| avrisp.name=AVR ISP |
| avrisp.communication=serial |
| avrisp.protocol=stk500v1 |
| avrisp.program.protocol=stk500v1 |
| avrisp.program.tool=avrdude |
| avrisp.program.extra_params=-P{serial.port} |
|
|
| avrispmkii.name=AVRISP mkII |
| avrispmkii.communication=usb |
| avrispmkii.protocol=stk500v2 |
| avrispmkii.program.protocol=stk500v2 |
| avrispmkii.program.tool=avrdude |
| avrispmkii.program.extra_params=-Pusb |
|
|
| usbtinyisp.name=USBtinyISP |
| usbtinyisp.protocol=usbtiny |
| usbtinyisp.program.tool=avrdude |
| usbtinyisp.program.extra_params= |
|
|
| arduinoisp.name=ArduinoISP |
| arduinoisp.protocol=arduinoisp |
| arduinoisp.program.tool=avrdude |
| arduinoisp.program.extra_params= |
|
|
| arduinoisporg.name=ArduinoISP.org |
| arduinoisporg.protocol=arduinoisporg |
| arduinoisporg.program.tool=avrdude |
| arduinoisporg.program.extra_params= |
|
|
| usbasp.name=USBasp |
| usbasp.communication=usb |
| usbasp.protocol=usbasp |
| usbasp.program.protocol=usbasp |
| usbasp.program.tool=avrdude |
| usbasp.program.extra_params=-Pusb |
|
|
| parallel.name=Parallel Programmer |
| parallel.protocol=dapa |
| parallel.force=true |
| # parallel.delay=200 |
| parallel.program.tool=avrdude |
| parallel.program.extra_params=-F |
|
|
| arduinoasisp.name=Arduino as ISP |
| arduinoasisp.communication=serial |
| arduinoasisp.protocol=stk500v1 |
| arduinoasisp.speed=19200 |
| arduinoasisp.program.protocol=stk500v1 |
| arduinoasisp.program.speed=19200 |
| arduinoasisp.program.tool=avrdude |
| arduinoasisp.program.extra_params=-P{serial.port} -b{program.speed} |
|
|
| arduinoasispatmega32u4.name=Arduino as ISP (ATmega32U4) |
| arduinoasispatmega32u4.communication=serial |
| arduinoasispatmega32u4.protocol=arduino |
| arduinoasispatmega32u4.speed=19200 |
| arduinoasispatmega32u4.program.protocol=arduino |
| arduinoasispatmega32u4.program.speed=19200 |
| arduinoasispatmega32u4.program.tool=avrdude |
| arduinoasispatmega32u4.program.extra_params=-P{serial.port} -b{program.speed} |
|
|
| usbGemma.name=Arduino Gemma |
| usbGemma.protocol=arduinogemma |
| usbGemma.program.tool=avrdude |
| usbGemma.program.extra_params= |
| usbGemma.config.path={runtime.platform.path}/bootloaders/gemma/avrdude.conf |
|
|
| ## Notes about Dangerous Prototypes Bus Pirate as ISP |
| ## Bus Pirate V3 need Firmware v5.10 or later |
| ## Bus Pirate V4 need Firmware v6.3-r2151 or later |
| ## Could happen that BP does not have enough current to power an Arduino board |
| ## through the ICSP connector. In this case disconnect the +Vcc from ICSP connector |
| ## and power Arduino board in the normal way. |
| buspirate.name=BusPirate as ISP |
| buspirate.communication=serial |
| buspirate.protocol=buspirate |
| buspirate.program.protocol=buspirate |
| buspirate.program.tool=avrdude |
| buspirate.program.extra_params=-P{serial.port} |
|
|
| # STK500 firmware version v1 and v2 use different serial protocols. |
| # Using the 'stk500' protocol tells avrdude to try and autodetect the |
| # firmware version. If this leads to problems, we might need to add |
| # stk500v1 and stk500v2 entries to allow explicitely selecting the |
| # firmware version. |
| stk500.name=Atmel STK500 development board |
| stk500.communication=serial |
| stk500.protocol=stk500 |
| stk500.program.protocol=stk500 |
| stk500.program.tool=avrdude |
| stk500.program.extra_params=-P{serial.port} |
|
|
| jtag3isp.name=Atmel JTAGICE3 (ISP mode) |
| jtag3isp.communication=usb |
| jtag3isp.protocol=jtag3isp |
| jtag3isp.program.protocol=jtag3isp |
| jtag3isp.program.tool=avrdude |
| jtag3isp.program.extra_params= |
|
|
| jtag3.name=Atmel JTAGICE3 (JTAG mode) |
| jtag3.communication=usb |
| jtag3.protocol=jtag3 |
| jtag3.program.protocol=jtag3 |
| jtag3.program.tool=avrdude |
| # Set a bitclock of 0.1us (the fastest supported value). This should |
| # work regardless of the crystal used, since JTAG doesn't use the MCU |
| # clock but dictates its own clock. |
| jtag3.program.extra_params=-B0.1 |
|
|
| atmel_ice.name=Atmel-ICE (AVR) |
| atmel_ice.communication=usb |
| atmel_ice.protocol=atmelice_isp |
| atmel_ice.program.protocol=atmelice_isp |
| atmel_ice.program.tool=avrdude |
| atmel_ice.program.extra_params=-Pusb |
|
|
