Daily Papers

Robotic ultrasound couples a high-rate contact-force loop with slower, delayed image feedback, so image-guided ultrasound probe rotation can perturb contact force before the resulting image response is observed. We derive a closed-form orientation-rate limit that bounds the modeled rotation-induced estimated-force excursion over a finite horizon while accounting for disturbance rejection by the fast force loop. The limit depends on local contact stiffness, force-loop gains, a conservative rotation-to-force gain bound, the excursion budget, and the prediction horizon. We implement this model in a dual-rate controller with timestamp-based delay reconstruction and joint-torque-based force estimation, and evaluate it on a curved gelatin phantom using paired controller comparisons and component ablations. Relative to unconstrained image guidance, the proposed rate-limited controller reduced first-second root-mean-square (RMS) estimated-force error by 0.40 N while increasing cue-convergence time by 0.94 s. A fixed rate cap near the analytically predicted ceiling produced no resolvable difference in force error and converged 0.32 s faster, indicating that the principal practical value of the model is the rate-design rule rather than online prediction. Delay reconstruction had no resolvable effect at the tested latency. A single-subject popliteal scan demonstrated feasibility, although the image cue was noise-limited on heterogeneous tissue.

Handheld data collection systems, such as the Universal Manipulation Interface (UMI), enable scalable data collection across diverse environments but only capture observed actions rather than the desired actions executed by a robot controller. In contrast, teleoperation captures desired actions directly, but is prohibitively time-consuming to collect. We revisit this trade-off through the lens of action validity across task phases. We observe that handheld trajectories provide valid supervision in tolerant, free-space phases, but lack dynamic feasibility in contact-sensitive phases, where tracking observed trajectories at high stiffness produces large, unsafe contact forces. We study the interaction between these two supervision types for contact-rich manipulation and find that training policies that combine handheld data with a small number of targeted teleoperated demonstrations provide an efficient hybrid strategy. Specifically, rather than teleoperating the entire task, we only collect partial teleoperated demonstrations for task segments where base handheld policies fail. However, naively mixing handheld and teleoperated phase-specific data yields worse performance than training on handheld data alone. To address this mismatch between observed and desired supervision, we propose Bi-modal Routing for Imitation Data via Gated Experts (BRIDGE), a mixture of diffusion policy experts that routes between specialist task phase heads conditioned on the current robot state. Notably, our approach enables task-phase specific use of desired actions during contact sensitive segments and improves success rates over handheld-only baselines by up to 36.7% across three contact-rich manipulation tasks.

Ensuring safety in reinforcement learning (RL)-based robotic systems is a critical challenge, especially in contact-rich tasks within unstructured environments. While the state-of-the-art safe RL approaches mitigate risks through safe exploration or high-level recovery mechanisms, they often overlook low-level execution safety, where reflexive responses to potential hazards are crucial. Similarly, variable impedance control (VIC) enhances safety by adjusting the robot's mechanical response, yet lacks a systematic way to adapt parameters, such as stiffness and damping throughout the task. In this paper, we propose Bresa, a Bio-inspired Reflexive Hierarchical Safe RL method inspired by biological reflexes. Our method decouples task learning from safety learning, incorporating a safety critic network that evaluates action risks and operates at a higher frequency than the task solver. Unlike existing recovery-based methods, our safety critic functions at a low-level control layer, allowing real-time intervention when unsafe conditions arise. The task-solving RL policy, running at a lower frequency, focuses on high-level planning (decision-making), while the safety critic ensures instantaneous safety corrections. We validate Bresa on multiple tasks including a contact-rich robotic task, demonstrating its reflexive ability to enhance safety, and adaptability in unforeseen dynamic environments. Our results show that Bresa outperforms the baseline, providing a robust and reflexive safety mechanism that bridges the gap between high-level planning and low-level execution. Real-world experiments and supplementary material are available at project website https://jack-sherman01.github.io/Bresa.

Humanoid parkour policies can traverse various terrains, but task completion may mask challenges of harsh landings, edge contacts, and unstable stance contacts. Humans naturally regulate foot-terrain interaction through tactile feedback, modulating contact compliance according to terrain stiffness. This highlights a key domain gap between humans and humanoid robots: the absence of rich tactile sensing in most humanoid systems. We address this problem with TactileStep, a deployable tactile learning framework that brings sole pressure sensing into humanoid locomotion control for softer touchdowns and more stable support. TactileStep aligns tactile simulation with the real pressure insole, allowing the policy to learn from the same contact features available on hardware. During training, we use tactile and motion cues to recognize different foot-contact phases and apply phase-aware rewards that encourage safer landing and more stable stance. Evaluated in simulation and on a Unitree G1 humanoid across diverse terrains, TactileStep reduces peak touchdown force by up to 48.8% and peak A-weighted impact noise by up to 30.1 dB over a strong perceptive baseline, while increasing stance contact area by up to 23.8%.

Existing methods for 3D tracking from monocular RGB videos predominantly consider articulated and rigid objects. Modelling dense non-rigid object deformations in this setting remained largely unaddressed so far, although such effects can improve the realism of the downstream applications such as AR/VR and avatar communications. This is due to the severe ill-posedness of the monocular view setting and the associated challenges. While it is possible to naively track multiple non-rigid objects independently using 3D templates or parametric 3D models, such an approach would suffer from multiple artefacts in the resulting 3D estimates such as depth ambiguity, unnatural intra-object collisions and missing or implausible deformations. Hence, this paper introduces the first method that addresses the fundamental challenges depicted above and that allows tracking human hands interacting with human faces in 3D from single monocular RGB videos. We model hands as articulated objects inducing non-rigid face deformations during an active interaction. Our method relies on a new hand-face motion and interaction capture dataset with realistic face deformations acquired with a markerless multi-view camera system. As a pivotal step in its creation, we process the reconstructed raw 3D shapes with position-based dynamics and an approach for non-uniform stiffness estimation of the head tissues, which results in plausible annotations of the surface deformations, hand-face contact regions and head-hand positions. At the core of our neural approach are a variational auto-encoder supplying the hand-face depth prior and modules that guide the 3D tracking by estimating the contacts and the deformations. Our final 3D hand and face reconstructions are realistic and more plausible compared to several baselines applicable in our setting, both quantitatively and qualitatively. https://vcai.mpi-inf.mpg.de/projects/Decaf

It has been difficult to accurately model the physics of the interaction between a robot and the objects it manipulates, including contact mechanics, coupled contact dynamics, deformations, stiffness and friction. We present RoboSimStudio (RSS), an interactive toolkit that makes choices of solver, contact model, and physical parameters explicit and editable, allowing both humans and coding agents to quickly create and iteratively refine simulations based on observed physical behavior. We implement RSS with the open Newton physics simulation system and describe experiments with human-guided real2sim using (1) visual evaluation, (2) force-feedback and (3) agentic Real2Sim2Real. Code, video and additional information can be found on the project website: https://robosimstudio.github.io

Rich contact perception is crucial for robotic manipulation, yet traditional tactile skins remain expensive and complex to integrate. This paper presents a scalable alternative: high-accuracy whole-body touch localization via vibro-acoustic sensing. By equipping a robotic hand with seven low-cost piezoelectric microphones and leveraging an Audio Spectrogram Transformer, we decode the vibrational signatures generated during physical interaction. Extensive evaluation across stationary and dynamic tasks reveals a localization error of under 5 mm in static conditions. Furthermore, our analysis highlights the distinct influence of material properties: stiff materials (e.g., metal) excel in impulse response localization due to sharp, high-bandwidth responses, whereas textured materials (e.g., wood) provide superior friction-based features for trajectory tracking. The system demonstrates robustness to the robot's own motion, maintaining effective tracking even during active operation. Our primary contribution is demonstrating that complex physical contact dynamics can be effectively decoded from simple vibrational signals, offering a viable pathway to widespread, affordable contact perception in robotics. To accelerate research, we provide our full datasets, models, and experimental setups as open-source resources.

Compliance is a useful parametrization of tactile information that humans often utilize in manipulation tasks. It can be used to inform low-level contact-rich actions or characterize objects at a high-level. In robotic manipulation, existing approaches to estimate compliance have struggled to generalize across object shape and material. Using camera-based tactile sensors, we present a novel approach to parametrize compliance through Young's modulus E. We evaluate our method over a novel dataset of 285 common objects, including a wide array of shapes and materials with Young's moduli ranging from 5.0 kPa to 250 GPa. Data is collected over automated parallel grasps of each object. Combining analytical and data-driven approaches, we develop a hybrid system using a multi-tower neural network to analyze a sequence of tactile images from grasping. This system is shown to estimate the Young's modulus of unseen objects within an order of magnitude at 74.2% accuracy across our dataset. This is a drastic improvement over a purely analytical baseline, which exhibits only 28.9% accuracy. Importantly, this estimation system performs irrespective of object geometry and demonstrates robustness across object materials. Thus, it could be applied in a general robotic manipulation setting to characterize unknown objects and inform decision-making, for instance to sort produce by ripeness.

Purpose: Six million people use crutches as mobile aids in the US. Rigid designs with no axial mobility limit sensory feedback and lead to secondary injury on the upper joints. Spring-loaded designs offer compliance but may compromise stability. We designed a biologically inspired tensegrity crutch with a compliant module aiming to achieve favorable mechanical properties. The terminal module was a pre-stressed self-tensile two-cell tensegrity structure. We compared the tensegrity crutch to commercial rigid and spring-loaded crutches in mechanical tests using axial loading, in overground straight and turning walking, and in participant experience. Methods: In human trials, healthy young adults (N=18) with no recent lower-body injury performed straight walking and turning trials at a comfortable self-selected pace. A knee blocker simulated unilateral injury of the dominant leg. After using each type of crutch, participants reported their perceived levels of effort, comfort, pain, stability, and usability. Results: Compared to the rigid design, both spring-loaded and tensegrity conditions reduced peak loading rates. The tensegrity design improved effort, comfort, pain, and usability. Spring-loaded crutches reduced perceived stability and walking speed. Conclusion: The biologically inspired tensegrity crutches were an overall improvement to existing designs. Simulations and mechanical testing suggest that nonlinear stiffness, ground-following, and force feedback are among the beneficial mechanical properties that underlie this improvement.

Safe yet stable grasping requires a robotic hand to apply sufficient force on the object to immobilize it while keeping it from getting damaged. Soft robotic hands have been proposed for safe grasping due to their passive compliance, but even such a hand can crush objects if the applied force is too high. Thus for safe grasping, regulating the grasping force is of uttermost importance even with soft hands. In this work, we present a force controlled soft hand and use it to achieve safe grasping. To this end, resistive force and bend sensors are integrated in a soft hand, and a data-driven calibration method is proposed to estimate contact interaction forces. Given the force readings, the pneumatic pressures are regulated using a proportional-integral controller to achieve desired force. The controller is experimentally evaluated and benchmarked by grasping easily deformable objects such as plastic and paper cups without neither dropping nor deforming them. Together, the results demonstrate that our force controlled soft hand can grasp deformable objects in a safe yet stable manner.

Dexterous interaction with articulated objects is important for household, assistive, and humanoid manipulation, where multi-finger hands can provide compliant contact patterns beyond parallel-jaw grasping. However, articulated-object manipulation differs from static-object manipulation: the target part cannot be directly actuated, and its motion must emerge through sustained physical hand--handle contact. This makes the transition from object-centric articulated generation to hand-driven dexterous hand--object interaction non-trivial, since geometric trajectory replay or open-loop execution does not model the contact dynamics required to move the articulated part. Moreover, policies trained only for task completion under fixed dynamics can overfit nominal contact loads, especially without tactile or force feedback, and may degrade when the contact load changes. To address these challenges, we present DragMesh-2, a contact-driven framework for dexterous interaction with articulated objects that extends articulated interaction from object-centric generation to hand-driven dexterous hand--object interaction, where articulated motion must arise through physical contact. We further propose PICA, a physically informed contact-aware training mechanism that injects physical signals into policy learning without tactile or force feedback, improving robustness and task success under changing contact loads. Finally, we conduct systematic evaluation across multiple damping conditions and articulated-object categories to study robustness under contact-load variation, and provide a pure-geometry dexterous interaction resource to support future loco-manipulation and humanoid hand--object interaction research. Across seven GAPartNet objects, DragMesh-2 achieves stronger robustness under contact-load variation than the compared methods while maintaining high task success across damping conditions.

Increased effort during use of the paretic arm and hand can provoke involuntary abnormal synergy patterns and amplify stiffness effects of muscle tone for individuals after stroke, which can add difficulty for user-controlled devices to assist hand movement during functional tasks. We study how volitional effort, exerted in an attempt to open or close the hand, affects resistance to robot-assisted movement at the finger level. We perform experiments with three chronic stroke survivors to measure changes in stiffness when the user is actively exerting effort to activate ipsilateral EMG-controlled robot-assisted hand movements, compared with when the fingers are passively stretched, as well as overall effects from sustained active engagement and use. Our results suggest that active engagement of the upper extremity increases muscle tone in the finger to a much greater degree than through passive-stretch or sustained exertion over time. Potential design implications of this work suggest that developers should anticipate higher levels of finger stiffness when relying on user-driven ipsilateral control methods for assistive or rehabilitative devices for stroke.

Contact-rich manipulation tasks with stiff frictional elements like connector insertion are difficult to model with rigid-body simulators. In this work, we propose a new approach for modeling these environments by learning a quasi-static contact force model instead of a full simulator. Using a feature vector that contains information about the configuration and control, we find a linear mapping adequately captures the relationship between this feature vector and the sensed contact forces. A novel Linear Model Learning (LML) algorithm is used to solve for the globally optimal mapping in real time without any matrix inversions, resulting in an algorithm that runs in nearly constant time on a GPU as the model size increases. We validate the proposed approach for connector insertion both in simulation and hardware experiments, where the learned model is combined with an optimization-based controller to achieve smooth insertions in the presence of misalignments and uncertainty. Our website featuring videos, code, and more materials is available at https://model-based-plugging.github.io/.

Robotic systems operating in unstructured environments require the ability to switch between compliant and rigid states to perform diverse tasks such as adaptive grasping, high-force manipulation, shape holding, and navigation in constrained spaces, among others. However, many existing variable stiffness solutions rely on complex actuation schemes, continuous input power, or monolithic designs, limiting their modularity and scalability. This paper presents the Programmable Locking Cell (PLC)-a modular, tendon-driven unit that achieves discrete stiffness modulation through mechanically interlocked joints actuated by cable tension. Each unit transitions between compliant and firm states via structural engagement, and the assembled system exhibits high stiffness variation-up to 950% per unit-without susceptibility to damage under high payload in the firm state. Multiple PLC units can be assembled into reconfigurable robotic structures with spatially programmable stiffness. We validate the design through two functional prototypes: (1) a variable-stiffness gripper capable of adaptive grasping, firm holding, and in-hand manipulation; and (2) a pipe-traversing robot composed of serial PLC units that achieves shape adaptability and stiffness control in confined environments. These results demonstrate the PLC as a scalable, structure-centric mechanism for programmable stiffness and motion, enabling robotic systems with reconfigurable morphology and task-adaptive interaction.

Contact often occurs without macroscopic surface deformation, such as during interaction with liquids, semi-liquids, or ultra-soft materials. However, most existing tactile sensors rely on deformation to infer contact, making such light-contact interactions difficult to perceive robustly. To address this, we present LightTact, a visual-tactile fingertip sensor that makes contact directly visible via a deformation-independent principle. LightTact features an ambient-blocking optical configuration that suppresses both external light and internal illumination at non-contact regions, while transmitting only the scattered light generated at true contacts. As a result, LightTact produces high-contrast raw images in which non-contact pixels remain near-black (mean gray value < 3) and contact pixels preserve the natural appearance of the contacting surface. Built on this, LightTact achieves accurate pixel-level contact segmentation that is robust to material properties, contact force, surface appearance, and environmental lighting. We further demonstrate that LightTact unlocks new robotic manipulation behaviors that require detection of extremely light contact, including water spreading, facial-cream dipping, and soft thin-film interaction. In addition, we show that LightTact's spatially aligned visual-tactile images can be directly interpreted by vision-language models.

Dexterous robot hands can receive useful motion intent from teleoperation or learned policies, but successful execution also depends on contact decisions that these commands rarely specify. We introduce DexFLEX, a contact-aware foundation controller that turns upstream fingertip-motion drafts into contact-consistent joint commands. Instead of treating a draft as a trajectory to copy, DexFLEX treats it as evidence about intent: from the current tactile-proprioceptive state, it proposes feasible short-horizon motion chunks, predicts their contact consequences, and selects the candidate that best follows the command while preserving future contact stability. At inference time, a simple Draft-Dream-Select procedure combines pure-prior proposals for recovery with draft-seeded proposals for responsiveness, then decodes the selected motion into executable joint-space targets. Across degraded-command simulation, real-world shared control, and visuomotor policy learning, the same trained controller improves robustness without retraining, increasing real-world teleoperation success from 29.2% to 78.3% and reaching 46.7% policy-learning success, 3.5 times direct joint-action prediction, and 1.56 times prior-only correction. Videos are available at dex-flex.github.io.

Accurate grasp force control is one of the key skills for ensuring successful and damage-free robotic grasping of objects. Although existing methods have conducted in-depth research on slip detection and grasping force planning, they often overlook the issue of adaptive tracking of the actual force to the target force when handling objects with different material properties. The optimal parameters of a force tracking controller are significantly influenced by the object's stiffness, and many adaptive force tracking algorithms rely on stiffness estimation. However, real-world objects often exhibit viscous, plastic, or other more complex nonlinear time-varying behaviors, and existing studies provide insufficient support for these materials in terms of stiffness definition and estimation. To address this, this paper introduces the concept of generalized stiffness, extending the definition of stiffness to nonlinear time-varying grasp system models, and proposes an online generalized stiffness estimator based on Long Short-Term Memory (LSTM) networks. Based on generalized stiffness, this paper proposes an adaptive parameter adjustment strategy using a PI controller as an example, enabling dynamic force tracking for objects with varying characteristics. Experimental results demonstrate that the proposed method achieves high precision and short probing time, while showing better adaptability to non-ideal objects compared to existing methods. The method effectively solves the problem of grasp force tracking in unknown, nonlinear, and time-varying grasp systems, demonstrating the generalization capability of our neural network and enhancing the robotic grasping ability in unstructured environments.

Joint contact forces govern implant longevity, cartilage health, and rehabilitation outcomes, shaping who develops osteoarthritis, who recovers well from joint replacement, and who benefits from biomechanical interventions. Yet they remain measurable only invasively, in a few dozen patients with instrumented implants. I present a physics-free pipeline to predict instantaneous 3D hip and knee contact forces from an uncalibrated monocular video: no markers, force plates, electromyography, subject-specific imaging, or musculoskeletal model. Parametric body meshes are recovered per frame, encoded as kinematic features, and decoded into forces by a transformer whose pose stream is adaptively modulated at every layer by body shape, joint, side, activity text, and self-supervised video tokens (V-JEPA 2), unifying hip and knee in a single model. Under leave-one-subject-out cross-validation across 26 patients and 25 activity categories from the in vivo OrthoLoad database, the pipeline matches the accuracy of subject-specific musculoskeletal simulations (0.32 pm 0.08 BW RMSE for hip; 0.23 pm 0.03 BW for knee) and resolves peak force changes smaller than those reported for gait retraining and osteoarthritis progression. Applied zero-shot to an independent instrumented cohort, it rivals or outperforms prior published methods. Even without curated activity labels, video features alone preserve accuracy and enable end-to-end inference on raw footage. Driven by the predictor, a generative motion prior produces biomechanically plausible variants with reduced peak loading, rediscovering strategies from the predictive simulation literature. This pipeline establishes uncalibrated monocular video as a viable modality for estimating joint loading, opening a path toward retrospective analysis of archived clinical recordings, primary-care screening, and at-home rehabilitation tracking.

The aim of the present work is to investigate the influence of the realistic model parameters on the equipartition of energy in a vibrofluidized system. To achieve this, a three-dimensional vertically vibrated granular system consisting of spherical particles is simulated using the discrete element method (DEM) using the open-source software LAMMPS. Interparticle and wall-particle interactions are determined using the linear-spring dashpot model. Simulations are performed for nearly perfectly smooth to nearly perfectly rough particles. Two different values for the ratio of the tangential to normal spring stiffness coefficient kappa (2/7 and 3/4) are chosen. Non-equipartition of energy between the translational and rotational modes is observed for all realistic values in the parametric range.

Contact-rich policies often fail because distinct physical states look alike yet require different actions. Cameras may not reveal whether a connector is aligned or fully seated, while many normal-only tactile sensors can miss the tangential interactions perpendicular to the grasping direction that distinguish these states. We ask whether a learning policy needs calibrated shear measurements, or only a repeatable observation that separates shear-dependent contact states. We introduce TacGooseBumps (TacGB), a passive domed film that mechanically encodes tangential loading as pattern changes in an existing sensor's pressure map. Tangential loading tilts each dome and redistributes pressure across its footprint; an end-to-end policy consumes the resulting maps without added electronics, force reconstruction, or taxel-level dome alignment. Across four imitation-learning tasks and two data-collection pipelines, TacGB improves goal attainment, efficiency, and contact quality: insertion success increases by up to 36 percentage points, and successful insertions are completed faster, while fragile-object placement becomes gentler and drawing becomes more continuous and straight. Signal, stage-wise, failure-mode, and trajectory analyses link these gains to contact regimes in which task-relevant tangential interactions are poorly resolved by vision and normal pressure alone. Together, these results show that shear need not be measured metrically to benefit robot learning; it can instead be mechanically encoded without changing the underlying tactile sensor or the policy's pressure-map input format.

Risk-aware planners score paths on uncertain elevation maps using the path cost's mean and standard deviation. Modeling rigid contact, however, requires computing a maximum over several uncertain cells. First-order propagation loses accuracy here by differentiating at only a single cell, while Monte Carlo sampling requires a full path evaluation per draw. We compute the moments of that contact maximum in closed form using Clark's pairwise recursion. By tracking each contact's covariance against the shared map cells, we propagate the smooth remainder using exact Gaussian quadratic-form identities. A contest-depth calibration, fitted once on two design traverses, closes the aggregate standard-deviation shortfall that remains. On 317 held-out rover path segments, scored against a Monte Carlo reference from the same belief, every pre-registered criterion was met. The corrected Clark fold cuts the median error of the mean from linearization's 2.3% to 0.19% and attains the lowest error in the conditional value at risk (CVaR) at the 90% level of every method tested. A benchmark plan costs just 5.5 microseconds on a GPU. These accuracy gains concentrate at contested contacts. While they seldom change which path is chosen on this terrain, the fold still selects the reference-best path in 98% of decisions against linearization's 93 to 96%. On a second dataset the mean transfers, though the risk number does not.

If human experience is any guide, operating effectively in unstructured environments -- like homes and offices -- requires robots to sense the forces during physical interaction. Yet, the lack of a versatile, accessible, and easily customizable tactile sensor has led to fragmented, sensor-specific solutions in robotic manipulation -- and in many cases, to force-unaware, sensorless approaches. With eFlesh, we bridge this gap by introducing a magnetic tactile sensor that is low-cost, easy to fabricate, and highly customizable. Building an eFlesh sensor requires only four components: a hobbyist 3D printer, off-the-shelf magnets (<$5), a CAD model of the desired shape, and a magnetometer circuit board. The sensor is constructed from tiled, parameterized microstructures, which allow for tuning the sensor's geometry and its mechanical response. We provide an open-source design tool that converts convex OBJ/STL files into 3D-printable STLs for fabrication. This modular design framework enables users to create application-specific sensors, and to adjust sensitivity depending on the task. Our sensor characterization experiments demonstrate the capabilities of eFlesh: contact localization RMSE of 0.5 mm, and force prediction RMSE of 0.27 N for normal force and 0.12 N for shear force. We also present a learned slip detection model that generalizes to unseen objects with 95% accuracy, and visuotactile control policies that improve manipulation performance by 40% over vision-only baselines -- achieving 91% average success rate for four precise tasks that require sub-mm accuracy for successful completion. All design files, code and the CAD-to-eFlesh STL conversion tool are open-sourced and available on https://e-flesh.com.

Contact-rich manipulation requires estimating forces, slip and contact geometry that can remain ambiguous in scene images. Optical tactile sensors provide both visual observations of the contact surface and mechanical measurements, yet learning from these signals raises two challenges: representing contact beyond appearance and transferring its benefits to a policy that does not require fingertip observations at deployment. We introduce HapticWAM, a world-action model that combines heterogeneous tactile encoding, structured contact prediction and teacher-student distillation. Its teacher encodes gel images together with deformation, shear, distributed forces, resultant wrench and derived contact state into a frozen video backbone. Rather than predicting tactile pixels alone, the model jointly generates actions and a contact package describing future events and mechanics. Anticipatory Contact Coupling uses the previously imagined package to condition attention, preserving a contact-related input when direct tactile observations are unavailable. Haptic-Imagination Distillation transfers both contact futures and action predictions to a student that retains the generative contact head but removes its fingertip input branches. On a real-world setup, across three contact-rich pick-and-place tasks, HapticWAM Student achieves a 77% per-task mean success rate (41 of 50 starts, 82% pooled), reaching 95% on one of the tasks, outperforming the evaluated teacher and baseline configurations.

Robotic grasping and surface exploration benefit from simultaneous measurement of normal and tangential forces and from surface information obtained through contact. Here, we present a compact magnetociliary tactile sensor (MagCilia) that combines a flexible magnetic-cilia structure with a Hall sensor for 3D force sensing. Quasi-static finite element analysis is used to investigate structural deformation and magnetic responses under multidirectional loading. To reconstruct forces from the coupled magnetic channels, we propose causal history fusion regression (CHFR), which combines current magnetic-field measurements with their recent changes. Five-fold cross-validation grouped by calibration record yields root-mean-square errors of 0.40, 0.57, and 0.69 N for Fx, Fy, and Fz, respectively, with corresponding coefficients of determination of 0.93, 0.90, and 0.92. Robotic experiments demonstrate tangential-force-guided gripper adjustment and multi-axis load monitoring under external perturbations. Frequency-domain features of the reconstructed forces distinguish six surface categories with 99.39% accuracy in three-fold cross-validation grouped by acquisition session. An online robotic demonstration additionally identifies all six tested surfaces. These results demonstrate 3D force reconstruction, grasping feedback, and surface recognition using a single compact tactile unit.

We introduce DIFFTACTILE, a physics-based differentiable tactile simulation system designed to enhance robotic manipulation with dense and physically accurate tactile feedback. In contrast to prior tactile simulators which primarily focus on manipulating rigid bodies and often rely on simplified approximations to model stress and deformations of materials in contact, DIFFTACTILE emphasizes physics-based contact modeling with high fidelity, supporting simulations of diverse contact modes and interactions with objects possessing a wide range of material properties. Our system incorporates several key components, including a Finite Element Method (FEM)-based soft body model for simulating the sensing elastomer, a multi-material simulator for modeling diverse object types (such as elastic, elastoplastic, cables) under manipulation, a penalty-based contact model for handling contact dynamics. The differentiable nature of our system facilitates gradient-based optimization for both 1) refining physical properties in simulation using real-world data, hence narrowing the sim-to-real gap and 2) efficient learning of tactile-assisted grasping and contact-rich manipulation skills. Additionally, we introduce a method to infer the optical response of our tactile sensor to contact using an efficient pixel-based neural module. We anticipate that DIFFTACTILE will serve as a useful platform for studying contact-rich manipulations, leveraging the benefits of dense tactile feedback and differentiable physics. Code and supplementary materials are available at the project website https://difftactile.github.io/.

The development of biophysical models for clinical applications is rapidly advancing in the research community, thanks to their predictive nature and their ability to assist the interpretation of clinical data. However, high-resolution and accurate multi-physics computational models are computationally expensive and their personalisation involves fine calibration of a large number of parameters, which may be space-dependent, challenging their clinical translation. In this work, we propose a new approach which relies on the combination of physics-informed neural networks (PINNs) with three-dimensional soft tissue nonlinear biomechanical models, capable of reconstructing displacement fields and estimating heterogeneous patient-specific biophysical properties. The proposed learning algorithm encodes information from a limited amount of displacement and, in some cases, strain data, that can be routinely acquired in the clinical setting, and combines it with the physics of the problem, represented by a mathematical model based on partial differential equations, to regularise the problem and improve its convergence properties. Several benchmarks are presented to show the accuracy and robustness of the proposed method and its great potential to enable the robust and effective identification of patient-specific, heterogeneous physical properties, s.a. tissue stiffness properties. In particular, we demonstrate the capability of the PINN to detect the presence, location and severity of scar tissue, which is beneficial to develop personalised simulation models for disease diagnosis, especially for cardiac applications.

The elastic response of mechanical, chemical, and biological systems is often modeled using a discrete arrangement of Hookean springs, either representing finite material elements or even the molecular bonds of a system. However, to date, there is no direct derivation of the relation between a general discrete spring network, with arbitrary geometry, and it's corresponding elastic continuum. Furthermore, understanding the network's mechanical response requires simulations that may be expensive computationally. Here we report a method to derive the exact elastic continuum model of any discrete network of springs, requiring network geometry and topology only. We identify and calculate the so-called "non-affine" displacements. Explicit comparison of our calculations to simulations of different crystalline and disordered configurations, shows we successfully capture the mechanics even of auxetic materials. Our method is valid for residually stressed systems with non-trivial geometries, and is an essential step in generalizing active stresses on such discrete systems. It is easily generalizable to other discrete models, and opens the possibility of a rational design of elastic systems.

In this paper, we tackle the problem of estimating 3D contact forces using vision-based tactile sensors. In particular, our goal is to estimate contact forces over a large range (up to 15 N) on any objects while generalizing across different vision-based tactile sensors. Thus, we collected a dataset of over 200K indentations using a robotic arm that pressed various indenters onto a GelSight Mini sensor mounted on a force sensor and then used the data to train a multi-head transformer for force regression. Strong generalization is achieved via accurate data collection and multi-objective optimization that leverages depth contact images. Despite being trained only on primitive shapes and textures, the regressor achieves a mean absolute error of 4\% on a dataset of unseen real-world objects. We further evaluate our approach's generalization capability to other GelSight mini and DIGIT sensors, and propose a reproducible calibration procedure for adapting the pre-trained model to other vision-based sensors. Furthermore, the method was evaluated on real-world tasks, including weighing objects and controlling the deformation of delicate objects, which relies on accurate force feedback. Project webpage: http://prg.cs.umd.edu/FeelAnyForce

Modeling the hand-object (HO) interaction not only requires estimation of the HO pose, but also pays attention to the contact due to their interaction. Significant progress has been made in estimating hand and object separately with deep learning methods, simultaneous HO pose estimation and contact modeling has not yet been fully explored. In this paper, we present an explicit contact representation namely Contact Potential Field (CPF), and a learning-fitting hybrid framework namely MIHO to Modeling the Interaction of Hand and Object. In CPF, we treat each contacting HO vertex pair as a spring-mass system. Hence the whole system forms a potential field with minimal elastic energy at the grasp position. Extensive experiments on the two commonly used benchmarks have demonstrated that our method can achieve state-of-the-art in several reconstruction metrics, and allow us to produce more physically plausible HO pose even when the ground-truth exhibits severe interpenetration or disjointedness. Our code is available at https://github.com/lixiny/CPF.

Humans are dexterous, but traditional data collection paradigms such as teleoperation, kinesthetic teaching, and wearable exoskeletons force humans to act through the robot embodiment, bottlenecking their dexterity. Retargeting can avoid this. However, existing methods purely translate kinematics and ignore the real-world contact dynamics essential for task success. We present CARD: Contact-Anchored Retargeting for Dexterous Manipulation, a simulator and object-free framework that retargets human demonstrations to robot actions by explicitly preserving contact force targets. CARD unifies human data sources including video, motion capture, and tactile gloves via a shared hand--contact representation and generates explicit contact force targets in addition to kinematics. To maintain these contact targets during hardware open-loop replay, CARD also introduces a tactile tracking controller. For video which does not contain an explicit tactile source, we present Vid-HACO, our video-to-contact model that sets a new state of the art. Across our video, glove, motion-capture data and the GRAB dataset, CARD maintains contact on 43--78% of contact frames, while kinematic and object-aware retargeting methods maintain contact on <10% and 22.5% of the frames respectively. Further, integrating our formulation into physics-based retargeting improves strict task success from 12\% to 32\% on GRAB dataset. Finally, we show that our tactile tracker is critical to reproduce demonstrated forces during hardware replay. These results establish that contact preservation via CARD is a scalable interface for transferring human dexterity to robots.

We introduce the task of Reconstructing Objects along Hand Interaction Timelines (ROHIT). We first define the Hand Interaction Timeline (HIT) from a rigid object's perspective. In a HIT, an object is first static relative to the scene, then is held in hand following contact, where its pose changes. This is usually followed by a firm grip during use, before it is released to be static again w.r.t. to the scene. We model these pose constraints over the HIT, and propose to propagate the object's pose along the HIT enabling superior reconstruction using our proposed Constrained Optimisation and Propagation (COP) framework. Importantly, we focus on timelines with stable grasps - i.e. where the hand is stably holding an object, effectively maintaining constant contact during use. This allows us to efficiently annotate, study, and evaluate object reconstruction in videos without 3D ground truth. We evaluate our proposed task, ROHIT, over two egocentric datasets, HOT3D and in-the-wild EPIC-Kitchens. In HOT3D, we curate 1.2K clips of stable grasps. In EPIC-Kitchens, we annotate 2.4K clips of stable grasps including 390 object instances across 9 categories from videos of daily interactions in 141 environments. Without 3D ground truth, we utilise 2D projection error to assess the reconstruction. Quantitatively, COP improves stable grasp reconstruction by 6.2-11.3% and HIT reconstruction by up to 24.5% with constrained pose propagation.

Many everyday tasks require controlling contact force as well as motion. On a humanoid, this force must often be coordinated across both hands and the whole body, and cannot be specified by kinematic trajectories alone. Therefore, we present FLORE, a framework for learning force-reactive humanoid loco-manipulation. We collect robot-free demonstrations using two force-sensing UMI-style handheld grippers for hand motion and contact wrenches, and wearable trackers for body motion. A force-reactive diffusion policy takes vision, proprioception, and measured wrenches as input, then predicts actions and per-hand force commands. A hybrid compliance whole-body controller with force tracking executes these commands while maintaining balance: an integral of the force error measured by real force/torque (F/T) sensors lets each hand track force accurately along the commanded direction and remain compliant along the others. In simulation, the controller tracks per-hand force commands of varied magnitude and direction, with little loss in whole-body motion accuracy. Across three contact-rich tasks on the robot, the force-reactive policy succeeds in 80% of rollouts, compared with 26.7% for a position-only policy trained on the same demonstrations and executed by the same controller. For more details, please visit our website: https://louis-leee.github.io/FLoRe/.

Physics simulation for contact-rich robotics is often bottlenecked by contact resolution: mainstream engines enforce non-penetration and Coulomb friction via complementarity constraints or constrained optimization, requiring per-step iterative solves whose cost grows superlinearly with contact density. We present ComFree-Sim, a GPU-parallelized analytical contact physics engine built on complementarity-free contact modeling. ComFree-Sim computes contact impulses in closed form via an impedance-style prediction--correction update in the dual cone of Coulomb friction. Contact computation decouples across contact pairs and becomes separable across cone facets, mapping naturally to GPU kernels and yielding near-linear runtime scaling with the number of contacts. We further extend the formulation to a unified 6D contact model capturing tangential, torsional, and rolling friction, and introduce a practical dual-cone impedance heuristic. ComFree-Sim is implemented in Warp and exposed through a MuJoCo-compatible interface as a drop-in backend alternative to MuJoCo Warp (MJWarp). Experiments benchmark penetration, friction behaviors, stability, and simulation runtime scaling against MJWarp, demonstrating near-linear scaling and 2--3 times higher throughput in dense contact scenes with comparable physical fidelity. We deploy ComFree-Sim in real-time MPC for in-hand dexterous manipulation on a real-world multi-fingered LEAP hand and in dynamics-aware motion retargeting, demonstrating that low-latency simulation yields higher closed-loop success rates and enables practical high-frequency control in contact-rich tasks.

In this paper, we address force-aware control and force distribution in robotic platforms with multi-fingered hands. Given a target goal and force estimates from tactile sensors, we design a controller that adapts the motion of the torso, arm, wrist, and fingers, redistributing forces to maintain stable contact with objects of varying mass distribution or unstable contacts. To estimate forces, we collect a dataset of tactile signals and ground-truth force measurements using five Xela magnetic sensors interacting with indenters, and train force estimators. We then introduce a model-based control scheme that minimizes the distance between the Center of Pressure (CoP) and the centroid of the fingertips contact polygon. Since our method relies on estimated forces rather than raw tactile signals, it has the potential to be applied to any sensor capable of force estimation. We validate our framework on a balancing task with five objects, achieving a 82.7% success rate, and further evaluate it in multi-object scenarios, achieving 80% accuracy. Code and data can be found here https://github.com/hsp-iit/multifingered-force-aware-control.

We address the problem of understanding when and why Vision-Language-Action models struggle with contact-rich manipulation tasks that require precise physical interaction. Prior work has primarily focused on addressing contact failures through force-augmented architectures and training-time regularizers, yet the root causes of these failures remain underexplored. We identify two distinct failure modes underlying this gap. Precision failures are rooted in a flow-matching policy training mismatch, and force failures arise from the distinctive structure of force signals. We address each failure mode with a targeted mechanism and combine them into FACT, which achieves 66% average success rate across five contact-rich tasks against 41% for the best prior baseline, in an evaluation spanning almost 2,500 real-world rollouts.

Many manipulation tasks require careful force modulation. With insufficient force the task may fail, while excessive force could cause damage. The high cost, bulky size and fragility of commercial force/torque (F/T) sensors have limited large-scale, force-aware policy learning. We introduce UMI-FT, a handheld data-collection platform that mounts compact, six-axis force/torque sensors on each finger, enabling finger-level wrench measurements alongside RGB, depth, and pose. Using the multimodal data collected from this device, we train an adaptive compliance policy that predicts position targets, grasp force, and stiffness for execution on standard compliance controllers. In evaluations on three contact-rich, force-sensitive tasks (whiteboard wiping, skewering zucchini, and lightbulb insertion), UMI-FT enables policies that reliably regulate external contact forces and internal grasp forces, outperforming baselines that lack compliance or force sensing. UMI-FT offers a scalable path to learning compliant manipulation from in-the-wild demonstrations. We open-source the hardware and software to facilitate broader adoption at:https://umi-ft.github.io/.

Touch contact and pressure are essential for understanding how humans interact with and manipulate objects, insights which can significantly benefit applications in mixed reality and robotics. However, estimating these interactions from an egocentric camera perspective is challenging, largely due to the lack of comprehensive datasets that provide both accurate hand poses on contacting surfaces and detailed annotations of pressure information. In this paper, we introduce EgoPressure, a novel egocentric dataset that captures detailed touch contact and pressure interactions. EgoPressure provides high-resolution pressure intensity annotations for each contact point and includes accurate hand pose meshes obtained through our proposed multi-view, sequence-based optimization method processing data from an 8-camera capture rig. Our dataset comprises 5 hours of recorded interactions from 21 participants captured simultaneously by one head-mounted and seven stationary Kinect cameras, which acquire RGB images and depth maps at 30 Hz. To support future research and benchmarking, we present several baseline models for estimating applied pressure on external surfaces from RGB images, with and without hand pose information. We further explore the joint estimation of the hand mesh and applied pressure. Our experiments demonstrate that pressure and hand pose are complementary for understanding hand-object interactions. ng of hand-object interactions in AR/VR and robotics research. Project page: https://yiming-zhao.github.io/EgoPressure/.

In this paper, we address the problem of tactile sim-to-real policy transfer for contact-rich tasks. Existing methods primarily focus on vision-based sensors and emphasize image rendering quality while providing overly simplistic models of force and shear. Consequently, these models exhibit a large sim-to-real gap for many dexterous tasks. Here, we present HydroShear, a non-holonomic hydroelastic tactile simulator that advances the state-of-the-art by modeling: a) stick-slip transitions, b) path-dependent force and shear build up, and c) full SE(3) object-sensor interactions. HydroShear extends hydroelastic contact models using Signed Distance Functions (SDFs) to track the displacements of the on-surface points of an indenter during physical interaction with the sensor membrane. Our approach generates physics-based, computationally efficient force fields from arbitrary watertight geometries while remaining agnostic to the underlying physics engine. In experiments with GelSight Minis, HydroShear more faithfully reproduces real tactile shear compared to existing methods. This fidelity enables zero-shot sim-to-real transfer of reinforcement learning policies across four tasks: peg insertion, bin packing, book shelving for insertion, and drawer pulling for fine gripper control under slip. Our method achieves a 93% average success rate, outperforming policies trained on tactile images (34%) and alternative shear simulation methods (58%-61%).

Contact-rich manipulation depends on applying the correct grasp forces throughout the manipulation task, especially when handling fragile or deformable objects. Most existing imitation learning approaches often treat visuotactile feedback only as an additional observation, leaving applied forces as an uncontrolled consequence of gripper commands. In this work, we present Force-Aware Robotic Manipulation (FARM), an imitation learning framework that integrates high-dimensional tactile data to infer tactile-conditioned force signals, which in turn define a matching force-based action space. We collect human demonstrations using a modified version of the handheld Universal Manipulation Interface (UMI) gripper that integrates a GelSight Mini visual tactile sensor. For deploying the learned policies, we developed an actuated variant of the UMI gripper with geometry matching our handheld version. During policy rollouts, the proposed FARM diffusion policy jointly predicts robot pose, grip width, and grip force. FARM outperforms several baselines across three tasks with distinct force requirements -- high-force, low-force, and dynamic force adaptation -- demonstrating the advantages of its two key components: leveraging force-grounded, high-dimensional tactile observations and a force-based control space. The codebase and design files are open-sourced and available at https://tactile-farm.github.io .

Whole-body humanoid manipulation of bulky, deformable, and shared-load objects requires distributed contact sensing and explicit force regulation, yet most imitation policies treat contact force only implicitly. On the other hand, different demonstration sources provide complementary modalities with inherent trade-offs: human demonstrations capture natural contact forces but not robot-executable actions, while teleoperation directly records robot actions but with less natural force regulation. This paper presents WT-UMI, a wearable whole-body tactile interface worn by human operators or mounted on humanoids, providing accurate observations of tactile images, contact forces, and end-effector poses across both human demonstration and humanoid teleoperation modes. We introduce a force-conditioned target-pose correction module that converts measured human poses into contact-aware robot targets by learning corrections from teleoperation data. To leverage the natural force interaction in human data, we propose a force-supervised planner that predicts end-effector pose chunks and contact-force trajectories. The predicted contact force serves as the reference for a tactile-based admittance controller. Across five contact-rich tasks spanning deformable objects, bulky rigid objects, and human--humanoid collaboration, WT-UMI improves success rate and reduces contact-position tracking error over four policy baselines. Our project page is available at https://wt-umi.github.io/WTUMI/.

Contact-rich manipulation remains a major challenge in robotics. Optical tactile sensors like GelSight Mini offer a low-cost solution for contact sensing by capturing soft-body deformations of the silicone gel. However, accurately inferring shear and normal force distributions from these gel deformations has yet to be fully addressed. In this work, we propose a machine learning approach using a U-net architecture to predict force distributions directly from the sensor's raw images. Our model, trained on force distributions inferred from fea, demonstrates promising accuracy in predicting normal and shear force distributions for the commercially available GelSight Mini sensor. It also shows potential for generalization across indenters, sensors of the same type, and for enabling real-time application. The codebase, dataset and models are open-sourced and available at https://feats-ai.github.io .

Generating realistic 3D Human-Object Interactions (HOI) is a fundamental task for applications ranging from embodied AI to virtual content creation, which requires harmonizing high-level semantic intent with strict low-level physical constraints. Existing methods excel at semantic alignment, however, they struggle to maintain precise object contact. We reveal a key finding termed Geometric Forgetting: as diffusion model depth increases, semantic feature tend to overshadow object geometry feature, causing the model to lose its perception to object geometry. To address this, we propose MaMi-HOI, a hierarchical framework reconciling Macro-level kinematic fluidity with Micro-level spatial precision. First, to counteract geometric forgetting, we introduce the Geometry-Aware Proximity Adapter (GAPA), which explicitly re-injects dense object details to perform residual snapping corrections for precise contact. Nevertheless, such aggressive local enforcement can disrupt global dynamics, leading to robotic stiffness. In response, we introduce the Kinematic Harmony Adapter (KHA), which proactively aligns whole-body posture with spatial objectives, ensuring the skeleton actively accommodates constraints without compromising naturalness. Extensive experiments validate that MaMi-HOI simultaneously achieves natural motion and precise contact. Crucially, it extends generation capabilities to long-term tasks with complex trajectories, effectively bridging the gap between global navigation and high-fidelity manipulation in 3D scenes. Code is available at https://github.com/DON738110198/MaMi-HOI.git

Cells that collide with each other repolarize away from contact, in a process called contact inhibition of locomotion (CIL), which is necessary for correct development of the embryo. CIL can occur even when cells make a micron-scale contact with a neighbor - much smaller than their size. How precisely can a cell sense cell-cell contact and repolarize in the correct direction? What factors control whether a cell recognizes it has contacted a neighbor? We propose a theoretical model for the limits of CIL where cells recognize the presence of another cell by binding the protein ephrin with the Eph receptor. This recognition is made difficult by the presence of interfering ligands that bind nonspecifically. Both theoretical predictions and simulation results show that it becomes more difficult to sense cell-cell contact when it is difficult to distinguish ephrin from the interfering ligands, or when there are more interfering ligands, or when the contact width decreases. However, the error of estimating contact position remains almost constant when the contact width changes. This happens because the cell gains spatial information largely from the boundaries of cell-cell contact. We study using statistical decision theory the likelihood of a false positive CIL event in the absence of cell-cell contact, and the likelihood of a false negative where CIL does not occur when another cell is present. Our results suggest that the cell is more likely to make incorrect decisions when the contact width is very small or so large that it nears the cell's perimeter. However, in general, we find that cells have the ability to make reasonably reliable CIL decisions even for very narrow (micron-scale) contacts, even if the concentration of interfering ligands is ten times that of the correct ligands.

Development of dexterous manipulation hardware has primarily focused on hands and grippers. However, these end-effectors are often paired with bulky and highly stiff wrists that limit performance in human environments. More designs have adopted backdrivable actuation, but are still difficult to model and control due to coupled kinematics or high mechanical inertia from heavy links. We present DexWrist, a robotic wrist that advances manipulation in highly constrained environments and enables dynamic, contact-rich tasks. We achieve this by combining quasi-direct drive actuation with a decoupled parallel kinematic mechanism in a compact design. It delivers 3.75 +/- 0.05 Nm rated torque, 0.33 +/- 0.06 Nm backdrive torque, 10.15 +/- 1.34 Hz torque bandwidth, +/- 40 degrees ROM in both DOFs, and a one-to-one motor-to-DOF mapping in a 0.97 kg package. In practice, these properties increase workspace in cluttered environments and stabilize contact without the need for finely tuned admittance control. We evaluate DexWrist as a drop-in wrist upgrade in simulation and on two robot arms performing representative constrained and contact-rich tasks. In learned policy evaluations, DexWrist achieved 50-76% relative improvements in success rate, and reduced autonomous task completion times by 3-5x. More details about DexWrist can be found at https://dexwrist.csail.mit.edu.

We show that Hertzian particle contacts are the underlying cause of the as-yet-unexplained noninteger power laws in weakly nonlinear rheology. In the medium amplitude oscillatory shear (MAOS) region, the cubic scaling of the leading order nonlinear shear stress (σ_3 sim γ_0^{m_3}, m_3=3) is the standard expectation. Expanding on the work by Natalia et al. [J. Rheol. 64 625-635 (2020)], we report an extensive data set of noncubical, noninteger power law scalings m_3 for particle suspensions in two immiscible fluids with a capillary attractive interaction, known as capillary suspensions. Here, we show that distinct power law exponents are found for the storage and loss moduli and these noninteger scalings occur at every secondary fluid concentration for two different contact angles. These compelling results indicate that the noninteger scalings are related to the underlying microstructure of capillary suspensions. We show that the magnitude of the third harmonic elastic stress scaling m_3,elastic originates from Hertzian-like contacts in combination with the attractive capillary force. The related third harmonic viscous stress scaling m_3,viscous is, found to be associated with adhesive-controlled friction. These observations, conducted for a wide range of compositions, can help explain previous reports of noninteger scaling for materials involving particle contacts and offers a new opportunity using the variable power law exponent of MAOS rheology to reveal the physics of particle bonds and friction in the rheological response under low deformation instead of at very high shear rates.

This paper presents a novel vision-based proprioception approach for a soft robotic finger that can estimate and reconstruct tactile interactions in both terrestrial and aquatic environments. The key to this system lies in the finger's unique metamaterial structure, which facilitates omni-directional passive adaptation during grasping, protecting delicate objects across diverse scenarios. A compact in-finger camera captures high-framerate images of the finger's deformation during contact, extracting crucial tactile data in real-time. We present a volumetric discretized model of the soft finger and use the geometry constraints captured by the camera to find the optimal estimation of the deformed shape. The approach is benchmarked using a motion capture system with sparse markers and a haptic device with dense measurements. Both results show state-of-the-art accuracies, with a median error of 1.96 mm for overall body deformation, corresponding to 2.1% of the finger's length. More importantly, the state estimation is robust in both on-land and underwater environments as we demonstrate its usage for underwater object shape sensing. This combination of passive adaptation and real-time tactile sensing paves the way for amphibious robotic grasping applications.

Tactile sensing plays a vital role in enabling robots to perform fine-grained, contact-rich tasks. However, the high dimensionality of tactile data, due to the large coverage on dexterous hands, poses significant challenges for effective tactile feature learning, especially for 3D tactile data, as there are no large standardized datasets and no strong pretrained backbones. To address these challenges, we propose a novel canonical representation that reduces the difficulty of 3D tactile feature learning and further introduces a force-based self-supervised pretraining task to capture both local and net force features, which are crucial for dexterous manipulation. Our method achieves an average success rate of 78% across four fine-grained, contact-rich dexterous manipulation tasks in real-world experiments, demonstrating effectiveness and robustness compared to other methods. Further analysis shows that our method fully utilizes both spatial and force information from 3D tactile data to accomplish the tasks. The codes and videos can be viewed at https://3dtacdex.github.io.

Achieving a desired impedance during physical interaction remains a central problem in compliant control. In many practical implementations, admittance control combined with linear position controllers is employed, but this structure typically results in only approximate impedance behavior. This paper establishes a rigorous equivalence between the impedance realization problem and the generalized output regulation theory, and shows that, under the admittance architecture and assuming the inner position controller is restricted to linear combinations of commonly used signals, a unique control law exists that achieves exact compliant control. The resulting controller introduces additional terms with respect to a conventional PD formulation, while preserving a simple structure. Numerical simulations are used to illustrate the effectiveness of the proposed approach under nominal conditions and in the presence of model uncertainties, and to compare its performance against a standard PD controller. The results demonstrate improved interaction performance and robustness, supporting the theoretical analysis.

In parallel simulation, convergence and parallelism are often seen as inherently conflicting objectives. Improved parallelism typically entails lighter local computation and weaker coupling, which unavoidably slow the global convergence. This paper presents a novel GPU algorithm that achieves convergence rates comparable to fullspace Newton's method while maintaining good parallelizability just like the Jacobi method. Our approach is built on a key insight into the phenomenon of overshoot. Overshoot occurs when a local solver aggressively minimizes its local energy without accounting for the global context, resulting in a local update that undermines global convergence. To address this, we derive a theoretically second-order optimal solution to mitigate overshoot. Furthermore, we adapt this solution into a pre-computable form. Leveraging Cubature sampling, our runtime cost is only marginally higher than the Jacobi method, yet our algorithm converges nearly quadratically as Newton's method. We also introduce a novel full-coordinate formulation for more efficient pre-computation. Our method integrates seamlessly with the incremental potential contact method and achieves second-order convergence for both stiff and soft materials. Experimental results demonstrate that our approach delivers high-quality simulations and outperforms state-of-the-art GPU methods with 50 to 100 times better convergence.

Physical interaction quality is central to deformable-object manipulation, yet most benchmarks evaluate task success alone. A policy may complete the task while allowing slip or causing excessive compression. A primary bottleneck is the absence of visuo-tactile datasets that pair policy-visible contact observations with independent physical ground truth over complete tasks. We introduce SoftVTBench, a visuo-tactile dataset for physical-interaction-aware deformable-object manipulation. It contains 4,000 expert demonstrations and more than 50 assets, including volumetric deformable objects and visually matched rigid twins. At 20 Hz, each episode synchronizes multi-view RGB, dual-finger tactile RGB and marker motion, proprioception, language, and binary and continuous gripper actions, alongside evaluator-only finite-element (FEM) states. Building upon this dataset, we establish a closed-loop benchmark that uses fixed object-specific calibration to define the Deformation-aware Success Rate (DSR), which counts a rollout as successful only when it completes the task and keeps peak normalized deformation within tolerance. Across Diffusion Policy, π_{0.5}, and FastWAM, all 12 in-distribution configurations contain successful rollouts that violate the deformation tolerance, accounting for 0.7--24% of each configuration's successes. Under distribution shift, visuo-tactile variants achieve higher task success in all six policy--suite comparisons and higher DSR in five, whereas their in-distribution benefits are mixed. These results show that making touch available does not by itself ensure effective multimodal fusion. SoftVTBench therefore provides a common visuo-tactile resource for studying not only whether a policy succeeds, but how it physically interacts with deformable objects and when touch improves that interaction.

Proprioception is the "sixth sense" that detects limb postures with motor neurons. It requires a natural integration between the musculoskeletal systems and sensory receptors, which is challenging among modern robots that aim for lightweight, adaptive, and sensitive designs at a low cost. Here, we present the Soft Polyhedral Network with an embedded vision for physical interactions, capable of adaptive kinesthesia and viscoelastic proprioception by learning kinetic features. This design enables passive adaptations to omni-directional interactions, visually captured by a miniature high-speed motion tracking system embedded inside for proprioceptive learning. The results show that the soft network can infer real-time 6D forces and torques with accuracies of 0.25/0.24/0.35 N and 0.025/0.034/0.006 Nm in dynamic interactions. We also incorporate viscoelasticity in proprioception during static adaptation by adding a creep and relaxation modifier to refine the predicted results. The proposed soft network combines simplicity in design, omni-adaptation, and proprioceptive sensing with high accuracy, making it a versatile solution for robotics at a low cost with more than 1 million use cycles for tasks such as sensitive and competitive grasping, and touch-based geometry reconstruction. This study offers new insights into vision-based proprioception for soft robots in adaptive grasping, soft manipulation, and human-robot interaction.

Operating robots precisely and at high speeds has been a long-standing goal of robotics research. Balancing these competing demands is key to enabling the seamless collaboration of robots and humans and increasing task performance. However, traditional motor-driven systems often fall short in this balancing act. Due to their rigid and often heavy design exacerbated by positioning the motors into the joints, faster motions of such robots transfer high forces at impact. To enable precise and safe dynamic motions, we introduce a four degree-of-freedom~(DoF) tendon-driven robot arm. Tendons allow placing the actuation at the base to reduce the robot's inertia, which we show significantly reduces peak collision forces compared to conventional robots with motors placed near the joints. Pairing our robot with pneumatic muscles allows generating high forces and highly accelerated motions, while benefiting from impact resilience through passive compliance. Since tendons are subject to additional friction and hence prone to wear and tear, we validate the reliability of our robotic arm on various experiments, including long-term dynamic motions. We also demonstrate its ease of control by quantifying the nonlinearities of the system and the performance on a challenging dynamic table tennis task learned from scratch using reinforcement learning. We open-source the entire hardware design, which can be largely 3D printed, the control software, and a proprioceptive dataset of 25 days of diverse robot motions at webdav.tuebingen.mpg.de/pamy2.

Simulation is widely used in robotics for system verification and large-scale data collection. However, simulating sensors, including tactile sensors, has been a long-standing challenge. In this paper, we propose Taxim, a realistic and high-speed simulation model for a vision-based tactile sensor, GelSight. A GelSight sensor uses a piece of soft elastomer as the medium of contact and embeds optical structures to capture the deformation of the elastomer, which infers the geometry and forces applied at the contact surface. We propose an example-based method for simulating GelSight: we simulate the optical response to the deformation with a polynomial look-up table. This table maps the deformed geometries to pixel intensity sampled by the embedded camera. In order to simulate the surface markers' motion that is caused by the surface stretch of the elastomer, we apply the linear elastic deformation theory and the superposition principle. The simulation model is calibrated with less than 100 data points from a real sensor. The example-based approach enables the model to easily migrate to other GelSight sensors or its variations. To the best of our knowledge, our simulation framework is the first to incorporate marker motion field simulation that derives from elastomer deformation together with the optical simulation, creating a comprehensive and computationally efficient tactile simulation framework. Experiments reveal that our optical simulation has the lowest pixel-wise intensity errors compared to prior work and can run online with CPU computing. Our code and supplementary materials are open-sourced at https://github.com/CMURoboTouch/Taxim.

The growing adoption of batteries in the electric vehicle industry and various consumer products has created an urgent need for effective recycling solutions. These products often contain a mix of compliant and rigid components, making robotic disassembly a critical step toward achieving scalable recycling processes. Diffusion policy has emerged as a promising approach for learning low-level skills in robotics. To effectively apply diffusion policy to contact-rich tasks, incorporating force as feedback is essential. In this paper, we apply diffusion policy with vision and force in a compliant object prying task. However, when combining low-dimensional contact force with high-dimensional image, the force information may be diluted. To address this issue, we propose a method that effectively integrates force with image data for diffusion policy observations. We validate our approach on a battery prying task that demands high precision and multi-step execution. Our model achieves a 96\% success rate in diverse scenarios, marking a 57\% improvement over the vision-only baseline. Our method also demonstrates zero-shot transfer capability to handle unseen objects and battery types. Supplementary videos and implementation codes are available on our project website. https://rros-lab.github.io/diffusion-with-force.github.io/

Nonlinear elastic properties of polymers and polymeric composites are essential for accurate prediction of their response to dynamic loads, which is crucial in a wide range of applications. These properties can be affected by strain rate, temperature, and pressure. The temperature susceptibility of nonlinear elastic moduli of polymers remains poorly understood. We have recently observed a significant frequency dependence of the nonlinear elastic (Murnaghan) moduli of polystyrene. In this paper we expand this analysis by the temperature dependence. The measurement methodology was based on the acousto-elastic effect, and involved analysis of the dependencies of velocities of longitudinal and shear single-frequency ultrasonic waves in the sample on the applied static pressure. Measurements were performed at different temperatures in the range of 25-65 {\deg}C and at different frequencies in the range of 0.75-3 MHz. The temperature susceptibility of the nonlinear moduli l and m was found to be two orders of magnitude larger than that of linear moduli lambda and mu. At the same time, the observed variations of n modulus with temperature were low and within the measurement tolerance. The observed tendencies can be explained by different influence of pressure on relaxation processes in the material at different temperatures.

Most learned dexterous grasp generators relegate contact forces to a downstream verification step, so a kinematically-plausible pose can still violate the conditions for a stable physical grasp. We address this with EquiDexFlow, an SE(3)-equivariant flow-matching model that jointly predicts wrist pose, joint angles, fingertip contacts, surface normals, and contact forces from an object point cloud. Our architecture projects contacts onto the object surface and forces into the Coulomb friction cone by construction, so placement and friction compliance hold without loss penalties. We prove end-to-end SE(3) equivariance and verify it empirically over 200 rotations, with wrist residuals below 0.04^circ and exactly zero joint deviation. Trained on 8,100 force-closure grasps across 81 objects for the 16-DoF Allegro Hand, our model achieves zero friction violations, the best composite score, and the lowest wrench residual among all ablation variants. We retarget decoded fingertip contacts to a 16-DoF LEAP Hand via per-finger inverse kinematics, and our hardware-feasible refinement places every joint at least 5% inside its actuator envelope while preserving wrench balance. On the physical robot, retargeted EquiDexFlow-decoded grasps complete open-loop pick-and-hold trials on all six test objects, with every asymmetric object succeeding at both the canonical pose and a 120^circ co-rotation. Videos, code, and checkpoints are available at https://equidexflow.github.io.

Compliance plays a crucial role in manipulation, as it balances between the concurrent control of position and force under uncertainties. Yet compliance is often overlooked by today's visuomotor policies that solely focus on position control. This paper introduces Adaptive Compliance Policy (ACP), a novel framework that learns to dynamically adjust system compliance both spatially and temporally for given manipulation tasks from human demonstrations, improving upon previous approaches that rely on pre-selected compliance parameters or assume uniform constant stiffness. However, computing full compliance parameters from human demonstrations is an ill-defined problem. Instead, we estimate an approximate compliance profile with two useful properties: avoiding large contact forces and encouraging accurate tracking. Our approach enables robots to handle complex contact-rich manipulation tasks and achieves over 50\% performance improvement compared to state-of-the-art visuomotor policy methods. For result videos, see https://adaptive-compliance.github.io/

Teleoperation of robotic systems for precise and delicate object grasping requires high-fidelity haptic feedback to obtain comprehensive real-time information about the grasp. In such cases, the most common approach is to use kinesthetic feedback. However, a single contact point information is insufficient to detect the dynamically changing shape of soft objects. This paper proposes a novel telemanipulation system that provides kinesthetic and cutaneous stimuli to the user's hand to achieve accurate liquid dispensing by dexterously manipulating the deformable object (i.e., pipette). The experimental results revealed that the proposed approach to provide the user with multimodal haptic feedback considerably improves the quality of dosing with a remote pipette. Compared with pure visual feedback, the relative dosing error decreased by 66\% and task execution time decreased by 18\% when users manipulated the deformable pipette with a multimodal haptic interface in combination with visual feedback. The proposed technology can be potentially implemented in delicate dosing procedures during the antibody tests for COVID-19, chemical experiments, operation with organic materials, and telesurgery.

While large-scale human motion capture datasets have advanced human motion generation, modeling and generating dynamic 3D human-object interactions (HOIs) remain challenging due to dataset limitations. Existing datasets often lack extensive, high-quality motion and annotation and exhibit artifacts such as contact penetration, floating, and incorrect hand motions. To address these issues, we introduce InterAct, a large-scale 3D HOI benchmark featuring dataset and methodological advancements. First, we consolidate and standardize 21.81 hours of HOI data from diverse sources, enriching it with detailed textual annotations. Second, we propose a unified optimization framework to enhance data quality by reducing artifacts and correcting hand motions. Leveraging the principle of contact invariance, we maintain human-object relationships while introducing motion variations, expanding the dataset to 30.70 hours. Third, we define six benchmarking tasks and develop a unified HOI generative modeling perspective, achieving state-of-the-art performance. Extensive experiments validate the utility of our dataset as a foundational resource for advancing 3D human-object interaction generation. To support continued research in this area, the dataset is publicly available at https://github.com/wzyabcas/InterAct, and will be actively maintained.

Wheel-legged robots with integrated manipulators hold great promise for mobile manipulation in logistics, industrial automation, and human-robot collaboration. However, unified control of such systems remains challenging due to the redundancy in degrees of freedom, complex wheel-ground contact dynamics, and the need for seamless coordination between locomotion and manipulation. In this work, we present the design and whole-body motion control of an omnidirectional wheel-legged quadrupedal robot equipped with a dexterous manipulator. The proposed platform incorporates independently actuated steering modules and hub-driven wheels, enabling agile omnidirectional locomotion with high maneuverability in structured environments. To address the challenges of contact-rich interaction, we develop a contact-aware whole-body dynamic optimization framework that integrates point-contact modeling for manipulation with line-contact modeling for wheel-ground interactions. A warm-start strategy is introduced to accelerate online optimization, ensuring real-time feasibility for high-dimensional control. Furthermore, a unified kinematic model tailored for the robot's 4WIS-4WID actuation scheme eliminates the need for mode switching across different locomotion strategies, improving control consistency and robustness. Simulation and experimental results validate the effectiveness of the proposed framework, demonstrating agile terrain traversal, high-speed omnidirectional mobility, and precise manipulation under diverse scenarios, underscoring the system's potential for factory automation, urban logistics, and service robotics in semi-structured environments.

Haptic displays play an important role in enhancing the sense of presence in VR and telepresence. Displaying the tactile properties of fabrics has potential in the fashion industry, but there are difficulties in dynamically displaying different types of tactile sensations while maintaining their flexible properties. The vibrotactile stimulation of fabrics is an important element in the tactile properties of fabrics, as it greatly affects the way a garment feels when rubbed against the skin. To dynamically change the vibrotactile stimuli, many studies have used mechanical actuators. However, when combined with fabric, the soft properties of the fabric are compromised by the stiffness of the actuator. In addition, because the vibration generated by such actuators is applied to a single point, it is not possible to provide a uniform tactile sensation over the entire surface of the fabric, resulting in an uneven tactile sensation. In this study, we propose a Pinching Tactile Display: a conductive cloth that changes the tactile sensation by controlling electrostatic adsorption. By controlling the voltage and frequency applied to the conductive cloth, different tactile sensations can be dynamically generated. This makes it possible to create a tactile device in which tactile sensations are applied to the entire fabric while maintaining the thin and soft characteristics of the fabric. As a result, users could experiment with tactile sensations by picking up and rubbing the fabric in the same way they normally touch it. This mechanism has the potential for dynamic tactile transformation of soft materials.

Contact-rich dexterous manipulation with multi-finger hands remains an open challenge in robotics because task success depends on multi-point contacts that continuously evolve and are highly sensitive to object geometry, frictional transitions, and slip. Recently, tactile-informed manipulation policies have shown promise. However, most use tactile signals as additional observations rather than modeling contact state or how their action outputs interact with low-level controller dynamics. We present Contact-Grounded Policy (CGP), a visuotactile policy that grounds multi-point contacts by predicting coupled trajectories of actual robot state and tactile feedback, and using a learned contact-consistency mapping to convert these predictions into executable target robot states for a compliance controller. CGP consists of two components: (i) a conditional diffusion model that forecasts future robot state and tactile feedback in a compressed latent space, and (ii) a learned contact-consistency mapping that converts the predicted robot state-tactile pair into executable targets for a compliance controller, enabling it to realize the intended contacts. We evaluate CGP using a physical four-finger Allegro V5 hand with Digit360 fingertip tactile sensors, and a simulated five-finger Tesollo DG-5F hand with dense whole-hand tactile arrays. Across a range of dexterous tasks including in-hand manipulation, delicate grasping, and tool use, CGP outperforms visuomotor and visuotactile diffusion-policy baselines.

We introduce PhysLadder, a hierarchical Sim-Real benchmark for evaluating physical interaction capabilities in contact-rich manipulation. Its 16 household tasks span three cumulative levels: contact selection and geometric alignment (L1), force regulation within sustained contact (L2), and coordinated contact reconfiguration and force regulation (L3). Each task is instantiated in physically and visually matched simulated and real-world environments, with shared task definitions and success criteria. We evaluate GPT-6 Astra zero-shot with three trials per task in each environment. Real-world success rates decline from 80.0% at L1 to 47.6% at L2 and 0.0% at L3, with corresponding simulation rates of 66.7%, 47.6%, and 0.0%. Ten of the 16 tasks have identical success counts across environments; the remaining six differ by one success out of three trials. Across both environments, recurring difficulties in spatial reasoning, contact selection, force regulation, and coordination often prevent local physical progress from accumulating into task completion. These findings characterize Astra's observed capability boundary across increasing interaction demands and, for this model, support matched simulation as a repeatable, scalable testbed for studying the sustained, coordinated physical interactions that limit reliable manipulation.

Despite decades of research, general purpose in-hand manipulation remains one of the unsolved challenges of robotics. One of the contributing factors that limit current robotic manipulation systems is the difficulty of precisely sensing contact forces -- sensing and reasoning about contact forces are crucial to accurately control interactions with the environment. As a step towards enabling better robotic manipulation, we introduce DIGIT, an inexpensive, compact, and high-resolution tactile sensor geared towards in-hand manipulation. DIGIT improves upon past vision-based tactile sensors by miniaturizing the form factor to be mountable on multi-fingered hands, and by providing several design improvements that result in an easier, more repeatable manufacturing process, and enhanced reliability. We demonstrate the capabilities of the DIGIT sensor by training deep neural network model-based controllers to manipulate glass marbles in-hand with a multi-finger robotic hand. To provide the robotic community access to reliable and low-cost tactile sensors, we open-source the DIGIT design at https://digit.ml/.

The relationship between balance laws and the Principle of Virtual Work as well as the structure of contact interactions in continua remain foundational issues in Mechanics. In this work, we revisit these issues within the distributional framework emphasized by Paul Germain. We show that while the Principle of Virtual Work implies balance of forces and moments for nth-gradient continua, balance laws alone do not suffice to characterize equilibrium for n geq 2. We then reexamine Noll's classical theorem asserting that surface contact forces depend solely on the unit normal to the surface and identify the precise role of his additional assumptions, namely the absence of edge and wedge contact interactions and the boundedness of the surface contact density on the space of oriented surfaces. We demonstrate that these hypotheses fail for general higher-gradient continua. Consequently, the presence of curvature-dependent surface contact forces in such materials does not conflict with Noll's theorem and refutes his claim of their nonexistence.