id large_stringlengths 21 21 | domain large_stringclasses 7
values | instruction large_stringclasses 115
values | reasoning large_stringlengths 1.07k 5.05k | response large_stringlengths 677 1.11k | text large_stringlengths 2.31k 6.39k | target_board_id large_stringclasses 863
values | mcu large_stringclasses 201
values | vendor large_stringclasses 231
values | ram_bytes int64 2.05k 8.59B | rom_bytes int64 0 1.07B |
|---|---|---|---|---|---|---|---|---|---|---|
pyintel_hw_cot_002900 | native_usb_emulation | I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoi... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Shake RP2040**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `melopero_shake_rp2040` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2040` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HID... | <start_of_turn>user
I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting... | melopero_shake_rp2040 | RP2040 | Melopero | 262,144 | 16,777,216 |
pyintel_hw_cot_002901 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 25 kHz PWM, each control cycle is $T = 1 / 25\text{ kHz} = 40.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Cookie RP2040**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `melopero_cookie_rp2040` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** | 133 MHz | Comp... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | melopero_cookie_rp2040 | RP2040 | Melopero | 262,144 | 8,388,608 |
pyintel_hw_cot_002902 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capab... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 2000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (7V–28V DC wide input). Requires wide DC input step-down r... | ### Recommended Board: **Black STM32F407ZG**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `black_f407zg` | Registered open-hardware entry |
| **MCU Architecture** | `STM32F407ZGT6` | High-speed real-time core |
| **CAN Bus Interface** | can | Hardware frame filtration... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient inte... | black_f407zg | STM32F407ZGT6 | ST | 131,072 | 1,048,576 |
pyintel_hw_cot_002903 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 96 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 KB... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **T1-2S Wi-Fi Module**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `t1-2s` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `BK7238` | Native dual-core/accelerated processing |
| **Operating Frequency** | 120 MHz | Sufficient throughpu... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 96 KB of unfragmented dynamic heap (accounting fo... | t1-2s | BK7238 | Tuya Inc. | 262,144 | 1,083,136 |
pyintel_hw_cot_002904 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 164 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **WBR1 Wi-Fi Module**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `wbr1` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `RTL8720CF` | Native dual-core/accelerated processing |
| **Operating Frequency** | 100 MHz | Sufficient throughp... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 164 KB of unfragmented dynamic heap (accounting f... | wbr1 | RTL8720CF | Tuya Inc. | 262,144 | 917,504 |
pyintel_hw_cot_002905 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 140 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Adafruit CLUE nRF52840**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `adafruit_clue_nrf52840` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `NRF52840` | Native dual-core/accelerated processing |
| **Operating Frequency** | 64 MHz ... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 140 KB of unfragmented dynamic heap (accounting f... | adafruit_clue_nrf52840 | NRF52840 | Adafruit | 248,832 | 815,104 |
pyintel_hw_cot_002906 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 240 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 240 pixels width $\times$ 240 pixels height = 57,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $240 \times 240 \times 2 = 115,200 \text{ bytes} = 112 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **IDM2040-7A**
| Constraint Parameter | Required Budget | Board Capability (`bridgetek_idm2040_7a`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 112 KB (240x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 96 KB | Supported with substantial overhead |
|... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 240 KB of conti... | bridgetek_idm2040_7a | RP2040 | BridgeTek | 262,144 | 8,388,608 |
pyintel_hw_cot_002907 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 246 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 320 pixels width $\times$ 240 pixels height = 76,800 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $320 \times 240 \times 2 = 153,600 \text{ bytes} = 150 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **Pico**
| Constraint Parameter | Required Budget | Board Capability (`rpipico`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 150 KB (320x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 64 KB | Supported with substantial overhead |
| **Total SRAM Avail... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 246 KB of conti... | rpipico | RP2040 | Raspberry Pi | 262,144 | 2,097,152 |
pyintel_hw_cot_002908 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 396 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **STM32F413RG (320k RAM. 1024k Flash)**
| Constraint Parameter | Required Budget | Board Capability (`genericSTM32F413RG`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 64 KB | Supported with s... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 396 KB of conti... | genericSTM32F413RG | STM32F413RGT6 | Generic | 327,680 | 1,048,576 |
pyintel_hw_cot_002909 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 208 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 240 pixels width $\times$ 240 pixels height = 57,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $240 \times 240 \times 2 = 115,200 \text{ bytes} = 112 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **MH ET LIVE ESP32MiniKit**
| Constraint Parameter | Required Budget | Board Capability (`mhetesp32minikit`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 112 KB (240x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 64 KB | Supported with substantial ove... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 208 KB of conti... | mhetesp32minikit | ESP32 | MH-ET Live | 327,680 | 4,194,304 |
pyintel_hw_cot_002910 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 128 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **32F723EDISCOVERY**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `disco_f723ie` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `STM32F723IEK6` | Native dual-core/accelerated processing |
| **Operating Frequency** | 216 MHz | Sufficie... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 128 KB of unfragmented dynamic heap (accounting f... | disco_f723ie | STM32F723IEK6 | ST | 196,608 | 524,288 |
pyintel_hw_cot_002911 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 164 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Smart Bee Data Logger**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `bee_data_logger` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32S3` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Suffic... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 164 KB of unfragmented dynamic heap (accounting f... | bee_data_logger | ESP32S3 | Smart Bee | 327,680 | 8,388,608 |
pyintel_hw_cot_002912 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 f... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 2000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (12V). Requires wide DC input step-down regulator or autom... | ### Recommended Board: **Heltec WiFi LoRa 32**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `heltec_wifi_lora_32` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, bluetooth, ethernet, can... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling ca... | heltec_wifi_lora_32 | ESP32 | Heltec Automation | 327,680 | 4,194,304 |
pyintel_hw_cot_002913 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S doub... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 96.0 kHz 16-bit mono produces $96.0 \times 10^3 \times 2 \approx 192,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 512-point buffer represents $T_{window} = 512 / (96.0 \times 10^3) \approx 5.33 \text{ ms}$.
- **Processing ... | ### Recommended Board: **Servo2040**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `pimoroni_servo2040` | Verified Open Board Registry entry |
| **Processor Core** | `RP2040` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 133 MHz | FFT computes in $< 2 \text{ ms}$ (well belo... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support c... | pimoroni_servo2040 | RP2040 | Pimoroni | 262,144 | 2,097,152 |
pyintel_hw_cot_002914 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 25 kHz PWM, each control cycle is $T = 1 / 25\text{ kHz} = 40.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Challenger 2040 UWB**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `challenger_2040_uwb` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** | 133 MHz | C... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | challenger_2040_uwb | RP2040 | iLabs | 262,144 | 8,388,608 |
pyintel_hw_cot_002915 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 25 kHz PWM, each control cycle is $T = 1 / 25\text{ kHz} = 40.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Tiny2350**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `pimoroni_tiny2350` | Verified Open Board Registry entry |
| **MCU Core** | `RP2350` | High-speed real-time core with hardware math |
| **Core Clock** | 150 MHz | Completes FOC ... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | pimoroni_tiny2350 | RP2350 | Pimoroni | 524,288 | 4,194,304 |
pyintel_hw_cot_002916 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S doub... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 48.0 kHz 16-bit mono produces $48.0 \times 10^3 \times 2 \approx 96,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 512-point buffer represents $T_{window} = 512 / (48.0 \times 10^3) \approx 10.67 \text{ ms}$.
- **Processing ... | ### Recommended Board: **ESP32-S3 PowerFeather**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `esp32s3_powerfeather` | Verified Open Board Registry entry |
| **Processor Core** | `ESP32S3` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 240 MHz | FFT computes in $< 2 \text{ ... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support c... | esp32s3_powerfeather | ESP32S3 | PowerFeather | 327,680 | 8,388,608 |
pyintel_hw_cot_002917 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 96 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 KB... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Maxim Health Sensor Platform**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `max32620hsp` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `MAX32620` | Native dual-core/accelerated processing |
| **Operating Frequency** | 96 MHz | Suf... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 96 KB of unfragmented dynamic heap (accounting fo... | max32620hsp | MAX32620 | Maxim | 262,144 | 2,097,152 |
pyintel_hw_cot_002918 | native_usb_emulation | I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoin... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Arduino Esplora**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `esplora` | Registered entry in Open Board Registry |
| **Microcontroller** | `ATMEGA32U4` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HID/MIDI/C... | <start_of_turn>user
I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting ... | esplora | ATMEGA32U4 | Arduino | 2,560 | 28,672 |
pyintel_hw_cot_002919 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 164 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Adafruit Qualia ESP32-S3 RGB666**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `adafruit_qualia_s3_rgb666` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32S3` | Native dual-core/accelerated processing |
| **Operating Frequency*... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 164 KB of unfragmented dynamic heap (accounting f... | adafruit_qualia_s3_rgb666 | ESP32S3 | Adafruit | 327,680 | 16,777,216 |
pyintel_hw_cot_002920 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **STEVAL-FCU001V1 Flight controller unit evaluation board**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackb... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | steval_fcu001v1 | STM32F401CCU6 | ST | 65,536 | 262,144 |
pyintel_hw_cot_002921 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **PicoADK**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Controller** | H... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | datanoisetv_picoadk | RP2040 | DatanoiseTV | 262,144 | 2,097,152 |
pyintel_hw_cot_002922 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 25 kHz PWM, each control cycle is $T = 1 / 25\text{ kHz} = 40.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **MultiTech mDot**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `mts_mdot_f405rg` | Verified Open Board Registry entry |
| **MCU Core** | `STM32F411RET6` | High-speed real-time core with hardware math |
| **Core Clock** | 100 MHz | Com... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | mts_mdot_f405rg | STM32F411RET6 | MultiTech | 131,072 | 524,288 |
pyintel_hw_cot_002923 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 f... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 2000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (24V). Requires wide DC input step-down regulator or autom... | ### Recommended Board: **Pycom GPy**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `pycom_gpy` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, bluetooth, ethernet, can | Hardware frame fi... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling ca... | pycom_gpy | ESP32 | Pycom Ltd. | 327,680 | 4,194,304 |
pyintel_hw_cot_002924 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 396 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **Pycom GPy**
| Constraint Parameter | Required Budget | Board Capability (`pycom_gpy`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 64 KB | Supported with substantial overhead |
| **Total SRA... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 396 KB of conti... | pycom_gpy | ESP32 | Pycom Ltd. | 327,680 | 4,194,304 |
pyintel_hw_cot_002925 | native_usb_emulation | I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoi... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **DFRobot Firebeetle 2 ESP32-S3**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `dfrobot_firebeetle2_esp32s3` | Registered entry in Open Board Registry |
| **Microcontroller** | `ESP32S3` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Na... | <start_of_turn>user
I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting... | dfrobot_firebeetle2_esp32s3 | ESP32S3 | DFRobot | 327,680 | 4,194,304 |
pyintel_hw_cot_002926 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 48.0 kHz 16-bit mono produces $48.0 \times 10^3 \times 2 \approx 96,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 2048-point buffer represents $T_{window} = 2048 / (48.0 \times 10^3) \approx 42.67 \text{ ms}$.
- **Processin... | ### Recommended Board: **WR2 Wi-Fi Module**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `wr2` | Verified Open Board Registry entry |
| **Processor Core** | `RTL8710BN` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 125 MHz | FFT computes in $< 2 \text{ ms}$ (well below 42.... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | wr2 | RTL8710BN | Tuya Inc. | 262,144 | 806,912 |
pyintel_hw_cot_002927 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **RPICO32**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `ilabs_rpico32` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** | 133 MHz | Completes FOC loop ... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | ilabs_rpico32 | RP2040 | iLabs | 262,144 | 8,388,608 |
pyintel_hw_cot_002928 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 136 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Trueverit ESP32 Universal IoT Driver MK II**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `trueverit-iot-driver-mk2` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Fr... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 136 KB of unfragmented dynamic heap (accounting f... | trueverit-iot-driver-mk2 | ESP32 | Trueverit | 327,680 | 4,194,304 |
pyintel_hw_cot_002929 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capab... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 1000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (7V–28V DC wide input). Requires wide DC input step-down r... | ### Recommended Board: **ST 32F469IDISCOVERY**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `disco_f469ni` | Registered open-hardware entry |
| **MCU Architecture** | `STM32F469NIH6` | High-speed real-time core |
| **CAN Bus Interface** | can | Hardware frame filtrati... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient inte... | disco_f469ni | STM32F469NIH6 | ST | 393,216 | 2,097,152 |
pyintel_hw_cot_002930 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capab... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 1000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (7V–28V DC wide input). Requires wide DC input step-down r... | ### Recommended Board: **ST Nucleo F042K6**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `nucleo_f042k6` | Registered open-hardware entry |
| **MCU Architecture** | `STM32F042K6T6` | High-speed real-time core |
| **CAN Bus Interface** | can | Hardware frame filtration... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient inte... | nucleo_f042k6 | STM32F042K6T6 | ST | 6,144 | 32,768 |
pyintel_hw_cot_002931 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 96.0 kHz 16-bit mono produces $96.0 \times 10^3 \times 2 \approx 192,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 2048-point buffer represents $T_{window} = 2048 / (96.0 \times 10^3) \approx 21.33 \text{ ms}$.
- **Processi... | ### Recommended Board: **Fishino Piranha ESP-32**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `piranha_esp32` | Verified Open Board Registry entry |
| **Processor Core** | `ESP32` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 240 MHz | FFT computes in $< 2 \text{ ms}$ (we... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | piranha_esp32 | ESP32 | Fishino | 327,680 | 4,194,304 |
pyintel_hw_cot_002932 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 148 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Arduino Giga R1 (M7 core)**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `giga_r1_m7` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `STM32H747XIH6` | Native dual-core/accelerated processing |
| **Operating Frequency** | 480 MHz | S... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 148 KB of unfragmented dynamic heap (accounting f... | giga_r1_m7 | STM32H747XIH6 | Arduino | 523,624 | 786,432 |
pyintel_hw_cot_002933 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 140 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **WR1E Wi-Fi Module**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `wr1e` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `RTL8710BN` | Native dual-core/accelerated processing |
| **Operating Frequency** | 125 MHz | Sufficient throughp... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 140 KB of unfragmented dynamic heap (accounting f... | wr1e | RTL8710BN | Tuya Inc. | 262,144 | 806,912 |
pyintel_hw_cot_002934 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 96.0 kHz 16-bit mono produces $96.0 \times 10^3 \times 2 \approx 192,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 2048-point buffer represents $T_{window} = 2048 / (96.0 \times 10^3) \approx 21.33 \text{ ms}$.
- **Processi... | ### Recommended Board: **u-blox C030-U201 IoT Starter Kit**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `ublox_c030_u201` | Verified Open Board Registry entry |
| **Processor Core** | `STM32F437VG` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 180 MHz | FFT computes in $<... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | ublox_c030_u201 | STM32F437VG | u-blox | 262,144 | 1,048,576 |
pyintel_hw_cot_002935 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 40 kHz PWM, each control cycle is $T = 1 / 40\text{ kHz} = 25.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Suibo RP2040**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `degz_suibo` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** | 133 MHz | Completes FOC loo... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | degz_suibo | RP2040 | Degz Robotics | 262,144 | 16,777,216 |
pyintel_hw_cot_002936 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 156 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Franzininho WiFi MSC**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `franzininho_wifi_msc_esp32s2` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32S2` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 ... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 156 KB of unfragmented dynamic heap (accounting f... | franzininho_wifi_msc_esp32s2 | ESP32S2 | Franzininho | 327,680 | 4,194,304 |
pyintel_hw_cot_002937 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 188 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **ETBoard**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `etboard` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient throughput for TLS ... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 188 KB of unfragmented dynamic heap (accounting f... | etboard | ESP32 | ETBoard | 327,680 | 4,194,304 |
pyintel_hw_cot_002938 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S doub... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 44.1 kHz 16-bit mono produces $44.1 \times 10^3 \times 2 \approx 88,200 \text{ bytes/sec}$.
- **FFT Window Duration**: A 512-point buffer represents $T_{window} = 512 / (44.1 \times 10^3) \approx 11.61 \text{ ms}$.
- **Processing ... | ### Recommended Board: **ItsyBitsy RP2040**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `adafruit_itsybitsy` | Verified Open Board Registry entry |
| **Processor Core** | `RP2040` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 133 MHz | FFT computes in $< 2 \text{ ms}$ (we... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support c... | adafruit_itsybitsy | RP2040 | Adafruit | 262,144 | 8,388,608 |
pyintel_hw_cot_002939 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 48.0 kHz 16-bit mono produces $48.0 \times 10^3 \times 2 \approx 96,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 1024-point buffer represents $T_{window} = 1024 / (48.0 \times 10^3) \approx 21.33 \text{ ms}$.
- **Processin... | ### Recommended Board: **WeAct Studio BlackPill V2.0 (STM32F401CC)**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `blackpill_f401cc` | Verified Open Board Registry entry |
| **Processor Core** | `STM32F401CCU6` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 84 MHz | FFT com... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | blackpill_f401cc | STM32F401CCU6 | WeAct Studio | 65,536 | 262,144 |
pyintel_hw_cot_002940 | native_usb_emulation | I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoin... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Arduino Industrial 101**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `chiwawa` | Registered entry in Open Board Registry |
| **Microcontroller** | `ATMEGA32U4` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HID... | <start_of_turn>user
I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting ... | chiwawa | ATMEGA32U4 | Arduino | 2,560 | 28,672 |
pyintel_hw_cot_002941 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 364 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **Quectel EG915U LTE Cat.1 Module**
| Constraint Parameter | Required Budget | Board Capability (`eg915u`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 32 KB | Supported with substantial overh... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 364 KB of conti... | eg915u | RDA8910 | Quectel Wireless Solutions Co., Ltd. | 524,288 | 1,048,576 |
pyintel_hw_cot_002942 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capab... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 2000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (7V–28V DC wide input). Requires wide DC input step-down r... | ### Recommended Board: **Microsoft Azure IoT Development Kit (MXChip AZ3166)**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `mxchip_az3166` | Registered open-hardware entry |
| **MCU Architecture** | `STM32F412ZGT6` | High-speed real-time core |
| **CAN Bus Interface*... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient inte... | mxchip_az3166 | STM32F412ZGT6 | MXChip | 262,144 | 1,048,576 |
pyintel_hw_cot_002943 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S doub... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 44.1 kHz 16-bit mono produces $44.1 \times 10^3 \times 2 \approx 88,200 \text{ bytes/sec}$.
- **FFT Window Duration**: A 512-point buffer represents $T_{window} = 512 / (44.1 \times 10^3) \approx 11.61 \text{ ms}$.
- **Processing ... | ### Recommended Board: **STM32F413RG (320k RAM. 1024k Flash)**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `genericSTM32F413RG` | Verified Open Board Registry entry |
| **Processor Core** | `STM32F413RGT6` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 100 MHz | FFT comput... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support c... | genericSTM32F413RG | STM32F413RGT6 | Generic | 327,680 | 1,048,576 |
pyintel_hw_cot_002944 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 172 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **SparkFun ESP32 IoT RedBoard**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `sparkfun_esp32_iot_redboard` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | ... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 172 KB of unfragmented dynamic heap (accounting f... | sparkfun_esp32_iot_redboard | ESP32 | SparkFun | 327,680 | 4,194,304 |
pyintel_hw_cot_002945 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **Deneyap Mini**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Controller*... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | deneyapmini | ESP32S2 | T3 Foundation | 327,680 | 4,194,304 |
pyintel_hw_cot_002946 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 f... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 2000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (12V). Requires wide DC input step-down regulator or autom... | ### Recommended Board: **Adafruit Feather ESP32-S3 2MB PSRAM**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `adafruit_feather_esp32s3` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32S3` | High-speed real-time core |
| **CAN Bus Interface** | bluetoo... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling ca... | adafruit_feather_esp32s3 | ESP32S3 | Adafruit | 327,680 | 4,194,304 |
pyintel_hw_cot_002947 | native_usb_emulation | I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoin... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Espressif ESP32-S3-DevKitM-1**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `esp32-s3-devkitm-1` | Registered entry in Open Board Registry |
| **Microcontroller** | `ESP32S3` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Drive... | <start_of_turn>user
I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting ... | esp32-s3-devkitm-1 | ESP32S3 | Espressif | 327,680 | 8,388,608 |
pyintel_hw_cot_002948 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 396 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **TTGO T-OI PLUS RISC-V ESP32-C3**
| Constraint Parameter | Required Budget | Board Capability (`ttgo-t-oi-plus`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 64 KB | Supported with substantia... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 396 KB of conti... | ttgo-t-oi-plus | ESP32C3 | TTGO | 327,680 | 4,194,304 |
pyintel_hw_cot_002949 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 128 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **u-blox NINA-W10 series**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `nina_w10` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient thr... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 128 KB of unfragmented dynamic heap (accounting f... | nina_w10 | ESP32 | u-blox | 327,680 | 2,097,152 |
pyintel_hw_cot_002950 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 208 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 240 pixels width $\times$ 240 pixels height = 57,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $240 \times 240 \times 2 = 115,200 \text{ bytes} = 112 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **NiceMCU XH-WB3S**
| Constraint Parameter | Required Budget | Board Capability (`xh-wb3s`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 112 KB (240x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 64 KB | Supported with substantial overhead |
| **Total... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 208 KB of conti... | xh-wb3s | BK7238 | SparkleIoT | 262,144 | 1,083,136 |
pyintel_hw_cot_002951 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 240 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 240 pixels width $\times$ 240 pixels height = 57,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $240 \times 240 \times 2 = 115,200 \text{ bytes} = 112 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **RP2040**
| Constraint Parameter | Required Budget | Board Capability (`generic`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 112 KB (240x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 96 KB | Supported with substantial overhead |
| **Total SRAM Ava... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 240 KB of conti... | generic | RP2040 | Generic | 262,144 | 16,777,216 |
pyintel_hw_cot_002952 | native_usb_emulation | I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable en... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **WEMOS LOLIN S2 PICO**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `lolin_s2_pico` | Registered entry in Open Board Registry |
| **Microcontroller** | `ESP32S2` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HID... | <start_of_turn>user
I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY suppor... | lolin_s2_pico | ESP32S2 | WEMOS | 327,680 | 4,194,304 |
pyintel_hw_cot_002953 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 214 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 320 pixels width $\times$ 240 pixels height = 76,800 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $320 \times 240 \times 2 = 153,600 \text{ bytes} = 150 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **ALKS ESP32**
| Constraint Parameter | Required Budget | Board Capability (`alksesp32`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 150 KB (320x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 32 KB | Supported with substantial overhead |
| **Total SR... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 214 KB of conti... | alksesp32 | ESP32 | RoboticsBrno | 327,680 | 4,194,304 |
pyintel_hw_cot_002954 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 f... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 2000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (24V). Requires wide DC input step-down regulator or autom... | ### Recommended Board: **ST 32F746GDISCOVERY**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `disco_f746ng` | Registered open-hardware entry |
| **MCU Architecture** | `STM32F746NGH6` | High-speed real-time core |
| **CAN Bus Interface** | can, ethernet | Hardware fram... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling ca... | disco_f746ng | STM32F746NGH6 | ST | 327,680 | 1,048,576 |
pyintel_hw_cot_002955 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **Helios**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Controller** | Ha... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | 0xcb_helios | RP2040 | 0xCB | 262,144 | 16,777,216 |
pyintel_hw_cot_002956 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **Plasma2350W**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Controller**... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | pimoroni_plasma2350w | RP2350 | Pimoroni | 524,288 | 2,097,152 |
pyintel_hw_cot_002957 | native_usb_emulation | I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoi... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Espressif ESP32-S3-DevKitC-1-N8 (8 MB QD, No PSRAM)**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `esp32-s3-devkitc-1` | Registered entry in Open Board Registry |
| **Microcontroller** | `ESP32S3` | Direct native USB 2.0 FS silicon |
| **USB Stack** |... | <start_of_turn>user
I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting... | esp32-s3-devkitc-1 | ESP32S3 | Espressif | 327,680 | 8,388,608 |
pyintel_hw_cot_002958 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 152 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **u-blox ODIN-W2**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `mtb_ublox_odin_w2` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `STM32F439ZIY6` | Native dual-core/accelerated processing |
| **Operating Frequency** | 168 MHz | Suffi... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 152 KB of unfragmented dynamic heap (accounting f... | mtb_ublox_odin_w2 | STM32F439ZIY6 | u-blox | 262,144 | 2,097,152 |
pyintel_hw_cot_002959 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 246 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 320 pixels width $\times$ 240 pixels height = 76,800 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $320 \times 240 \times 2 = 153,600 \text{ bytes} = 150 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **W6300-EVB-Pico2**
| Constraint Parameter | Required Budget | Board Capability (`wiznet_6300_evb_pico2`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 150 KB (320x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 64 KB | Supported with substantial overhe... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 246 KB of conti... | wiznet_6300_evb_pico2 | RP2350 | WIZnet | 524,288 | 2,097,152 |
pyintel_hw_cot_002960 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capab... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 1000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (7V–28V DC wide input). Requires wide DC input step-down r... | ### Recommended Board: **Adafruit Hallowing M4**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `adafruit_hallowing_m4` | Registered open-hardware entry |
| **MCU Architecture** | `SAMD51J19A` | High-speed real-time core |
| **CAN Bus Interface** | | Hardware frame fil... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient inte... | adafruit_hallowing_m4 | SAMD51J19A | Adafruit | 196,608 | 507,904 |
pyintel_hw_cot_002961 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **TAMC Termod S3**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Controlle... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | tamc_termod_s3 | ESP32S3 | TAMC | 327,680 | 8,388,608 |
pyintel_hw_cot_002962 | native_usb_emulation | I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable en... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **W55RP20-EVB-Pico**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `wiznet_55rp20_evb_pico` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2040` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custo... | <start_of_turn>user
I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY suppor... | wiznet_55rp20_evb_pico | RP2040 | WIZnet | 262,144 | 2,097,152 |
pyintel_hw_cot_002963 | native_usb_emulation | I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoin... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **RP2040 LCD 1.28**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `waveshare_rp2040_lcd_1_28` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2040` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Cus... | <start_of_turn>user
I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting ... | waveshare_rp2040_lcd_1_28 | RP2040 | Waveshare | 262,144 | 2,097,152 |
pyintel_hw_cot_002964 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **IoT RedBoard RP2350**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `sparkfun_iotredboard_rp2350` | Verified Open Board Registry entry |
| **MCU Core** | `RP2350` | High-speed real-time core with hardware math |
| **Core Clock** | 150... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | sparkfun_iotredboard_rp2350 | RP2350 | SparkFun | 524,288 | 16,777,216 |
pyintel_hw_cot_002965 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 208 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 240 pixels width $\times$ 240 pixels height = 57,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $240 \times 240 \times 2 = 115,200 \text{ bytes} = 112 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **Plasma2350W**
| Constraint Parameter | Required Budget | Board Capability (`pimoroni_plasma2350w`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 112 KB (240x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 64 KB | Supported with substantial overhead |
... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 208 KB of conti... | pimoroni_plasma2350w | RP2350 | Pimoroni | 524,288 | 2,097,152 |
pyintel_hw_cot_002966 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **VCCGND F103ZET6 Mini**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `vccgnd_f103zet6` | Verified Open Board Registry entry |
| **MCU Core** | `STM32F103ZET6` | High-speed real-time core with hardware math |
| **Core Clock** | 72 MHz ... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | vccgnd_f103zet6 | STM32F103ZET6 | VCCGND | 65,536 | 524,288 |
pyintel_hw_cot_002967 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 25 kHz PWM, each control cycle is $T = 1 / 25\text{ kHz} = 40.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **PicoADK**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `datanoisetv_picoadk` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** | 133 MHz | Completes FOC... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | datanoisetv_picoadk | RP2040 | DatanoiseTV | 262,144 | 2,097,152 |
pyintel_hw_cot_002968 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capabi... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 500 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (7V–28V DC wide input). Requires wide DC input step-down re... | ### Recommended Board: **Unexpected Maker TinyPICO**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `tinypico` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, bluetooth, ethernet, can | Ha... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient inter... | tinypico | ESP32 | Unexpected Maker | 327,680 | 4,194,304 |
pyintel_hw_cot_002969 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **RP2040 Zero**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `waveshare_rp2040_zero` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** | 133 MHz | Complet... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | waveshare_rp2040_zero | RP2040 | Waveshare | 262,144 | 2,097,152 |
pyintel_hw_cot_002970 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 f... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 2000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (12V). Requires wide DC input step-down regulator or autom... | ### Recommended Board: **ST Nucleo H743ZI**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `nucleo_h743zi` | Registered open-hardware entry |
| **MCU Architecture** | `STM32H743ZIT6` | High-speed real-time core |
| **CAN Bus Interface** | can, ethernet | Hardware frame ... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling ca... | nucleo_h743zi | STM32H743ZIT6 | ST | 524,288 | 2,097,152 |
pyintel_hw_cot_002971 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **ST Nucleo L152RE**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `nucleo_l152re` | Verified Open Board Registry entry |
| **MCU Core** | `STM32L152RET6` | High-speed real-time core with hardware math |
| **Core Clock** | 32 MHz | Comp... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | nucleo_l152re | STM32L152RET6 | ST | 81,920 | 524,288 |
pyintel_hw_cot_002972 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **Servo2040**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Controller** |... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | pimoroni_servo2040 | RP2040 | Pimoroni | 262,144 | 2,097,152 |
pyintel_hw_cot_002973 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 278 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 320 pixels width $\times$ 240 pixels height = 76,800 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $320 \times 240 \times 2 = 153,600 \text{ bytes} = 150 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **Adafruit PyPortal M4**
| Constraint Parameter | Required Budget | Board Capability (`adafruit_pyportal_m4`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 150 KB (320x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 96 KB | Supported with substantial ov... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 278 KB of conti... | adafruit_pyportal_m4 | SAMD51J20A | Adafruit | 262,144 | 1,048,576 |
pyintel_hw_cot_002974 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 f... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 1000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (24V). Requires wide DC input step-down regulator or autom... | ### Recommended Board: **Nucleo G491RE**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `nucleo_g491re` | Registered open-hardware entry |
| **MCU Architecture** | `STM32G491RET6` | High-speed real-time core |
| **CAN Bus Interface** | can | Hardware frame filtration & ... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling ca... | nucleo_g491re | STM32G491RET6 | ST | 114,688 | 524,288 |
pyintel_hw_cot_002975 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 148 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Denky D4 (PICO-V3-02)**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `denky_d4` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient thro... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 148 KB of unfragmented dynamic heap (accounting f... | denky_d4 | ESP32 | Denky | 327,680 | 8,388,608 |
pyintel_hw_cot_002976 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Pico2XXL**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `olimex_pico2xxl` | Verified Open Board Registry entry |
| **MCU Core** | `RP2350` | High-speed real-time core with hardware math |
| **Core Clock** | 150 MHz | Completes FOC lo... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | olimex_pico2xxl | RP2350 | Olimex | 524,288 | 16,777,216 |
pyintel_hw_cot_002977 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **STM32F413RH (320k RAM. 1536k Flash)**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | genericSTM32F413RH | STM32F413RHT6 | Generic | 327,680 | 1,572,864 |
pyintel_hw_cot_002978 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 208 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 240 pixels width $\times$ 240 pixels height = 57,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $240 \times 240 \times 2 = 115,200 \text{ bytes} = 112 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **LSC LMA35 BK7231N**
| Constraint Parameter | Required Budget | Board Capability (`lsc-lma35`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 112 KB (240x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 64 KB | Supported with substantial overhead |
| **T... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 208 KB of conti... | lsc-lma35 | BK7231N | Unknown | 262,144 | 1,083,136 |
pyintel_hw_cot_002979 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **3D Printer control board**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `rumba32_f446ve` | Verified Open Board Registry entry |
| **MCU Core** | `STM32F446RET6` | High-speed real-time core with hardware math |
| **Core Clock** | 180 ... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | rumba32_f446ve | STM32F446RET6 | RUMBA | 131,072 | 524,288 |
pyintel_hw_cot_002980 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 124 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **WeAct Studio ESP32C3CoreBoard**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `weactstudio_esp32c3coreboard` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32C3` | Native dual-core/accelerated processing |
| **Operating Frequency... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 124 KB of unfragmented dynamic heap (accounting f... | weactstudio_esp32c3coreboard | ESP32C3 | WeAct Studio | 409,600 | 393,216 |
pyintel_hw_cot_002981 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 136 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Adafruit ESP32-S2 Feather Development Board**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `featheresp32-s2` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32S2` | Native dual-core/accelerated processing |
| **Operating Frequenc... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 136 KB of unfragmented dynamic heap (accounting f... | featheresp32-s2 | ESP32S2 | Adafruit | 327,680 | 4,194,304 |
pyintel_hw_cot_002982 | native_usb_emulation | I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable en... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Adafruit Circuit Playground Classic**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `circuitplay_classic` | Registered entry in Open Board Registry |
| **Microcontroller** | `ATMEGA32U4` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / N... | <start_of_turn>user
I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY suppor... | circuitplay_classic | ATMEGA32U4 | Adafruit | 2,560 | 28,672 |
pyintel_hw_cot_002983 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 144 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **4D Systems GEN4-ESP32 16MB (ESP32S3-R8N16)**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `4d_systems_esp32s3_gen4_r8n16` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32S3` | Native dual-core/accelerated processing |
| **Opera... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 144 KB of unfragmented dynamic heap (accounting f... | 4d_systems_esp32s3_gen4_r8n16 | ESP32S3 | 4D Systems | 327,680 | 16,777,216 |
pyintel_hw_cot_002984 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **PYBStick Lite 26**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `pybstick26_lite` | Verified Open Board Registry entry |
| **MCU Core** | `STM32F401CEU6` | High-speed real-time core with hardware math |
| **Core Clock** | 84 MHz | Co... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | pybstick26_lite | STM32F401CEU6 | PYBStick | 98,304 | 524,288 |
pyintel_hw_cot_002985 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 96.0 kHz 16-bit mono produces $96.0 \times 10^3 \times 2 \approx 192,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 2048-point buffer represents $T_{window} = 2048 / (96.0 \times 10^3) \approx 21.33 \text{ ms}$.
- **Processi... | ### Recommended Board: **XinaBox CW02**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `xinabox_cw02` | Verified Open Board Registry entry |
| **Processor Core** | `ESP32` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 240 MHz | FFT computes in $< 2 \text{ ms}$ (well below 21... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | xinabox_cw02 | ESP32 | XinaBox | 327,680 | 4,194,304 |
pyintel_hw_cot_002986 | native_usb_emulation | I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoin... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **PicoADK v2**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `datanoisetv_picoadk_v2` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2350` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HID/... | <start_of_turn>user
I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting ... | datanoisetv_picoadk_v2 | RP2350 | DatanoiseTV | 524,288 | 4,194,304 |
pyintel_hw_cot_002987 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 40 kHz PWM, each control cycle is $T = 1 / 40\text{ kHz} = 25.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **ST Nucleo H743ZI**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `nucleo_h743zi` | Verified Open Board Registry entry |
| **MCU Core** | `STM32H743ZIT6` | High-speed real-time core with hardware math |
| **Core Clock** | 400 MHz | Com... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | nucleo_h743zi | STM32H743ZIT6 | ST | 524,288 | 2,097,152 |
pyintel_hw_cot_002988 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 25 kHz PWM, each control cycle is $T = 1 / 25\text{ kHz} = 40.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Motion 2350 Pro**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `cytron_motion_2350_pro` | Verified Open Board Registry entry |
| **MCU Core** | `RP2350` | High-speed real-time core with hardware math |
| **Core Clock** | 150 MHz | Co... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | cytron_motion_2350_pro | RP2350 | Cytron | 524,288 | 2,097,152 |
pyintel_hw_cot_002989 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 156 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Generic - BK7231T (Tuya)**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `generic-bk7231t-qfn32-tuya` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `BK7231T` | Native dual-core/accelerated processing |
| **Operating Frequency** | 12... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 156 KB of unfragmented dynamic heap (accounting f... | generic-bk7231t-qfn32-tuya | BK7231T | Generic | 262,144 | 1,083,136 |
pyintel_hw_cot_002990 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 214 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 320 pixels width $\times$ 240 pixels height = 76,800 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $320 \times 240 \times 2 = 153,600 \text{ bytes} = 150 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **WEMOS LOLIN S3**
| Constraint Parameter | Required Budget | Board Capability (`lolin_s3`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 150 KB (320x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 32 KB | Supported with substantial overhead |
| **Total... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 214 KB of conti... | lolin_s3 | ESP32S3 | WEMOS | 327,680 | 16,777,216 |
pyintel_hw_cot_002991 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 124 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **NiceMCU XH-WB3S**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `xh-wb3s` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `BK7238` | Native dual-core/accelerated processing |
| **Operating Frequency** | 120 MHz | Sufficient throughput... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 124 KB of unfragmented dynamic heap (accounting f... | xh-wb3s | BK7238 | SparkleIoT | 262,144 | 1,083,136 |
pyintel_hw_cot_002992 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 180 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **WEMOS LOLIN D32**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `lolin_d32` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient throughpu... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 180 KB of unfragmented dynamic heap (accounting f... | lolin_d32 | ESP32 | WEMOS | 327,680 | 4,194,304 |
pyintel_hw_cot_002993 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **DFRobot Romeo ESP32-S3**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C C... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | dfrobot_romeo_esp32s3 | ESP32S3 | DFRobot | 327,680 | 16,777,216 |
pyintel_hw_cot_002994 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 240 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 240 pixels width $\times$ 240 pixels height = 57,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $240 \times 240 \times 2 = 115,200 \text{ bytes} = 112 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **WEMOS LOLIN32**
| Constraint Parameter | Required Budget | Board Capability (`lolin32`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 112 KB (240x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 96 KB | Supported with substantial overhead |
| **Total S... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 240 KB of conti... | lolin32 | ESP32 | WEMOS | 327,680 | 4,194,304 |
pyintel_hw_cot_002995 | native_usb_emulation | I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoi... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Feather RP2040 DVI**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `adafruit_feather_dvi` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2040` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custo... | <start_of_turn>user
I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting... | adafruit_feather_dvi | RP2040 | Adafruit | 262,144 | 8,388,608 |
pyintel_hw_cot_002996 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 396 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **Pico2XXL**
| Constraint Parameter | Required Budget | Board Capability (`olimex_pico2xxl`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 64 KB | Supported with substantial overhead |
| **Tota... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 396 KB of conti... | olimex_pico2xxl | RP2350 | Olimex | 524,288 | 16,777,216 |
pyintel_hw_cot_002997 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 f... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 2000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (12V). Requires wide DC input step-down regulator or autom... | ### Recommended Board: **SparkFun LoRa Gateway 1-Channel**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `sparkfun_lora_gateway_1-channel` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, ... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling ca... | sparkfun_lora_gateway_1-channel | ESP32 | SparkFun | 327,680 | 4,194,304 |
pyintel_hw_cot_002998 | native_usb_emulation | I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoi... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **RPICO32**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `ilabs_rpico32` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2040` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HID/MIDI/CDC des... | <start_of_turn>user
I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting... | ilabs_rpico32 | RP2040 | iLabs | 262,144 | 8,388,608 |
pyintel_hw_cot_002999 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 164 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Espressif ESP32-C3-DevKitC-02**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `esp32-c3-devkitc-02` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32C3` | Native dual-core/accelerated processing |
| **Operating Frequency** | 160 ... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 164 KB of unfragmented dynamic heap (accounting f... | esp32-c3-devkitc-02 | ESP32C3 | Espressif | 327,680 | 4,194,304 |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.