id large_stringlengths 21 21 | domain large_stringclasses 7
values | instruction large_stringclasses 115
values | reasoning large_stringlengths 1.07k 5.05k | response large_stringlengths 677 1.11k | text large_stringlengths 2.31k 6.39k | target_board_id large_stringclasses 863
values | mcu large_stringclasses 201
values | vendor large_stringclasses 231
values | ram_bytes int64 2.05k 8.59B | rom_bytes int64 0 1.07B |
|---|---|---|---|---|---|---|---|---|---|---|
pyintel_hw_cot_003900 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 fr... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 500 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (12V). Requires wide DC input step-down regulator or automo... | ### Recommended Board: **ST Nucleo F446ZE**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `nucleo_f446ze` | Registered open-hardware entry |
| **MCU Architecture** | `STM32F446ZET6` | High-speed real-time core |
| **CAN Bus Interface** | can | Hardware frame filtration... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling cap... | nucleo_f446ze | STM32F446ZET6 | ST | 131,072 | 524,288 |
pyintel_hw_cot_003901 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 25 kHz PWM, each control cycle is $T = 1 / 25\text{ kHz} = 40.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Challenger 2350 NB-IoT**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `challenger_2350_nbiot` | Verified Open Board Registry entry |
| **MCU Core** | `RP2350` | High-speed real-time core with hardware math |
| **Core Clock** | 150 MH... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | challenger_2350_nbiot | RP2350 | iLabs | 524,288 | 8,388,608 |
pyintel_hw_cot_003902 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **WEMOS D1 MINI ESP32**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Cont... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | wemos_d1_mini32 | ESP32 | WEMOS | 327,680 | 4,194,304 |
pyintel_hw_cot_003903 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 128 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **M5Stack StampS3**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `m5stack-stamps3` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32S3` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient t... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 128 KB of unfragmented dynamic heap (accounting f... | m5stack-stamps3 | ESP32S3 | M5Stack | 327,680 | 8,388,608 |
pyintel_hw_cot_003904 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 140 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Imbrios LogSens V1P1**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `imbrios-logsens-v1p1` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Suff... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 140 KB of unfragmented dynamic heap (accounting f... | imbrios-logsens-v1p1 | ESP32 | Imbrios | 327,680 | 4,194,304 |
pyintel_hw_cot_003905 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 25 kHz PWM, each control cycle is $T = 1 / 25\text{ kHz} = 40.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Helios**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `0xcb_helios` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** | 133 MHz | Completes FOC loop in ... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | 0xcb_helios | RP2040 | 0xCB | 262,144 | 16,777,216 |
pyintel_hw_cot_003906 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **Ai-Thinker ESP-C3-M1-I-Kit**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | esp32-c3-m1i-kit | ESP32C3 | Ai-Thinker | 327,680 | 4,194,304 |
pyintel_hw_cot_003907 | native_usb_emulation | I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoin... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Adafruit Feather M0**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `adafruit_feather_m0` | Registered entry in Open Board Registry |
| **Microcontroller** | `SAMD21G18A` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | C... | <start_of_turn>user
I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting ... | adafruit_feather_m0 | SAMD21G18A | Adafruit | 32,768 | 262,144 |
pyintel_hw_cot_003908 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **ST Nucleo G0B1RE**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `nucleo_g0b1re` | Verified Open Board Registry entry |
| **MCU Core** | `STM32G0B1RET6` | High-speed real-time core with hardware math |
| **Core Clock** | 64 MHz | Comp... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | nucleo_g0b1re | STM32G0B1RET6 | ST | 147,456 | 524,288 |
pyintel_hw_cot_003909 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 240 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 240 pixels width $\times$ 240 pixels height = 57,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $240 \times 240 \times 2 = 115,200 \text{ bytes} = 112 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **Quectel EC100Y LTE Cat.1 Module**
| Constraint Parameter | Required Budget | Board Capability (`ec100y`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 112 KB (240x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 96 KB | Supported with substantial overh... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 240 KB of conti... | ec100y | ASR1601 | Quectel Wireless Solutions Co., Ltd. | 524,288 | 1,048,576 |
pyintel_hw_cot_003910 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 172 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **DOIT ESP32 DEVKIT V1**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `esp32doit-devkit-v1` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Suffi... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 172 KB of unfragmented dynamic heap (accounting f... | esp32doit-devkit-v1 | ESP32 | DOIT | 327,680 | 4,194,304 |
pyintel_hw_cot_003911 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 240 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 240 pixels width $\times$ 240 pixels height = 57,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $240 \times 240 \times 2 = 115,200 \text{ bytes} = 112 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **Trueverit ESP32 Universal IoT Driver MK III**
| Constraint Parameter | Required Budget | Board Capability (`trueverit-iot-driver-mk3`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 112 KB (240x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 96 KB | Su... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 240 KB of conti... | trueverit-iot-driver-mk3 | ESP32 | Trueverit | 327,680 | 4,194,304 |
pyintel_hw_cot_003912 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **BluesWireless Swan R5**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `bw_swan_r5` | Verified Open Board Registry entry |
| **MCU Core** | `STM32L4R5ZIY6` | High-speed real-time core with hardware math |
| **Core Clock** | 120 MHz | C... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | bw_swan_r5 | STM32L4R5ZIY6 | BluesWireless | 655,360 | 2,097,152 |
pyintel_hw_cot_003913 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 25 kHz PWM, each control cycle is $T = 1 / 25\text{ kHz} = 40.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **u-blox C030-U201 IoT Starter Kit**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `ublox_c030_u201` | Verified Open Board Registry entry |
| **MCU Core** | `STM32F437VG` | High-speed real-time core with hardware math |
| **Core Clock**... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | ublox_c030_u201 | STM32F437VG | u-blox | 262,144 | 1,048,576 |
pyintel_hw_cot_003914 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 176 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 240 pixels width $\times$ 240 pixels height = 57,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $240 \times 240 \times 2 = 115,200 \text{ bytes} = 112 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **M5Stack FIRE**
| Constraint Parameter | Required Budget | Board Capability (`m5stack-fire`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 112 KB (240x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 32 KB | Supported with substantial overhead |
| **Tot... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 176 KB of conti... | m5stack-fire | ESP32 | M5Stack | 4,521,984 | 16,777,216 |
pyintel_hw_cot_003915 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 140 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **TTGO T1**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `ttgo-t1` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient throughput for TLS ... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 140 KB of unfragmented dynamic heap (accounting f... | ttgo-t1 | ESP32 | TTGO | 327,680 | 4,194,304 |
pyintel_hw_cot_003916 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 124 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Generic - LN882H**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `generic-ln882h` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `LN882HK` | Native dual-core/accelerated processing |
| **Operating Frequency** | 160 MHz | Sufficient t... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 124 KB of unfragmented dynamic heap (accounting f... | generic-ln882h | LN882HK | Generic | 302,080 | 1,228,800 |
pyintel_hw_cot_003917 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 40 kHz PWM, each control cycle is $T = 1 / 40\text{ kHz} = 25.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **PicoADK**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `datanoisetv_picoadk` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** | 133 MHz | Completes FOC... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | datanoisetv_picoadk | RP2040 | DatanoiseTV | 262,144 | 2,097,152 |
pyintel_hw_cot_003918 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 44.1 kHz 16-bit mono produces $44.1 \times 10^3 \times 2 \approx 88,200 \text{ bytes/sec}$.
- **FFT Window Duration**: A 2048-point buffer represents $T_{window} = 2048 / (44.1 \times 10^3) \approx 46.44 \text{ ms}$.
- **Processin... | ### Recommended Board: **WEMOS LOLIN32 Lite**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `lolin32_lite` | Verified Open Board Registry entry |
| **Processor Core** | `ESP32` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 240 MHz | FFT computes in $< 2 \text{ ms}$ (well be... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | lolin32_lite | ESP32 | WEMOS | 327,680 | 4,194,304 |
pyintel_hw_cot_003919 | native_usb_emulation | I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoin... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Mizu RP2040**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `viyalab_mizu` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2040` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HID/MIDI/CDC ... | <start_of_turn>user
I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting ... | viyalab_mizu | RP2040 | Viyalab | 262,144 | 8,388,608 |
pyintel_hw_cot_003920 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capabi... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 500 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (7V–28V DC wide input). Requires wide DC input step-down re... | ### Recommended Board: **M5Stack Core ESP32 16M**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `m5stack-core-esp32-16M` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, bluetooth, etherne... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient inter... | m5stack-core-esp32-16M | ESP32 | M5Stack | 532,480 | 16,777,216 |
pyintel_hw_cot_003921 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 208 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 240 pixels width $\times$ 240 pixels height = 57,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $240 \times 240 \times 2 = 115,200 \text{ bytes} = 112 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **Generic - LN882H (Tuya)**
| Constraint Parameter | Required Budget | Board Capability (`generic-ln882h-tuya`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 112 KB (240x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 64 KB | Supported with substantial ... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 208 KB of conti... | generic-ln882h-tuya | LN882HK | Generic | 302,080 | 1,228,800 |
pyintel_hw_cot_003922 | native_usb_emulation | I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable en... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **LinkIt Smart 7688 Duo**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `smart7688` | Registered entry in Open Board Registry |
| **Microcontroller** | `ATMEGA32U4` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HI... | <start_of_turn>user
I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY suppor... | smart7688 | ATMEGA32U4 | MediaTek Labs | 2,560 | 28,672 |
pyintel_hw_cot_003923 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 136 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Pycom WiPy3**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `wipy3` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient throughput for TL... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 136 KB of unfragmented dynamic heap (accounting f... | wipy3 | ESP32 | Pycom Ltd. | 1,310,720 | 4,194,304 |
pyintel_hw_cot_003924 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 40 kHz PWM, each control cycle is $T = 1 / 40\text{ kHz} = 25.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **RP2040 Zero**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `waveshare_rp2040_zero` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** | 133 MHz | Complet... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | waveshare_rp2040_zero | RP2040 | Waveshare | 262,144 | 2,097,152 |
pyintel_hw_cot_003925 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 fr... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 500 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (12V). Requires wide DC input step-down regulator or automo... | ### Recommended Board: **Trueverit ESP32 Universal IoT Driver**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `trueverit-iot-driver` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, blueto... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling cap... | trueverit-iot-driver | ESP32 | Trueverit | 327,680 | 4,194,304 |
pyintel_hw_cot_003926 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 fr... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 500 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (24V). Requires wide DC input step-down regulator or automo... | ### Recommended Board: **Espressif ESP32 Dev Module**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `esp32dev` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, bluetooth, ethernet, can | H... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling cap... | esp32dev | ESP32 | Espressif | 327,680 | 4,194,304 |
pyintel_hw_cot_003927 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 172 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Generic - LN882H (Tuya)**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `generic-ln882h-tuya` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `LN882HK` | Native dual-core/accelerated processing |
| **Operating Frequency** | 160 MHz | ... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 172 KB of unfragmented dynamic heap (accounting f... | generic-ln882h-tuya | LN882HK | Generic | 302,080 | 1,228,800 |
pyintel_hw_cot_003928 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 120 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **logicrom Spark LTE-G (EC200U)**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `logicrom_spark` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `RDA8910` | Native dual-core/accelerated processing |
| **Operating Frequency** | 500 MHz |... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 120 KB of unfragmented dynamic heap (accounting f... | logicrom_spark | RDA8910 | Waybyte Solutions | 524,288 | 1,048,576 |
pyintel_hw_cot_003929 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 188 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **OLIMEX ESP32-GATEWAY**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `esp32-gateway` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient ... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 188 KB of unfragmented dynamic heap (accounting f... | esp32-gateway | ESP32 | OLIMEX | 327,680 | 4,194,304 |
pyintel_hw_cot_003930 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 96.0 kHz 16-bit mono produces $96.0 \times 10^3 \times 2 \approx 192,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 1024-point buffer represents $T_{window} = 1024 / (96.0 \times 10^3) \approx 10.67 \text{ ms}$.
- **Processi... | ### Recommended Board: **Raspberry**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `breadstick_raspberry` | Verified Open Board Registry entry |
| **Processor Core** | `RP2040` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 133 MHz | FFT computes in $< 2 \text{ ms}$ (well be... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | breadstick_raspberry | RP2040 | Breadstick | 262,144 | 16,777,216 |
pyintel_hw_cot_003931 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 fr... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 500 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (24V). Requires wide DC input step-down regulator or automo... | ### Recommended Board: **Adafruit ESP32 Feather**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `featheresp32` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, bluetooth, ethernet, can | H... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling cap... | featheresp32 | ESP32 | Adafruit | 327,680 | 4,194,304 |
pyintel_hw_cot_003932 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 40 kHz PWM, each control cycle is $T = 1 / 40\text{ kHz} = 25.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **DevEBox H743VITX**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `devebox_h743vitx` | Verified Open Board Registry entry |
| **MCU Core** | `STM32H743VIT6` | High-speed real-time core with hardware math |
| **Core Clock** | 480 MHz | ... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | devebox_h743vitx | STM32H743VIT6 | DevEBox | 524,288 | 2,097,152 |
pyintel_hw_cot_003933 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 40 kHz PWM, each control cycle is $T = 1 / 40\text{ kHz} = 25.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **STM32F103ZE (64k RAM. 512k Flash)**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `genericSTM32F103ZE` | Verified Open Board Registry entry |
| **MCU Core** | `STM32F103ZET6` | High-speed real-time core with hardware math |
| **Core C... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | genericSTM32F103ZE | STM32F103ZET6 | Generic | 65,536 | 524,288 |
pyintel_hw_cot_003934 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 214 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 320 pixels width $\times$ 240 pixels height = 76,800 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $320 \times 240 \times 2 = 153,600 \text{ bytes} = 150 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **Adafruit ESP32-S2 Feather Development Board**
| Constraint Parameter | Required Budget | Board Capability (`featheresp32-s2`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 150 KB (320x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 32 KB | Supported w... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 214 KB of conti... | featheresp32-s2 | ESP32S2 | Adafruit | 327,680 | 4,194,304 |
pyintel_hw_cot_003935 | native_usb_emulation | I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable en... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **XIAO RP2040**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `seeed_xiao_rp2040` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2040` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HID/MIDI... | <start_of_turn>user
I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY suppor... | seeed_xiao_rp2040 | RP2040 | Seeed | 262,144 | 2,097,152 |
pyintel_hw_cot_003936 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 40 kHz PWM, each control cycle is $T = 1 / 40\text{ kHz} = 25.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Pico2XL**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `olimex_pico2xl` | Verified Open Board Registry entry |
| **MCU Core** | `RP2350` | High-speed real-time core with hardware math |
| **Core Clock** | 150 MHz | Completes FOC loop... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | olimex_pico2xl | RP2350 | Olimex | 524,288 | 2,097,152 |
pyintel_hw_cot_003937 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Trinkey RP2040 QT**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `adafruit_trinkeyrp2040qt` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** | 133 MHz ... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | adafruit_trinkeyrp2040qt | RP2040 | Adafruit | 262,144 | 8,388,608 |
pyintel_hw_cot_003938 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **oddWires IoT-Bus Io**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Cont... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | iotbusio | ESP32 | oddWires | 327,680 | 4,194,304 |
pyintel_hw_cot_003939 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 25 kHz PWM, each control cycle is $T = 1 / 25\text{ kHz} = 40.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **W6300-EVB-Pico2**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `wiznet_6300_evb_pico2` | Verified Open Board Registry entry |
| **MCU Core** | `RP2350` | High-speed real-time core with hardware math |
| **Core Clock** | 150 MHz | Com... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | wiznet_6300_evb_pico2 | RP2350 | WIZnet | 524,288 | 2,097,152 |
pyintel_hw_cot_003940 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 164 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Heltec Wireless Stick Lite**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `heltec_wireless_stick_lite` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 24... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 164 KB of unfragmented dynamic heap (accounting f... | heltec_wireless_stick_lite | ESP32 | Heltec Automation | 327,680 | 4,194,304 |
pyintel_hw_cot_003941 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S doub... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 48.0 kHz 16-bit mono produces $48.0 \times 10^3 \times 2 \approx 96,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 512-point buffer represents $T_{window} = 512 / (48.0 \times 10^3) \approx 10.67 \text{ ms}$.
- **Processing ... | ### Recommended Board: **AI-Thinker A9 GSM Module**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `a9` | Verified Open Board Registry entry |
| **Processor Core** | `RDA8955` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 178 MHz | FFT computes in $< 2 \text{ ms}$ (well belo... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support c... | a9 | RDA8955 | Ai-Thinker Co., Ltd. | 1,040,384 | 589,824 |
pyintel_hw_cot_003942 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **Adafruit QT Py ESP32-C3**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C ... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | adafruit_qtpy_esp32c3 | ESP32C3 | Adafruit | 327,680 | 4,194,304 |
pyintel_hw_cot_003943 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 96.0 kHz 16-bit mono produces $96.0 \times 10^3 \times 2 \approx 192,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 1024-point buffer represents $T_{window} = 1024 / (96.0 \times 10^3) \approx 10.67 \text{ ms}$.
- **Processi... | ### Recommended Board: **ST Nucleo L486RG**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `nucleo_l486rg` | Verified Open Board Registry entry |
| **Processor Core** | `STM32L486RGT6` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 80 MHz | FFT computes in $< 2 \text{ ms}$ (w... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | nucleo_l486rg | STM32L486RGT6 | ST | 131,072 | 1,048,576 |
pyintel_hw_cot_003944 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 96.0 kHz 16-bit mono produces $96.0 \times 10^3 \times 2 \approx 192,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 2048-point buffer represents $T_{window} = 2048 / (96.0 \times 10^3) \approx 21.33 \text{ ms}$.
- **Processi... | ### Recommended Board: **STM32F401RB (64k RAM. 128k Flash)**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `genericSTM32F401RB` | Verified Open Board Registry entry |
| **Processor Core** | `STM32F401RBT6` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 84 MHz | FFT computes ... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | genericSTM32F401RB | STM32F401RBT6 | Generic | 65,536 | 131,072 |
pyintel_hw_cot_003945 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **Plasma2040**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Controller** ... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | pimoroni_plasma2040 | RP2040 | Pimoroni | 262,144 | 2,097,152 |
pyintel_hw_cot_003946 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 44.1 kHz 16-bit mono produces $44.1 \times 10^3 \times 2 \approx 88,200 \text{ bytes/sec}$.
- **FFT Window Duration**: A 2048-point buffer represents $T_{window} = 2048 / (44.1 \times 10^3) \approx 46.44 \text{ ms}$.
- **Processin... | ### Recommended Board: **RAK11300**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `rakwireless_rak11300` | Verified Open Board Registry entry |
| **Processor Core** | `RP2040` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 133 MHz | FFT computes in $< 2 \text{ ms}$ (well bel... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | rakwireless_rak11300 | RP2040 | RAKwireless | 262,144 | 2,097,152 |
pyintel_hw_cot_003947 | native_usb_emulation | I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoin... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **SparkFun RedBoard Turbo**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `sparkfun_redboard_turbo` | Registered entry in Open Board Registry |
| **Microcontroller** | `SAMD21G18A` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Dr... | <start_of_turn>user
I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting ... | sparkfun_redboard_turbo | SAMD21G18A | SparkFun | 32,768 | 262,144 |
pyintel_hw_cot_003948 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 156 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **LilyGo T3-S3**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `lilygo-t3-s3` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32S3` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient through... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 156 KB of unfragmented dynamic heap (accounting f... | lilygo-t3-s3 | ESP32S3 | LilyGo | 327,680 | 4,194,304 |
pyintel_hw_cot_003949 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **ST Nucleo F756ZG**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `nucleo_f756zg` | Verified Open Board Registry entry |
| **MCU Core** | `STM32F756ZG` | High-speed real-time core with hardware math |
| **Core Clock** | 216 MHz | Compl... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | nucleo_f756zg | STM32F756ZG | ST | 327,680 | 1,048,576 |
pyintel_hw_cot_003950 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 240 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 240 pixels width $\times$ 240 pixels height = 57,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $240 \times 240 \times 2 = 115,200 \text{ bytes} = 112 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **CB2L Wi-Fi Module**
| Constraint Parameter | Required Budget | Board Capability (`cb2l`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 112 KB (240x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 96 KB | Supported with substantial overhead |
| **Total ... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 240 KB of conti... | cb2l | BK7231N | Tuya Inc. | 262,144 | 1,083,136 |
pyintel_hw_cot_003951 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 136 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **WR2LE Wi-Fi Module**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `wr2le` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `RTL8710BX` | Native dual-core/accelerated processing |
| **Operating Frequency** | 62.5 MHz | Sufficient throu... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 136 KB of unfragmented dynamic heap (accounting f... | wr2le | RTL8710BX | Tuya Inc. | 262,144 | 806,912 |
pyintel_hw_cot_003952 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 364 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **MKS THR42**
| Constraint Parameter | Required Budget | Board Capability (`mksthr42`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 32 KB | Supported with substantial overhead |
| **Total SRAM... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 364 KB of conti... | mksthr42 | RP2040 | Makerbase | 262,144 | 1,048,576 |
pyintel_hw_cot_003953 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **Adafruit QT Py ESP32-C3**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C ... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | adafruit_qtpy_esp32c3 | ESP32C3 | Adafruit | 327,680 | 4,194,304 |
pyintel_hw_cot_003954 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **Feather RP2040 Adalogger**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | adafruit_feather_adalogger | RP2040 | Adafruit | 262,144 | 8,388,608 |
pyintel_hw_cot_003955 | native_usb_emulation | I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoi... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Adafruit QT Py ESP32-S2**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `adafruit_qtpy_esp32s2` | Registered entry in Open Board Registry |
| **Microcontroller** | `ESP32S2` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver ... | <start_of_turn>user
I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting... | adafruit_qtpy_esp32s2 | ESP32S2 | Adafruit | 327,680 | 4,194,304 |
pyintel_hw_cot_003956 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **DudesCab**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Controller** | ... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | DudesCab | RP2040 | L'atelier d'Arnoz | 262,144 | 4,194,304 |
pyintel_hw_cot_003957 | native_usb_emulation | I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoi... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Maker Uno RP2040**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `cytron_maker_uno_rp2040` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2040` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Cust... | <start_of_turn>user
I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting... | cytron_maker_uno_rp2040 | RP2040 | Cytron | 262,144 | 2,097,152 |
pyintel_hw_cot_003958 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 96.0 kHz 16-bit mono produces $96.0 \times 10^3 \times 2 \approx 192,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 1024-point buffer represents $T_{window} = 1024 / (96.0 \times 10^3) \approx 10.67 \text{ ms}$.
- **Processi... | ### Recommended Board: **XIAO RP2350**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `seeed_xiao_rp2350` | Verified Open Board Registry entry |
| **Processor Core** | `RP2350` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 150 MHz | FFT computes in $< 2 \text{ ms}$ (well bel... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | seeed_xiao_rp2350 | RP2350 | Seeed | 524,288 | 2,097,152 |
pyintel_hw_cot_003959 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **ST Nucleo F446ZE**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `nucleo_f446ze` | Verified Open Board Registry entry |
| **MCU Core** | `STM32F446ZET6` | High-speed real-time core with hardware math |
| **Core Clock** | 180 MHz | Com... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | nucleo_f446ze | STM32F446ZET6 | ST | 131,072 | 524,288 |
pyintel_hw_cot_003960 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 136 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Heltec Wireless Stick Lite**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `heltec_wireless_stick_lite` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 24... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 136 KB of unfragmented dynamic heap (accounting f... | heltec_wireless_stick_lite | ESP32 | Heltec Automation | 327,680 | 4,194,304 |
pyintel_hw_cot_003961 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capab... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 2000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (7V–28V DC wide input). Requires wide DC input step-down r... | ### Recommended Board: **AZ-Delivery ESP-32 Dev Kit C V4**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `az-delivery-devkit-v4` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, bluetooth,... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient inte... | az-delivery-devkit-v4 | ESP32 | AZ-Delivery | 532,480 | 4,194,304 |
pyintel_hw_cot_003962 | native_usb_emulation | I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoin... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **WEMOS LOLIN S3**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `lolin_s3` | Registered entry in Open Board Registry |
| **Microcontroller** | `ESP32S3` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HID/MIDI/CDC ... | <start_of_turn>user
I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting ... | lolin_s3 | ESP32S3 | WEMOS | 327,680 | 16,777,216 |
pyintel_hw_cot_003963 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 f... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 1000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (24V). Requires wide DC input step-down regulator or autom... | ### Recommended Board: **ST Nucleo H563ZI**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `nucleo_h563zi` | Registered open-hardware entry |
| **MCU Architecture** | `STM32H563ZIT6U` | High-speed real-time core |
| **CAN Bus Interface** | can, ethernet | Hardware frame... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling ca... | nucleo_h563zi | STM32H563ZIT6U | ST | 655,360 | 2,097,152 |
pyintel_hw_cot_003964 | native_usb_emulation | I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoin... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **RP2040 Matrix**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `waveshare_rp2040_matrix` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2040` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom ... | <start_of_turn>user
I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting ... | waveshare_rp2040_matrix | RP2040 | Waveshare | 262,144 | 2,097,152 |
pyintel_hw_cot_003965 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 96.0 kHz 16-bit mono produces $96.0 \times 10^3 \times 2 \approx 192,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 2048-point buffer represents $T_{window} = 2048 / (96.0 \times 10^3) \approx 21.33 \text{ ms}$.
- **Processi... | ### Recommended Board: **Smart Bee Motion S3**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `bee_motion_s3` | Verified Open Board Registry entry |
| **Processor Core** | `ESP32S3` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 240 MHz | FFT computes in $< 2 \text{ ms}$ (wel... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | bee_motion_s3 | ESP32S3 | Smart Bee | 327,680 | 8,388,608 |
pyintel_hw_cot_003966 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 140 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Thunderboard Sense 2 Sensor-to-Cloud Advanced IoT**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `tb_sense_12` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `EFR32MG12P432F1024` | Native dual-core/accelerated processing |
| **Opera... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 140 KB of unfragmented dynamic heap (accounting f... | tb_sense_12 | EFR32MG12P432F1024 | Silicon Labs | 262,144 | 1,048,576 |
pyintel_hw_cot_003967 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 364 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **ArtronShop IOXESP32PS**
| Constraint Parameter | Required Budget | Board Capability (`ioxesp32ps`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 32 KB | Supported with substantial overhead |
... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 364 KB of conti... | ioxesp32ps | ESP32 | ArtronShop | 327,680 | 4,194,304 |
pyintel_hw_cot_003968 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **ST 32F413HDISCOVERY**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Cont... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | disco_f413zh | STM32F413ZHT6 | ST | 327,680 | 1,572,864 |
pyintel_hw_cot_003969 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 f... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 2000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (12V). Requires wide DC input step-down regulator or autom... | ### Recommended Board: **IoTaaP Magnolia**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `iotaap_magnolia` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, bluetooth, ethernet, can | Hardw... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling ca... | iotaap_magnolia | ESP32 | IoTaaP | 327,680 | 4,194,304 |
pyintel_hw_cot_003970 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **IRIV IO Controller**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Contr... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | cytron_iriv_io_controller | RP2350 | Cytron | 524,288 | 2,097,152 |
pyintel_hw_cot_003971 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 428 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **RP2040**
| Constraint Parameter | Required Budget | Board Capability (`generic`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 96 KB | Supported with substantial overhead |
| **Total SRAM Ava... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 428 KB of conti... | generic | RP2040 | Generic | 262,144 | 16,777,216 |
pyintel_hw_cot_003972 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 128 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **CB3L Wi-Fi Module**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `cb3l` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `BK7231N` | Native dual-core/accelerated processing |
| **Operating Frequency** | 120 MHz | Sufficient throughput... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 128 KB of unfragmented dynamic heap (accounting f... | cb3l | BK7231N | Tuya Inc. | 262,144 | 1,083,136 |
pyintel_hw_cot_003973 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 25 kHz PWM, each control cycle is $T = 1 / 25\text{ kHz} = 40.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **RP2350**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `generic_rp2350` | Verified Open Board Registry entry |
| **MCU Core** | `RP2350` | High-speed real-time core with hardware math |
| **Core Clock** | 150 MHz | Completes FOC loop ... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | generic_rp2350 | RP2350 | Generic | 524,288 | 16,777,216 |
pyintel_hw_cot_003974 | native_usb_emulation | I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoi... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **SparkFun SAMD21 Mini Breakout**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `sparkfun_samd21_mini_usb` | Registered entry in Open Board Registry |
| **Microcontroller** | `SAMD21G18A` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Na... | <start_of_turn>user
I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting... | sparkfun_samd21_mini_usb | SAMD21G18A | SparkFun | 32,768 | 262,144 |
pyintel_hw_cot_003975 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 148 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **SQFMI Watchy v2.0**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `watchy` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient throughput... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 148 KB of unfragmented dynamic heap (accounting f... | watchy | ESP32 | SQFMI | 327,680 | 4,194,304 |
pyintel_hw_cot_003976 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **RP2040 Plus**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `waveshare_rp2040_plus` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** | 133 MHz | Complet... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | waveshare_rp2040_plus | RP2040 | Waveshare | 262,144 | 4,194,304 |
pyintel_hw_cot_003977 | native_usb_emulation | I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoi... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Adafruit Feather 32u4**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `feather32u4` | Registered entry in Open Board Registry |
| **Microcontroller** | `ATMEGA32U4` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom ... | <start_of_turn>user
I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting... | feather32u4 | ATMEGA32U4 | Adafruit | 2,560 | 28,672 |
pyintel_hw_cot_003978 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 140 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **ElectronutLabs Blip**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `electronut_blip` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `NRF52840` | Native dual-core/accelerated processing |
| **Operating Frequency** | 64 MHz | Sufficie... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 140 KB of unfragmented dynamic heap (accounting f... | electronut_blip | NRF52840 | ElectronutLabs | 262,144 | 1,048,576 |
pyintel_hw_cot_003979 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 396 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **Espressif ESP32-PICO-DevKitM-2**
| Constraint Parameter | Required Budget | Board Capability (`esp32-pico-devkitm-2`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 64 KB | Supported with subs... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 396 KB of conti... | esp32-pico-devkitm-2 | ESP32 | Espressif Systems | 327,680 | 8,388,608 |
pyintel_hw_cot_003980 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 96.0 kHz 16-bit mono produces $96.0 \times 10^3 \times 2 \approx 192,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 1024-point buffer represents $T_{window} = 1024 / (96.0 \times 10^3) \approx 10.67 \text{ ms}$.
- **Processi... | ### Recommended Board: **Transceiver**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `picolume` | Verified Open Board Registry entry |
| **Processor Core** | `RP2040` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 133 MHz | FFT computes in $< 2 \text{ ms}$ (well below 10.7 m... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | picolume | RP2040 | PicoLume | 262,144 | 2,097,152 |
pyintel_hw_cot_003981 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 40 kHz PWM, each control cycle is $T = 1 / 40\text{ kHz} = 25.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Microsoft Azure IoT Development Kit (MXChip AZ3166)**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `mxchip_az3166` | Verified Open Board Registry entry |
| **MCU Core** | `STM32F412ZGT6` | High-speed real-time core with hardware math... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | mxchip_az3166 | STM32F412ZGT6 | MXChip | 262,144 | 1,048,576 |
pyintel_hw_cot_003982 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 176 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 240 pixels width $\times$ 240 pixels height = 57,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $240 \times 240 \times 2 = 115,200 \text{ bytes} = 112 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **AFW121T**
| Constraint Parameter | Required Budget | Board Capability (`afw121t`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 112 KB (240x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 32 KB | Supported with substantial overhead |
| **Total SRAM Av... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 176 KB of conti... | afw121t | RTL8710BX | 99iot(Shenzhen)co.,ltd | 262,144 | 479,232 |
pyintel_hw_cot_003983 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 25 kHz PWM, each control cycle is $T = 1 / 25\text{ kHz} = 40.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Challenger 2040 WiFi6/BLE**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `challenger_2040_wifi6_ble` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** |... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | challenger_2040_wifi6_ble | RP2040 | iLabs | 262,144 | 8,388,608 |
pyintel_hw_cot_003984 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 fr... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 500 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (12V). Requires wide DC input step-down regulator or automo... | ### Recommended Board: **ST Nucleo H745ZI-Q**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `nucleo_h745zi_q` | Registered open-hardware entry |
| **MCU Architecture** | `STM32H745ZIT6` | High-speed real-time core |
| **CAN Bus Interface** | can, ethernet | Hardware fr... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling cap... | nucleo_h745zi_q | STM32H745ZIT6 | ST | 524,288 | 1,048,576 |
pyintel_hw_cot_003985 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 25 kHz PWM, each control cycle is $T = 1 / 25\text{ kHz} = 40.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **ST Nucleo L432KC**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `nucleo_l432kc` | Verified Open Board Registry entry |
| **MCU Core** | `STM32L432KCU6` | High-speed real-time core with hardware math |
| **Core Clock** | 80 MHz | Comp... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | nucleo_l432kc | STM32L432KCU6 | ST | 65,536 | 262,144 |
pyintel_hw_cot_003986 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 156 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Espressif ESP32 Dev Module**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `esp32dev` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 156 KB of unfragmented dynamic heap (accounting f... | esp32dev | ESP32 | Espressif | 327,680 | 4,194,304 |
pyintel_hw_cot_003987 | native_usb_emulation | I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable en... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Freenove ESP32-S3 WROOM N8R8 (8MB Flash / 8MB PSRAM)**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `freenove_esp32_s3_wroom` | Registered entry in Open Board Registry |
| **Microcontroller** | `ESP32S3` | Direct native USB 2.0 FS silicon |
| **USB Sta... | <start_of_turn>user
I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY suppor... | freenove_esp32_s3_wroom | ESP32S3 | Freenove | 327,680 | 8,388,608 |
pyintel_hw_cot_003988 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 428 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **Neoway N716 LTE Cat.1 Module**
| Constraint Parameter | Required Budget | Board Capability (`n716`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 96 KB | Supported with substantial overhead |... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 428 KB of conti... | n716 | RDA8910 | Neoway Technology Co.Ltd. | 524,288 | 1,048,576 |
pyintel_hw_cot_003989 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 214 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 320 pixels width $\times$ 240 pixels height = 76,800 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $320 \times 240 \times 2 = 153,600 \text{ bytes} = 150 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **Adafruit QT Py ESP32-S3 No PSRAM**
| Constraint Parameter | Required Budget | Board Capability (`adafruit_qtpy_esp32s3_nopsram`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 150 KB (320x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 32 KB | Supporte... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 214 KB of conti... | adafruit_qtpy_esp32s3_nopsram | ESP32S3 | Adafruit | 327,680 | 8,388,608 |
pyintel_hw_cot_003990 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 120 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **OLIMEX ESP32-PRO**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `esp32-pro` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient throughp... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 120 KB of unfragmented dynamic heap (accounting f... | esp32-pro | ESP32 | OLIMEX | 327,680 | 4,194,304 |
pyintel_hw_cot_003991 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 214 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 320 pixels width $\times$ 240 pixels height = 76,800 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $320 \times 240 \times 2 = 153,600 \text{ bytes} = 150 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **LN-CB3S V1.0**
| Constraint Parameter | Required Budget | Board Capability (`ln-cb3s-v1.0`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 150 KB (320x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 32 KB | Supported with substantial overhead |
| **Tot... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 214 KB of conti... | ln-cb3s-v1.0 | LN882HK | Unknown | 302,080 | 1,228,800 |
pyintel_hw_cot_003992 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 40 kHz PWM, each control cycle is $T = 1 / 40\text{ kHz} = 25.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Plasma2350W**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `pimoroni_plasma2350w` | Verified Open Board Registry entry |
| **MCU Core** | `RP2350` | High-speed real-time core with hardware math |
| **Core Clock** | 150 MHz | Complete... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | pimoroni_plasma2350w | RP2350 | Pimoroni | 524,288 | 2,097,152 |
pyintel_hw_cot_003993 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 164 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **T1-M Wi-Fi Module**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `t1-m` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `BK7238` | Native dual-core/accelerated processing |
| **Operating Frequency** | 120 MHz | Sufficient throughput ... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 164 KB of unfragmented dynamic heap (accounting f... | t1-m | BK7238 | Tuya Inc. | 262,144 | 1,083,136 |
pyintel_hw_cot_003994 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **DevEBox H750VBTX**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Control... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | devebox_h750vbtx | STM32H750VBT6 | DevEBox | 131,072 | 524,288 |
pyintel_hw_cot_003995 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 112 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Adafruit Feather ESP32-S2 Reverse TFT**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `adafruit_feather_esp32s2_reversetft` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32S2` | Native dual-core/accelerated processing |
| **Oper... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 112 KB of unfragmented dynamic heap (accounting f... | adafruit_feather_esp32s2_reversetft | ESP32S2 | Adafruit | 327,680 | 4,194,304 |
pyintel_hw_cot_003996 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **Challenger 2040 LTE**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Cont... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | challenger_2040_lte | RP2040 | iLabs | 262,144 | 8,388,608 |
pyintel_hw_cot_003997 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 124 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **ArtronShop IOXESP32PS**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `ioxesp32ps` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient th... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 124 KB of unfragmented dynamic heap (accounting f... | ioxesp32ps | ESP32 | ArtronShop | 327,680 | 4,194,304 |
pyintel_hw_cot_003998 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 fr... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 500 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (12V). Requires wide DC input step-down regulator or automo... | ### Recommended Board: **oddWires IoT-Bus Io**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `iotbusio` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, bluetooth, ethernet, can | Hardware... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling cap... | iotbusio | ESP32 | oddWires | 327,680 | 4,194,304 |
pyintel_hw_cot_003999 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 25 kHz PWM, each control cycle is $T = 1 / 25\text{ kHz} = 40.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **RP2040 LCD 1.28**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `waveshare_rp2040_lcd_1_28` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** | 133 MHz |... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | waveshare_rp2040_lcd_1_28 | RP2040 | Waveshare | 262,144 | 2,097,152 |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.