id large_stringlengths 21 21 | domain large_stringclasses 7
values | instruction large_stringclasses 115
values | reasoning large_stringlengths 1.07k 5.05k | response large_stringlengths 677 1.11k | text large_stringlengths 2.31k 6.39k | target_board_id large_stringclasses 863
values | mcu large_stringclasses 201
values | vendor large_stringclasses 231
values | ram_bytes int64 2.05k 8.59B | rom_bytes int64 0 1.07B |
|---|---|---|---|---|---|---|---|---|---|---|
pyintel_hw_cot_002500 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 156 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **RoboHeart Hercules**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `roboheart_hercules` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficie... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 156 KB of unfragmented dynamic heap (accounting f... | roboheart_hercules | ESP32 | RoboHeart | 327,680 | 4,194,304 |
pyintel_hw_cot_002501 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 fr... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 500 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (24V). Requires wide DC input step-down regulator or automo... | ### Recommended Board: **MakerAsia Nano32**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `nano32` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, bluetooth, ethernet, can | Hardware fram... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling cap... | nano32 | ESP32 | MakerAsia | 327,680 | 4,194,304 |
pyintel_hw_cot_002502 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 112 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **XinaBox CW02**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `xinabox_cw02` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient throughpu... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 112 KB of unfragmented dynamic heap (accounting f... | xinabox_cw02 | ESP32 | XinaBox | 327,680 | 4,194,304 |
pyintel_hw_cot_002503 | native_usb_emulation | I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoin... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Cookie RP2040**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `melopero_cookie_rp2040` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2040` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom H... | <start_of_turn>user
I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting ... | melopero_cookie_rp2040 | RP2040 | Melopero | 262,144 | 8,388,608 |
pyintel_hw_cot_002504 | native_usb_emulation | I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoin... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Cytron Maker Feather AIoT S3**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `cytron_maker_feather_aiot_s3` | Registered entry in Open Board Registry |
| **Microcontroller** | `ESP32S3` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Na... | <start_of_turn>user
I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting ... | cytron_maker_feather_aiot_s3 | ESP32S3 | Cytron Technologies | 327,680 | 8,388,608 |
pyintel_hw_cot_002505 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 f... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 2000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (24V). Requires wide DC input step-down regulator or autom... | ### Recommended Board: **ST Nucleo L496ZG-P**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `nucleo_l496zg_p` | Registered open-hardware entry |
| **MCU Architecture** | `STM32L496ZGT6P` | High-speed real-time core |
| **CAN Bus Interface** | can | Hardware frame filtr... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling ca... | nucleo_l496zg_p | STM32L496ZGT6P | ST | 327,680 | 1,048,576 |
pyintel_hw_cot_002506 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 25 kHz PWM, each control cycle is $T = 1 / 25\text{ kHz} = 40.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **YD RP2040**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `vccgnd_yd_rp2040` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** | 133 MHz | Completes FOC ... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | vccgnd_yd_rp2040 | RP2040 | VCC-GND | 262,144 | 16,777,216 |
pyintel_hw_cot_002507 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **Connectivity 2040 LTE/WiFi/BLE**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
|... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | connectivity_2040_lte_wifi_ble | RP2040 | iLabs | 262,144 | 8,388,608 |
pyintel_hw_cot_002508 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 44.1 kHz 16-bit mono produces $44.1 \times 10^3 \times 2 \approx 88,200 \text{ bytes/sec}$.
- **FFT Window Duration**: A 2048-point buffer represents $T_{window} = 2048 / (44.1 \times 10^3) \approx 46.44 \text{ ms}$.
- **Processin... | ### Recommended Board: **Armstrap Eagle 512**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `armstrap_eagle512` | Verified Open Board Registry entry |
| **Processor Core** | `STM32F407VET6` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 168 MHz | FFT computes in $< 2 \text{ ... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | armstrap_eagle512 | STM32F407VET6 | Armstrap | 131,072 | 524,288 |
pyintel_hw_cot_002509 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **YeaCreate NSCREEN-32**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Con... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | nscreen-32 | ESP32 | YeaCreate | 327,680 | 16,777,216 |
pyintel_hw_cot_002510 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 48.0 kHz 16-bit mono produces $48.0 \times 10^3 \times 2 \approx 96,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 2048-point buffer represents $T_{window} = 2048 / (48.0 \times 10^3) \approx 42.67 \text{ ms}$.
- **Processin... | ### Recommended Board: **Node32s**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `node32s` | Verified Open Board Registry entry |
| **Processor Core** | `ESP32` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 240 MHz | FFT computes in $< 2 \text{ ms}$ (well below 42.7 ms fram... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | node32s | ESP32 | Aiyarafun | 327,680 | 4,194,304 |
pyintel_hw_cot_002511 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S doub... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 44.1 kHz 16-bit mono produces $44.1 \times 10^3 \times 2 \approx 88,200 \text{ bytes/sec}$.
- **FFT Window Duration**: A 512-point buffer represents $T_{window} = 512 / (44.1 \times 10^3) \approx 11.61 \text{ ms}$.
- **Processing ... | ### Recommended Board: **STM32F103VE (64k RAM. 512k Flash)**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `genericSTM32F103VE` | Verified Open Board Registry entry |
| **Processor Core** | `STM32F103VET6` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 72 MHz | FFT computes ... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support c... | genericSTM32F103VE | STM32F103VET6 | Generic | 65,536 | 524,288 |
pyintel_hw_cot_002512 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 428 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **Espressif ESP32-S2-Saola-1**
| Constraint Parameter | Required Budget | Board Capability (`esp32-s2-saola-1`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 96 KB | Supported with substantial ... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 428 KB of conti... | esp32-s2-saola-1 | ESP32S2 | Espressif | 327,680 | 4,194,304 |
pyintel_hw_cot_002513 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 148 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **WL2S Wi-Fi/BLE Module**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `wl2s` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `LN882HK` | Native dual-core/accelerated processing |
| **Operating Frequency** | 160 MHz | Sufficient throug... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 148 KB of unfragmented dynamic heap (accounting f... | wl2s | LN882HK | Unknown | 302,080 | 1,228,800 |
pyintel_hw_cot_002514 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 fr... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 500 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (24V). Requires wide DC input step-down regulator or automo... | ### Recommended Board: **Labplus mPython**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `labplus_mpython` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, bluetooth, ethernet, can | Hardw... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling cap... | labplus_mpython | ESP32 | Labplus | 327,680 | 4,194,304 |
pyintel_hw_cot_002515 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 f... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 2000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (12V). Requires wide DC input step-down regulator or autom... | ### Recommended Board: **ST Nucleo L486RG**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `nucleo_l486rg` | Registered open-hardware entry |
| **MCU Architecture** | `STM32L486RGT6` | High-speed real-time core |
| **CAN Bus Interface** | can | Hardware frame filtration... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling ca... | nucleo_l486rg | STM32L486RGT6 | ST | 131,072 | 1,048,576 |
pyintel_hw_cot_002516 | native_usb_emulation | I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoin... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **RP2040 Zero**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `waveshare_rp2040_zero` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2040` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HID/... | <start_of_turn>user
I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting ... | waveshare_rp2040_zero | RP2040 | Waveshare | 262,144 | 2,097,152 |
pyintel_hw_cot_002517 | native_usb_emulation | I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable en... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Sea-Picro**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `sea_picro` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2040` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HID/MIDI/CDC descr... | <start_of_turn>user
I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY suppor... | sea_picro | RP2040 | Generic | 262,144 | 8,388,608 |
pyintel_hw_cot_002518 | native_usb_emulation | I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable en... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Teensy 2.0**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `teensy2` | Registered entry in Open Board Registry |
| **Microcontroller** | `ATMEGA32U4` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HID/MIDI/CDC de... | <start_of_turn>user
I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY suppor... | teensy2 | ATMEGA32U4 | Teensy | 2,560 | 32,256 |
pyintel_hw_cot_002519 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 428 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **Plasma2040**
| Constraint Parameter | Required Budget | Board Capability (`pimoroni_plasma2040`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 96 KB | Supported with substantial overhead |
| ... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 428 KB of conti... | pimoroni_plasma2040 | RP2040 | Pimoroni | 262,144 | 2,097,152 |
pyintel_hw_cot_002520 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **RP2350**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Controller** | Ha... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | generic_rp2350 | RP2350 | Generic | 524,288 | 16,777,216 |
pyintel_hw_cot_002521 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 120 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Adafruit QT Py ESP32-C3**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `adafruit_qtpy_esp32c3` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32C3` | Native dual-core/accelerated processing |
| **Operating Frequency** | 160 MHz ... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 120 KB of unfragmented dynamic heap (accounting f... | adafruit_qtpy_esp32c3 | ESP32C3 | Adafruit | 327,680 | 4,194,304 |
pyintel_hw_cot_002522 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **BluesWireless Swan R5**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Co... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | bw_swan_r5 | STM32L4R5ZIY6 | BluesWireless | 655,360 | 2,097,152 |
pyintel_hw_cot_002523 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 140 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Espressif ESP32-C3-DevKitC-02**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `esp32-c3-devkitc-02` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32C3` | Native dual-core/accelerated processing |
| **Operating Frequency** | 160 ... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 140 KB of unfragmented dynamic heap (accounting f... | esp32-c3-devkitc-02 | ESP32C3 | Espressif | 327,680 | 4,194,304 |
pyintel_hw_cot_002524 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 246 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 320 pixels width $\times$ 240 pixels height = 76,800 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $320 \times 240 \times 2 = 153,600 \text{ bytes} = 150 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **ProMicro RP2040**
| Constraint Parameter | Required Budget | Board Capability (`sparkfun_promicrorp2040`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 150 KB (320x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 64 KB | Supported with substantial over... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 246 KB of conti... | sparkfun_promicrorp2040 | RP2040 | SparkFun | 262,144 | 16,777,216 |
pyintel_hw_cot_002525 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 156 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **ETBoard**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `etboard` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient throughput for TLS ... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 156 KB of unfragmented dynamic heap (accounting f... | etboard | ESP32 | ETBoard | 327,680 | 4,194,304 |
pyintel_hw_cot_002526 | native_usb_emulation | I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable en... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **RedBearLab Blend Micro 3.3V/16MHz (overclock)**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `blendmicro16` | Registered entry in Open Board Registry |
| **Microcontroller** | `ATMEGA32U4` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB ... | <start_of_turn>user
I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY suppor... | blendmicro16 | ATMEGA32U4 | RedBearLab | 2,560 | 28,672 |
pyintel_hw_cot_002527 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capab... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 1000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (7V–28V DC wide input). Requires wide DC input step-down r... | ### Recommended Board: **Adafruit Hallowing M0**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `adafruit_hallowing` | Registered open-hardware entry |
| **MCU Architecture** | `SAMD21G18A` | High-speed real-time core |
| **CAN Bus Interface** | | Hardware frame filtra... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient inte... | adafruit_hallowing | SAMD21G18A | Adafruit | 32,768 | 262,144 |
pyintel_hw_cot_002528 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Nano RP2040 Connect**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `arduino_nano_connect` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** | 133 MHz | ... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | arduino_nano_connect | RP2040 | Arduino | 262,144 | 16,777,216 |
pyintel_hw_cot_002529 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 f... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 1000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (12V). Requires wide DC input step-down regulator or autom... | ### Recommended Board: **M5Stack GREY ESP32**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `m5stack-grey` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, bluetooth, ethernet, can | Hardw... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling ca... | m5stack-grey | ESP32 | M5Stack | 532,480 | 16,777,216 |
pyintel_hw_cot_002530 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **W6300-EVB-Pico**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `wiznet_6300_evb_pico` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** | 133 MHz | Compl... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | wiznet_6300_evb_pico | RP2040 | WIZnet | 262,144 | 2,097,152 |
pyintel_hw_cot_002531 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S doub... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 48.0 kHz 16-bit mono produces $48.0 \times 10^3 \times 2 \approx 96,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 512-point buffer represents $T_{window} = 512 / (48.0 \times 10^3) \approx 10.67 \text{ ms}$.
- **Processing ... | ### Recommended Board: **Hexiwear**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `hexiwear` | Verified Open Board Registry entry |
| **Processor Core** | `MK64FN1M0VDC12` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 120 MHz | FFT computes in $< 2 \text{ ms}$ (well below 1... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support c... | hexiwear | MK64FN1M0VDC12 | MikroElektronika | 262,144 | 1,048,576 |
pyintel_hw_cot_002532 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 112 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **WB1S Wi-Fi Module**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `wb1s` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `BK7231T` | Native dual-core/accelerated processing |
| **Operating Frequency** | 120 MHz | Sufficient throughput... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 112 KB of unfragmented dynamic heap (accounting f... | wb1s | BK7231T | Tuya Inc. | 262,144 | 1,083,136 |
pyintel_hw_cot_002533 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 fr... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 500 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (12V). Requires wide DC input step-down regulator or automo... | ### Recommended Board: **L476DMW1K**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `rhombio_l476dmw1k` | Registered open-hardware entry |
| **MCU Architecture** | `STM32L476VGT6` | High-speed real-time core |
| **CAN Bus Interface** | can | Hardware frame filtration & ... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling cap... | rhombio_l476dmw1k | STM32L476VGT6 | rhomb.io | 131,072 | 1,048,576 |
pyintel_hw_cot_002534 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 214 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 320 pixels width $\times$ 240 pixels height = 76,800 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $320 \times 240 \times 2 = 153,600 \text{ bytes} = 150 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **Raspberry Pi 1 Model B**
| Constraint Parameter | Required Budget | Board Capability (`raspberrypi_1b`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 150 KB (320x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 32 KB | Supported with substantial overhe... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 214 KB of conti... | raspberrypi_1b | BCM2835 | Raspberry Pi | 536,870,912 | 536,870,912 |
pyintel_hw_cot_002535 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **Blues Cygnet**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Controller*... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | blues_cygnet | STM32L433CCT6 | Blues | 65,536 | 262,144 |
pyintel_hw_cot_002536 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 132 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **4D Systems GEN4-ESP32 16MB (ESP32S3-R8N16)**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `4d_systems_esp32s3_gen4_r8n16` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32S3` | Native dual-core/accelerated processing |
| **Opera... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 132 KB of unfragmented dynamic heap (accounting f... | 4d_systems_esp32s3_gen4_r8n16 | ESP32S3 | 4D Systems | 327,680 | 16,777,216 |
pyintel_hw_cot_002537 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capab... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 2000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (7V–28V DC wide input). Requires wide DC input step-down r... | ### Recommended Board: **BluesWireless Swan R5**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `bw_swan_r5` | Registered open-hardware entry |
| **MCU Architecture** | `STM32L4R5ZIY6` | High-speed real-time core |
| **CAN Bus Interface** | can | Hardware frame filtrati... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient inte... | bw_swan_r5 | STM32L4R5ZIY6 | BluesWireless | 655,360 | 2,097,152 |
pyintel_hw_cot_002538 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 25 kHz PWM, each control cycle is $T = 1 / 25\text{ kHz} = 40.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Blues Cygnet**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `blues_cygnet` | Verified Open Board Registry entry |
| **MCU Core** | `STM32L433CCT6` | High-speed real-time core with hardware math |
| **Core Clock** | 80 MHz | Completes... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | blues_cygnet | STM32L433CCT6 | Blues | 65,536 | 262,144 |
pyintel_hw_cot_002539 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 428 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **RP2040 Matrix**
| Constraint Parameter | Required Budget | Board Capability (`waveshare_rp2040_matrix`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 96 KB | Supported with substantial overhe... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 428 KB of conti... | waveshare_rp2040_matrix | RP2040 | Waveshare | 262,144 | 2,097,152 |
pyintel_hw_cot_002540 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 44.1 kHz 16-bit mono produces $44.1 \times 10^3 \times 2 \approx 88,200 \text{ bytes/sec}$.
- **FFT Window Duration**: A 2048-point buffer represents $T_{window} = 2048 / (44.1 \times 10^3) \approx 46.44 \text{ ms}$.
- **Processin... | ### Recommended Board: **Adafruit ESP32-S2 Feather Development Board**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `featheresp32-s2` | Verified Open Board Registry entry |
| **Processor Core** | `ESP32S2` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 240 MHz | FFT compute... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | featheresp32-s2 | ESP32S2 | Adafruit | 327,680 | 4,194,304 |
pyintel_hw_cot_002541 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capab... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 1000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (7V–28V DC wide input). Requires wide DC input step-down r... | ### Recommended Board: **Denky D4 (PICO-V3-02)**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `denky_d4` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, bluetooth, ethernet, can | Hardwa... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient inte... | denky_d4 | ESP32 | Denky | 327,680 | 8,388,608 |
pyintel_hw_cot_002542 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 156 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **LilyGo T-Display**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `lilygo-t-display` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient t... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 156 KB of unfragmented dynamic heap (accounting f... | lilygo-t-display | ESP32 | LilyGo | 327,680 | 4,194,304 |
pyintel_hw_cot_002543 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 144 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Espressif ESP32-C3-DevKitM-1**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `esp32-c3-devkitm-1` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32C3` | Native dual-core/accelerated processing |
| **Operating Frequency** | 160 MH... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 144 KB of unfragmented dynamic heap (accounting f... | esp32-c3-devkitm-1 | ESP32C3 | Espressif | 327,680 | 4,194,304 |
pyintel_hw_cot_002544 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 428 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **WeAct Studio MiniSTM32H743VITX**
| Constraint Parameter | Required Budget | Board Capability (`weact_mini_h743vitx`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 96 KB | Supported with subst... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 428 KB of conti... | weact_mini_h743vitx | STM32H743VIT6 | WeAct Studio | 524,288 | 2,097,152 |
pyintel_hw_cot_002545 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 44.1 kHz 16-bit mono produces $44.1 \times 10^3 \times 2 \approx 88,200 \text{ bytes/sec}$.
- **FFT Window Duration**: A 1024-point buffer represents $T_{window} = 1024 / (44.1 \times 10^3) \approx 23.22 \text{ ms}$.
- **Processin... | ### Recommended Board: **Adafruit Feather ESP32-S3 2MB PSRAM**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `adafruit_feather_esp32s3` | Verified Open Board Registry entry |
| **Processor Core** | `ESP32S3` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 240 MHz | FFT comput... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | adafruit_feather_esp32s3 | ESP32S3 | Adafruit | 327,680 | 4,194,304 |
pyintel_hw_cot_002546 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **u-blox C030-R410M IoT**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Co... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | ublox_c030_r410m | STM32F437VG | u-blox | 262,144 | 1,048,576 |
pyintel_hw_cot_002547 | native_usb_emulation | I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoi... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Metro RP2350**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `adafruit_metro_rp2350` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2350` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HID... | <start_of_turn>user
I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting... | adafruit_metro_rp2350 | RP2350 | Adafruit | 524,288 | 16,777,216 |
pyintel_hw_cot_002548 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capab... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 2000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (7V–28V DC wide input). Requires wide DC input step-down r... | ### Recommended Board: **ST 32L496GDISCOVERY**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `disco_l496ag` | Registered open-hardware entry |
| **MCU Architecture** | `STM32L496AGI6` | High-speed real-time core |
| **CAN Bus Interface** | can | Hardware frame filtrati... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient inte... | disco_l496ag | STM32L496AGI6 | ST | 327,680 | 1,048,576 |
pyintel_hw_cot_002549 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **STM32F412RE (256k RAM. 512k Flash)**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated)... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | genericSTM32F412RE | STM32F412RET6 | Generic | 262,144 | 524,288 |
pyintel_hw_cot_002550 | native_usb_emulation | I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoin... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **SparkFun Fio V3 3.3V/8MHz**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `sparkfun_fiov3` | Registered entry in Open Board Registry |
| **Microcontroller** | `ATMEGA32U4` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | ... | <start_of_turn>user
I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting ... | sparkfun_fiov3 | ATMEGA32U4 | SparkFun | 2,560 | 28,672 |
pyintel_hw_cot_002551 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 f... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 2000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (24V). Requires wide DC input step-down regulator or autom... | ### Recommended Board: **ST Nucleo F042K6**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `nucleo_f042k6` | Registered open-hardware entry |
| **MCU Architecture** | `STM32F042K6T6` | High-speed real-time core |
| **CAN Bus Interface** | can | Hardware frame filtration... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling ca... | nucleo_f042k6 | STM32F042K6T6 | ST | 6,144 | 32,768 |
pyintel_hw_cot_002552 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 164 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Unexpected Maker TinyS3**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `um_tinys3` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32S3` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 164 KB of unfragmented dynamic heap (accounting f... | um_tinys3 | ESP32S3 | Unexpected Maker | 327,680 | 8,388,608 |
pyintel_hw_cot_002553 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 124 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **M5Stack AtomS3**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `m5stack-atoms3` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32S3` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient thr... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 124 KB of unfragmented dynamic heap (accounting f... | m5stack-atoms3 | ESP32S3 | M5Stack | 327,680 | 8,388,608 |
pyintel_hw_cot_002554 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **STM32F413CH (320k RAM. 1536k Flash)**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | genericSTM32F413CH | STM32F413CHU6 | Generic | 327,680 | 1,572,864 |
pyintel_hw_cot_002555 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 48.0 kHz 16-bit mono produces $48.0 \times 10^3 \times 2 \approx 96,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 1024-point buffer represents $T_{window} = 1024 / (48.0 \times 10^3) \approx 21.33 \text{ ms}$.
- **Processin... | ### Recommended Board: **STM32F407VE (192k RAM. 512k Flash)**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `genericSTM32F407VET6` | Verified Open Board Registry entry |
| **Processor Core** | `STM32F407VET6` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 168 MHz | FFT compu... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | genericSTM32F407VET6 | STM32F407VET6 | Generic | 131,072 | 514,288 |
pyintel_hw_cot_002556 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 112 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **WB2S Wi-Fi Module**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `wb2s` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `BK7231T` | Native dual-core/accelerated processing |
| **Operating Frequency** | 120 MHz | Sufficient throughput... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 112 KB of unfragmented dynamic heap (accounting f... | wb2s | BK7231T | Tuya Inc. | 262,144 | 1,083,136 |
pyintel_hw_cot_002557 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 40 kHz PWM, each control cycle is $T = 1 / 40\text{ kHz} = 25.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **RushUp Cloud-JAM**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `cloud_jam` | Verified Open Board Registry entry |
| **MCU Core** | `STM32F401RET6` | High-speed real-time core with hardware math |
| **Core Clock** | 84 MHz | Complete... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | cloud_jam | STM32F401RET6 | RushUp | 98,304 | 524,288 |
pyintel_hw_cot_002558 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 44.1 kHz 16-bit mono produces $44.1 \times 10^3 \times 2 \approx 88,200 \text{ bytes/sec}$.
- **FFT Window Duration**: A 1024-point buffer represents $T_{window} = 1024 / (44.1 \times 10^3) \approx 23.22 \text{ ms}$.
- **Processin... | ### Recommended Board: **STM32F407VE (192k RAM. 512k Flash)**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `genericSTM32F407VET6` | Verified Open Board Registry entry |
| **Processor Core** | `STM32F407VET6` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 168 MHz | FFT compu... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | genericSTM32F407VET6 | STM32F407VET6 | Generic | 131,072 | 514,288 |
pyintel_hw_cot_002559 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 25 kHz PWM, each control cycle is $T = 1 / 25\text{ kHz} = 40.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **STM32F103VG (96k RAM. 1024k Flash)**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `genericSTM32F103VG` | Verified Open Board Registry entry |
| **MCU Core** | `STM32F103VGT6` | High-speed real-time core with hardware math |
| **Core ... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | genericSTM32F103VG | STM32F103VGT6 | Generic | 98,304 | 1,048,576 |
pyintel_hw_cot_002560 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S doub... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 44.1 kHz 16-bit mono produces $44.1 \times 10^3 \times 2 \approx 88,200 \text{ bytes/sec}$.
- **FFT Window Duration**: A 512-point buffer represents $T_{window} = 512 / (44.1 \times 10^3) \approx 11.61 \text{ ms}$.
- **Processing ... | ### Recommended Board: **96Boards Neonkey**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `b96b_neonkey` | Verified Open Board Registry entry |
| **Processor Core** | `STM32F411CE` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 100 MHz | FFT computes in $< 2 \text{ ms}$ (wel... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support c... | b96b_neonkey | STM32F411CE | 96Boards | 131,072 | 524,288 |
pyintel_hw_cot_002561 | native_usb_emulation | I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable en... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **senseBox MCU-S2 ESP32-S2**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `sensebox_mcu_esp32s2` | Registered entry in Open Board Registry |
| **Microcontroller** | `ESP32S2` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver ... | <start_of_turn>user
I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY suppor... | sensebox_mcu_esp32s2 | ESP32S2 | senseBox | 327,680 | 4,194,304 |
pyintel_hw_cot_002562 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **STM32F401CE (96k RAM. 512k Flash)**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) ... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | genericSTM32F401CE | STM32F401CEU6 | Generic | 98,304 | 524,288 |
pyintel_hw_cot_002563 | native_usb_emulation | I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoi... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Tiny2350**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `pimoroni_tiny2350` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2350` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HID/MIDI/CD... | <start_of_turn>user
I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting... | pimoroni_tiny2350 | RP2350 | Pimoroni | 524,288 | 4,194,304 |
pyintel_hw_cot_002564 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 120 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **NiceMCU XH-WB3S**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `xh-wb3s` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `BK7238` | Native dual-core/accelerated processing |
| **Operating Frequency** | 120 MHz | Sufficient throughput... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 120 KB of unfragmented dynamic heap (accounting f... | xh-wb3s | BK7238 | SparkleIoT | 262,144 | 1,083,136 |
pyintel_hw_cot_002565 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 f... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 1000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (24V). Requires wide DC input step-down regulator or autom... | ### Recommended Board: **OLIMEX ESP32-DevKit-LiPo**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `esp32-devkitlipo` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, bluetooth, ethernet, c... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling ca... | esp32-devkitlipo | ESP32 | OLIMEX | 327,680 | 4,194,304 |
pyintel_hw_cot_002566 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **RP2040 DevKit**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `upesy_rp2040_devkit` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** | 133 MHz | Complet... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | upesy_rp2040_devkit | RP2040 | uPesy | 262,144 | 2,097,152 |
pyintel_hw_cot_002567 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 104 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **ESP32 FM DevKit**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `fm-devkit` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient throughpu... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 104 KB of unfragmented dynamic heap (accounting f... | fm-devkit | ESP32 | Unknown | 327,680 | 4,194,304 |
pyintel_hw_cot_002568 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 172 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **ODROID-GO**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `odroid_esp32` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient throughput f... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 172 KB of unfragmented dynamic heap (accounting f... | odroid_esp32 | ESP32 | Hardkernel | 327,680 | 16,777,216 |
pyintel_hw_cot_002569 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 164 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Makerdiary nRF52840-MDK**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `nrf52840_mdk` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `NRF52840` | Native dual-core/accelerated processing |
| **Operating Frequency** | 64 MHz | Suffici... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 164 KB of unfragmented dynamic heap (accounting f... | nrf52840_mdk | NRF52840 | Makerdiary | 262,144 | 1,048,576 |
pyintel_hw_cot_002570 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 48.0 kHz 16-bit mono produces $48.0 \times 10^3 \times 2 \approx 96,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 1024-point buffer represents $T_{window} = 1024 / (48.0 \times 10^3) \approx 21.33 \text{ ms}$.
- **Processin... | ### Recommended Board: **W5500-EVB-Pico2**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `wiznet_5500_evb_pico2` | Verified Open Board Registry entry |
| **Processor Core** | `RP2350` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 150 MHz | FFT computes in $< 2 \text{ ms}$ (... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | wiznet_5500_evb_pico2 | RP2350 | WIZnet | 524,288 | 2,097,152 |
pyintel_hw_cot_002571 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 44.1 kHz 16-bit mono produces $44.1 \times 10^3 \times 2 \approx 88,200 \text{ bytes/sec}$.
- **FFT Window Duration**: A 2048-point buffer represents $T_{window} = 2048 / (44.1 \times 10^3) \approx 46.44 \text{ ms}$.
- **Processin... | ### Recommended Board: **ST Nucleo F439ZI**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `nucleo_f439zi` | Verified Open Board Registry entry |
| **Processor Core** | `STM32F439ZIT6` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 180 MHz | FFT computes in $< 2 \text{ ms}$ (... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | nucleo_f439zi | STM32F439ZIT6 | ST | 196,608 | 2,097,152 |
pyintel_hw_cot_002572 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 364 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **Akana R1**
| Constraint Parameter | Required Budget | Board Capability (`akana_r1`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 32 KB | Supported with substantial overhead |
| **Total SRAM ... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 364 KB of conti... | akana_r1 | RP2040 | METE HOCA | 262,144 | 16,777,216 |
pyintel_hw_cot_002573 | native_usb_emulation | I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoi... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Adafruit QT Py ESP32-S3 (4M Flash 2M PSRAM)**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `adafruit_qtpy_esp32s3_n4r2` | Registered entry in Open Board Registry |
| **Microcontroller** | `ESP32S3` | Direct native USB 2.0 FS silicon |
| **USB Stack** |... | <start_of_turn>user
I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting... | adafruit_qtpy_esp32s3_n4r2 | ESP32S3 | Adafruit | 327,680 | 4,194,304 |
pyintel_hw_cot_002574 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 40 kHz PWM, each control cycle is $T = 1 / 40\text{ kHz} = 25.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **FlyBoard2040Core**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `flyboard2040_core` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** | 133 MHz | Comple... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | flyboard2040_core | RP2040 | DeRuiLab | 262,144 | 4,194,304 |
pyintel_hw_cot_002575 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 48.0 kHz 16-bit mono produces $48.0 \times 10^3 \times 2 \approx 96,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 2048-point buffer represents $T_{window} = 2048 / (48.0 \times 10^3) \approx 42.67 \text{ ms}$.
- **Processin... | ### Recommended Board: **STM32F446RC (128k RAM. 256k Flash)**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `genericSTM32F446RC` | Verified Open Board Registry entry |
| **Processor Core** | `STM32F446RCT6` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 180 MHz | FFT compute... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | genericSTM32F446RC | STM32F446RCT6 | Generic | 131,072 | 262,144 |
pyintel_hw_cot_002576 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 96.0 kHz 16-bit mono produces $96.0 \times 10^3 \times 2 \approx 192,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 1024-point buffer represents $T_{window} = 1024 / (96.0 \times 10^3) \approx 10.67 \text{ ms}$.
- **Processi... | ### Recommended Board: **Generic - BK7238**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `generic-bk7238` | Verified Open Board Registry entry |
| **Processor Core** | `BK7238` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 120 MHz | FFT computes in $< 2 \text{ ms}$ (well b... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | generic-bk7238 | BK7238 | Generic | 262,144 | 1,083,136 |
pyintel_hw_cot_002577 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 132 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Heltec Wireless Stick Lite**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `heltec_wireless_stick_lite` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 24... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 132 KB of unfragmented dynamic heap (accounting f... | heltec_wireless_stick_lite | ESP32 | Heltec Automation | 327,680 | 4,194,304 |
pyintel_hw_cot_002578 | native_usb_emulation | I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoi... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **WEMOS LOLIN S3 Mini**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `lolin_s3_mini` | Registered entry in Open Board Registry |
| **Microcontroller** | `ESP32S3` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HID... | <start_of_turn>user
I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting... | lolin_s3_mini | ESP32S3 | WEMOS | 327,680 | 4,194,304 |
pyintel_hw_cot_002579 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 fr... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 500 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (12V). Requires wide DC input step-down regulator or automo... | ### Recommended Board: **uPesy ESP32 Wrover DevKit**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `upesy_wrover` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, bluetooth, ethernet, can ... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling cap... | upesy_wrover | ESP32 | uPesy | 327,680 | 4,194,304 |
pyintel_hw_cot_002580 | native_usb_emulation | I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoin... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Adafruit ItsyBitsy 5V/16MHz**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `itsybitsy32u4_5V` | Registered entry in Open Board Registry |
| **Microcontroller** | `ATMEGA32U4` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Drive... | <start_of_turn>user
I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting ... | itsybitsy32u4_5V | ATMEGA32U4 | Adafruit | 2,560 | 28,672 |
pyintel_hw_cot_002581 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **STM32F407IG (192k RAM. 1024k Flash)**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | genericSTM32F407IGT6 | STM32F407IGT6 | Generic | 131,072 | 1,048,576 |
pyintel_hw_cot_002582 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 208 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 240 pixels width $\times$ 240 pixels height = 57,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $240 \times 240 \times 2 = 115,200 \text{ bytes} = 112 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **Raspberry Pi 1 Model B**
| Constraint Parameter | Required Budget | Board Capability (`raspberrypi_1b`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 112 KB (240x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 64 KB | Supported with substantial overhe... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 208 KB of conti... | raspberrypi_1b | BCM2835 | Raspberry Pi | 536,870,912 | 536,870,912 |
pyintel_hw_cot_002583 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **MGBOT IOTIK 32A**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Controll... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | mgbot-iotik32a | ESP32 | MGBOT | 327,680 | 4,194,304 |
pyintel_hw_cot_002584 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 140 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Adafruit Metro ESP32-S2**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `adafruit_metro_esp32s2` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32S2` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 140 KB of unfragmented dynamic heap (accounting f... | adafruit_metro_esp32s2 | ESP32S2 | Adafruit | 327,680 | 4,194,304 |
pyintel_hw_cot_002585 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 40 kHz PWM, each control cycle is $T = 1 / 40\text{ kHz} = 25.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **MKS THR36**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `mksthr36` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** | 133 MHz | Completes FOC loop in ... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | mksthr36 | RP2040 | Makerbase | 262,144 | 1,048,576 |
pyintel_hw_cot_002586 | native_usb_emulation | I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable en... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Feather RP2040 Prop-Maker**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `adafruit_feather_prop_maker` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2040` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native ... | <start_of_turn>user
I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY suppor... | adafruit_feather_prop_maker | RP2040 | Adafruit | 262,144 | 8,388,608 |
pyintel_hw_cot_002587 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S doub... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 96.0 kHz 16-bit mono produces $96.0 \times 10^3 \times 2 \approx 192,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 512-point buffer represents $T_{window} = 512 / (96.0 \times 10^3) \approx 5.33 \text{ ms}$.
- **Processing ... | ### Recommended Board: **WR2LE Wi-Fi Module**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `wr2le` | Verified Open Board Registry entry |
| **Processor Core** | `RTL8710BX` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 62.5 MHz | FFT computes in $< 2 \text{ ms}$ (well belo... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support c... | wr2le | RTL8710BX | Tuya Inc. | 262,144 | 806,912 |
pyintel_hw_cot_002588 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 108 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Espressif ESP-WROVER-KIT**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `esp-wrover-kit` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Suffic... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 108 KB of unfragmented dynamic heap (accounting f... | esp-wrover-kit | ESP32 | Espressif | 327,680 | 4,194,304 |
pyintel_hw_cot_002589 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 40 kHz PWM, each control cycle is $T = 1 / 40\text{ kHz} = 25.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **STM32F423CH (320k RAM. 1536k Flash)**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `genericSTM32F423CH` | Verified Open Board Registry entry |
| **MCU Core** | `STM32F423CHU6` | High-speed real-time core with hardware math |
| **Core... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | genericSTM32F423CH | STM32F423CHU6 | Generic | 327,680 | 1,572,864 |
pyintel_hw_cot_002590 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 48.0 kHz 16-bit mono produces $48.0 \times 10^3 \times 2 \approx 96,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 1024-point buffer represents $T_{window} = 1024 / (48.0 \times 10^3) \approx 21.33 \text{ ms}$.
- **Processin... | ### Recommended Board: **Quectel EC100Y LTE Cat.1 Module**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `ec100y` | Verified Open Board Registry entry |
| **Processor Core** | `ASR1601` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 416 MHz | FFT computes in $< 2 \text{ ms}$... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | ec100y | ASR1601 | Quectel Wireless Solutions Co., Ltd. | 524,288 | 1,048,576 |
pyintel_hw_cot_002591 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S doub... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 48.0 kHz 16-bit mono produces $48.0 \times 10^3 \times 2 \approx 96,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 512-point buffer represents $T_{window} = 512 / (48.0 \times 10^3) \approx 10.67 \text{ ms}$.
- **Processing ... | ### Recommended Board: **AFW121T**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `afw121t` | Verified Open Board Registry entry |
| **Processor Core** | `RTL8710BX` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 62.5 MHz | FFT computes in $< 2 \text{ ms}$ (well below 10.7 ms... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support c... | afw121t | RTL8710BX | 99iot(Shenzhen)co.,ltd | 262,144 | 479,232 |
pyintel_hw_cot_002592 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 44.1 kHz 16-bit mono produces $44.1 \times 10^3 \times 2 \approx 88,200 \text{ bytes/sec}$.
- **FFT Window Duration**: A 1024-point buffer represents $T_{window} = 1024 / (44.1 \times 10^3) \approx 23.22 \text{ ms}$.
- **Processin... | ### Recommended Board: **AI-Thinker A9G GSM Module**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `a9g` | Verified Open Board Registry entry |
| **Processor Core** | `RDA8955` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 178 MHz | FFT computes in $< 2 \text{ ms}$ (well be... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | a9g | RDA8955 | Ai-Thinker Co., Ltd. | 1,040,384 | 589,824 |
pyintel_hw_cot_002593 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 144 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Valetron Systems VALTRACK-V4MVF**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `valtrack_v4_mfw_esp32_c3` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32C3` | Native dual-core/accelerated processing |
| **Operating Frequency**... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 144 KB of unfragmented dynamic heap (accounting f... | valtrack_v4_mfw_esp32_c3 | ESP32C3 | Valetron Systems | 327,680 | 4,194,304 |
pyintel_hw_cot_002594 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 25 kHz PWM, each control cycle is $T = 1 / 25\text{ kHz} = 40.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Athera Motion Core**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `athera_motion_core` | Verified Open Board Registry entry |
| **MCU Core** | `RP2350` | High-speed real-time core with hardware math |
| **Core Clock** | 150 MHz | Com... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | athera_motion_core | RP2350 | Pyintel / Athera Controls | 524,288 | 16,777,216 |
pyintel_hw_cot_002595 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 140 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Espressif ESP32-C3-DevKitM-1**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `esp32-c3-devkitm-1` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32C3` | Native dual-core/accelerated processing |
| **Operating Frequency** | 160 MH... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 140 KB of unfragmented dynamic heap (accounting f... | esp32-c3-devkitm-1 | ESP32C3 | Espressif | 327,680 | 4,194,304 |
pyintel_hw_cot_002596 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **ST B-U585I-IOT02A Discovery**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `disco_b_u585i_iot02a` | Verified Open Board Registry entry |
| **MCU Core** | `STM32U585AII6Q` | High-speed real-time core with hardware math |
| **Core Cloc... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | disco_b_u585i_iot02a | STM32U585AII6Q | ST | 262,144 | 2,097,152 |
pyintel_hw_cot_002597 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Challenger 2040 UWB**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `challenger_2040_uwb` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** | 133 MHz | C... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | challenger_2040_uwb | RP2040 | iLabs | 262,144 | 8,388,608 |
pyintel_hw_cot_002598 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 136 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **EspinalLab ATMegaZero ESP32-S2**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `atmegazero_esp32s2` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32S2` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 ... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 136 KB of unfragmented dynamic heap (accounting f... | atmegazero_esp32s2 | ESP32S2 | EspinalLab | 327,680 | 16,777,216 |
pyintel_hw_cot_002599 | native_usb_emulation | I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable en... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Arduino Tian**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `tian` | Registered entry in Open Board Registry |
| **Microcontroller** | `SAMD21G18A` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HID/MIDI/CDC des... | <start_of_turn>user
I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY suppor... | tian | SAMD21G18A | Arduino | 32,768 | 262,144 |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.