anything) and that
// seems to work just well enough. When finished, the SysTick
// peripheral is set back to its original state.
uint32_t t0, t1, top, ticks,
saveLoad = SysTick->LOAD, saveVal = SysTick->VAL;
#ifdef NEO_KHZ400 // 800 KHz check needed only if 400 KHz support enabled
if(is800KHz) {
#endif
top = (uint32_t)(F_CPU * 0.00000125); // Bit hi + lo = 1.25 uS
t0 = top - (uint32_t)(F_CPU * 0.00000040); // 0 = 0.4 uS hi
t1 = top - (uint32_t)(F_CPU * 0.00000080); // 1 = 0.8 uS hi
#ifdef NEO_KHZ400
} else { // 400 KHz bitstream
top = (uint32_t)(F_CPU * 0.00000250); // Bit hi + lo = 2.5 uS
t0 = top - (uint32_t)(F_CPU * 0.00000050); // 0 = 0.5 uS hi
t1 = top - (uint32_t)(F_CPU * 0.00000120); // 1 = 1.2 uS hi
}
#endif
SysTick->LOAD = top; // Config SysTick for NeoPixel bit freq
SysTick->VAL = top; // Set to start value (counts down)
(void)SysTick->VAL; // Dummy read helps sync up 1st bit
for(;;) {
*set = pinMask; // Set output high
ticks = (p & bitMask) ? t1 : t0; // SysTick threshold,
while(SysTick->VAL > ticks); // wait for it
*clr = pinMask; // Set output low
if(!(bitMask >>= 1)) { // Next bit for this byte...done?
if(ptr >= end) break; // If last byte sent, exit loop
p = *ptr++; // Fetch next byte
bitMask = 0x80; // Reset bitmask
}
while(SysTick->VAL <= ticks); // Wait for rollover to 'top'
}
SysTick->LOAD = saveLoad; // Restore SysTick rollover to 1 ms
SysTick->VAL = saveVal; // Restore SysTick value
#elif defined (ARDUINO_STM32_FEATHER) // FEATHER WICED (120MHz)
// Tried this with a timer/counter, couldn't quite get adequate
// resolution. So yay, you get a load of goofball NOPs...
uint8_t *ptr, *end, p, bitMask;
uint32_t pinMask;
pinMask = BIT(PIN_MAP[pin].gpio_bit);
ptr = pixels;
end = ptr + numBytes;
p = *ptr++;
bitMask = 0x80;
volatile uint16_t *set = &(PIN_MAP[pin].gpio_device->regs->BSRRL);
volatile uint16_t *clr = &(PIN_MAP[pin].gpio_device->regs->BSRRH);
#ifdef NEO_KHZ400 // 800 KHz check needed only if 400 KHz support enabled
if(is800KHz) {
#endif
for(;;) {
if(p & bitMask) { // ONE
// High 800ns
*set = pinMask;
asm("nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop;");
// Low 450ns
*clr = pinMask;
asm("nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop;");
} else { // ZERO
// High 400ns
*set = pinMask;
asm("nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop;");
// Low 850ns
*clr = pinMask;
asm("nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop; nop; nop; nop; nop;"
"nop; nop; nop; nop;");
}
if(bitMask >>= 1) {
// Move on to the next pixel
asm("nop;");
} else {
if(ptr >= end) break;
p = *ptr++;
bitMask = 0x80;
}
}
#ifdef NEO_KHZ400
} else { // 400 KHz bitstream
// ToDo!
}
#endif
#elif defined(TARGET_LPC1768)
uint8_t *ptr, *end, p, bitMask;
ptr = pixels;
end = ptr + numBytes;
p = *ptr++;
bitMask = 0x80;
#ifdef NEO_KHZ400 // 800 KHz check needed only if 400 KHz support enabled
if(is800KHz) {
#endif
for(;;) {
if(p & bitMask) {
// data ONE high
// min: 550 typ: 700 max: 5,500
gpio_set(pin);
time::delay_ns(550);
// min: 450 typ: 600 max: 5,000
gpio_clear(pin);
time::delay_ns(450);
} else {
// data ZERO high
// min: 200 typ: 350 max: 500
gpio_set(pin);
time::delay_ns(200);
// data low
// min: 450 typ: 600 max: 5,000
gpio_clear(pin);
time::delay_ns(450);
}
if(bitMask >>= 1) {
// Move on to the next pixel
asm("nop;");
} else {
if(ptr >= end) break;
p = *ptr++;
bitMask = 0x80;
}
}
#ifdef NEO_KHZ400
} else { // 400 KHz bitstream
// ToDo!
}
#endif
#elif defined(ARDUINO_ARCH_STM32)
uint8_t *p = pixels, *end = p + numBytes,
pix = *p++, mask = 0x80;
uint32_t cyc;
uint32_t saveLoad = SysTick->LOAD, saveVal = SysTick->VAL;
#ifdef NEO_KHZ400 // 800 KHz check needed only if 400 KHz support enabled
if(is800KHz) {
#endif
uint32_t top = (F_CPU / 800000); // 1.25µs
uint32_t t0 = top - (F_CPU / 2500000); // 0.4µs
uint32_t t1 = top - (F_CPU / 1250000); // 0.8µs
SysTick->LOAD = top - 1; // Config SysTick for NeoPixel bit freq
SysTick->VAL = 0; // Set to start value
for(;;) {
LL_GPIO_SetOutputPin(gpioPort, gpioPin);
cyc = (pix & mask) ? t1 : t0;
while(SysTick->VAL > cyc);
LL_GPIO_ResetOutputPin(gpioPort, gpioPin);
if(!(mask >>= 1)) {
if(p >= end) break;
pix = *p++;
mask = 0x80;
}
while(SysTick->VAL <= cyc);
}
#ifdef NEO_KHZ400
} else { // 400 kHz bitstream
uint32_t top = (F_CPU / 400000); // 2.5µs
uint32_t t0 = top - (F_CPU / 2000000); // 0.5µs
uint32_t t1 = top - (F_CPU / 833333); // 1.2µs
SysTick->LOAD = top - 1; // Config SysTick for NeoPixel bit freq
SysTick->VAL = 0; // Set to start value
for(;;) {
LL_GPIO_SetOutputPin(gpioPort, gpioPin);
cyc = (pix & mask) ? t1 : t0;
while(SysTick->VAL > cyc);
LL_GPIO_ResetOutputPin(gpioPort, gpioPin);
if(!(mask >>= 1)) {
if(p >= end) break;
pix = *p++;
mask = 0x80;
}
while(SysTick->VAL <= cyc);
}
}
#endif // NEO_KHZ400
SysTick->LOAD = saveLoad; // Restore SysTick rollover to 1 ms
SysTick->VAL = saveVal; // Restore SysTick value
#elif defined (NRF51)
uint8_t *p = pixels,
pix, count, mask;
int32_t num = numBytes;
unsigned int bitmask = ( 1 << g_ADigitalPinMap[pin] );
// https://github.com/sandeepmistry/arduino-nRF5/blob/dc53980c8bac27898fca90d8ecb268e11111edc1/variants/BBCmicrobit/variant.cpp
volatile unsigned int *reg = (unsigned int *) (0x50000000UL + 0x508);
// https://github.com/sandeepmistry/arduino-nRF5/blob/dc53980c8bac27898fca90d8ecb268e11111edc1/cores/nRF5/SDK/components/device/nrf51.h
// http://www.iot-programmer.com/index.php/books/27-micro-bit-iot-in-c/chapters-micro-bit-iot-in-c/47-micro-bit-iot-in-c-fast-memory-mapped-gpio?showall=1
// https://github.com/Microsoft/pxt-neopixel/blob/master/sendbuffer.asm
asm volatile(
// "cpsid i" ; disable irq
// b .start
"b L%=_start" "\n\t"
// .nextbit: ; C0
"L%=_nextbit:" "\n\t" //; C0
// str r1, [r3, #0] ; pin := hi C2
"strb %[bitmask], [%[reg], #0]" "\n\t" //; pin := hi C2
// tst r6, r0 ; C3
"tst %[mask], %[pix]" "\n\t"// ; C3
// bne .islate ; C4
"bne L%=_islate" "\n\t" //; C4
// str r1, [r2, #0] ; pin := lo C6
"strb %[bitmask], [%[reg], #4]" "\n\t" //; pin := lo C6
// .islate:
"L%=_islate:" "\n\t"
// lsrs r6, r6, #1 ; r6 >>= 1 C7
"lsr %[mask], %[mask], #1" "\n\t" //; r6 >>= 1 C7
// bne .justbit ; C8
"bne L%=_justbit" "\n\t" //; C8
// ; not just a bit - need new byte
// adds r4, #1 ; r4++ C9
"add %[p], #1" "\n\t" //; r4++ C9
// subs r5, #1 ; r5-- C10
"sub %[num], #1" "\n\t" //; r5-- C10
// bcc .stop ; if (r5<0) goto .stop C11
"bcc L%=_stop" "\n\t" //; if (r5<0) goto .stop C11
// .start:
"L%=_start:"
// movs r6, #0x80 ; reset mask C12
"movs %[mask], #0x80" "\n\t" //; reset mask C12
// nop ; C13
"nop" "\n\t" //; C13
// .common: ; C13
"L%=_common:" "\n\t" //; C13
// str r1, [r2, #0] ; pin := lo C15
"strb %[bitmask], [%[reg], #4]" "\n\t" //; pin := lo C15
// ; always re-load byte - it just fits with the cycles better this way
// ldrb r0, [r4, #0] ; r0 := *r4 C17
"ldrb %[pix], [%[p], #0]" "\n\t" //; r0 := *r4 C17
// b .nextbit ; C20
"b L%=_nextbit" "\n\t" //; C20
// .justbit: ; C10
"L%=_justbit:" "\n\t" //; C10
// ; no nops, branch taken is already 3 cycles
// b .common ; C13
"b L%=_common" "\n\t" //; C13
// .stop:
"L%=_stop:" "\n\t"
// str r1, [r2, #0] ; pin := lo
"strb %[bitmask], [%[reg], #4]" "\n\t" //; pin := lo
// cpsie i ; enable irq
: [p] "+r" (p),
[pix] "=&r" (pix),
[count] "=&r" (count),
[mask] "=&r" (mask),
[num] "+r" (num)
: [bitmask] "r" (bitmask),
[reg] "r" (reg)
);
#elif defined(__SAM3X8E__) // Arduino Due
#define SCALE VARIANT_MCK / 2UL / 1000000UL
#define INST (2UL * F_CPU / VARIANT_MCK)
#define TIME_800_0 ((int)(0.40 * SCALE + 0.5) - (5 * INST))
#define TIME_800_1 ((int)(0.80 * SCALE + 0.5) - (5 * INST))
#define PERIOD_800 ((int)(1.25 * SCALE + 0.5) - (5 * INST))
#define TIME_400_0 ((int)(0.50 * SCALE + 0.5) - (5 * INST))
#define TIME_400_1 ((int)(1.20 * SCALE + 0.5) - (5 * INST))
#define PERIOD_400 ((int)(2.50 * SCALE + 0.5) - (5 * INST))
int pinMask, time0, time1, period, t;
Pio *port;
volatile WoReg *portSet, *portClear, *timeValue, *timeReset;
uint8_t *p, *end, pix, mask;
pmc_set_writeprotect(false);
pmc_enable_periph_clk((uint32_t)TC3_IRQn);
TC_Configure(TC1, 0,
TC_CMR_WAVE | TC_CMR_WAVSEL_UP | TC_CMR_TCCLKS_TIMER_CLOCK1);
TC_Start(TC1, 0);
pinMask = g_APinDescription[pin].ulPin; // Don't 'optimize' these into
port = g_APinDescription[pin].pPort; // declarations above. Want to
portSet = &(port->PIO_SODR); // burn a few cycles after
portClear = &(port->PIO_CODR); // starting timer to minimize
timeValue = &(TC1->TC_CHANNEL[0].TC_CV); // the initial 'while'.
timeReset = &(TC1->TC_CHANNEL[0].TC_CCR);
p = pixels;
end = p + numBytes;
pix = *p++;
mask = 0x80;
#ifdef NEO_KHZ400 // 800 KHz check needed only if 400 KHz support enabled
if(is800KHz) {
#endif
time0 = TIME_800_0;
time1 = TIME_800_1;
period = PERIOD_800;
#ifdef NEO_KHZ400
} else { // 400 KHz bitstream
time0 = TIME_400_0;
time1 = TIME_400_1;
period = PERIOD_400;
}
#endif
for(t = time0;; t = time0) {
if(pix & mask) t = time1;
while(*timeValue < period);
*portSet = pinMask;
*timeReset = TC_CCR_CLKEN | TC_CCR_SWTRG;
while(*timeValue < t);
*portClear = pinMask;
if(!(mask >>= 1)) { // This 'inside-out' loop logic utilizes
if(p >= end) break; // idle time to minimize inter-byte delays.
pix = *p++;
mask = 0x80;
}
}
while(*timeValue < period); // Wait for last bit
TC_Stop(TC1, 0);
#endif // end Due
// END ARM ----------------------------------------------------------------
#elif defined(ESP8266) || defined(ESP32)
// ESP8266 ----------------------------------------------------------------
// ESP8266 show() is external to enforce ICACHE_RAM_ATTR execution
espShow(pin, pixels, numBytes, is800KHz);
#elif defined(__ARDUINO_ARC__)
// Arduino 101 -----------------------------------------------------------
#define NOPx7 { __builtin_arc_nop(); \
__builtin_arc_nop(); __builtin_arc_nop(); \
__builtin_arc_nop(); __builtin_arc_nop(); \
__builtin_arc_nop(); __builtin_arc_nop(); }
PinDescription *pindesc = &g_APinDescription[pin];
register uint32_t loop = 8 * numBytes; // one loop to handle all bytes and all bits
register uint8_t *p = pixels;
register uint32_t currByte = (uint32_t) (*p);
register uint32_t currBit = 0x80 & currByte;
register uint32_t bitCounter = 0;
register uint32_t first = 1;
// The loop is unusual. Very first iteration puts all the way LOW to the wire -
// constant LOW does not affect NEOPIXEL, so there is no visible effect displayed.
// During that very first iteration CPU caches instructions in the loop.
// Because of the caching process, "CPU slows down". NEOPIXEL pulse is very time sensitive
// that's why we let the CPU cache first and we start regular pulse from 2nd iteration
if (pindesc->ulGPIOType == SS_GPIO) {
register uint32_t reg = pindesc->ulGPIOBase + SS_GPIO_SWPORTA_DR;
uint32_t reg_val = __builtin_arc_lr((volatile uint32_t)reg);
register uint32_t reg_bit_high = reg_val | (1 << pindesc->ulGPIOId);
register uint32_t reg_bit_low = reg_val & ~(1 << pindesc->ulGPIOId);
loop += 1; // include first, special iteration
while(loop--) {
if(!first) {
currByte <<= 1;
bitCounter++;
}
// 1 is >550ns high and >450ns low; 0 is 200..500ns high and >450ns low
__builtin_arc_sr(first ? reg_bit_low : reg_bit_high, (volatile uint32_t)reg);
if(currBit) { // ~400ns HIGH (740ns overall)
NOPx7
NOPx7
}
// ~340ns HIGH
NOPx7
__builtin_arc_nop();
// 820ns LOW; per spec, max allowed low here is 5000ns */
__builtin_arc_sr(reg_bit_low, (volatile uint32_t)reg);
NOPx7
NOPx7
if(bitCounter >= 8) {
bitCounter = 0;
currByte = (uint32_t) (*++p);
}
currBit = 0x80 & currByte;
first = 0;
}
} else if(pindesc->ulGPIOType == SOC_GPIO) {
register uint32_t reg = pindesc->ulGPIOBase + SOC_GPIO_SWPORTA_DR;
uint32_t reg_val = MMIO_REG_VAL(reg);
register uint32_t reg_bit_high = reg_val | (1 << pindesc->ulGPIOId);
register uint32_t reg_bit_low = reg_val & ~(1 << pindesc->ulGPIOId);
loop += 1; // include first, special iteration
while(loop--) {
if(!first) {
currByte <<= 1;
bitCounter++;
}
MMIO_REG_VAL(reg) = first ? reg_bit_low : reg_bit_high;
if(currBit) { // ~430ns HIGH (740ns overall)
NOPx7
NOPx7
__builtin_arc_nop();
}
// ~310ns HIGH
NOPx7
// 850ns LOW; per spec, max allowed low here is 5000ns */
MMIO_REG_VAL(reg) = reg_bit_low;
NOPx7
NOPx7
if(bitCounter >= 8) {
bitCounter = 0;
currByte = (uint32_t) (*++p);
}
currBit = 0x80 & currByte;
first = 0;
}
}
#else
#error Architecture not supported
#endif
// END ARCHITECTURE SELECT ------------------------------------------------
#if !( defined(NRF52) || defined(NRF52_SERIES) )
interrupts();
#endif
endTime = micros(); // Save EOD time for latch on next call
}
/*!
@brief Set/change the NeoPixel output pin number. Previous pin,
if any, is set to INPUT and the new pin is set to OUTPUT.
@param p Arduino pin number (-1 = no pin).
*/
void Adafruit_CPlay_NeoPixel::setPin(uint16_t p) {
if(begun && (pin >= 0)) pinMode(pin, INPUT);
pin = p;
if(begun) {
pinMode(p, OUTPUT);
digitalWrite(p, LOW);
}
#ifdef __AVR__
port = portOutputRegister(digitalPinToPort(p));
pinMask = digitalPinToBitMask(p);
#endif
#ifdef ARDUINO_ARCH_STM32
gpioPort = digitalPinToPort(p);
gpioPin = STM_LL_GPIO_PIN(digitalPinToPinName(p));
#endif
}
/*!
@brief Set a pixel's color using separate red, green and blue
components. If using RGBW pixels, white will be set to 0.
@param n Pixel index, starting from 0.
@param r Red brightness, 0 = minimum (off), 255 = maximum.
@param g Green brightness, 0 = minimum (off), 255 = maximum.
@param b Blue brightness, 0 = minimum (off), 255 = maximum.
*/
void Adafruit_CPlay_NeoPixel::setPixelColor(
uint16_t n, uint8_t r, uint8_t g, uint8_t b) {
if(n < numLEDs) {
if(brightness) { // See notes in setBrightness()
r = (r * brightness) >> 8;
g = (g * brightness) >> 8;
b = (b * brightness) >> 8;
}
uint8_t *p;
if(wOffset == rOffset) { // Is an RGB-type strip
p = &pixels[n * 3]; // 3 bytes per pixel
} else { // Is a WRGB-type strip
p = &pixels[n * 4]; // 4 bytes per pixel
p[wOffset] = 0; // But only R,G,B passed -- set W to 0
}
p[rOffset] = r; // R,G,B always stored
p[gOffset] = g;
p[bOffset] = b;
}
}
/*!
@brief Set a pixel's color using separate red, green, blue and white
components (for RGBW NeoPixels only).
@param n Pixel index, starting from 0.
@param r Red brightness, 0 = minimum (off), 255 = maximum.
@param g Green brightness, 0 = minimum (off), 255 = maximum.
@param b Blue brightness, 0 = minimum (off), 255 = maximum.
@param w White brightness, 0 = minimum (off), 255 = maximum, ignored
if using RGB pixels.
*/
void Adafruit_CPlay_NeoPixel::setPixelColor(
uint16_t n, uint8_t r, uint8_t g, uint8_t b, uint8_t w) {
if(n < numLEDs) {
if(brightness) { // See notes in setBrightness()
r = (r * brightness) >> 8;
g = (g * brightness) >> 8;
b = (b * brightness) >> 8;
w = (w * brightness) >> 8;
}
uint8_t *p;
if(wOffset == rOffset) { // Is an RGB-type strip
p = &pixels[n * 3]; // 3 bytes per pixel (ignore W)
} else { // Is a WRGB-type strip
p = &pixels[n * 4]; // 4 bytes per pixel
p[wOffset] = w; // Store W
}
p[rOffset] = r; // Store R,G,B
p[gOffset] = g;
p[bOffset] = b;
}
}
/*!
@brief Set a pixel's color using a 32-bit 'packed' RGB or RGBW value.
@param n Pixel index, starting from 0.
@param c 32-bit color value. Most significant byte is white (for RGBW
pixels) or ignored (for RGB pixels), next is red, then green,
and least significant byte is blue.
*/
void Adafruit_CPlay_NeoPixel::setPixelColor(uint16_t n, uint32_t c) {
if(n < numLEDs) {
uint8_t *p,
r = (uint8_t)(c >> 16),
g = (uint8_t)(c >> 8),
b = (uint8_t)c;
if(brightness) { // See notes in setBrightness()
r = (r * brightness) >> 8;
g = (g * brightness) >> 8;
b = (b * brightness) >> 8;
}
if(wOffset == rOffset) {
p = &pixels[n * 3];
} else {
p = &pixels[n * 4];
uint8_t w = (uint8_t)(c >> 24);
p[wOffset] = brightness ? ((w * brightness) >> 8) : w;
}
p[rOffset] = r;
p[gOffset] = g;
p[bOffset] = b;
}
}
/*!
@brief Fill all or part of the NeoPixel strip with a color.
@param c 32-bit color value. Most significant byte is white (for
RGBW pixels) or ignored (for RGB pixels), next is red,
then green, and least significant byte is blue. If all
arguments are unspecified, this will be 0 (off).
@param first Index of first pixel to fill, starting from 0. Must be
in-bounds, no clipping is performed. 0 if unspecified.
@param count Number of pixels to fill, as a positive value. Passing
0 or leaving unspecified will fill to end of strip.
*/
void Adafruit_CPlay_NeoPixel::fill(uint32_t c, uint16_t first, uint16_t count) {
uint16_t i, end;
if(first >= numLEDs) {
return; // If first LED is past end of strip, nothing to do
}
// Calculate the index ONE AFTER the last pixel to fill
if(count == 0) {
// Fill to end of strip
end = numLEDs;
} else {
// Ensure that the loop won't go past the last pixel
end = first + count;
if(end > numLEDs) end = numLEDs;
}
for(i = first; i < end; i++) {
this->setPixelColor(i, c);
}
}
/*!
@brief Convert hue, saturation and value into a packed 32-bit RGB color
that can be passed to setPixelColor() or other RGB-compatible
functions.
@param hue An unsigned 16-bit value, 0 to 65535, representing one full
loop of the color wheel, which allows 16-bit hues to "roll
over" while still doing the expected thing (and allowing
more precision than the wheel() function that was common to
prior NeoPixel examples).
@param sat Saturation, 8-bit value, 0 (min or pure grayscale) to 255
(max or pure hue). Default of 255 if unspecified.
@param val Value (brightness), 8-bit value, 0 (min / black / off) to
255 (max or full brightness). Default of 255 if unspecified.
@return Packed 32-bit RGB with the most significant byte set to 0 -- the
white element of WRGB pixels is NOT utilized. Result is linearly
but not perceptually correct, so you may want to pass the result
through the gamma32() function (or your own gamma-correction
operation) else colors may appear washed out. This is not done
automatically by this function because coders may desire a more
refined gamma-correction function than the simplified
one-size-fits-all operation of gamma32(). Diffusing the LEDs also
really seems to help when using low-saturation colors.
*/
uint32_t Adafruit_CPlay_NeoPixel::ColorHSV(uint16_t hue, uint8_t sat, uint8_t val) {
uint8_t r, g, b;
// Remap 0-65535 to 0-1529. Pure red is CENTERED on the 64K rollover;
// 0 is not the start of pure red, but the midpoint...a few values above
// zero and a few below 65536 all yield pure red (similarly, 32768 is the
// midpoint, not start, of pure cyan). The 8-bit RGB hexcone (256 values
// each for red, green, blue) really only allows for 1530 distinct hues
// (not 1536, more on that below), but the full unsigned 16-bit type was
// chosen for hue so that one's code can easily handle a contiguous color
// wheel by allowing hue to roll over in either direction.
hue = (hue * 1530L + 32768) / 65536;
// Because red is centered on the rollover point (the +32768 above,
// essentially a fixed-point +0.5), the above actually yields 0 to 1530,
// where 0 and 1530 would yield the same thing. Rather than apply a
// costly modulo operator, 1530 is handled as a special case below.
// So you'd think that the color "hexcone" (the thing that ramps from
// pure red, to pure yellow, to pure green and so forth back to red,
// yielding six slices), and with each color component having 256
// possible values (0-255), might have 1536 possible items (6*256),
// but in reality there's 1530. This is because the last element in
// each 256-element slice is equal to the first element of the next
// slice, and keeping those in there this would create small
// discontinuities in the color wheel. So the last element of each
// slice is dropped...we regard only elements 0-254, with item 255
// being picked up as element 0 of the next slice. Like this:
// Red to not-quite-pure-yellow is: 255, 0, 0 to 255, 254, 0
// Pure yellow to not-quite-pure-green is: 255, 255, 0 to 1, 255, 0
// Pure green to not-quite-pure-cyan is: 0, 255, 0 to 0, 255, 254
// and so forth. Hence, 1530 distinct hues (0 to 1529), and hence why
// the constants below are not the multiples of 256 you might expect.
// Convert hue to R,G,B (nested ifs faster than divide+mod+switch):
if(hue < 510) { // Red to Green-1
b = 0;
if(hue < 255) { // Red to Yellow-1
r = 255;
g = hue; // g = 0 to 254
} else { // Yellow to Green-1
r = 510 - hue; // r = 255 to 1
g = 255;
}
} else if(hue < 1020) { // Green to Blue-1
r = 0;
if(hue < 765) { // Green to Cyan-1
g = 255;
b = hue - 510; // b = 0 to 254
} else { // Cyan to Blue-1
g = 1020 - hue; // g = 255 to 1
b = 255;
}
} else if(hue < 1530) { // Blue to Red-1
g = 0;
if(hue < 1275) { // Blue to Magenta-1
r = hue - 1020; // r = 0 to 254
b = 255;
} else { // Magenta to Red-1
r = 255;
b = 1530 - hue; // b = 255 to 1
}
} else { // Last 0.5 Red (quicker than % operator)
r = 255;
g = b = 0;
}
// Apply saturation and value to R,G,B, pack into 32-bit result:
uint32_t v1 = 1 + val; // 1 to 256; allows >>8 instead of /255
uint16_t s1 = 1 + sat; // 1 to 256; same reason
uint8_t s2 = 255 - sat; // 255 to 0
return ((((((r * s1) >> 8) + s2) * v1) & 0xff00) << 8) |
(((((g * s1) >> 8) + s2) * v1) & 0xff00) |
( ((((b * s1) >> 8) + s2) * v1) >> 8);
}
/*!
@brief Query the color of a previously-set pixel.
@param n Index of pixel to read (0 = first).
@return 'Packed' 32-bit RGB or WRGB value. Most significant byte is white
(for RGBW pixels) or 0 (for RGB pixels), next is red, then green,
and least significant byte is blue.
@note If the strip brightness has been changed from the default value
of 255, the color read from a pixel may not exactly match what
was previously written with one of the setPixelColor() functions.
This gets more pronounced at lower brightness levels.
*/
uint32_t Adafruit_CPlay_NeoPixel::getPixelColor(uint16_t n) const {
if(n >= numLEDs) return 0; // Out of bounds, return no color.
uint8_t *p;
if(wOffset == rOffset) { // Is RGB-type device
p = &pixels[n * 3];
if(brightness) {
// Stored color was decimated by setBrightness(). Returned value
// attempts to scale back to an approximation of the original 24-bit
// value used when setting the pixel color, but there will always be
// some error -- those bits are simply gone. Issue is most
// pronounced at low brightness levels.
return (((uint32_t)(p[rOffset] << 8) / brightness) << 16) |
(((uint32_t)(p[gOffset] << 8) / brightness) << 8) |
( (uint32_t)(p[bOffset] << 8) / brightness );
} else {
// No brightness adjustment has been made -- return 'raw' color
return ((uint32_t)p[rOffset] << 16) |
((uint32_t)p[gOffset] << 8) |
(uint32_t)p[bOffset];
}
} else { // Is RGBW-type device
p = &pixels[n * 4];
if(brightness) { // Return scaled color
return (((uint32_t)(p[wOffset] << 8) / brightness) << 24) |
(((uint32_t)(p[rOffset] << 8) / brightness) << 16) |
(((uint32_t)(p[gOffset] << 8) / brightness) << 8) |
( (uint32_t)(p[bOffset] << 8) / brightness );
} else { // Return raw color
return ((uint32_t)p[wOffset] << 24) |
((uint32_t)p[rOffset] << 16) |
((uint32_t)p[gOffset] << 8) |
(uint32_t)p[bOffset];
}
}
}
/*!
@brief Adjust output brightness. Does not immediately affect what's
currently displayed on the LEDs. The next call to show() will
refresh the LEDs at this level.
@param b Brightness setting, 0=minimum (off), 255=brightest.
@note This was intended for one-time use in one's setup() function,
not as an animation effect in itself. Because of the way this
library "pre-multiplies" LED colors in RAM, changing the
brightness is often a "lossy" operation -- what you write to
pixels isn't necessary the same as what you'll read back.
Repeated brightness changes using this function exacerbate the
problem. Smart programs therefore treat the strip as a
write-only resource, maintaining their own state to render each
frame of an animation, not relying on read-modify-write.
*/
void Adafruit_CPlay_NeoPixel::setBrightness(uint8_t b) {
// Stored brightness value is different than what's passed.
// This simplifies the actual scaling math later, allowing a fast
// 8x8-bit multiply and taking the MSB. 'brightness' is a uint8_t,
// adding 1 here may (intentionally) roll over...so 0 = max brightness
// (color values are interpreted literally; no scaling), 1 = min
// brightness (off), 255 = just below max brightness.
uint8_t newBrightness = b + 1;
if(newBrightness != brightness) { // Compare against prior value
// Brightness has changed -- re-scale existing data in RAM,
// This process is potentially "lossy," especially when increasing
// brightness. The tight timing in the WS2811/WS2812 code means there
// aren't enough free cycles to perform this scaling on the fly as data
// is issued. So we make a pass through the existing color data in RAM
// and scale it (subsequent graphics commands also work at this
// brightness level). If there's a significant step up in brightness,
// the limited number of steps (quantization) in the old data will be
// quite visible in the re-scaled version. For a non-destructive
// change, you'll need to re-render the full strip data. C'est la vie.
uint8_t c,
*ptr = pixels,
oldBrightness = brightness - 1; // De-wrap old brightness value
uint16_t scale;
if(oldBrightness == 0) scale = 0; // Avoid /0
else if(b == 255) scale = 65535 / oldBrightness;
else scale = (((uint16_t)newBrightness << 8) - 1) / oldBrightness;
for(uint16_t i=0; i<numBytes; i++) {
c = *ptr;
*ptr++ = (c * scale) >> 8;
}
brightness = newBrightness;
}
}
/*!
@brief Retrieve the last-set brightness value for the strip.
@return Brightness value: 0 = minimum (off), 255 = maximum.
*/
uint8_t Adafruit_CPlay_NeoPixel::getBrightness(void) const {
return brightness - 1;
}
/*!
@brief Fill the whole NeoPixel strip with 0 / black / off.
*/
void Adafruit_CPlay_NeoPixel::clear(void) {
memset(pixels, 0, numBytes);
}
// A 32-bit variant of gamma8() that applies the same function
// to all components of a packed RGB or WRGB value.
uint32_t Adafruit_CPlay_NeoPixel::gamma32(uint32_t x) {
uint8_t *y = (uint8_t *)&x;
// All four bytes of a 32-bit value are filtered even if RGB (not WRGB),
// to avoid a bunch of shifting and masking that would be necessary for
// properly handling different endianisms (and each byte is a fairly
// trivial operation, so it might not even be wasting cycles vs a check
// and branch for the RGB case). In theory this might cause trouble *if*
// someone's storing information in the unused most significant byte
// of an RGB value, but this seems exceedingly rare and if it's
// encountered in reality they can mask values going in or coming out.
for(uint8_t i=0; i<4; i++) y[i] = gamma8(y[i]);
return x; // Packed 32-bit return
}
|