Replace with one-page circuit buckets list
Browse files
README.md
CHANGED
|
@@ -4,302 +4,42 @@ pretty_name: Copperhead circuit buckets
|
|
| 4 |
tags: [pcb, kicad, electronics]
|
| 5 |
---
|
| 6 |
|
| 7 |
-
#
|
| 8 |
-
|
| 9 |
-
|
| 10 |
-
|
| 11 |
-
**
|
| 12 |
-
|
| 13 |
-
|
| 14 |
-
|
| 15 |
-
|
| 16 |
-
|
| 17 |
-
--
|
| 18 |
-
|
| 19 |
-
|
| 20 |
-
|
| 21 |
-
- **
|
| 22 |
-
- **
|
| 23 |
-
- **
|
| 24 |
-
|
| 25 |
-
|
| 26 |
-
|
| 27 |
-
|
| 28 |
-
|
| 29 |
-
|
| 30 |
-
- **
|
| 31 |
-
- **
|
| 32 |
-
|
| 33 |
-
|
| 34 |
-
|
| 35 |
-
|
| 36 |
-
|
| 37 |
-
|
| 38 |
-
-
|
| 39 |
-
-
|
| 40 |
-
|
| 41 |
-
|
| 42 |
-
-
|
| 43 |
-
|
| 44 |
-
|
| 45 |
-
|
| 46 |
-
**Fit today: Good (module-based); Partial (wearables, chip-down radio).**
|
| 47 |
-
|
| 48 |
-
- **Typical boards:** soil or environmental sensor with ESP32 or nRF52, data logger, Bluetooth Low Energy (BLE) beacon, LoRa tracker, smart ring or glasses electronics.
|
| 49 |
-
- **Electrical success factors:** a microamp-level sleep current budget; regulator quiescent current; sensor placement away from heat; antenna keep-out. Espressif recommends a 4-layer board with a complete ground plane under the chip, RF path and crystal, and keeping copper and components away from the antenna [48].
|
| 50 |
-
- **Process factors:** using a module with its own radio certification lets the host product skip a new intentional-radiator certification under FCC (US Federal Communications Commission) rules, if the module grant's integration conditions are followed; the host still needs unintentional-emissions testing [49]. A simple FCC Part 15B test program is quoted at roughly $1,500 to $3,500 at one accredited lab [44].
|
| 51 |
-
- **Machine-verifiable:** ERC/DRC, power-budget arithmetic, firmware behaviour in simulation. Antenna performance can be estimated with full-wave simulation (Fang has shown an openEMS antenna run [12]) but must be confirmed in a chamber.
|
| 52 |
-
- **Copperhead fit:** Good for module-based nodes. Its STM32 logger has itemised power budgets but shipped draft power tracks below its own targets and 90 silkscreen DRC findings, and was never fabricated [16]. The Kyra smart-glasses and ring run reached part selection only [21]. A GNSS (satellite positioning) plus LoRa tracker is a "hard" example brief [5].
|
| 53 |
-
|
| 54 |
-
### 2.3 Low-voltage power conversion (buck, boost, LDO, USB Power Delivery, PoE)
|
| 55 |
-
|
| 56 |
-
**Fit today: Good (simple regulators); Partial (USB-PD supplies, PoE).**
|
| 57 |
-
|
| 58 |
-
- **Typical boards:** 12 V or battery to 5 V/3.3 V buck modules, boost converters, linear regulator (LDO) rails, USB Power Delivery (USB-PD) bench supplies, Power over Ethernet (PoE) powered devices.
|
| 59 |
-
- **Electrical success factors:** the high-current switching loop. TI calls the input capacitor "the single-most important component for reliable operation of any step-down converter" and says to place it as close to the IC as manufacturing rules allow [46]. Also: small switch-node copper, inductor and output-capacitor ratings, loop stability, thermal pads with vias, trace width per IPC-2152 [28]. PoE adds an isolation barrier: IEEE 802.3 requires the powered device to withstand 1500 V RMS for 60 s (or 2250 V DC, or an impulse test) [47].
|
| 60 |
-
- **Process factors:** 1 oz versus 2 oz copper changes the minimum track and space a fab can hold [37]; thermal verification on the bench; conducted and radiated EMC testing, where switching converters are a common failure source [45].
|
| 61 |
-
- **Machine-verifiable:** operating point, ripple and transient response in SPICE; datasheet limits; copper temperature rise with a thermal model; trace width versus current against IPC-2152 curves [29]. DRC can enforce net-class widths once they are written.
|
| 62 |
-
- **Needs judgment or test:** switching-loop layout, EMC, real thermal.
|
| 63 |
-
- **Copperhead fit:** Good for single regulators: Fang has shown an MC34063 buck/boost checked against its datasheet reference design with ngspice and thermal runs [11]. Partial above that: the 100 W USB-PD supply is a "hard" example brief with no published run [5], and nothing shows Copperhead writing an isolation net class for PoE.
|
| 64 |
-
|
| 65 |
-
### 2.4 Battery management and charging
|
| 66 |
-
|
| 67 |
-
**Fit today: Good (single-cell chargers); Partial (multi-cell low-voltage BMS); Poor (high-voltage packs).**
|
| 68 |
-
|
| 69 |
-
- **Typical boards:** single-cell Li-ion charger with fuel gauge; 4S to 16S battery management system (BMS) with an analog front end (AFE), protection MOSFETs and balancing; energy-storage BMS.
|
| 70 |
-
- **Electrical success factors:** Kelvin (4-wire) sensing at the shunt and cell taps, with low-current ground separated from the high-current path and joined only at the sense resistor [54]; cell-input RC filters placed close to the monitor IC [54]; FET-bank current capacity and thermal path; short-circuit response time; spacing across stacked cell voltages.
|
| 71 |
-
- **Process factors:** heavy copper or busbars for high current; pack-level safety standards such as IEC 62619 or UL 2580 [UNVERIFIED]; functional test with a cell simulator; abuse tests at pack level.
|
| 72 |
-
- **Machine-verifiable:** schematic correctness against the AFE datasheet, protection thresholds, thermal estimates, short-circuit timing in SPICE. Spacing rules are checkable only once voltage classes are mapped to net classes.
|
| 73 |
-
- **Copperhead fit:** the repo's own 4S LiFePO4 BMS example (100 A peak, isolated CAN, 1 kV functional isolation) is rated "hard" and described as "safety-critical, high current, thermal and isolation constraints" [5][6]. A single-cell charger (BQ24075) appears in the STM32 logger [16]. High-voltage vehicle packs need functional safety work (section 2.12) and are out of reach.
|
| 74 |
-
|
| 75 |
-
### 2.5 Motor drives and robotics electronics
|
| 76 |
-
|
| 77 |
-
**Fit today: Good (low-current drivers, sensor and CAN nodes); Partial (24-48 V servo drives); Poor (high-current ESCs and traction drives).**
|
| 78 |
-
|
| 79 |
-
- **Typical boards:** brushed-DC and stepper drivers, small three-phase brushless (BLDC) servo drives, encoder interfaces, robot joint controllers on CAN bus, electronic speed controllers (ESCs).
|
| 80 |
-
- **Electrical success factors:** TI's motor-driver layout guide stresses a short, wide supply-to-MOSFET-to-motor loop with few layer changes, multiple vias for high current, direct-connected thermal vias under the driver pad, and an unbroken ground plane [53]; gate-loop inductance; shunt placement; dead time; regenerative energy handling.
|
| 81 |
-
- **Process factors:** 2 oz or heavier copper for phase currents; thermal interface to a heatsink or housing; drive safety standard IEC 61800-5-1 for industrial drives [31]; EMC.
|
| 82 |
-
- **Machine-verifiable:** gate-drive transients and dead time in SPICE; thermal estimates; firmware pin maps; interface typing (Fang has typed CAN, PWM, encoder and motor-phase interfaces [8]).
|
| 83 |
-
- **Needs judgment or test:** power-stage layout, switching EMI, thermal under load.
|
| 84 |
-
- **Copperhead fit:** robotics is the vertical with the most public signal: the founder wrote "we are building claude code for robot electronics" [69], the Fang `servo_drive` example (three half-bridges, 24 V, 15 A per phase, CAN) is "the board this toolchain was written for" but is netlist only with no layout [9], and a dual brushed-DC driver is a "medium" brief [7]. Fang also showed a gate driver switching a 600 V-class MOSFET at 400 V and 10 A in ngspice, where moving one 0.1 µF capacitor changed the result [10]. High-current ESCs depend on exactly the routing Copperhead leaves to humans [2].
|
| 85 |
-
|
| 86 |
-
### 2.6 Industrial I/O and automation
|
| 87 |
-
|
| 88 |
-
**Fit today: Partial.**
|
| 89 |
-
|
| 90 |
-
- **Typical boards:** programmable logic controller (PLC) digital input and output modules, 4-20 mA current-loop analog inputs, RS-485/Modbus nodes, fieldbus and industrial Ethernet interfaces, isolated sensor interfaces.
|
| 91 |
-
- **Electrical success factors:** standard input behaviour (IEC 61131-2 defines 24 V digital input Types 1, 2 and 3 by switching voltage and current thresholds [55]); galvanic isolation of signal and power where grounds differ [56]; RS-485 bus termination at the two cable ends only, typically 120 Ω, with short stubs [56]; surge, burst and ESD protection at every field port; isolated receivers such as TI's ISO1212 [67] and 4-20 mA reference designs such as TIDA-00548 [68]; functional safety per IEC 61508, which grades safety functions SIL 1 to 4 and uses FMEDA to quantify diagnostic coverage [61], for safety I/O.
|
| 92 |
-
- **Process factors:** industrial temperature range parts; conformal coating for harsh sites, which also changes the IPC-2221 spacing category [30][41]; long product life, so BOM lifecycle risk matters [43]; EMC immunity testing per port. One lab quotes IEC 61326-1 industrial CE marking at $7,000 to $14,000 and notes each added port adds immunity injection time [44].
|
| 93 |
-
- **Machine-verifiable:** schematic against reference designs; thresholds and loop burden in SPICE; isolation spacing via KiCad creepage and clearance rules once net classes exist [24][25].
|
| 94 |
-
- **Needs judgment or test:** surge survival, isolation-barrier layout.
|
| 95 |
-
- **Copperhead fit:** Partial. Fang types RS-485 and CAN interfaces [8], and these reference-design-driven circuits suit spec-to-schematic work. But isolation barriers need creepage rules that Copperhead does not generate [3], and no industrial example board exists in its public record. Industrial work appears only as a hiring "nice-to-have" [15].
|
| 96 |
-
|
| 97 |
-
### 2.7 SBC/SoM carrier boards and high-speed digital
|
| 98 |
-
|
| 99 |
-
**Fit today: Partial (carrier schematic and parts); Poor (high-speed layout, chip-down DDR or PCIe).**
|
| 100 |
-
|
| 101 |
-
- **Typical boards:** Raspberry Pi Compute Module 5 (CM5) or NVIDIA Jetson carriers with PCIe, USB 3, Ethernet and camera links; chip-down processor boards with DDR memory.
|
| 102 |
-
- **Electrical success factors:** controlled impedance and length matching. The CM5 datasheet says PCIe, USB 3.0 and USB 2.0 pairs should be routed as 90 Ω differential pairs with length matching within each pair [51]; TI's high-speed guide says to route high-speed signals over a solid ground reference and not across plane splits or voids [50]; PCIe add-in-card interconnects target 85 Ω per a TI layout note [66]. A stackup agreed with the fab sets trace widths; via count and stubs matter.
|
| 103 |
-
- **Process factors:** 6 to 8+ layers; controlled-impedance fabrication (JLCPCB offers it from 4 layers with ±10% tolerance [37]; its free impedance test is ±20%, precision testing is charged [38]); boundary scan (IEEE 1149.1/JTAG) to test nets hidden under ball-grid-array (BGA) parts, which finds opens and shorts but does not prove signal integrity [40]; X-ray inspection of BGAs.
|
| 104 |
-
- **Machine-verifiable:** KiCad custom rules can check differential-pair gap, length and skew [26]; impedance follows from stackup geometry. Full signal-integrity simulation with IBIS models is outside anything Copperhead or Fang has shown [UNVERIFIED].
|
| 105 |
-
- **Needs judgment or test:** stackup, power integrity, eye diagrams, bring-up.
|
| 106 |
-
- **Copperhead fit:** Partial for carriers via its services motion: a forward-deployed engineer role owns "a live Raspberry Pi CM5 carrier-board project" and requires prior CM4/CM5 carrier experience, which implies a senior human does the layout [14]. Default rules assume no controlled impedance [4]. Chip-down DDR or PCIe is out of reach.
|
| 107 |
-
|
| 108 |
-
### 2.8 RF and wireless (chip-down)
|
| 109 |
-
|
| 110 |
-
**Fit today: Poor (chip-down); see 2.2 for module-based designs.**
|
| 111 |
-
|
| 112 |
-
- **Typical boards:** transceivers with discrete matching networks, multi-antenna cellular boards, 5.8 GHz video transmitters.
|
| 113 |
-
- **Electrical success factors:** 50 Ω controlled-impedance feed lines over a continuous ground, ground-via stitching, matching networks tuned on the real board, antenna keep-out and coexistence between radios [48].
|
| 114 |
-
- **Process factors:** RF laminates where FR-4 losses are too high (JLCPCB offers 2-layer Rogers/PTFE boards [37]); network-analyzer tuning; intentional-radiator certification for any non-modular radio [49]; a first-time EMC failure rate around 50% has been reported by a test lab [45].
|
| 115 |
-
- **Machine-verifiable:** impedance from stackup; antenna patterns with full-wave simulation (openEMS); DRC keep-outs as rules.
|
| 116 |
-
- **Copperhead fit:** Poor for chip-down work. Fang showed an openEMS run on an ESP32-C3 antenna [12], but default rules have no controlled impedance [4] and briefs with two RF chains are rated "hard" [5].
|
| 117 |
-
|
| 118 |
-
### 2.9 Precision analog, instrumentation and audio
|
| 119 |
-
|
| 120 |
-
**Fit today: Partial.**
|
| 121 |
-
|
| 122 |
-
- **Typical boards:** sensor conditioning, precision ADC front ends, instruments, audio amplifiers.
|
| 123 |
-
- **Electrical success factors:** grounding and return paths. Analog Devices' MT-031 tutorial recommends a large low-impedance ground plane and, for most mixed-signal designs, one common ground plane rather than split analog and digital planes [52]; local low-inductance decoupling; guarding of high-impedance nodes; component tolerance and drift budgets; thermal gradients near references. Instrument safety for mains-connected equipment follows IEC 61010-1, which sets creepage by working voltage, pollution degree and material group [33].
|
| 124 |
-
- **Process factors:** board cleanliness before coating [41]; calibration in functional test [39].
|
| 125 |
-
- **Machine-verifiable:** this bucket has the richest simulation story. Gain, bandwidth, noise and stability are SPICE-checkable claims; the Fang repository includes a set of op-amp handbook example circuits with simulated claims [8].
|
| 126 |
-
- **Needs judgment or test:** layout-induced noise, real accuracy.
|
| 127 |
-
- **Copperhead fit:** Partial. Circuit-level correctness is well suited to SPICE-checked generation, but the outcome hinges on layout, which is human. A PDM microphone board appears as a benchmark fixture [18].
|
| 128 |
-
|
| 129 |
-
### 2.10 LED and lighting
|
| 130 |
-
|
| 131 |
-
**Fit today: Good (low-voltage LED boards); Poor (mains LED drivers).**
|
| 132 |
-
|
| 133 |
-
- **Typical boards:** PWM LED boards, DMX stage-lighting interfaces, constant-current drivers, mains bulb drivers.
|
| 134 |
-
- **Electrical success factors:** thermal design first. TI notes that a metal-core PCB with an exposed pad and thermal vias gives roughly 10 °C/W for a PowerPAD driver versus about 70 °C/W for a SOIC-8 package in its example [57]; constant-current accuracy; flicker; for mains drivers, creepage and clearance and line-surge immunity [31].
|
| 135 |
-
- **Process factors:** metal-core (aluminium) boards, which JLCPCB offers as 1-layer [37]; lighting EMC standards (CISPR 15, EN 61547 and harmonics limits) [44]; safety certification for mains products.
|
| 136 |
-
- **Machine-verifiable:** current and thermal estimates; PWM firmware; IPC-2221 spacing tables are deterministic once voltage classes are known [30].
|
| 137 |
-
- **Copperhead fit:** Good for low-voltage boards: the Quiet Orbit LED board is ERC/DRC clean (unbuilt) [23] and an rp2040 DMX board is a benchmark fixture [18]. Mains drivers are Poor: the only mains example is a teardown analysis, not a design [22], and there are no creepage rules [3].
|
| 138 |
-
|
| 139 |
-
### 2.11 Drone and aerospace avionics
|
| 140 |
-
|
| 141 |
-
**Fit today: Good to Partial (flight controllers, GPS, BEC); Poor (4-in-1 ESCs, video transmitters); out of reach (certified airborne hardware).**
|
| 142 |
-
|
| 143 |
-
- **Typical boards:** flight controllers, GPS and compass modules, battery-eliminator-circuit (BEC) regulators, power distribution boards, ESCs.
|
| 144 |
-
- **Electrical success factors:** inertial-measurement-unit (IMU) noise. Betaflight's manufacturer guidelines require a dedicated LDO for the ICM-42688-P gyro, target supply noise under 50 µV peak-to-peak, require the gyro on its own SPI bus, and constrain motor-output timers and DMA [63]. PX4 also covers IMU placement and vibration isolation [64]. Power boards and ESCs are high-current, heavy-copper designs (see 2.5).
|
| 145 |
-
- **Process factors:** Betaflight review of schematics, layouts and production samples before a board is marked "Betaflight Supported" [63]; flight testing with blackbox logs. Crewed aircraft electronics follow RTCA DO-254 design assurance, with levels A to E scaled by failure severity, recognised by the FAA in AC 20-152A [62].
|
| 146 |
-
- **Machine-verifiable:** many Betaflight rules are checkable from the netlist (gyro on dedicated SPI bus, motor pins on one GPIO port, LDO present, specified LED and debug pins) [63]. This is an unusually crisp, public rule set for a checker.
|
| 147 |
-
- **Needs judgment or test:** vibration, ESC and video EMI, flight behaviour.
|
| 148 |
-
- **Copperhead fit:** drones are not a stated target; the only public signals are a hiring "nice-to-have" and a reply guessing at someone else's drone boards [15][70]. Technically, flight controllers resemble the STM32 logger (MCU, SPI sensors, flash) [16], so fit is Good to Partial, capped by dense 4-6 layer layout. ESCs are Poor for the reasons in 2.5. DO-254 work is out of reach.
|
| 149 |
-
|
| 150 |
-
### 2.12 Automotive and electric-vehicle electronics
|
| 151 |
-
|
| 152 |
-
**Fit today: Partial (prototypes of low-voltage controllers and CAN nodes); Poor (production, high-voltage).**
|
| 153 |
-
|
| 154 |
-
- **Typical boards:** CAN nodes, vehicle control units, body controllers, telematics, 12 V/48 V auxiliary converters; high-voltage BMS, inverters, on-board chargers.
|
| 155 |
-
- **Electrical success factors:** 12 V supply robustness against cold crank, load dump and reverse polarity, with load dump now covered by ISO 16750-2 [59]; components qualified to AEC-Q100 (ICs) and AEC-Q200 (passives) [58]; vehicle EMC (CISPR 25) [59]; wide temperature range.
|
| 156 |
-
- **Process factors:** functional safety under ISO 26262, whose Part 5 covers hardware development [60]; supplier quality processes; IPC Class 3 is common in safety-related uses [36]; one EMC test write-up says automotive requirements are significantly more stringent than consumer and medical ones [45].
|
| 157 |
-
- **Machine-verifiable:** part qualification lookup (is every part AEC-Q rated?); transient protection in SPICE; CAN termination and topology; creepage for high-voltage nets via KiCad rules [24].
|
| 158 |
-
- **Needs judgment or test:** safety analysis such as failure modes, effects and diagnostic analysis (FMEDA), validation, EMC.
|
| 159 |
-
- **Copperhead fit:** Partial for prototypes: CAN nodes and controllers are reference-design-driven and Fang types CAN [8]. No AEC-Q filtering or ISO 26262 work products are documented [UNVERIFIED: based on keyword search of public repos]. High-voltage EV boards are out of reach (see 2.14). EVs are not a stated target.
|
| 160 |
-
|
| 161 |
-
### 2.13 Medical devices
|
| 162 |
-
|
| 163 |
-
**Fit today: Poor (production); Partial (non-patient-connected prototypes).**
|
| 164 |
-
|
| 165 |
-
- **Typical boards:** patient monitors, diagnostic and infusion equipment.
|
| 166 |
-
- **Electrical success factors:** IEC 60601-1 means of protection. At a 250 V AC working voltage, two means of patient protection (2×MOPP) require 4,000 V AC isolation, 8 mm creepage and 5 mm clearance [34]; leakage-current limits; essential-performance under EMC per IEC 60601-1-2 [44].
|
| 167 |
-
- **Process factors:** a quality management system and documented design controls (regulatory process, out of scope for a PCB tool); EMC programs quoted at $8,000 to $18,000 at one lab [44]; a test lab has reported that over 90% of electrical medical devices it tested failed the required standards on first submission [45].
|
| 168 |
-
- **Machine-verifiable:** creepage and clearance once barriers are defined; leakage estimates.
|
| 169 |
-
- **Copperhead fit:** Poor for production. Its pricing page offers an Enterprise "audit trail your compliance team can hand over" [71], but no medical feature, creepage rule generation or design-control workflow is public. Medical is a hiring "nice-to-have" only [15].
|
| 170 |
-
|
| 171 |
-
### 2.14 High-voltage and mains power
|
| 172 |
-
|
| 173 |
-
**Fit today: Poor.**
|
| 174 |
-
|
| 175 |
-
- **Typical boards:** offline switch-mode power supplies (SMPS), power-factor correction (PFC) stages, solar and motor inverters, EV on-board chargers and traction inverters, EV charging-station controllers.
|
| 176 |
-
- **Electrical success factors:** insulation coordination. Creepage depends on working voltage, pollution degree and material group under IEC 60664-1, IEC 62368-1 (audio/video and IT equipment) or IEC 61010-1 [31][33]; one IEC 62368-1 calculator gives 2.5 mm basic creepage at 250 V RMS, pollution degree 2, material group IIIa, doubled for reinforced insulation [32]. IPC-2221 bare-board spacing for uncoated external conductors at 301-500 V is 2.5 mm below 3,050 m altitude [30].
|
| 177 |
-
- **Process factors:** safety-agency certification; production hipot (dielectric withstand) testing; heavy copper [65].
|
| 178 |
-
- **Machine-verifiable:** spacing rules (KiCad 9 creepage DRC [24][25]); switching waveforms in SPICE; thermal estimates.
|
| 179 |
-
- **Needs judgment or test:** magnetics, power-loop layout, certification.
|
| 180 |
-
- **Copperhead fit:** Poor. The default 0.2 mm single-class rule [3] is below the IPC-2221 uncoated external spacing for anything above 30 V [30], and Copperhead does not generate creepage rules [3]. Fang's 400 V/10 A gate-driver simulation [10] shows interest, not a design capability.
|
| 181 |
-
|
| 182 |
-
|
| 183 |
-
## 3. Summary table
|
| 184 |
-
|
| 185 |
-
"Checkable" means the main success factors can be scored by an automated checker (ERC/DRC with appropriate rules, datasheet lookup, SPICE or thermal simulation) without a lab. All fit ratings are this document's assessment.
|
| 186 |
-
|
| 187 |
-
| Bucket | Example | Key success factors | Checkable? | Copperhead fit |
|
| 188 |
-
|---|---|---|---|---|
|
| 189 |
-
| 2.1 MCU control and dev boards | RP2040 or STM32 board with USB-C | Power tree, decoupling, USB pair, boot pins | Mostly yes | Good |
|
| 190 |
-
| 2.2 Sensor, IoT, wearable nodes | ESP32 soil sensor, BLE beacon | Sleep current, antenna keep-out, certified module | Mostly yes; radio range needs test | Good (module); Partial (wearable) |
|
| 191 |
-
| 2.3 Low-voltage power | 12 V to 5 V buck, USB-PD supply | Switching loop, IPC-2152 widths, thermal, EMC | Partly (SPICE, thermal, widths) | Good (simple); Partial |
|
| 192 |
-
| 2.4 Battery management | 1S charger; 4S-16S BMS | Kelvin sensing, FET current path, protection timing | Partly | Good (1S); Partial (multi-cell) |
|
| 193 |
-
| 2.5 Motor drives, robotics | Brushed-DC driver, 24 V servo drive | Power loop, gate loop, thermal, shunts | Partly (SPICE, thermal) | Good (low current); Partial; Poor (ESC) |
|
| 194 |
-
| 2.6 Industrial I/O | 24 V PLC inputs, RS-485, 4-20 mA | IEC 61131-2 behaviour, isolation, surge, lifecycle | Partly (rules once written) | Partial |
|
| 195 |
-
| 2.7 Carriers and high-speed | CM5 carrier; chip-down DDR | Impedance, length match, stackup, return paths | Geometry yes; signal integrity no | Partial (carrier); Poor (high-speed) |
|
| 196 |
-
| 2.8 RF chip-down | Sub-GHz radio with matching | 50 Ω lines, matching, keep-outs, certification | Weakly (EM sim estimates) | Poor |
|
| 197 |
-
| 2.9 Precision analog, audio | ADC front end, microphone board | Grounding, noise, drift, guarding | Circuit yes; layout no | Partial |
|
| 198 |
-
| 2.10 LED and lighting | PWM LED board; mains bulb driver | Thermal path, current accuracy, mains spacing | Partly | Good (LV); Poor (mains) |
|
| 199 |
-
| 2.11 Drone avionics | Flight controller, GPS, ESC | IMU power and bus rules, vibration, high current | Netlist rules yes; flight no | Good-Partial (FC); Poor (ESC) |
|
| 200 |
-
| 2.12 Automotive, EV | CAN node; VCU; HV BMS | AEC-Q parts, transients, CISPR 25, ISO 26262 | Parts lookup yes; safety no | Partial (prototype); Poor (production) |
|
| 201 |
-
| 2.13 Medical | Patient monitor | 2×MOPP isolation, leakage, IEC 60601-1-2 | Spacing yes; process no | Poor |
|
| 202 |
-
| 2.14 High-voltage, mains | Offline SMPS, inverter, OBC | Creepage, magnetics, power loops, certification | Spacing yes; rest no | Poor |
|
| 203 |
-
|
| 204 |
-
## 4. Cross-cutting success factors and implications
|
| 205 |
-
|
| 206 |
-
**What industry does on every bucket.**
|
| 207 |
-
- **Design reviews against datasheets and reference designs.** Betaflight's first review step is to check schematics and layouts against the application notes of each datasheet [63]. Copperhead's v0.12 `review` command covers track widths against current, differential pairs, length matching and clearances [17].
|
| 208 |
-
- **DFM with the fab house.** Stackup, impedance, minimum track and space and copper weight are set by the fab's process, not by the designer alone [37][38]. Fabs and assemblers expect panel rails, fiducials and tooling holes [42].
|
| 209 |
-
- **BOM availability and lifecycle.** Obsolescence is managed as a BOM-level risk; not-recommended-for-new-design parts should be avoided in new boards [43].
|
| 210 |
-
- **Test coverage.** Flying probe for prototypes, bed-of-nails in-circuit test (ICT) for stable volume, and functional test as the final powered gate [39]; boundary scan where BGAs block probe access [40].
|
| 211 |
-
- **Certification.** EMC and safety testing is a gate in most buckets; about half of devices reportedly fail EMC on the first try [45], and planning ranges run from about $1,500 for a simple FCC test to $8,000-$18,000 for medical EMC at one lab [44].
|
| 212 |
-
|
| 213 |
-
**Implications for Copperhead (assessment).**
|
| 214 |
-
- Its strongest buckets (2.1, 2.2, simple 2.3 and 2.10) are those where the hard parts are schematic correctness and part choice, which it automates, and where layout risk is low.
|
| 215 |
-
- The single largest gap across 2.4, 2.5, 2.6, 2.12, 2.13 and 2.14 is that it does not translate voltage and current requirements into net classes: creepage and clearance by voltage class [24][31] and IPC-2152 widths by current [28]. KiCad already provides the checker; Copperhead would need to write the rules. This would move several Partial ratings up without solving routing.
|
| 216 |
-
- Controlled impedance (2.7, 2.8) is also mostly rule-writing against a published fab stackup [37][38].
|
| 217 |
-
- Production gates (Class 3, AEC-Q, ISO 26262, IEC 60601) are process and documentation work that no PCB tool replaces.
|
| 218 |
-
|
| 219 |
-
**Implications for training data and verifiable environments (assessment).**
|
| 220 |
-
- **Cleanest checkable rewards:** ERC/DRC pass with no collateral edits on real boards; pin-map and footprint grounding against KiCad libraries; datasheet-limit checks [19]; netlist-level rule sets such as Betaflight's flight-controller rules [63]; IPC-2221 spacing and IPC-2152 width lookups [29][30]; SPICE claims for analog and power circuits [8]. These map to buckets 2.1, 2.2, 2.3, 2.9, 2.11 (flight controllers) and the schematic side of 2.6.
|
| 221 |
-
- **Partly checkable:** isolation and creepage (rules are deterministic once voltage classes are labelled correctly, but the labelling is a judgment); impedance geometry; thermal estimates.
|
| 222 |
-
- **Hard to reward automatically:** EMC outcomes, RF performance, signal integrity on real hardware, vibration, and certification results. These need lab data. Copperbench, the company's benchmark, explicitly does not claim fabrication readiness or design quality [18].
|
| 223 |
-
|
| 224 |
-
## 5. Sources
|
| 225 |
-
|
| 226 |
-
All sources were public web pages accessed 2026-10-19 to 2026-10-21. Standards are cited through publicly readable summaries where the standard itself is paywalled.
|
| 227 |
-
|
| 228 |
-
**Copperhead and Fang**
|
| 229 |
-
1. Copperhead README: https://github.com/copperheadhq/copperhead/blob/main/README.md
|
| 230 |
-
2. `create` stage prompts (stage 5 layout: route power and short critical nets): https://github.com/copperheadhq/copperhead/blob/main/src/commands/create.ts
|
| 231 |
-
3. Scaffolded design rules (single default net class, 0.2 mm clearance): https://github.com/copperheadhq/copperhead/blob/main/src/kicad/bootstrap.ts
|
| 232 |
-
4. Docs, design from a brief: https://docs.copperhead.sh/workflows/create-from-brief/
|
| 233 |
-
5. Example briefs and difficulty tiers: https://github.com/copperheadhq/copperhead/blob/main/examples/README.md
|
| 234 |
-
6. Hard brief, 4S LiFePO4 BMS: https://github.com/copperheadhq/copperhead/blob/main/examples/hard/lifepo4-bms.md
|
| 235 |
-
7. Medium brief, dual brushed-DC motor driver: https://github.com/copperheadhq/copperhead/blob/main/examples/medium/dual-brushed-dc-motor-driver.md
|
| 236 |
-
8. Fang repository and docs: https://github.com/copperheadhq/fang · https://fang.copperhead.sh
|
| 237 |
-
9. Fang `servo_drive` example: https://github.com/copperheadhq/fang/tree/main/examples/servo_drive
|
| 238 |
-
10. Copperhead on X, 400 V/10 A gate-drive simulation: https://x.com/copperheadhq/status/2111021836310118742
|
| 239 |
-
11. Copperhead on X, Fang thermal and MC34063 checks: https://x.com/copperheadhq/status/2108111703141699785 · https://x.com/copperheadhq/status/2107169309659435409
|
| 240 |
-
12. Copperhead on X, openEMS antenna simulation: https://x.com/copperheadhq/status/2107451867701858779
|
| 241 |
-
13. Copperhead on X, firmware simulation: https://x.com/copperheadhq/status/2106386087635812737
|
| 242 |
-
14. Careers, Forward Deployed Hardware Engineer (CM5 carrier project): https://copperhead.sh/careers/forward-deployed-hardware-engineer/
|
| 243 |
-
15. Careers, Senior AI PCB Design Engineer (industry nice-to-haves): https://copperhead.sh/careers/senior-ai-pcb-design-engineer/
|
| 244 |
-
16. STM32 data logger example: https://github.com/copperheadhq/copperhead-stm32-data-logger
|
| 245 |
-
17. Review prompts (v0.12.0): https://github.com/copperheadhq/copperhead/blob/main/src/review/prompts.ts
|
| 246 |
-
18. copperbench: https://copperbench.org · standard: https://copperbench.org/standard
|
| 247 |
-
19. Copperhead on X, datasheet-limit checks ("33 of 35"): https://x.com/copperheadhq/status/2106006961255002223
|
| 248 |
-
20. Copperhead homepage: https://copperhead.sh
|
| 249 |
-
21. Blog, "Hardware as fast as software" (Kyra demo): https://copperhead.sh/blog/hardware-as-fast-as-software/
|
| 250 |
-
22. Blog, LED bulb teardown: https://copperhead.sh/blog/crompton-led-bulb-teardown/
|
| 251 |
-
23. Quiet Orbit LED board: https://github.com/copperheadhq/copperhead-quiet-orbit
|
| 252 |
-
|
| 253 |
-
**KiCad**
|
| 254 |
-
|
| 255 |
-
24. KiCad 9.0 release notes (creepage DRC): https://www.kicad.org/blog/2025/02/Version-9.0.0-Released/
|
| 256 |
-
25. KiCad forum, using creepage custom rules: https://forum.kicad.info/t/how-do-i-use-the-new-creepage-custom-rules-v9-0-0/59328
|
| 257 |
-
26. KiCad custom rule constraints (diff_pair_gap, length, skew): https://github.com/KiCad/kicad-source-mirror/blob/c81ed537/pcbnew/dialogs/panel_setup_rules_help_2constraints.h
|
| 258 |
-
27. KiCad command-line interface docs: https://docs.kicad.org/9.0/en/cli/cli.html
|
| 259 |
-
|
| 260 |
-
**Standards, fabs and industry practice**
|
| 261 |
-
|
| 262 |
-
28. IPC-2152 (ANSI webstore summary): https://webstore.ansi.org/standards/ipc/IPC21522009
|
| 263 |
-
29. Sierra Circuits, trace current capacity: https://www.protoexpress.com/blog/trace-current-capacity-pcb-design/
|
| 264 |
-
30. IPC-2221 Table 6-1 conductor spacing (reproduced by Altair): https://help.altair.com/pollex/topics/pollex/verification/dfe_ipc_material_r.htm
|
| 265 |
-
31. TI SLUP419, creepage and clearance standards (IEC 60664-1, IEC 61800-5-1): https://www.ti.com/lit/pdf/slup419
|
| 266 |
-
32. Creepage.com, IEC 62368-1 calculator (third-party tool): https://www.creepage.com/
|
| 267 |
-
33. Analog Devices, IEC 61010-1 Edition 3: https://www.analog.com/media/en/technical-documentation/technical-articles/iec-61010-1-edition-3.pdf
|
| 268 |
-
34. Analog Devices, protection strategies for medical device safety (MOOP/MOPP table): https://www.analog.com/en/resources/technical-articles/dont-get-zapped.html
|
| 269 |
-
35. PCB International, IPC-6012 class differences: https://www.pcbinternational.com/tech/ipcrequirementdifferences/
|
| 270 |
-
36. ACDI, IPC Class 2 vs Class 3: https://www.acdi.com/ipc-class-2-vs-class-3-assembly-processes-what-is-the-difference-part-1/
|
| 271 |
-
37. JLCPCB capabilities: https://jlcpcb.com/capabilities/
|
| 272 |
-
38. JLCPCB, standard laminated structures and impedance testing: https://jlcpcb.com/help/article/multi-layer-pcb-standard-laminated-structures
|
| 273 |
-
39. Electronics Brief, ICT vs flying probe vs functional test: https://www.electronicsbrief.com/articles/ict-vs-flying-probe-vs-functional-test
|
| 274 |
-
40. XJTAG, boundary scan FAQ: https://www.xjtag.com/support/faq/faq-jtag-boundary-scan/
|
| 275 |
-
41. Circuitnet, general design rules for conformal coating (white paper): https://www.circuitnet.com/news/uploads/2/General_Design_Rules_for_Conformal_coating_WHITE_PAPER.pdf
|
| 276 |
-
42. PCBWay, panelization, rails, fiducials, tooling holes: https://www.pcbway.com/helpcenter/design_instruction/PCB_Panelization__Breakaway_Rails__Fiducial_Marks__Tooling_Holes.html
|
| 277 |
-
43. CALCE (University of Maryland), part obsolescence: https://calce.umd.edu/electronic-part-obsolescence-forecasting-mitigation-and-management
|
| 278 |
-
44. Compatible Electronics, EMC testing cost guide: https://www.celectronics.com/Resources/EMC-Testing-Cost-Guide
|
| 279 |
-
45. EMI Software, first-time EMC failure rates (citing Intertek): https://www.emisoftware.com/blogs/percentage-products-fail-emc-tests-first-time/
|
| 280 |
-
46. TI SLYT614, five steps to a great step-down converter layout: https://www.ti.com/lit/an/slyt614/slyt614.pdf
|
| 281 |
-
47. TI SLUA736, lightning surge considerations for PoE powered devices: https://www.ti.com/lit/an/slua736/slua736.pdf
|
| 282 |
-
48. Espressif, ESP32 PCB layout design: https://docs.espressif.com/projects/esp-hardware-design-guidelines/en/latest/esp32/pcb-layout-design.html
|
| 283 |
-
49. FCC KDB 996369 D04, modular transmitter integration guide: https://apps.fcc.gov/kdb/GetAttachment.html?desc=996369+D04+Module+Integration+Guide+V02&id=bNCiEdkFEKnHsZF9GHCNdg%3D%3D&tracking_number=44637
|
| 284 |
-
50. TI SPRAAR7, high-speed interface layout guidelines: https://www.ti.com/lit/an/spraar7/spraar7.pdf
|
| 285 |
-
51. Raspberry Pi Compute Module 5 datasheet: https://datasheets.raspberrypi.com/cm5/cm5-datasheet.pdf
|
| 286 |
-
52. Analog Devices MT-031, grounding data converters: https://www.analog.com/mt-031
|
| 287 |
-
53. TI SLVA959, best practices for board layout of motor drivers: https://www.ti.com/lit/an/slva959b/slva959b.pdf
|
| 288 |
-
54. TI E2E FAQ, connecting cells to BQ769x2 monitors · TI fuel-gauge PCB layout guidance: https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/1176908/faq-bq76952-connecting-battery-cells-to-the-bq769x2-family-of-monitors · https://www.ti.com/content/dam/videos/external-videos/en-us/1/3816841626001/3877771975001.mp4/subassets/pcb-layout-guidelines-fuel-gauge-design-presentation.pdf
|
| 289 |
-
55. Analog Devices, industrial digital inputs with the MAX22191 (IEC 61131-2 types): https://www.analog.com/en/resources/design-notes/industrial-digital-inputs-with-the-max22191.html
|
| 290 |
-
56. TI SLLA272, the RS-485 design guide · TI SLLA416, isolating RS-485 signal and power: https://www.ti.com/lit/an/slla272d/slla272d.pdf · https://www.ti.com/lit/ab/slla416c/slla416c.pdf
|
| 291 |
-
57. TI SNVA238, thermal performance of LM3404 (metal-core PCB): https://www.ti.com/lit/an/snva238a/snva238a.pdf
|
| 292 |
-
58. Automotive Electronics Council documents (AEC-Q100, AEC-Q200): http://www.aecouncil.com/Documents/AECDocuments.html
|
| 293 |
-
59. Analog Devices, load-dump protection for automotive applications: https://www.analog.com/en/resources/technical-articles/loaddump-protection-for-24v-automotive-applications.html
|
| 294 |
-
60. ISO 26262-5:2018 (hardware level): https://www.iso.org/standard/68387.html
|
| 295 |
-
61. exida, IEC 61508 overview: https://www.exida.com/articles/IEC-61508-Overview.pdf
|
| 296 |
-
62. FAA AC 20-152A, development assurance for airborne electronic hardware: https://www.faa.gov/documentLibrary/media/Advisory_Circular/AC_20-152A.pdf
|
| 297 |
-
63. Betaflight flight controller manufacturer design guidelines (v3.0, 2026-09-28): https://betaflight.com/docs/development/manufacturer/manufacturer-design-guidelines
|
| 298 |
-
64. PX4 reference flight controller design and vibration isolation: https://docs.px4.io/main/en/hardware/reference_design · https://docs.px4.io/main/en/assembly/vibration_isolation
|
| 299 |
-
65. Siemens, PCB high-voltage spacing: https://blogs.sw.siemens.com/electronic-systems-design/2025/04/29/pcb-high-voltage-spacing-what-every-engineer-should-know/
|
| 300 |
-
66. TI SNLA426, high-speed PCB layout for PCIe Gen 5: https://www.ti.com/lit/an/snla426/snla426.pdf
|
| 301 |
-
67. TI ISO1212 isolated 24 V digital input receiver datasheet: https://www.ti.com/lit/gpn/ISO1212
|
| 302 |
-
68. TI TIDA-00548, isolated dual-channel 4-20 mA analog input reference design: https://www.ti.com/tool/TIDA-00548
|
| 303 |
-
69. Founder on X, "we are building claude code for robot electronics": https://x.com/animeshsingh38/status/2082702268990931032
|
| 304 |
-
70. Copperhead on X, reply guessing at third-party drone boards: https://x.com/copperheadhq/status/2106969953509540263
|
| 305 |
-
71. Copperhead pricing: https://copperhead.sh/pricing/
|
|
|
|
| 4 |
tags: [pcb, kicad, electronics]
|
| 5 |
---
|
| 6 |
|
| 7 |
+
# Copperhead circuit buckets: one-page list
|
| 8 |
+
|
| 9 |
+
## Good fit now
|
| 10 |
+
- **MCU control and dev boards**: RP2040, ESP32 or STM32 boards. Matters: power tree and decoupling; 90 Ω USB pair; boot pins. Why this fit: core of its demo record.
|
| 11 |
+
- **Sensor and IoT nodes (module-based)**: ESP32 soil sensor, BLE beacon. Matters: µA sleep budget; antenna keep-out; pre-certified module. Why this fit: low layout risk.
|
| 12 |
+
- **Simple low-voltage regulators**: 12 V to 5 V buck, LDO rails. Matters: tight input-capacitor loop; IPC-2152 widths; thermal. Why this fit: Fang buck demo.
|
| 13 |
+
- **Single-cell chargers**: Li-ion charger with fuel gauge. Matters: charger datasheet compliance; thermal. Why this fit: used in its logger demo.
|
| 14 |
+
- **Low-voltage LED boards**: PWM LED board. Matters: thermal path; current accuracy. Why this fit: LED demo board.
|
| 15 |
+
|
| 16 |
+
## Partial: needs a human for layout
|
| 17 |
+
- **Motor drives and robotics**: brushed-DC driver, 24 V servo drive. Matters: short power loop; gate loop; heavy copper; thermal. Why this fit: servo drive is netlist only.
|
| 18 |
+
- **Multi-cell low-voltage BMS**: 4S–16S BMS. Matters: Kelvin sensing; FET current path; protection timing. Why this fit: own example rated "hard".
|
| 19 |
+
- **Industrial I/O**: 24 V PLC inputs, RS-485, 4–20 mA. Matters: IEC 61131-2 behaviour; isolation; surge. Why this fit: no creepage rules.
|
| 20 |
+
- **USB-PD supplies and PoE**: 100 W bench supply, PoE device. Matters: switching layout; 1500 V PoE isolation; EMC. Why this fit: no isolation net class.
|
| 21 |
+
- **Precision analog and audio**: ADC front end, microphone board. Matters: grounding; noise; drift. Why this fit: layout decides.
|
| 22 |
+
- **Drone flight controllers**: Betaflight-style FC boards. Matters: clean IMU supply; dedicated gyro SPI bus; vibration. Why this fit: dense layout.
|
| 23 |
+
- **Automotive controller prototypes**: CAN node, vehicle control unit. Matters: load-dump protection; AEC-Q parts; CISPR 25. Why this fit: no AEC-Q filtering.
|
| 24 |
+
- **SBC/SoM carrier boards**: CM5 or Jetson carrier. Matters: controlled impedance; length matching; stackup. Why this fit: human-led; no impedance defaults.
|
| 25 |
+
|
| 26 |
+
## Out of reach
|
| 27 |
+
- **Chip-down high-speed digital**: DDR or PCIe processor boards. Matters: impedance; return paths; signal integrity. Why this fit: no impedance rules.
|
| 28 |
+
- **Chip-down RF**: discrete-matched radio, 5.8 GHz transmitter. Matters: 50 Ω lines; matching; certification. Why this fit: rated "hard".
|
| 29 |
+
- **High-current ESCs**: 4-in-1 drone ESC. Matters: power loop; heavy copper; thermal. Why this fit: routing left to humans.
|
| 30 |
+
- **High-voltage and mains power**: offline SMPS, inverter, on-board charger, high-voltage BMS. Matters: creepage; magnetics; certification. Why this fit: no creepage rules.
|
| 31 |
+
- **Medical and safety-certified production**: patient monitor, ISO 26262 or DO-254 hardware. Matters: 2×MOPP isolation; safety analysis; certification. Why this fit: process work, not PCB tooling.
|
| 32 |
+
|
| 33 |
+
## Easiest to check automatically
|
| 34 |
+
- MCU control and dev boards
|
| 35 |
+
- Module-based sensor and IoT nodes
|
| 36 |
+
- Simple low-voltage regulators
|
| 37 |
+
- Precision analog (circuit level)
|
| 38 |
+
- Drone flight controllers (netlist rules)
|
| 39 |
+
- Industrial I/O (schematic side)
|
| 40 |
+
|
| 41 |
+
## Open questions
|
| 42 |
+
- Does the Copperhead CLI call Fang simulation? [UNVERIFIED]
|
| 43 |
+
- Do IEC 62619 / UL 2580 apply to the BMS boards in scope? [UNVERIFIED]
|
| 44 |
+
- Can Copperhead or Fang run full signal-integrity simulation? [UNVERIFIED]
|
| 45 |
+
- Are AEC-Q filtering and ISO 26262 work truly absent? [UNVERIFIED]
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|