id large_stringlengths 21 21 | domain large_stringclasses 7
values | instruction large_stringclasses 115
values | reasoning large_stringlengths 1.07k 5.05k | response large_stringlengths 677 1.11k | text large_stringlengths 2.31k 6.39k | target_board_id large_stringclasses 863
values | mcu large_stringclasses 201
values | vendor large_stringclasses 231
values | ram_bytes int64 2.05k 8.59B | rom_bytes int64 0 1.07B |
|---|---|---|---|---|---|---|---|---|---|---|
pyintel_hw_cot_004400 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 396 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **Onehorse ESP32 Dev Module**
| Constraint Parameter | Required Budget | Board Capability (`onehorse32dev`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 64 KB | Supported with substantial over... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 396 KB of conti... | onehorse32dev | ESP32 | Onehorse | 327,680 | 4,194,304 |
pyintel_hw_cot_004401 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capab... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 2000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (7V–28V DC wide input). Requires wide DC input step-down r... | ### Recommended Board: **ST Nucleo F334R8**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `nucleo_f334r8` | Registered open-hardware entry |
| **MCU Architecture** | `STM32F334R8T6` | High-speed real-time core |
| **CAN Bus Interface** | can | Hardware frame filtration... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient inte... | nucleo_f334r8 | STM32F334R8T6 | ST | 16,384 | 65,536 |
pyintel_hw_cot_004402 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **Adafruit QT Py ESP32**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Con... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | adafruit_qtpy_esp32 | ESP32 | Adafruit | 327,680 | 8,388,608 |
pyintel_hw_cot_004403 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 112 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **LilyGo T-Display-S3**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `lilygo-t-display-s3` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32S3` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Suff... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 112 KB of unfragmented dynamic heap (accounting f... | lilygo-t-display-s3 | ESP32S3 | LilyGo | 327,680 | 16,777,216 |
pyintel_hw_cot_004404 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 164 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Espressif ESP32-S3-Box**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `esp32s3box` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32S3` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 164 KB of unfragmented dynamic heap (accounting f... | esp32s3box | ESP32S3 | Espressif | 327,680 | 16,777,216 |
pyintel_hw_cot_004405 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 144 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Adafruit ESP32-S2 Feather Development Board**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `featheresp32-s2` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32S2` | Native dual-core/accelerated processing |
| **Operating Frequenc... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 144 KB of unfragmented dynamic heap (accounting f... | featheresp32-s2 | ESP32S2 | Adafruit | 327,680 | 4,194,304 |
pyintel_hw_cot_004406 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 120 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **WR2L Wi-Fi Module**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `wr2l` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `RTL8710BX` | Native dual-core/accelerated processing |
| **Operating Frequency** | 62.5 MHz | Sufficient through... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 120 KB of unfragmented dynamic heap (accounting f... | wr2l | RTL8710BX | Tuya Inc. | 262,144 | 806,912 |
pyintel_hw_cot_004407 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 25 kHz PWM, each control cycle is $T = 1 / 25\text{ kHz} = 40.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **ST 32F413HDISCOVERY**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `disco_f413zh` | Verified Open Board Registry entry |
| **MCU Core** | `STM32F413ZHT6` | High-speed real-time core with hardware math |
| **Core Clock** | 100 MHz | C... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | disco_f413zh | STM32F413ZHT6 | ST | 327,680 | 1,572,864 |
pyintel_hw_cot_004408 | native_usb_emulation | I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable en... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Moteino M0**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `moteino_zero` | Registered entry in Open Board Registry |
| **Microcontroller** | `SAMD21G18A` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HID/MIDI/C... | <start_of_turn>user
I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY suppor... | moteino_zero | SAMD21G18A | LowPowerLab | 32,768 | 262,144 |
pyintel_hw_cot_004409 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 48.0 kHz 16-bit mono produces $48.0 \times 10^3 \times 2 \approx 96,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 2048-point buffer represents $T_{window} = 2048 / (48.0 \times 10^3) \approx 42.67 \text{ ms}$.
- **Processin... | ### Recommended Board: **Raspberry Pi Pico**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `pico` | Verified Open Board Registry entry |
| **Processor Core** | `RP2040` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 133 MHz | FFT computes in $< 2 \text{ ms}$ (well below 42.7... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | pico | RP2040 | Raspberry Pi | 270,336 | 2,097,152 |
pyintel_hw_cot_004410 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **XIAO RP2350**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Controller**... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | seeed_xiao_rp2350 | RP2350 | Seeed | 524,288 | 2,097,152 |
pyintel_hw_cot_004411 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 fr... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 500 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (24V). Requires wide DC input step-down regulator or automo... | ### Recommended Board: **OLIMEX ESP32-EVB**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `esp32-evb` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, bluetooth, ethernet, can | Hardware f... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling cap... | esp32-evb | ESP32 | OLIMEX | 327,680 | 4,194,304 |
pyintel_hw_cot_004412 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 240 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 240 pixels width $\times$ 240 pixels height = 57,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $240 \times 240 \times 2 = 115,200 \text{ bytes} = 112 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **T1-3S Wi-Fi Module**
| Constraint Parameter | Required Budget | Board Capability (`t1-3s`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 112 KB (240x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 96 KB | Supported with substantial overhead |
| **Tota... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 240 KB of conti... | t1-3s | BK7238 | Tuya Inc. | 262,144 | 1,083,136 |
pyintel_hw_cot_004413 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capabi... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 500 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (7V–28V DC wide input). Requires wide DC input step-down re... | ### Recommended Board: **WeMos WiFi and Bluetooth Battery**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `wemosbat` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, bluetooth, ethernet, c... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient inter... | wemosbat | ESP32 | WEMOS | 327,680 | 4,194,304 |
pyintel_hw_cot_004414 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 112 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Nordic nRF52840-DK (Adafruit BSP)**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `nrf52840_dk_adafruit` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `NRF52840` | Native dual-core/accelerated processing |
| **Operating Frequency** ... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 112 KB of unfragmented dynamic heap (accounting f... | nrf52840_dk_adafruit | NRF52840 | Nordic | 248,832 | 815,104 |
pyintel_hw_cot_004415 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **IoT Node LoRaWAN**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `sparkfun_iotnode_lorawanrp2350` | Verified Open Board Registry entry |
| **MCU Core** | `RP2350` | High-speed real-time core with hardware math |
| **Core Clock** | 150... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | sparkfun_iotnode_lorawanrp2350 | RP2350 | SparkFun | 524,288 | 16,777,216 |
pyintel_hw_cot_004416 | native_usb_emulation | I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable en... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Shrike-Lite**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `vicharak_shrike-lite` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2040` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HID/M... | <start_of_turn>user
I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY suppor... | vicharak_shrike-lite | RP2040 | Vicharak | 262,144 | 4,194,304 |
pyintel_hw_cot_004417 | native_usb_emulation | I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable en... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **EspinalLab ATMegaZero ESP32-S2**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `atmegazero_esp32s2` | Registered entry in Open Board Registry |
| **Microcontroller** | `ESP32S2` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Dri... | <start_of_turn>user
I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY suppor... | atmegazero_esp32s2 | ESP32S2 | EspinalLab | 327,680 | 16,777,216 |
pyintel_hw_cot_004418 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **CB3SE Wi-Fi Module**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Contr... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | cb3se | BK7231N | Tuya Inc. | 262,144 | 1,083,136 |
pyintel_hw_cot_004419 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capab... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 2000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (7V–28V DC wide input). Requires wide DC input step-down r... | ### Recommended Board: **VintLabs ESP32 Devkit**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `vintlabs-devkit-v1` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, bluetooth, ethernet, ca... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient inte... | vintlabs-devkit-v1 | ESP32 | VintLabs | 327,680 | 4,194,304 |
pyintel_hw_cot_004420 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 f... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 2000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (12V). Requires wide DC input step-down regulator or autom... | ### Recommended Board: **ST Nucleo L452RE**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `nucleo_l452re` | Registered open-hardware entry |
| **MCU Architecture** | `STM32L452RET6` | High-speed real-time core |
| **CAN Bus Interface** | can | Hardware frame filtration... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling ca... | nucleo_l452re | STM32L452RET6 | ST | 163,840 | 524,288 |
pyintel_hw_cot_004421 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 f... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 1000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (24V). Requires wide DC input step-down regulator or autom... | ### Recommended Board: **Digistump DigiX**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `digix` | Registered open-hardware entry |
| **MCU Architecture** | `AT91SAM3X8E` | High-speed real-time core |
| **CAN Bus Interface** | can | Hardware frame filtration & dedicate... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling ca... | digix | AT91SAM3X8E | Digistump | 98,304 | 524,288 |
pyintel_hw_cot_004422 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 44.1 kHz 16-bit mono produces $44.1 \times 10^3 \times 2 \approx 88,200 \text{ bytes/sec}$.
- **FFT Window Duration**: A 1024-point buffer represents $T_{window} = 1024 / (44.1 \times 10^3) \approx 23.22 \text{ ms}$.
- **Processin... | ### Recommended Board: **Plasma2350**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `pimoroni_plasma2350` | Verified Open Board Registry entry |
| **Processor Core** | `RP2350` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 150 MHz | FFT computes in $< 2 \text{ ms}$ (well be... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | pimoroni_plasma2350 | RP2350 | Pimoroni | 524,288 | 2,097,152 |
pyintel_hw_cot_004423 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 120 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **D-duino-32**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `d-duino-32` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient throughput fo... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 120 KB of unfragmented dynamic heap (accounting f... | d-duino-32 | ESP32 | DSTIKE | 327,680 | 4,194,304 |
pyintel_hw_cot_004424 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **STM32F415RG (128k RAM. 1024k Flash)**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `genericSTM32F415RG` | Verified Open Board Registry entry |
| **MCU Core** | `STM32F415RGT6` | High-speed real-time core with hardware math |
| **Core... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | genericSTM32F415RG | STM32F415RGT6 | Generic | 131,072 | 1,048,576 |
pyintel_hw_cot_004425 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 176 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 240 pixels width $\times$ 240 pixels height = 57,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $240 \times 240 \times 2 = 115,200 \text{ bytes} = 112 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **Bonfire on Arty, 256MB DRAM**
| Constraint Parameter | Required Budget | Board Capability (`arty-axi-dram`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 112 KB (240x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 32 KB | Supported with substantial ov... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 176 KB of conti... | arty-axi-dram | Bonfire Project | 268,435,456 | 32,768 | |
pyintel_hw_cot_004426 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 25 kHz PWM, each control cycle is $T = 1 / 25\text{ kHz} = 40.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Tiny2350**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `pimoroni_tiny2350` | Verified Open Board Registry entry |
| **MCU Core** | `RP2350` | High-speed real-time core with hardware math |
| **Core Clock** | 150 MHz | Completes FOC ... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | pimoroni_tiny2350 | RP2350 | Pimoroni | 524,288 | 4,194,304 |
pyintel_hw_cot_004427 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 40 kHz PWM, each control cycle is $T = 1 / 40\text{ kHz} = 25.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Black STM32F407VG**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `black_f407vg` | Verified Open Board Registry entry |
| **MCU Core** | `STM32F407VGT6` | High-speed real-time core with hardware math |
| **Core Clock** | 168 MHz | Com... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | black_f407vg | STM32F407VGT6 | ST | 131,072 | 524,288 |
pyintel_hw_cot_004428 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 214 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 320 pixels width $\times$ 240 pixels height = 76,800 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $320 \times 240 \times 2 = 153,600 \text{ bytes} = 150 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **WR1 Wi-Fi Module**
| Constraint Parameter | Required Budget | Board Capability (`wr1`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 150 KB (320x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 32 KB | Supported with substantial overhead |
| **Total SR... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 214 KB of conti... | wr1 | RTL8710BN | Tuya Inc. | 262,144 | 806,912 |
pyintel_hw_cot_004429 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S doub... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 44.1 kHz 16-bit mono produces $44.1 \times 10^3 \times 2 \approx 88,200 \text{ bytes/sec}$.
- **FFT Window Duration**: A 512-point buffer represents $T_{window} = 512 / (44.1 \times 10^3) \approx 11.61 \text{ ms}$.
- **Processing ... | ### Recommended Board: **DevEBox H743VITX**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `devebox_h743vitx` | Verified Open Board Registry entry |
| **Processor Core** | `STM32H743VIT6` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 480 MHz | FFT computes in $< 2 \text{ ms}... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support c... | devebox_h743vitx | STM32H743VIT6 | DevEBox | 524,288 | 2,097,152 |
pyintel_hw_cot_004430 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 136 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **ETBoard**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `etboard` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient throughput for TLS ... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 136 KB of unfragmented dynamic heap (accounting f... | etboard | ESP32 | ETBoard | 327,680 | 4,194,304 |
pyintel_hw_cot_004431 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 40 kHz PWM, each control cycle is $T = 1 / 40\text{ kHz} = 25.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Blues Swan R5**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `blues_swan_r5` | Verified Open Board Registry entry |
| **MCU Core** | `STM32L4R5ZIY6` | High-speed real-time core with hardware math |
| **Core Clock** | 120 MHz | Comple... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | blues_swan_r5 | STM32L4R5ZIY6 | Blues | 655,360 | 2,097,152 |
pyintel_hw_cot_004432 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **ST Nucleo L496ZG-P**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Contr... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | nucleo_l496zg_p | STM32L496ZGT6P | ST | 327,680 | 1,048,576 |
pyintel_hw_cot_004433 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 164 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Turta IoT Node**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `turta_iot_node` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient throu... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 164 KB of unfragmented dynamic heap (accounting f... | turta_iot_node | ESP32 | Turta | 327,680 | 4,194,304 |
pyintel_hw_cot_004434 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 148 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Smart Bee Motion**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `bee_motion` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32S2` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient throu... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 148 KB of unfragmented dynamic heap (accounting f... | bee_motion | ESP32S2 | Smart Bee | 327,680 | 4,194,304 |
pyintel_hw_cot_004435 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 40 kHz PWM, each control cycle is $T = 1 / 40\text{ kHz} = 25.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **RP2040 LoRa**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `waveshare_rp2040_lora` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** | 133 MHz | Complet... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | waveshare_rp2040_lora | RP2040 | Waveshare | 262,144 | 2,097,152 |
pyintel_hw_cot_004436 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 40 kHz PWM, each control cycle is $T = 1 / 40\text{ kHz} = 25.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **RP2 Nano**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `artronshop_rp2_nano` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** | 133 MHz | Completes FO... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | artronshop_rp2_nano | RP2040 | ArtronShop | 262,144 | 2,097,152 |
pyintel_hw_cot_004437 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 428 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **Quectel MC25 GSM Module**
| Constraint Parameter | Required Budget | Board Capability (`mc25`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 96 KB | Supported with substantial overhead |
| **... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 428 KB of conti... | mc25 | RDA8955 | Quectel Wireless Solutions Co., Ltd. | 1,040,384 | 589,824 |
pyintel_hw_cot_004438 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 148 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **TTGO T-OI PLUS RISC-V ESP32-C3**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `ttgo-t-oi-plus` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32C3` | Native dual-core/accelerated processing |
| **Operating Frequency** | 160 MHz ... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 148 KB of unfragmented dynamic heap (accounting f... | ttgo-t-oi-plus | ESP32C3 | TTGO | 327,680 | 4,194,304 |
pyintel_hw_cot_004439 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 176 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 240 pixels width $\times$ 240 pixels height = 57,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $240 \times 240 \times 2 = 115,200 \text{ bytes} = 112 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **Neoway N716 LTE Cat.1 Module**
| Constraint Parameter | Required Budget | Board Capability (`n716`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 112 KB (240x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 32 KB | Supported with substantial overhead |... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 176 KB of conti... | n716 | RDA8910 | Neoway Technology Co.Ltd. | 524,288 | 1,048,576 |
pyintel_hw_cot_004440 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 128 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Adafruit QT Py ESP32-S3 No PSRAM**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `adafruit_qtpy_esp32s3_nopsram` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32S3` | Native dual-core/accelerated processing |
| **Operating Frequ... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 128 KB of unfragmented dynamic heap (accounting f... | adafruit_qtpy_esp32s3_nopsram | ESP32S3 | Adafruit | 327,680 | 8,388,608 |
pyintel_hw_cot_004441 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 40 kHz PWM, each control cycle is $T = 1 / 40\text{ kHz} = 25.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **STM32F4Stamp F405**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `stm32f4stamp` | Verified Open Board Registry entry |
| **MCU Core** | `STM32F405RGT6` | High-speed real-time core with hardware math |
| **Core Clock** | 168 MHz | Com... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | stm32f4stamp | STM32F405RGT6 | Generic | 131,072 | 1,048,576 |
pyintel_hw_cot_004442 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S doub... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 96.0 kHz 16-bit mono produces $96.0 \times 10^3 \times 2 \approx 192,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 512-point buffer represents $T_{window} = 512 / (96.0 \times 10^3) \approx 5.33 \text{ ms}$.
- **Processing ... | ### Recommended Board: **u-blox C030-R410M IoT**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `ublox_c030_r410m` | Verified Open Board Registry entry |
| **Processor Core** | `STM32F437VG` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 180 MHz | FFT computes in $< 2 \text{ ... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support c... | ublox_c030_r410m | STM32F437VG | u-blox | 262,144 | 1,048,576 |
pyintel_hw_cot_004443 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 25 kHz PWM, each control cycle is $T = 1 / 25\text{ kHz} = 40.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **STM32F412RE (256k RAM. 512k Flash)**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `genericSTM32F412RE` | Verified Open Board Registry entry |
| **MCU Core** | `STM32F412RET6` | High-speed real-time core with hardware math |
| **Core ... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 25 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | genericSTM32F412RE | STM32F412RET6 | Generic | 262,144 | 524,288 |
pyintel_hw_cot_004444 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capabi... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 500 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (7V–28V DC wide input). Requires wide DC input step-down re... | ### Recommended Board: **Unexpected Maker TinyPICO**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `tinypico` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, bluetooth, ethernet, can | Ha... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient inter... | tinypico | ESP32 | Unexpected Maker | 327,680 | 4,194,304 |
pyintel_hw_cot_004445 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Raspberry Pi Pico**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `pico` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** | 133 MHz | Completes FOC loop... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | pico | RP2040 | Raspberry Pi | 270,336 | 2,097,152 |
pyintel_hw_cot_004446 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 364 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **Unexpected Maker PROS3**
| Constraint Parameter | Required Budget | Board Capability (`um_pros3`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 32 KB | Supported with substantial overhead |
|... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 364 KB of conti... | um_pros3 | ESP32S3 | Unexpected Maker | 327,680 | 16,777,216 |
pyintel_hw_cot_004447 | native_usb_emulation | I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoin... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **RP2040 Plus 16MB**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `waveshare_rp2040_plus_16mb` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2040` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | C... | <start_of_turn>user
I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting ... | waveshare_rp2040_plus_16mb | RP2040 | Waveshare | 262,144 | 16,777,216 |
pyintel_hw_cot_004448 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 136 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Adafruit QT Py ESP32**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `adafruit_qtpy_esp32` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Suffi... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 136 KB of unfragmented dynamic heap (accounting f... | adafruit_qtpy_esp32 | ESP32 | Adafruit | 327,680 | 8,388,608 |
pyintel_hw_cot_004449 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 246 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 320 pixels width $\times$ 240 pixels height = 76,800 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $320 \times 240 \times 2 = 153,600 \text{ bytes} = 150 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **MotorGo Mini 1 (ESP32-S3)**
| Constraint Parameter | Required Budget | Board Capability (`motorgo_mini_1`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 150 KB (320x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 64 KB | Supported with substantial ove... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 246 KB of conti... | motorgo_mini_1 | ESP32S3 | MotorGo | 327,680 | 4,194,304 |
pyintel_hw_cot_004450 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 f... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 2000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (24V). Requires wide DC input step-down regulator or autom... | ### Recommended Board: **Microduino Core ESP32**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `microduino-core-esp32` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, bluetooth, ethernet,... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling ca... | microduino-core-esp32 | ESP32 | Microduino | 327,680 | 4,194,304 |
pyintel_hw_cot_004451 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 428 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **Adafruit Metro ESP32-S3**
| Constraint Parameter | Required Budget | Board Capability (`adafruit_metro_esp32s3`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 96 KB | Supported with substanti... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 428 KB of conti... | adafruit_metro_esp32s3 | ESP32S3 | Adafruit | 327,680 | 16,777,216 |
pyintel_hw_cot_004452 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Arduino Nano RP2040 Connect**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `nanorp2040connect` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** | 133 M... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | nanorp2040connect | RP2040 | Arduino | 270,336 | 2,097,152 |
pyintel_hw_cot_004453 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 164 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Hornbill ESP32 Dev**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `hornbill32dev` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient th... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 164 KB of unfragmented dynamic heap (accounting f... | hornbill32dev | ESP32 | Hornbill | 327,680 | 4,194,304 |
pyintel_hw_cot_004454 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capab... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 1000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (7V–28V DC wide input). Requires wide DC input step-down r... | ### Recommended Board: **Teensy 4.0**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `teensy40` | Registered open-hardware entry |
| **MCU Architecture** | `IMXRT1062` | High-speed real-time core |
| **CAN Bus Interface** | can | Hardware frame filtration & dedicated ma... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient inte... | teensy40 | IMXRT1062 | Teensy | 524,288 | 2,031,616 |
pyintel_hw_cot_004455 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capabi... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 500 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (7V–28V DC wide input). Requires wide DC input step-down re... | ### Recommended Board: **OLIMEX ESP32-EVB**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `esp32-evb` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, bluetooth, ethernet, can | Hardware f... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient inter... | esp32-evb | ESP32 | OLIMEX | 327,680 | 4,194,304 |
pyintel_hw_cot_004456 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **RP2040 Plus 16MB**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `waveshare_rp2040_plus_16mb` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** | 133 MHz... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | waveshare_rp2040_plus_16mb | RP2040 | Waveshare | 262,144 | 16,777,216 |
pyintel_hw_cot_004457 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S doub... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 96.0 kHz 16-bit mono produces $96.0 \times 10^3 \times 2 \approx 192,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 512-point buffer represents $T_{window} = 512 / (96.0 \times 10^3) \approx 5.33 \text{ ms}$.
- **Processing ... | ### Recommended Board: **ST Nucleo L452RE**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `nucleo_l452re` | Verified Open Board Registry entry |
| **Processor Core** | `STM32L452RET6` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 80 MHz | FFT computes in $< 2 \text{ ms}$ (w... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support c... | nucleo_l452re | STM32L452RET6 | ST | 163,840 | 524,288 |
pyintel_hw_cot_004458 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 112 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **TTGO T1**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `ttgo-t1` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient throughput for TLS ... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 112 KB of unfragmented dynamic heap (accounting f... | ttgo-t1 | ESP32 | TTGO | 327,680 | 4,194,304 |
pyintel_hw_cot_004459 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S doub... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 48.0 kHz 16-bit mono produces $48.0 \times 10^3 \times 2 \approx 96,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 512-point buffer represents $T_{window} = 512 / (48.0 \times 10^3) \approx 10.67 \text{ ms}$.
- **Processing ... | ### Recommended Board: **ST Nucleo F411RE**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `nucleo_f411re` | Verified Open Board Registry entry |
| **Processor Core** | `STM32F411RET6` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 100 MHz | FFT computes in $< 2 \text{ ms}$ (... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support c... | nucleo_f411re | STM32F411RET6 | ST | 131,072 | 524,288 |
pyintel_hw_cot_004460 | native_usb_emulation | I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoin... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **senseBox MCU-S2 ESP32-S2**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `sensebox_mcu_esp32s2` | Registered entry in Open Board Registry |
| **Microcontroller** | `ESP32S2` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver ... | <start_of_turn>user
I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting ... | sensebox_mcu_esp32s2 | ESP32S2 | senseBox | 327,680 | 4,194,304 |
pyintel_hw_cot_004461 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 156 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Kinetic Dynamics Nebula S3**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `nebulas3` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32S3` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficie... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 156 KB of unfragmented dynamic heap (accounting f... | nebulas3 | ESP32S3 | Kinetic Dynamics | 327,680 | 4,194,304 |
pyintel_hw_cot_004462 | native_usb_emulation | I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable en... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **RP2040 LCD 0.96**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `waveshare_rp2040_lcd_0_96` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2040` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Cus... | <start_of_turn>user
I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY suppor... | waveshare_rp2040_lcd_0_96 | RP2040 | Waveshare | 262,144 | 2,097,152 |
pyintel_hw_cot_004463 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **VintLabs ESP32 Devkit**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Co... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | vintlabs-devkit-v1 | ESP32 | VintLabs | 327,680 | 4,194,304 |
pyintel_hw_cot_004464 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 104 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **M5Stack Core ESP32 16M**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `m5stack-core-esp32-16M` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | ... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 104 KB of unfragmented dynamic heap (accounting f... | m5stack-core-esp32-16M | ESP32 | M5Stack | 532,480 | 16,777,216 |
pyintel_hw_cot_004465 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 156 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Generic - RTL8710BX (4M/980k)**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `generic-rtl8710bx-4mb-980k` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `RTL8710BX` | Native dual-core/accelerated processing |
| **Operating Frequency... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 156 KB of unfragmented dynamic heap (accounting f... | generic-rtl8710bx-4mb-980k | RTL8710BX | Generic | 262,144 | 1,003,520 |
pyintel_hw_cot_004466 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 48.0 kHz 16-bit mono produces $48.0 \times 10^3 \times 2 \approx 96,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 2048-point buffer represents $T_{window} = 2048 / (48.0 \times 10^3) \approx 42.67 \text{ ms}$.
- **Processin... | ### Recommended Board: **ST Nucleo H745ZI-Q**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `nucleo_h745zi_q` | Verified Open Board Registry entry |
| **Processor Core** | `STM32H745ZIT6` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 480 MHz | FFT computes in $< 2 \text{ ms... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | nucleo_h745zi_q | STM32H745ZIT6 | ST | 524,288 | 1,048,576 |
pyintel_hw_cot_004467 | native_usb_emulation | I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable en... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Pico2XL**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `olimex_pico2xl` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2350` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HID/MIDI/CDC de... | <start_of_turn>user
I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY suppor... | olimex_pico2xl | RP2350 | Olimex | 524,288 | 2,097,152 |
pyintel_hw_cot_004468 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Challenger 2350 NB-IoT**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `challenger_2350_nbiot` | Verified Open Board Registry entry |
| **MCU Core** | `RP2350` | High-speed real-time core with hardware math |
| **Core Clock** | 150 MH... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | challenger_2350_nbiot | RP2350 | iLabs | 524,288 | 8,388,608 |
pyintel_hw_cot_004469 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 396 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **AI-Thinker A9G GSM Module**
| Constraint Parameter | Required Budget | Board Capability (`a9g`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 64 KB | Supported with substantial overhead |
| *... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 396 KB of conti... | a9g | RDA8955 | Ai-Thinker Co., Ltd. | 1,040,384 | 589,824 |
pyintel_hw_cot_004470 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 f... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 2000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (12V). Requires wide DC input step-down regulator or autom... | ### Recommended Board: **Adafruit Metro ESP32-S3**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `adafruit_metro_esp32s3` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32S3` | High-speed real-time core |
| **CAN Bus Interface** | bluetooth, wifi | Har... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling ca... | adafruit_metro_esp32s3 | ESP32S3 | Adafruit | 327,680 | 16,777,216 |
pyintel_hw_cot_004471 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 96.0 kHz 16-bit mono produces $96.0 \times 10^3 \times 2 \approx 192,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 2048-point buffer represents $T_{window} = 2048 / (96.0 \times 10^3) \approx 21.33 \text{ ms}$.
- **Processi... | ### Recommended Board: **Espressif ESP32 Dev Module**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `esp32dev` | Verified Open Board Registry entry |
| **Processor Core** | `ESP32` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 240 MHz | FFT computes in $< 2 \text{ ms}$ (wel... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | esp32dev | ESP32 | Espressif | 327,680 | 4,194,304 |
pyintel_hw_cot_004472 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 364 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **LilyGo T-Display-S3**
| Constraint Parameter | Required Budget | Board Capability (`lilygo-t-display-s3`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 32 KB | Supported with substantial over... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 364 KB of conti... | lilygo-t-display-s3 | ESP32S3 | LilyGo | 327,680 | 16,777,216 |
pyintel_hw_cot_004473 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **RP2350 Plus**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Controller**... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | waveshare_rp2350_plus | RP2350 | Waveshare | 524,288 | 4,194,304 |
pyintel_hw_cot_004474 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **Fishino Piranha ESP-32**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C C... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | piranha_esp32 | ESP32 | Fishino | 327,680 | 4,194,304 |
pyintel_hw_cot_004475 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 148 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **T102_V1.1**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `t102-v1.1` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `RTL8710BN` | Native dual-core/accelerated processing |
| **Operating Frequency** | 125 MHz | Sufficient throughput ... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 148 KB of unfragmented dynamic heap (accounting f... | t102-v1.1 | RTL8710BN | Unknown | 262,144 | 806,912 |
pyintel_hw_cot_004476 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **Unexpected Maker FeatherS2**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | um_feathers2 | ESP32S2 | Unexpected Maker | 327,680 | 16,777,216 |
pyintel_hw_cot_004477 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **Arduino Nano ESP32**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Contr... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | arduino_nano_esp32 | ESP32S3 | Arduino | 327,680 | 16,777,216 |
pyintel_hw_cot_004478 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 364 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **T103_V1.0**
| Constraint Parameter | Required Budget | Board Capability (`t103-v1.0`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 32 KB | Supported with substantial overhead |
| **Total SRA... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 364 KB of conti... | t103-v1.0 | RTL8710BX | Unknown | 262,144 | 806,912 |
pyintel_hw_cot_004479 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 96.0 kHz 16-bit mono produces $96.0 \times 10^3 \times 2 \approx 192,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 1024-point buffer represents $T_{window} = 1024 / (96.0 \times 10^3) \approx 10.67 \text{ ms}$.
- **Processi... | ### Recommended Board: **Aventen S3 Sync**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `aventen_s3_sync` | Verified Open Board Registry entry |
| **Processor Core** | `ESP32S3` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 240 MHz | FFT computes in $< 2 \text{ ms}$ (well ... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | aventen_s3_sync | ESP32S3 | Aventen | 327,680 | 16,777,216 |
pyintel_hw_cot_004480 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 172 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **M5Stack FIRE**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `m5stack-fire` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient throughpu... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 172 KB of unfragmented dynamic heap (accounting f... | m5stack-fire | ESP32 | M5Stack | 4,521,984 | 16,777,216 |
pyintel_hw_cot_004481 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 240 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 240 pixels width $\times$ 240 pixels height = 57,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $240 \times 240 \times 2 = 115,200 \text{ bytes} = 112 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **Unexpected Maker RMP**
| Constraint Parameter | Required Budget | Board Capability (`um_rmp`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 112 KB (240x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 96 KB | Supported with substantial overhead |
| **T... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 240 KB of conti... | um_rmp | ESP32S2 | Unexpected Maker | 327,680 | 4,194,304 |
pyintel_hw_cot_004482 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **Plasma2040**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Controller** ... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | pimoroni_plasma2040 | RP2040 | Pimoroni | 262,144 | 2,097,152 |
pyintel_hw_cot_004483 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 132 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **ESP32S3 CAM LCD**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `esp32s3camlcd` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32S3` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient thr... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 132 KB of unfragmented dynamic heap (accounting f... | esp32s3camlcd | ESP32S3 | Espressif | 327,680 | 8,388,608 |
pyintel_hw_cot_004484 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **ST Nucleo F746ZG**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `nucleo_f746zg` | Verified Open Board Registry entry |
| **MCU Core** | `STM32F746ZGT6` | High-speed real-time core with hardware math |
| **Core Clock** | 216 MHz | Com... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | nucleo_f746zg | STM32F746ZGT6 | ST | 327,680 | 1,048,576 |
pyintel_hw_cot_004485 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **STM32F103ZG (96k RAM. 1024k Flash)**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `genericSTM32F103ZG` | Verified Open Board Registry entry |
| **MCU Core** | `STM32F103ZGT6` | High-speed real-time core with hardware math |
| **Core ... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | genericSTM32F103ZG | STM32F103ZGT6 | Generic | 98,304 | 1,048,576 |
pyintel_hw_cot_004486 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Explorer**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `pimoroni_explorer` | Verified Open Board Registry entry |
| **MCU Core** | `RP2350` | High-speed real-time core with hardware math |
| **Core Clock** | 150 MHz | Completes FOC ... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | pimoroni_explorer | RP2350 | Pimoroni | 524,288 | 16,777,216 |
pyintel_hw_cot_004487 | native_usb_emulation | I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoin... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **RP2040 LCD 0.96**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `waveshare_rp2040_lcd_0_96` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2040` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Cus... | <start_of_turn>user
I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting ... | waveshare_rp2040_lcd_0_96 | RP2040 | Waveshare | 262,144 | 2,097,152 |
pyintel_hw_cot_004488 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 96 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 KB... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **T1-3S Wi-Fi Module**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `t1-3s` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `BK7238` | Native dual-core/accelerated processing |
| **Operating Frequency** | 120 MHz | Sufficient throughpu... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 96 KB of unfragmented dynamic heap (accounting fo... | t1-3s | BK7238 | Tuya Inc. | 262,144 | 1,083,136 |
pyintel_hw_cot_004489 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **WR2 Wi-Fi Module**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Control... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | wr2 | RTL8710BN | Tuya Inc. | 262,144 | 806,912 |
pyintel_hw_cot_004490 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 44.1 kHz 16-bit mono produces $44.1 \times 10^3 \times 2 \approx 88,200 \text{ bytes/sec}$.
- **FFT Window Duration**: A 2048-point buffer represents $T_{window} = 2048 / (44.1 \times 10^3) \approx 46.44 \text{ ms}$.
- **Processin... | ### Recommended Board: **ST STM32L4+ Discovery kit IoT node**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `disco_l4s5i_iot01a` | Verified Open Board Registry entry |
| **Processor Core** | `STM32L4S5VIT6` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 80 MHz | FFT computes... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | disco_l4s5i_iot01a | STM32L4S5VIT6 | ST | 655,360 | 2,097,152 |
pyintel_hw_cot_004491 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 f... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 1000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (24V). Requires wide DC input step-down regulator or autom... | ### Recommended Board: **ST Nucleo F446ZE**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `nucleo_f446ze` | Registered open-hardware entry |
| **MCU Architecture** | `STM32F446ZET6` | High-speed real-time core |
| **CAN Bus Interface** | can | Hardware frame filtration... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling ca... | nucleo_f446ze | STM32F446ZET6 | ST | 131,072 | 524,288 |
pyintel_hw_cot_004492 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **ST Nucleo L433RC-P**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Contr... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | nucleo_l433rc_p | STM32L433RC | ST | 65,536 | 262,144 |
pyintel_hw_cot_004493 | native_usb_emulation | I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoi... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Lilka v2**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `lilka_v2` | Registered entry in Open Board Registry |
| **Microcontroller** | `ESP32S3` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HID/MIDI/CDC descri... | <start_of_turn>user
I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting... | lilka_v2 | ESP32S3 | Anderson & friends | 327,680 | 16,777,216 |
pyintel_hw_cot_004494 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **3D Printer Controller**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Co... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | armed_v1 | STM32F407VET6 | Armed | 131,072 | 524,288 |
pyintel_hw_cot_004495 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 128 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **ProtoCentral HealthyPi 4**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `healthypi4` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 128 KB of unfragmented dynamic heap (accounting f... | healthypi4 | ESP32 | ProtoCentral | 327,680 | 4,194,304 |
pyintel_hw_cot_004496 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 136 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **TTGO T7 V1.4 Mini32**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `ttgo-t7-v14-mini32` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Suffici... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 136 KB of unfragmented dynamic heap (accounting f... | ttgo-t7-v14-mini32 | ESP32 | TTGO | 1,310,720 | 4,194,304 |
pyintel_hw_cot_004497 | native_usb_emulation | I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable en... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **MKS THR42**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `mksthr42` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2040` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HID/MIDI/CDC descri... | <start_of_turn>user
I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY suppor... | mksthr42 | RP2040 | Makerbase | 262,144 | 1,048,576 |
pyintel_hw_cot_004498 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 152 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Arduino Opta (M4 core)**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `opta_m4` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `STM32H747XIH6` | Native dual-core/accelerated processing |
| **Operating Frequency** | 480 MHz | Suffici... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 152 KB of unfragmented dynamic heap (accounting f... | opta_m4 | STM32H747XIH6 | Arduino | 294,248 | 1,048,576 |
pyintel_hw_cot_004499 | native_usb_emulation | I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoin... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Feather RP2040 DVI**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `adafruit_feather_dvi` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2040` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custo... | <start_of_turn>user
I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting ... | adafruit_feather_dvi | RP2040 | Adafruit | 262,144 | 8,388,608 |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.