id large_stringlengths 21 21 | domain large_stringclasses 7
values | instruction large_stringclasses 115
values | reasoning large_stringlengths 1.07k 5.05k | response large_stringlengths 677 1.11k | text large_stringlengths 2.31k 6.39k | target_board_id large_stringclasses 863
values | mcu large_stringclasses 201
values | vendor large_stringclasses 231
values | ram_bytes int64 2.05k 8.59B | rom_bytes int64 0 1.07B |
|---|---|---|---|---|---|---|---|---|---|---|
pyintel_hw_cot_007000 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 48.0 kHz 16-bit mono produces $48.0 \times 10^3 \times 2 \approx 96,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 1024-point buffer represents $T_{window} = 1024 / (48.0 \times 10^3) \approx 21.33 \text{ ms}$.
- **Processin... | ### Recommended Board: **PicoPlus2W**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `pimoroni_pico_plus_2w` | Verified Open Board Registry entry |
| **Processor Core** | `RP2350` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 150 MHz | FFT computes in $< 2 \text{ ms}$ (well ... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | pimoroni_pico_plus_2w | RP2350 | Pimoroni | 524,288 | 16,777,216 |
pyintel_hw_cot_007001 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 96 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 KB... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **AirM2M CORE ESP32C3**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `airm2m_core_esp32c3` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32C3` | Native dual-core/accelerated processing |
| **Operating Frequency** | 160 MHz | Suff... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 96 KB of unfragmented dynamic heap (accounting fo... | airm2m_core_esp32c3 | ESP32C3 | AirM2M | 327,680 | 4,194,304 |
pyintel_hw_cot_007002 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 f... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 2000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (24V). Requires wide DC input step-down regulator or autom... | ### Recommended Board: **Adafruit Feather ESP32-S2**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `adafruit_feather_esp32s2` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32S2` | High-speed real-time core |
| **CAN Bus Interface** | wifi | Hardware f... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling ca... | adafruit_feather_esp32s2 | ESP32S2 | Adafruit | 327,680 | 4,194,304 |
pyintel_hw_cot_007003 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S doub... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 96.0 kHz 16-bit mono produces $96.0 \times 10^3 \times 2 \approx 192,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 512-point buffer represents $T_{window} = 512 / (96.0 \times 10^3) \approx 5.33 \text{ ms}$.
- **Processing ... | ### Recommended Board: **WR2E Wi-Fi Module**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `wr2e` | Verified Open Board Registry entry |
| **Processor Core** | `RTL8710BN` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 125 MHz | FFT computes in $< 2 \text{ ms}$ (well below 5... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support c... | wr2e | RTL8710BN | Tuya Inc. | 262,144 | 806,912 |
pyintel_hw_cot_007004 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 f... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 1000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (12V). Requires wide DC input step-down regulator or autom... | ### Recommended Board: **Node32s**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `node32s` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, bluetooth, ethernet, can | Hardware frame filtra... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling ca... | node32s | ESP32 | Aiyarafun | 327,680 | 4,194,304 |
pyintel_hw_cot_007005 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 120 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **M5Stack-ATOM**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `m5stack-atom` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient throughpu... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 120 KB of unfragmented dynamic heap (accounting f... | m5stack-atom | ESP32 | M5Stack | 327,680 | 4,194,304 |
pyintel_hw_cot_007006 | native_usb_emulation | I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoi... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **SODAQ SFF**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `sodaq_sff` | Registered entry in Open Board Registry |
| **Microcontroller** | `SAMD21G18A` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HID/MIDI/CDC d... | <start_of_turn>user
I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting... | sodaq_sff | SAMD21G18A | SODAQ | 32,768 | 262,144 |
pyintel_hw_cot_007007 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **Adafruit MagTag 2.9**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Cont... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | adafruit_magtag29_esp32s2 | ESP32S2 | Adafruit | 327,680 | 4,194,304 |
pyintel_hw_cot_007008 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 96.0 kHz 16-bit mono produces $96.0 \times 10^3 \times 2 \approx 192,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 2048-point buffer represents $T_{window} = 2048 / (96.0 \times 10^3) \approx 21.33 \text{ ms}$.
- **Processi... | ### Recommended Board: **FlyBoard2040Core**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `flyboard2040_core` | Verified Open Board Registry entry |
| **Processor Core** | `RP2040` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 133 MHz | FFT computes in $< 2 \text{ ms}$ (wel... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | flyboard2040_core | RP2040 | DeRuiLab | 262,144 | 4,194,304 |
pyintel_hw_cot_007009 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 124 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **ST STM32L4+ Discovery kit IoT node**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `disco_l4s5i_iot01a` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `STM32L4S5VIT6` | Native dual-core/accelerated processing |
| **Operating Frequenc... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 124 KB of unfragmented dynamic heap (accounting f... | disco_l4s5i_iot01a | STM32L4S5VIT6 | ST | 655,360 | 2,097,152 |
pyintel_hw_cot_007010 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 148 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **T1-U Wi-Fi Module**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `t1-u` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `BK7238` | Native dual-core/accelerated processing |
| **Operating Frequency** | 120 MHz | Sufficient throughput ... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 148 KB of unfragmented dynamic heap (accounting f... | t1-u | BK7238 | Tuya Inc. | 262,144 | 1,083,136 |
pyintel_hw_cot_007011 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 44.1 kHz 16-bit mono produces $44.1 \times 10^3 \times 2 \approx 88,200 \text{ bytes/sec}$.
- **FFT Window Duration**: A 1024-point buffer represents $T_{window} = 1024 / (44.1 \times 10^3) \approx 23.22 \text{ ms}$.
- **Processin... | ### Recommended Board: **ST 32L476GDISCOVERY**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `disco_l476vg` | Verified Open Board Registry entry |
| **Processor Core** | `STM32L476VGT6` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 80 MHz | FFT computes in $< 2 \text{ ms}$ ... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | disco_l476vg | STM32L476VGT6 | ST | 131,072 | 1,048,576 |
pyintel_hw_cot_007012 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 fr... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 500 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (12V). Requires wide DC input step-down regulator or automo... | ### Recommended Board: **Espressif ESP-WROVER-KIT**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `esp-wrover-kit` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, bluetooth, ethernet, can... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling cap... | esp-wrover-kit | ESP32 | Espressif | 327,680 | 4,194,304 |
pyintel_hw_cot_007013 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S doub... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 96.0 kHz 16-bit mono produces $96.0 \times 10^3 \times 2 \approx 192,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 512-point buffer represents $T_{window} = 512 / (96.0 \times 10^3) \approx 5.33 \text{ ms}$.
- **Processing ... | ### Recommended Board: **Trueverit ESP32 Universal IoT Driver MK III**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `trueverit-iot-driver-mk3` | Verified Open Board Registry entry |
| **Processor Core** | `ESP32` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 240 MHz | FFT ... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support c... | trueverit-iot-driver-mk3 | ESP32 | Trueverit | 327,680 | 4,194,304 |
pyintel_hw_cot_007014 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 214 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 320 pixels width $\times$ 240 pixels height = 76,800 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $320 \times 240 \times 2 = 153,600 \text{ bytes} = 150 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **WR3LE Wi-Fi Module**
| Constraint Parameter | Required Budget | Board Capability (`wr3le`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 150 KB (320x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 32 KB | Supported with substantial overhead |
| **Tota... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 214 KB of conti... | wr3le | RTL8710BX | Tuya Inc. | 262,144 | 806,912 |
pyintel_hw_cot_007015 | native_usb_emulation | I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable en... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Feather RP2040 RFM**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `adafruit_feather_rfm` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2040` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custo... | <start_of_turn>user
I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY suppor... | adafruit_feather_rfm | RP2040 | Adafruit | 262,144 | 8,388,608 |
pyintel_hw_cot_007016 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 f... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 2000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (12V). Requires wide DC input step-down regulator or autom... | ### Recommended Board: **PYBStick 26 Pro**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `pybstick26_pro` | Registered open-hardware entry |
| **MCU Architecture** | `STM32F412RE` | High-speed real-time core |
| **CAN Bus Interface** | can | Hardware frame filtration &... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 12V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 2000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling ca... | pybstick26_pro | STM32F412RE | PYBStick | 262,144 | 524,288 |
pyintel_hw_cot_007017 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 172 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **oddWires IoT-Bus Proteus**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `iotbusproteus` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Suffici... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 172 KB of unfragmented dynamic heap (accounting f... | iotbusproteus | ESP32 | oddWires | 327,680 | 4,194,304 |
pyintel_hw_cot_007018 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S doub... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 96.0 kHz 16-bit mono produces $96.0 \times 10^3 \times 2 \approx 192,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 512-point buffer represents $T_{window} = 512 / (96.0 \times 10^3) \approx 5.33 \text{ ms}$.
- **Processing ... | ### Recommended Board: **Raspberry Pi 3 Model B**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `raspberrypi_3b` | Verified Open Board Registry entry |
| **Processor Core** | `BCM2837` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 1200 MHz | FFT computes in $< 2 \text{ ms}$... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support c... | raspberrypi_3b | BCM2837 | Raspberry Pi | 1,073,741,824 | 1,073,741,824 |
pyintel_hw_cot_007019 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 40 kHz PWM, each control cycle is $T = 1 / 40\text{ kHz} = 25.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Motion 2350 Pro**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `cytron_motion_2350_pro` | Verified Open Board Registry entry |
| **MCU Core** | `RP2350` | High-speed real-time core with hardware math |
| **Core Clock** | 150 MHz | Co... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | cytron_motion_2350_pro | RP2350 | Cytron | 524,288 | 2,097,152 |
pyintel_hw_cot_007020 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 144 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Quectel EC600U LTE Cat.1 Module**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `ec600u` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `RDA8910` | Native dual-core/accelerated processing |
| **Operating Frequency** | 500 MHz | Suffi... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 144 KB of unfragmented dynamic heap (accounting f... | ec600u | RDA8910 | Quectel Wireless Solutions Co., Ltd. | 524,288 | 1,048,576 |
pyintel_hw_cot_007021 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 f... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 1000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (24V). Requires wide DC input step-down regulator or autom... | ### Recommended Board: **Pycom LoPy4**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `lopy4` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, bluetooth, can, ethernet | Hardware frame filt... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling ca... | lopy4 | ESP32 | Pycom Ltd. | 1,310,720 | 4,194,304 |
pyintel_hw_cot_007022 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 128 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **TAMC Termod S3**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `tamc_termod_s3` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32S3` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient thr... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 128 KB of unfragmented dynamic heap (accounting f... | tamc_termod_s3 | ESP32S3 | TAMC | 327,680 | 8,388,608 |
pyintel_hw_cot_007023 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 112 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Quectel EC200U LTE Cat.1 Module**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `ec200u` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `RDA8910` | Native dual-core/accelerated processing |
| **Operating Frequency** | 500 MHz | Suffi... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 112 KB of unfragmented dynamic heap (accounting f... | ec200u | RDA8910 | Quectel Wireless Solutions Co., Ltd. | 524,288 | 1,048,576 |
pyintel_hw_cot_007024 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **ST Nucleo H753ZI**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `nucleo_h753zi` | Verified Open Board Registry entry |
| **MCU Core** | `STM32H753ZIT6` | High-speed real-time core with hardware math |
| **Core Clock** | 400 MHz | Com... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | nucleo_h753zi | STM32H753ZIT6 | ST | 524,288 | 2,097,152 |
pyintel_hw_cot_007025 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 132 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **chipKIT WiFire rev. C**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `chipkit_wifire_revc` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `32MZ2048EFG100` | Native dual-core/accelerated processing |
| **Operating Frequency** | 200 M... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 132 KB of unfragmented dynamic heap (accounting f... | chipkit_wifire_revc | 32MZ2048EFG100 | Digilent | 524,288 | 2,080,768 |
pyintel_hw_cot_007026 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 156 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **ElectronutLabs Blip**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `electronut_blip` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `NRF52840` | Native dual-core/accelerated processing |
| **Operating Frequency** | 64 MHz | Sufficie... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 156 KB of unfragmented dynamic heap (accounting f... | electronut_blip | NRF52840 | ElectronutLabs | 262,144 | 1,048,576 |
pyintel_hw_cot_007027 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **Namino Rosso**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Controller*... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | namino_rosso | ESP32S3 | MECT SRL | 327,680 | 4,194,304 |
pyintel_hw_cot_007028 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 152 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **AZ-Delivery ESP-32 Dev Kit C V4**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `az-delivery-devkit-v4` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 24... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 152 KB of unfragmented dynamic heap (accounting f... | az-delivery-devkit-v4 | ESP32 | AZ-Delivery | 532,480 | 4,194,304 |
pyintel_hw_cot_007029 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 176 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 240 pixels width $\times$ 240 pixels height = 57,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $240 \times 240 \times 2 = 115,200 \text{ bytes} = 112 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **RP2040 One**
| Constraint Parameter | Required Budget | Board Capability (`waveshare_rp2040_one`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 112 KB (240x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 32 KB | Supported with substantial overhead |
|... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 176 KB of conti... | waveshare_rp2040_one | RP2040 | Waveshare | 262,144 | 4,194,304 |
pyintel_hw_cot_007030 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 396 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **Bit-C PRO**
| Constraint Parameter | Required Budget | Board Capability (`nullbits_bit_c_pro`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 64 KB | Supported with substantial overhead |
| **... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 396 KB of conti... | nullbits_bit_c_pro | RP2040 | nullbits | 262,144 | 4,194,304 |
pyintel_hw_cot_007031 | native_usb_emulation | I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable en... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **RP2350 Plus**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `waveshare_rp2350_plus` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2350` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HID/... | <start_of_turn>user
I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY suppor... | waveshare_rp2350_plus | RP2350 | Waveshare | 524,288 | 4,194,304 |
pyintel_hw_cot_007032 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 156 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **BBC micro:bit V2**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `bbcmicrobit_v2` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `NRF52833` | Native dual-core/accelerated processing |
| **Operating Frequency** | 64 MHz | Sufficient t... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 156 KB of unfragmented dynamic heap (accounting f... | bbcmicrobit_v2 | NRF52833 | BBC | 131,072 | 524,288 |
pyintel_hw_cot_007033 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 fr... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 500 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (24V). Requires wide DC input step-down regulator or automo... | ### Recommended Board: **Digistump DigiX**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `digix` | Registered open-hardware entry |
| **MCU Architecture** | `AT91SAM3X8E` | High-speed real-time core |
| **CAN Bus Interface** | can | Hardware frame filtration & dedicate... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling cap... | digix | AT91SAM3X8E | Digistump | 98,304 | 524,288 |
pyintel_hw_cot_007034 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capability for 1,000 fr... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 500 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (24V). Requires wide DC input step-down regulator or automo... | ### Recommended Board: **NodeMCU-32S**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `nodemcu-32s` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, bluetooth, ethernet, can | Hardware fram... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 24V rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling cap... | nodemcu-32s | ESP32 | NodeMCU | 327,680 | 4,194,304 |
pyintel_hw_cot_007035 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **M5Stamp-Pico**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Controller*... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | m5stamp-pico | ESP32 | M5Stack | 327,680 | 4,194,304 |
pyintel_hw_cot_007036 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 172 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Generic - BK7238 (Tuya T1)**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `generic-bk7238-tuya` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `BK7238` | Native dual-core/accelerated processing |
| **Operating Frequency** | 120 MHz ... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 172 KB of unfragmented dynamic heap (accounting f... | generic-bk7238-tuya | BK7238 | Generic | 262,144 | 1,083,136 |
pyintel_hw_cot_007037 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S doub... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 48.0 kHz 16-bit mono produces $48.0 \times 10^3 \times 2 \approx 96,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 512-point buffer represents $T_{window} = 512 / (48.0 \times 10^3) \approx 10.67 \text{ ms}$.
- **Processing ... | ### Recommended Board: **BW12**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `bw12` | Verified Open Board Registry entry |
| **Processor Core** | `RTL8710BX` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 62.5 MHz | FFT computes in $< 2 \text{ ms}$ (well below 10.7 ms frame... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support c... | bw12 | RTL8710BX | Ai-Thinker Co., Ltd. | 262,144 | 479,232 |
pyintel_hw_cot_007038 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 112 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **WEMOS LOLIN D32**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `lolin_d32` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient throughpu... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 112 KB of unfragmented dynamic heap (accounting f... | lolin_d32 | ESP32 | WEMOS | 327,680 | 4,194,304 |
pyintel_hw_cot_007039 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 96.0 kHz 16-bit mono produces $96.0 \times 10^3 \times 2 \approx 192,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 2048-point buffer represents $T_{window} = 2048 / (96.0 \times 10^3) \approx 21.33 \text{ ms}$.
- **Processi... | ### Recommended Board: **Sipeed MF1 MF1**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `sipeed-MF1` | Verified Open Board Registry entry |
| **Processor Core** | `K210` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 400 MHz | FFT computes in $< 2 \text{ ms}$ (well below 21.... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | sipeed-MF1 | K210 | Sipeed | 6,291,456 | 16,777,216 |
pyintel_hw_cot_007040 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 240 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 240 pixels width $\times$ 240 pixels height = 57,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $240 \times 240 \times 2 = 115,200 \text{ bytes} = 112 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **Feather RP2040 CAN**
| Constraint Parameter | Required Budget | Board Capability (`adafruit_feather_can`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 112 KB (240x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 96 KB | Supported with substantial over... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 240 KB of conti... | adafruit_feather_can | RP2040 | Adafruit | 262,144 | 8,388,608 |
pyintel_hw_cot_007041 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **3DP001V1 Evaluation board for 3D printer**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Iso... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | st3dp001_eval | STM32F401VET6 | ST | 98,304 | 524,288 |
pyintel_hw_cot_007042 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 180 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **M5Stack-ATOM**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `m5stack-atom` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient throughpu... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 180 KB of unfragmented dynamic heap (accounting f... | m5stack-atom | ESP32 | M5Stack | 327,680 | 4,194,304 |
pyintel_hw_cot_007043 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **STM32F413RG (320k RAM. 1024k Flash)**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | genericSTM32F413RG | STM32F413RGT6 | Generic | 327,680 | 1,048,576 |
pyintel_hw_cot_007044 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capab... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 1000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (7V–28V DC wide input). Requires wide DC input step-down r... | ### Recommended Board: **ST Nucleo F746ZG**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `nucleo_f746zg` | Registered open-hardware entry |
| **MCU Architecture** | `STM32F746ZGT6` | High-speed real-time core |
| **CAN Bus Interface** | can, ethernet | Hardware frame ... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient inte... | nucleo_f746zg | STM32F746ZGT6 | ST | 327,680 | 1,048,576 |
pyintel_hw_cot_007045 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 120 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Maxim Health Sensor Platform**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `max32620hsp` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `MAX32620` | Native dual-core/accelerated processing |
| **Operating Frequency** | 96 MHz | Suf... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 120 KB of unfragmented dynamic heap (accounting f... | max32620hsp | MAX32620 | Maxim | 262,144 | 2,097,152 |
pyintel_hw_cot_007046 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 40 kHz PWM, each control cycle is $T = 1 / 40\text{ kHz} = 25.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Marble Pico**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `groundstudio_marble_pico` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** | 133 MHz | Comp... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | groundstudio_marble_pico | RP2040 | GroundStudio | 262,144 | 8,388,608 |
pyintel_hw_cot_007047 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 144 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **LSC LMA35 BK7231T**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `lsc-lma35-t` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `BK7231T` | Native dual-core/accelerated processing |
| **Operating Frequency** | 120 MHz | Sufficient thr... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 144 KB of unfragmented dynamic heap (accounting f... | lsc-lma35-t | BK7231T | Unknown | 262,144 | 1,083,136 |
pyintel_hw_cot_007048 | native_usb_emulation | I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable en... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **RYMCU ESP32-S3-DevKitC-1-N8R2 (8 MB QD, 2 MB PSRAM)**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `rymcu-esp32-s3-devkitc-1` | Registered entry in Open Board Registry |
| **Microcontroller** | `ESP32S3` | Direct native USB 2.0 FS silicon |
| **USB Sta... | <start_of_turn>user
I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY suppor... | rymcu-esp32-s3-devkitc-1 | ESP32S3 | RYMCU | 327,680 | 8,388,608 |
pyintel_hw_cot_007049 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 40 kHz PWM, each control cycle is $T = 1 / 40\text{ kHz} = 25.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **3D Printer Controller**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `armed_v1` | Verified Open Board Registry entry |
| **MCU Core** | `STM32F407VET6` | High-speed real-time core with hardware math |
| **Core Clock** | 168 MHz | Com... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | armed_v1 | STM32F407VET6 | Armed | 131,072 | 524,288 |
pyintel_hw_cot_007050 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 44.1 kHz 16-bit mono produces $44.1 \times 10^3 \times 2 \approx 88,200 \text{ bytes/sec}$.
- **FFT Window Duration**: A 1024-point buffer represents $T_{window} = 1024 / (44.1 \times 10^3) \approx 23.22 \text{ ms}$.
- **Processin... | ### Recommended Board: **Namino Arancio**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `namino_arancio` | Verified Open Board Registry entry |
| **Processor Core** | `ESP32S3` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 240 MHz | FFT computes in $< 2 \text{ ms}$ (well be... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | namino_arancio | ESP32S3 | MECT SRL | 327,680 | 4,194,304 |
pyintel_hw_cot_007051 | native_usb_emulation | I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoi... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **LowPowerLab CurrentRanger**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `current_ranger` | Registered entry in Open Board Registry |
| **Microcontroller** | `SAMD21G18A` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | ... | <start_of_turn>user
I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting... | current_ranger | SAMD21G18A | LowPowerLab | 32,768 | 262,144 |
pyintel_hw_cot_007052 | native_usb_emulation | I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoi... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **RP2350 Plus**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `waveshare_rp2350_plus` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2350` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HID/... | <start_of_turn>user
I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting... | waveshare_rp2350_plus | RP2350 | Waveshare | 524,288 | 4,194,304 |
pyintel_hw_cot_007053 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **SLSTK3701A Giant Gecko S1**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | efm32gg11_stk3701 | EFM32GG11B820F2048GL192 | Silicon Labs | 524,288 | 2,097,152 |
pyintel_hw_cot_007054 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 112 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **P-Nucleo WB55RG**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `nucleo_wb55rg_p` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `STM32WB55RG` | Native dual-core/accelerated processing |
| **Operating Frequency** | 64 MHz | Sufficien... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 112 KB of unfragmented dynamic heap (accounting f... | nucleo_wb55rg_p | STM32WB55RG | ST | 196,608 | 524,288 |
pyintel_hw_cot_007055 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 176 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 240 pixels width $\times$ 240 pixels height = 57,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $240 \times 240 \times 2 = 115,200 \text{ bytes} = 112 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **T1-2S Wi-Fi Module**
| Constraint Parameter | Required Budget | Board Capability (`t1-2s`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 112 KB (240x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 32 KB | Supported with substantial overhead |
| **Tota... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 176 KB of conti... | t1-2s | BK7238 | Tuya Inc. | 262,144 | 1,083,136 |
pyintel_hw_cot_007056 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 112 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Blinker WiFiduino32S3**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `wifiduino32s3` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32S3` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficie... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 112 KB of unfragmented dynamic heap (accounting f... | wifiduino32s3 | ESP32S3 | Blinker | 327,680 | 8,388,608 |
pyintel_hw_cot_007057 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **STM32F103RD (64k RAM. 384k Flash)**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) ... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | genericSTM32F103RD | STM32F103RDT6 | Generic | 65,536 | 393,216 |
pyintel_hw_cot_007058 | native_usb_emulation | I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoin... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **ProMicro RP2350**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `sparkfun_promicrorp2350` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2350` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custo... | <start_of_turn>user
I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting ... | sparkfun_promicrorp2350 | RP2350 | SparkFun | 524,288 | 16,777,216 |
pyintel_hw_cot_007059 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S doub... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 48.0 kHz 16-bit mono produces $48.0 \times 10^3 \times 2 \approx 96,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 512-point buffer represents $T_{window} = 512 / (48.0 \times 10^3) \approx 10.67 \text{ ms}$.
- **Processing ... | ### Recommended Board: **Seeed Arch Max**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `seeedArchMax` | Verified Open Board Registry entry |
| **Processor Core** | `STM32F407VET6` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 168 MHz | FFT computes in $< 2 \text{ ms}$ (wel... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support c... | seeedArchMax | STM32F407VET6 | SeeedStudio | 196,608 | 524,288 |
pyintel_hw_cot_007060 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 140 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **RYMCU ESP32-S3-DevKitC-1-N8R2 (8 MB QD, 2 MB PSRAM)**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `rymcu-esp32-s3-devkitc-1` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32S3` | Native dual-core/accelerated processing |
| **O... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 140 KB of unfragmented dynamic heap (accounting f... | rymcu-esp32-s3-devkitc-1 | ESP32S3 | RYMCU | 327,680 | 8,388,608 |
pyintel_hw_cot_007061 | native_usb_emulation | I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoin... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **KB2040**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `adafruit_kb2040` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2040` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HID/MIDI/CDC de... | <start_of_turn>user
I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting ... | adafruit_kb2040 | RP2040 | Adafruit | 262,144 | 8,388,608 |
pyintel_hw_cot_007062 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 44.1 kHz 16-bit mono produces $44.1 \times 10^3 \times 2 \approx 88,200 \text{ bytes/sec}$.
- **FFT Window Duration**: A 2048-point buffer represents $T_{window} = 2048 / (44.1 \times 10^3) \approx 46.44 \text{ ms}$.
- **Processin... | ### Recommended Board: **ST 32F746GDISCOVERY**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `disco_f746ng` | Verified Open Board Registry entry |
| **Processor Core** | `STM32F746NGH6` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 216 MHz | FFT computes in $< 2 \text{ ms}$... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | disco_f746ng | STM32F746NGH6 | ST | 327,680 | 1,048,576 |
pyintel_hw_cot_007063 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 156 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **Generic - BK7231T (Tuya)**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `generic-bk7231t-qfn32-tuya` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `BK7231T` | Native dual-core/accelerated processing |
| **Operating Frequency** | 12... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 156 KB of unfragmented dynamic heap (accounting f... | generic-bk7231t-qfn32-tuya | BK7231T | Generic | 262,144 | 1,083,136 |
pyintel_hw_cot_007064 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S doub... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 48.0 kHz 16-bit mono produces $48.0 \times 10^3 \times 2 \approx 96,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 512-point buffer represents $T_{window} = 512 / (48.0 \times 10^3) \approx 10.67 \text{ ms}$.
- **Processing ... | ### Recommended Board: **ST Nucleo F412ZG**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `nucleo_f412zg` | Verified Open Board Registry entry |
| **Processor Core** | `STM32F412ZGT6` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 100 MHz | FFT computes in $< 2 \text{ ms}$ (... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 48.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support c... | nucleo_f412zg | STM32F412ZGT6 | ST | 262,144 | 1,048,576 |
pyintel_hw_cot_007065 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 364 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **WeAct Studio MiniSTM32H743VITX**
| Constraint Parameter | Required Budget | Board Capability (`weact_mini_h743vitx`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 32 KB | Supported with subst... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 364 KB of conti... | weact_mini_h743vitx | STM32H743VIT6 | WeAct Studio | 524,288 | 2,097,152 |
pyintel_hw_cot_007066 | native_usb_emulation | I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoin... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **SparkFun 9DoF Razor IMU M0**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `sparkfun_samd21_9dof` | Registered entry in Open Board Registry |
| **Microcontroller** | `SAMD21G18A` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Dr... | <start_of_turn>user
I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting ... | sparkfun_samd21_9dof | SAMD21G18A | SparkFun | 32,768 | 262,144 |
pyintel_hw_cot_007067 | native_usb_emulation | I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoi... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **RP2040 LCD 0.96**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `waveshare_rp2040_lcd_0_96` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2040` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Cus... | <start_of_turn>user
I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting... | waveshare_rp2040_lcd_0_96 | RP2040 | Waveshare | 262,144 | 2,097,152 |
pyintel_hw_cot_007068 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **Arduino Nicla Vision**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Con... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | nicla_vision | STM32H747XIH6 | Arduino | 523,624 | 786,432 |
pyintel_hw_cot_007069 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 40 kHz PWM, each control cycle is $T = 1 / 40\text{ kHz} = 25.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **MTS Dragonfly**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `mts_dragonfly_f411re` | Verified Open Board Registry entry |
| **MCU Core** | `STM32F411RET6` | High-speed real-time core with hardware math |
| **Core Clock** | 100 MHz |... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | mts_dragonfly_f411re | STM32F411RET6 | MultiTech | 131,072 | 524,288 |
pyintel_hw_cot_007070 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 428 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **chipKIT WiFire rev. C**
| Constraint Parameter | Required Budget | Board Capability (`chipkit_wifire_revc`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 96 KB | Supported with substantial ov... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 428 KB of conti... | chipkit_wifire_revc | 32MZ2048EFG100 | Digilent | 524,288 | 2,080,768 |
pyintel_hw_cot_007071 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **96Boards Neonkey**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `b96b_aerocore2` | Verified Open Board Registry entry |
| **MCU Core** | `STM32F427VIT6` | High-speed real-time core with hardware math |
| **Core Clock** | 168 MHz | Co... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | b96b_aerocore2 | STM32F427VIT6 | 96Boards | 262,144 | 2,091,752 |
pyintel_hw_cot_007072 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 148 KB of unfragmented dynamic heap (accounting for RTOS kernel ~16 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **RYMCU ESP32-S3-DevKitC-1-N8R2 (8 MB QD, 2 MB PSRAM)**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `rymcu-esp32-s3-devkitc-1` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32S3` | Native dual-core/accelerated processing |
| **O... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 148 KB of unfragmented dynamic heap (accounting f... | rymcu-esp32-s3-devkitc-1 | ESP32S3 | RYMCU | 327,680 | 8,388,608 |
pyintel_hw_cot_007073 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capab... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 1000 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (7V–28V DC wide input). Requires wide DC input step-down r... | ### Recommended Board: **ETBoard**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `etboard` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32` | High-speed real-time core |
| **CAN Bus Interface** | wifi, bluetooth, ethernet, can | Hardware frame filtra... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 1000 kbps. We require a board with hardware CAN controller support, sufficient inte... | etboard | ESP32 | ETBoard | 327,680 | 4,194,304 |
pyintel_hw_cot_007074 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 128 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **M5Stack FIRE**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `m5stack-fire` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient throughpu... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 128 KB of unfragmented dynamic heap (accounting f... | m5stack-fire | ESP32 | M5Stack | 4,521,984 | 16,777,216 |
pyintel_hw_cot_007075 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Challenger 2040 NFC**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `challenger_2040_nfc` | Verified Open Board Registry entry |
| **MCU Core** | `RP2040` | High-speed real-time core with hardware math |
| **Core Clock** | 133 MHz | C... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | challenger_2040_nfc | RP2040 | iLabs | 262,144 | 8,388,608 |
pyintel_hw_cot_007076 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 208 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 240 pixels width $\times$ 240 pixels height = 57,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $240 \times 240 \times 2 = 115,200 \text{ bytes} = 112 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **Smart Bee S3**
| Constraint Parameter | Required Budget | Board Capability (`bee_s3`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 112 KB (240x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 64 KB | Supported with substantial overhead |
| **Total SRA... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 240x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 208 KB of conti... | bee_s3 | ESP32S3 | Smart Bee | 327,680 | 8,388,608 |
pyintel_hw_cot_007077 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capabi... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 500 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (7V–28V DC wide input). Requires wide DC input step-down re... | ### Recommended Board: **ST Nucleo F446ZE**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `nucleo_f446ze` | Registered open-hardware entry |
| **MCU Architecture** | `STM32F446ZET6` | High-speed real-time core |
| **CAN Bus Interface** | can | Hardware frame filtration... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient inter... | nucleo_f446ze | STM32F446ZET6 | ST | 131,072 | 524,288 |
pyintel_hw_cot_007078 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 428 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **Freenove ESP32-S3 WROOM N8R8 (8MB Flash / 8MB PSRAM)**
| Constraint Parameter | Required Budget | Board Capability (`freenove_esp32_s3_wroom`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 96... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 428 KB of conti... | freenove_esp32_s3_wroom | ESP32S3 | Freenove | 327,680 | 8,388,608 |
pyintel_hw_cot_007079 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **STM32F4Stamp F405**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `stm32f4stamp` | Verified Open Board Registry entry |
| **MCU Core** | `STM32F405RGT6` | High-speed real-time core with hardware math |
| **Core Clock** | 168 MHz | Com... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | stm32f4stamp | STM32F405RGT6 | Generic | 131,072 | 1,048,576 |
pyintel_hw_cot_007080 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 246 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 320 pixels width $\times$ 240 pixels height = 76,800 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $320 \times 240 \times 2 = 153,600 \text{ bytes} = 150 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **Maker Nano RP2040**
| Constraint Parameter | Required Budget | Board Capability (`cytron_maker_nano_rp2040`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 150 KB (320x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 64 KB | Supported with substantial o... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 246 KB of conti... | cytron_maker_nano_rp2040 | RP2040 | Cytron | 262,144 | 2,097,152 |
pyintel_hw_cot_007081 | native_usb_emulation | I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable en... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **RP2 Nano**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `artronshop_rp2_nano` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2040` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom HID/MIDI/... | <start_of_turn>user
I am designing a hardware USB MIDI controller with low-jitter serial streaming. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY suppor... | artronshop_rp2_nano | RP2040 | ArtronShop | 262,144 | 2,097,152 |
pyintel_hw_cot_007082 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **PYBStick 26 Pro**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Controll... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | pybstick26_pro | STM32F412RE | PYBStick | 262,144 | 524,288 |
pyintel_hw_cot_007083 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 96.0 kHz 16-bit mono produces $96.0 \times 10^3 \times 2 \approx 192,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 2048-point buffer represents $T_{window} = 2048 / (96.0 \times 10^3) \approx 21.33 \text{ ms}$.
- **Processi... | ### Recommended Board: **STM32F103VG (96k RAM. 1024k Flash)**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `genericSTM32F103VG` | Verified Open Board Registry entry |
| **Processor Core** | `STM32F103VGT6` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 72 MHz | FFT computes... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | genericSTM32F103VG | STM32F103VGT6 | Generic | 98,304 | 1,048,576 |
pyintel_hw_cot_007084 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 128 KB of unfragmented dynamic heap (accounting for RTOS kernel ~24 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **ETBoard**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `etboard` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `ESP32` | Native dual-core/accelerated processing |
| **Operating Frequency** | 240 MHz | Sufficient throughput for TLS ... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 128 KB of unfragmented dynamic heap (accounting f... | etboard | ESP32 | ETBoard | 327,680 | 4,194,304 |
pyintel_hw_cot_007085 | automotive_industrial_can | We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient interrupt handling capabi... | 1. **Constraint Analysis**:
- **Bus Protocol**: Hardware CAN / CAN-FD peripheral is required. Bitrate target is 500 kbps with deterministic acceptance filtering.
- **Power Rail**: Automotive power bus exhibits high ripple and load-dump voltage transients (7V–28V DC wide input). Requires wide DC input step-down re... | ### Recommended Board: **Adafruit Feather ESP32-S3 No PSRAM**
| Parameter | Specification | Functional Advantage |
| :--- | :--- | :--- |
| **Registry ID** | `adafruit_feather_esp32s3_nopsram` | Registered open-hardware entry |
| **MCU Architecture** | `ESP32S3` | High-speed real-time core |
| **CAN Bus Interface** | ... | <start_of_turn>user
We are engineering a sub-assembly node for an automotive chassis telemetry bus operating on a 7V–28V DC wide input rail. The module must communicate with the vehicle engine management system over CAN 2.0B / CAN-FD at 500 kbps. We require a board with hardware CAN controller support, sufficient inter... | adafruit_feather_esp32s3_nopsram | ESP32S3 | Adafruit | 327,680 | 8,388,608 |
pyintel_hw_cot_007086 | native_usb_emulation | I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoin... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **Challenger 2040 LoRa**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `challenger_2040_lora` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2040` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Cus... | <start_of_turn>user
I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting ... | challenger_2040_lora | RP2040 | iLabs | 262,144 | 8,388,608 |
pyintel_hw_cot_007087 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 428 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 480 pixels width $\times$ 320 pixels height = 153,600 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $480 \times 320 \times 2 = 307,200 \text{ bytes} = 300 \text{ KB}$.
- **LVGL UI Heap ... | ### Recommended Board: **Arty A7-100: Artix-7 FPGA Development Board**
| Constraint Parameter | Required Budget | Board Capability (`artix7_100t`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 300 KB (480x320 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 96 KB | Supported with ... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 480x320 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 428 KB of conti... | artix7_100t | C-CLASS | Xilinx | 134,217,728 | 0 |
pyintel_hw_cot_007088 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **IoT Node LoRaWAN**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Control... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | sparkfun_iotnode_lorawanrp2350 | RP2350 | SparkFun | 524,288 | 16,777,216 |
pyintel_hw_cot_007089 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S doub... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 44.1 kHz 16-bit mono produces $44.1 \times 10^3 \times 2 \approx 88,200 \text{ bytes/sec}$.
- **FFT Window Duration**: A 512-point buffer represents $T_{window} = 512 / (44.1 \times 10^3) \approx 11.61 \text{ ms}$.
- **Processing ... | ### Recommended Board: **MKR Sharky**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `mkr_sharky` | Verified Open Board Registry entry |
| **Processor Core** | `STM32WB55CG` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 64 MHz | FFT computes in $< 2 \text{ ms}$ (well below 1... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 512-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support c... | mkr_sharky | STM32WB55CG | Midatronics | 196,608 | 524,288 |
pyintel_hw_cot_007090 | display_framebuffer_gui | I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 246 KB of contiguous RAM without ca... | 1. **Mathematical Memory Budget Calculation**:
- **Display Dimensions**: 320 pixels width $\times$ 240 pixels height = 76,800 pixels.
- **Color Depth**: RGB565 = 16 bits = 2 bytes per pixel.
- **Single Framebuffer Size**: $320 \times 240 \times 2 = 153,600 \text{ bytes} = 150 \text{ KB}$.
- **LVGL UI Heap &... | ### Recommended Board: **Aceinna OpenIMU 330ZA**
| Constraint Parameter | Required Budget | Board Capability (`OpenRTK`) |
| :--- | :--- | :--- |
| **Framebuffer Allocation** | 150 KB (320x240 @ 16-bpp RGB565) | Easily allocated in internal SRAM |
| **LVGL GUI Heap** | 64 KB | Supported with substantial overhead |
| *... | <start_of_turn>user
I am building a handheld medical diagnostic device requiring a 320x240 color TFT display running in 16-bit RGB565 color format with the LVGL graphics library. The application requires full single-buffer rendering (or partial dual-buffering) and dynamic GUI widgets, demanding at least 246 KB of conti... | OpenRTK | STM32F469IG | Aceinna | 393,216 | 1,048,576 |
pyintel_hw_cot_007091 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 96.0 kHz 16-bit mono produces $96.0 \times 10^3 \times 2 \approx 192,000 \text{ bytes/sec}$.
- **FFT Window Duration**: A 1024-point buffer represents $T_{window} = 1024 / (96.0 \times 10^3) \approx 10.67 \text{ ms}$.
- **Processi... | ### Recommended Board: **SEGGER IP Switch Board**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `segger_ip_switch` | Verified Open Board Registry entry |
| **Processor Core** | `MK66FN2M0VMD18` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 180 MHz | FFT computes in $< 2 \te... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 1024-point complex Fast Fourier Transforms (FFT) at 96.0 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | segger_ip_switch | MK66FN2M0VMD18 | SEGGER | 262,144 | 2,097,152 |
pyintel_hw_cot_007092 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **PicoPlus2W**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Controller** ... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | pimoroni_pico_plus_2w | RP2350 | Pimoroni | 524,288 | 16,777,216 |
pyintel_hw_cot_007093 | native_usb_emulation | I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoi... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **MacroPad RP2040**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `adafruit_macropad2040` | Registered entry in Open Board Registry |
| **Microcontroller** | `RP2040` | Direct native USB 2.0 FS silicon |
| **USB Stack** | TinyUSB / Native Driver | Custom ... | <start_of_turn>user
I am designing a hardware Custom USB CDC ACM + WebUSB instrument interface. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting... | adafruit_macropad2040 | RP2040 | Adafruit | 262,144 | 8,388,608 |
pyintel_hw_cot_007094 | edge_audio_dsp | I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support circular DMA I2S dou... | 1. **Mathematical DSP & Throughput Budget**:
- **Audio Throughput**: Sampling at 44.1 kHz 16-bit mono produces $44.1 \times 10^3 \times 2 \approx 88,200 \text{ bytes/sec}$.
- **FFT Window Duration**: A 2048-point buffer represents $T_{window} = 2048 / (44.1 \times 10^3) \approx 46.44 \text{ ms}$.
- **Processin... | ### Recommended Board: **Pico2XXL**
| DSP Parameter | Value | Advantage |
| :--- | :--- | :--- |
| **Board ID** | `olimex_pico2xxl` | Verified Open Board Registry entry |
| **Processor Core** | `RP2350` | Hardware FPU & DSP SIMD extensions |
| **Clock Speed** | 150 MHz | FFT computes in $< 2 \text{ ms}$ (well below 46... | <start_of_turn>user
I am building an embedded real-time audio analysis module capturing acoustic emissions via an I2S MEMS microphone. The firmware must compute continuous 2048-point complex Fast Fourier Transforms (FFT) at 44.1 kHz sampling rate with CMSIS-DSP SIMD acceleration or hardware FPU. The board must support ... | olimex_pico2xxl | RP2350 | Olimex | 524,288 | 16,777,216 |
pyintel_hw_cot_007095 | battery_iot | I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 156 KB of unfragmented dynamic heap (accounting for RTOS kernel ~32 K... | 1. **Constraint Decomposition & Mathematical Budgets**:
- **Power Rail & Voltage**: 3.7V LiPo battery cell requires onboard 3.3V LDO regulator with low quiescent current. Logic level must be strictly 3.3V.
- **Network Stack**: Onboard 2.4 GHz WiFi or BLE transceiver is mandatory.
- **SRAM Sizing Formula**: Req... | ### Recommended Board: **WR3N Wi-Fi Module**
| Specification | Value | Justification |
| :--- | :--- | :--- |
| **Board ID** | `wr3n` | Verified entry in Open Board Registry |
| **Microcontroller (MCU)** | `RTL8710BN` | Native dual-core/accelerated processing |
| **Operating Frequency** | 125 MHz | Sufficient throughp... | <start_of_turn>user
I am designing an edge IoT environmental telemetry node powered by a 3.7V LiPo battery. The device must connect to cloud infrastructure over TLS 1.3 (MQTT over secure sockets) using onboard WiFi or BLE. The application runs an RTOS requiring at least 156 KB of unfragmented dynamic heap (accounting f... | wr3n | RTL8710BN | Tuya Inc. | 262,144 | 806,912 |
pyintel_hw_cot_007096 | native_usb_emulation | I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting programmable endpoin... | 1. **Constraint Breakdown**:
- **USB Silicon Architecture**: Must feature on-chip native USB 2.0 PHY with programmable DP/DM lines.
- **Driver Stack**: Must support raw USB endpoint configuration (TinyUSB or native USB device peripheral) for custom descriptor enumeration.
- **Protocol Rejection**: USB-UART bri... | ### Recommended Board: **4D Systems GEN4-ESP32 16MB (ESP32S3-R8N16)**
| Requirement | Specification | Verification |
| :--- | :--- | :--- |
| **Board ID** | `4d_systems_esp32s3_gen4_r8n16` | Registered entry in Open Board Registry |
| **Microcontroller** | `ESP32S3` | Direct native USB 2.0 FS silicon |
| **USB Stack**... | <start_of_turn>user
I am designing a hardware USB HID Macro Keyboard & Mouse composite device. The device must plug directly into a host PC and enumerate natively without requiring an external USB-to-UART bridge IC (such as CH340 or CP2102). The microcontroller must have an integrated USB 2.0 Full-Speed PHY supporting ... | 4d_systems_esp32s3_gen4_r8n16 | ESP32S3 | 4D Systems | 327,680 | 16,777,216 |
pyintel_hw_cot_007097 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 40 kHz PWM, each control cycle is $T = 1 / 40\text{ kHz} = 25.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **ST Nucleo G0B1RE**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `nucleo_g0b1re` | Verified Open Board Registry entry |
| **MCU Core** | `STM32G0B1RET6` | High-speed real-time core with hardware math |
| **Core Clock** | 64 MHz | Comp... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 40 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | nucleo_g0b1re | STM32G0B1RET6 | ST | 147,456 | 524,288 |
pyintel_hw_cot_007098 | multi_bus_sensor_fusion | I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitting NMEA strings at 1... | 1. **Bus Contention & Channel Breakdown**:
- **SPI Channel 0**: Dedicated exclusively to high-rate IMU polling (1 kHz loop, 10 MHz SPI clock).
- **SPI Channel 1**: Dedicated to MicroSD / Flash logging (large blocking write blocks must NOT hold up the IMU bus).
- **I2C Channel**: Dedicated 400 kHz Fast-Mode for... | ### Recommended Board: **RP2040 DevKit**
| Bus Interface | Peripheral Channel | Assigned Sensor |
| :--- | :--- | :--- |
| **SPI Controller 0** | Dedicated Hardware SPI0 | High-Rate 6-Axis IMU (1 kHz sampling) |
| **SPI Controller 1** | Dedicated Hardware SPI1 | MicroSD Blackbox Logging (Isolated) |
| **I2C Controller... | <start_of_turn>user
I am building an autonomous aerial vehicle telemetry hub. The board must interface simultaneously with:
1. A 6-axis IMU (MPU6050 / ICM-42688) polled at 1 kHz over high-speed SPI.
2. A barometric pressure sensor (BMP390) and I2C magnetometer polled over I2C at 400 kHz.
3. A GNSS/GPS module transmitti... | upesy_rp2040_devkit | RP2040 | uPesy | 262,144 | 2,097,152 |
pyintel_hw_cot_007099 | robotics_foc_motion | I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM center-alignment to read ... | 1. **Timing & Math Budget**:
- **Loop Period**: At 20 kHz PWM, each control cycle is $T = 1 / 20\text{ kHz} = 50.0\,\mu\text{s}$.
- **Calculations per Cycle**: Clarke and Park transformations, PI current controllers, and Space Vector Modulation (SVM) require $\approx 800\text{--}1,500$ CPU cycles.
- **Clock Re... | ### Recommended Board: **Armstrap Eagle 2048**
| Architectural Feature | Specification | Role in FOC Algorithm |
| :--- | :--- | :--- |
| **Board ID** | `armstrap_eagle2048` | Verified Open Board Registry entry |
| **MCU Core** | `STM32F427VIT6` | High-speed real-time core with hardware math |
| **Core Clock** | 168 M... | <start_of_turn>user
I am building a precision robotic joint controller executing Field Oriented Control (FOC) for a brushless DC (BLDC) motor. The control loop operates at 20 kHz PWM frequency with 3-phase complementary outputs and dead-time insertion. I require fast dual/triple ADC sampling synchronized with PWM cente... | armstrap_eagle2048 | STM32F427VIT6 | Armstrap | 262,144 | 2,091,752 |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.