Daily Papers

High-quality, long-horizon demonstrations are essential for embodied AI, yet acquiring such data for tightly coupled wheeled mobile manipulators remains a fundamental bottleneck. Unlike fixed-base systems, mobile manipulators require continuous coordination between SE(2) locomotion and precise manipulation, exposing limitations in existing teleoperation and wearable interfaces. We present SuperSuit, a bimodal data acquisition framework that supports both robot-in-the-loop teleoperation and active demonstration under a shared kinematic interface. Both modalities produce structurally identical joint-space trajectories, enabling direct data mixing without modifying downstream policies. For locomotion, SuperSuit maps natural human stepping to continuous planar base velocities, eliminating discrete command switches. For manipulation, it employs a strictly isomorphic wearable arm in both modes, while policy training is formulated in a shift-invariant delta-joint representation to mitigate calibration offsets and structural compliance without inverse kinematics. Real-world experiments on long-horizon mobile manipulation tasks show 2.6times higher demonstration throughput in active mode compared to a teleoperation baseline, comparable policy performance when substituting teleoperation data with active demonstrations at fixed dataset size, and monotonic performance improvement as active data volume increases. These results indicate that consistent kinematic representations across collection modalities enable scalable data acquisition for long-horizon mobile manipulation.

Predictive Physical AI systems output state rollouts, action chunks, and latent plans, yet a low root-mean-square error (RMSE) does not imply that a particular proposal is physically executable. We formulate physical admissibility as a prediction-control interface: before execution, a decoded proposal is treated as candidate dynamics and evaluated using kinematic, dynamic, and direct-to-composed horizon conditions. Passing is not a certificate of task success; rejection identifies violation of the specified physical envelope and gives a component-level reason. On Hugging Face LeRobot PushT, controlled falsification shows that one-step prediction-RMSE and standardized dynamics residuals reach area under the receiver operating characteristic curve (AUC) 0.982 and 0.972, kinematic-only conditions reach AUC 0.592, and the full gate reaches AUC 0.957 with condition-level attribution. In replay-based intervention experiments, residual-based filters and the full physical-admissibility gate prevent 87-$89% of invalid proposals while preserving mean progress near 0.998.

Continuum robots offer strong potential for manipulation tasks due to their high degrees of freedom, compliant structures, and operational safety. However, their adoption in both research and practical applications has been hindered by reproducibility issues arising from complex fabrication and assembly processes, challenging kinematic modeling, and a lack of intuitive control interfaces. To address these challenges, we present a novel open-source continuum robot design. The platform features a simplified fabrication pipeline enabled by multi-material 3D printing, allowing the arm to be fabricated as a monolithic compliant structure with minimal assembly. Control is achieved through an isomorphic teleoperation interface that establishes a direct actuator-level mapping, eliminating the need for explicit kinematic modeling and providing a singularity-free mapping. Building on this hardware design, the platform further supports imitation-learning-based autonomous control. The proposed system is evaluated through hardware characterization and a set of manipulation tasks. Experimental results demonstrate that the platform provides a reproducible, learning-ready continuum robot system, accelerating algorithmic development and systematic benchmarking for the continuum robotics community.

Training language-conditioned whole-body controllers for humanoid robots demands large-scale motion-language datasets. Existing approaches based on motion capture are costly and limited in diversity, while text-to-motion generative models produce purely kinematic outputs that are not guaranteed to be physically feasible. We present CLAW, a pipeline for scalable generation of language-annotated whole-body motion data for the Unitree G1 humanoid robot. CLAW composes motion primitives from a kinematic planner, parameterized by movement, heading, speed, pelvis height, and duration, and provides two browser-based interfaces--a real-time keyboard mode and a timeline-based sequence editor--for exploratory and batch data collection. A low-level controller tracks these references in MuJoCo simulation, yielding physically grounded trajectories. In parallel, a template-based engine generates diverse natural-language annotations at both segment and trajectory levels. To support scalable generation of motion-language paired data for humanoid robot learning, we make our system publicly available at: https://github.com/JianuoCao/CLAW

Vision-Language-Action models (VLAs) have demonstrated strong potential for embodied AI, yet their deployment on resource-limited robots remains challenging due to high memory and computational demands. While Post-Training Quantization (PTQ) provides an efficient solution, directly applying PTQ to VLAs often results in severe performance degradation during sequential control. We identify temporal error accumulation as a key factor, where quantization perturbations at the vision-language-to-action interface are progressively amplified, leading to kinematic drift in executed trajectories. To address this issue, we propose Drift-Aware Post-Training Quantization (DA-PTQ), which formulates quantization as a drift-aware optimization problem over sequential decision processes. DA-PTQ consists of two components: (1) Cross-Space Representation Compensation, which mitigates structured distortions between multimodal representations and action space to improve action consistency, and (2) Motion-Driven Mixed-Precision Allocation, which assigns bit-widths by minimizing trajectory-level motion errors. Extensive experiments show that DA-PTQ significantly reduces kinematic drift and achieves comparable performance to full-precision models under low-bit settings, enabling practical deployment of VLAs on resource-limited robotic platforms.

Despite the rise of billion-parameter foundation models trained across thousands of GPUs, similar scaling gains have not been shown for humanoid control. Current neural controllers for humanoids remain modest in size, target a limited set of behaviors, and are trained on a handful of GPUs over several days. We show that scaling up model capacity, data, and compute yields a generalist humanoid controller capable of creating natural and robust whole-body movements. Specifically, we posit motion tracking as a natural and scalable task for humanoid control, leveraging dense supervision from diverse motion-capture data to acquire human motion priors without manual reward engineering. We build a foundation model for motion tracking by scaling along three axes: network size (from 1.2M to 42M parameters), dataset volume (over 100M frames, 700 hours of high-quality motion data), and compute (9k GPU hours). Beyond demonstrating the benefits of scale, we show the practical utility of our model through two mechanisms: (1) a real-time universal kinematic planner that bridges motion tracking to downstream task execution, enabling natural and interactive control, and (2) a unified token space that supports various motion input interfaces, such as VR teleoperation devices, human videos, and vision-language-action (VLA) models, all using the same policy. Scaling motion tracking exhibits favorable properties: performance improves steadily with increased compute and data diversity, and learned representations generalize to unseen motions, establishing motion tracking at scale as a practical foundation for humanoid control.

Robotic simulators are a cornerstone of modern research in aerial robotics, serving both as a vehicle for the development of new control algorithms and as the data source for training reinforcement learning (RL) policies. Yet, existing quadcopter learning environments often face a trade-off between physical fidelity, multi-agent support, and the throughput required by modern deep RL pipelines. In this paper, we present MuJoCo-Drones-Gym, an open-source Gymnasium-compatible multi-drone environment built on top of the MuJoCo physics engine. MuJoCo-Drones-Gym supports an arbitrary number of Bitcraze Crazyflie 2.x nano-quadcopters and exposes a modular API for selecting (i)~the physics model (rigid-body MuJoCo, explicit Python dynamics, or any subset of ground effect, blade drag, and inter-drone downwash), (ii)~the action interface (per-motor RPMs, collective normalized thrust, velocity setpoints, or PID waypoint commands), and (iii)~the observation space (kinematic state vectors, RGB / depth / segmentation cameras, or neighbourhood adjacency information). A PettingZoo ParallelEnv wrapper enables drop-in multi-agent reinforcement learning, while a suite of seven task environments, hover, velocity tracking, multi-drone hover, waypoint navigation, formation flight, gate racing, and a generic multi-agent template, demonstrates the breadth of the interface. We describe the environment design, the underlying physics and quadcopter dynamics, and illustrate its use through control and learning examples that mirror those of the closely related gym-pybullet-drones project, while taking advantage of MuJoCo's improved contact handling, rendering, and parallelizability.

Synthesizing physics-grounded 3D assets is a critical bottleneck for interactive virtual worlds and embodied AI. Existing methods predominantly focus on static geometry, overlooking the functional properties essential for interaction. We propose that interactive asset generation must be rooted in functional logic and hierarchical physics. To bridge this gap, we introduce PhysForge, a decoupled two-stage framework supported by PhysDB, a large-scale dataset of 150,000 assets with four-tier physical annotations. First, a VLM acts as a "physical architect" to plan a "Hierarchical Physical Blueprint" defining material, functional, and kinematic constraints. Second, a physics-grounded diffusion model realizes this blueprint by synthesizing high-fidelity geometry alongside precise kinematic parameters via a novel KineVoxel Injection (KVI) mechanism. Experiments demonstrate that PhysForge produces functionally plausible, simulation-ready assets, providing a robust data engine for interactive 3D content and embodied agents.

Human motion capture from monocular videos has made significant progress in recent years. However, modern approaches often produce temporal artifacts, e.g. in form of jittery motion and struggle to achieve smooth and physically plausible motions. Explicitly integrating physics, in form of internal forces and exterior torques, helps alleviating these artifacts. Current state-of-the-art approaches make use of an automatic PD controller to predict torques and reaction forces in order to re-simulate the input kinematics, i.e. the joint angles of a predefined skeleton. However, due to imperfect physical models, these methods often require simplifying assumptions and extensive preprocessing of the input kinematics to achieve good performance. To this end, we propose a novel method to selectively incorporate the physics models with the kinematics observations in an online setting, inspired by a neural Kalman-filtering approach. We develop a control loop as a meta-PD controller to predict internal joint torques and external reaction forces, followed by a physics-based motion simulation. A recurrent neural network is introduced to realize a Kalman filter that attentively balances the kinematics input and simulated motion, resulting in an optimal-state dynamics prediction. We show that this filtering step is crucial to provide an online supervision that helps balancing the shortcoming of the respective input motions, thus being important for not only capturing accurate global motion trajectories but also producing physically plausible human poses. The proposed approach excels in the physics-based human pose estimation task and demonstrates the physical plausibility of the predictive dynamics, compared to state of the art. The code is available on https://github.com/cuongle1206/OSDCap

Text- and image-conditioned video generation models have achieved strong visual fidelity and temporal coherence, but they often fail to generate motion governed by kinematic and geometric constraints. In these settings, object parts must remain rigid, maintain contact or coupling with neighboring components, and transfer motion consistently across connected parts. These requirements are especially explicit in articulated mechanical assemblies, where motion is constrained by rigid-link geometry, contact/coupling relations, and transmission through kinematic chains. A generated video may therefore appear plausible while violating the intended mechanism, such as rotating a part that should translate, deforming a rigid component, breaking coupling between parts, or failing to move downstream components. To evaluate this gap, We introduce MechVerse, a benchmark for mechanically consistent image-to-video generation. MechVerse contains 21,156 synthetic clips from 1,357 mechanical assemblies across 141 categories, organized into three tiers of increasing kinematic complexity: independent articulation, pairwise coupling, and densely coupled multi-part mechanisms. Each clip is paired with a structured prompt describing part identities, stationary supports, moving components, motion primitives, direction, speed/extent, and inter-part dependencies. We evaluate proprietary, open-source, and fine-tuned image-to-video models using standard video metrics, instruction-following scores, and human judgments of motion correctness and kinematic coupling. Results show that current models can preserve appearance and smoothness while failing to generate mechanically admissible motion, with errors increasing as coupling complexity grows. MechVerse provides a benchmark for measuring and improving mechanism-aware video generation from image and language inputs.

Generating realistic 3D Human-Object Interactions (HOI) is a fundamental task for applications ranging from embodied AI to virtual content creation, which requires harmonizing high-level semantic intent with strict low-level physical constraints. Existing methods excel at semantic alignment, however, they struggle to maintain precise object contact. We reveal a key finding termed Geometric Forgetting: as diffusion model depth increases, semantic feature tend to overshadow object geometry feature, causing the model to lose its perception to object geometry. To address this, we propose MaMi-HOI, a hierarchical framework reconciling Macro-level kinematic fluidity with Micro-level spatial precision. First, to counteract geometric forgetting, we introduce the Geometry-Aware Proximity Adapter (GAPA), which explicitly re-injects dense object details to perform residual snapping corrections for precise contact. Nevertheless, such aggressive local enforcement can disrupt global dynamics, leading to robotic stiffness. In response, we introduce the Kinematic Harmony Adapter (KHA), which proactively aligns whole-body posture with spatial objectives, ensuring the skeleton actively accommodates constraints without compromising naturalness. Extensive experiments validate that MaMi-HOI simultaneously achieves natural motion and precise contact. Crucially, it extends generation capabilities to long-term tasks with complex trajectories, effectively bridging the gap between global navigation and high-fidelity manipulation in 3D scenes. Code is available at https://github.com/DON738110198/MaMi-HOI.git

Inverse kinematics (IK) is a core operation in animation, robotics, and biomechanics: given Cartesian constraints, recover joint rotations under a known kinematic tree. In many real-time human avatar pipelines, the available signal per frame is a sparse set of tracked 3D joint positions, whereas animation systems require joint orientations to drive skinning. Recovering full orientations from positions is underconstrained, most notably because twist about bone axes is ambiguous, and classical IK solvers typically rely on iterative optimization that can be slow and sensitive to noisy inputs. We introduce IK-GAT, a lightweight graph-attention network that reconstructs full-body joint orientations from 3D joint positions in a single forward pass. The model performs message passing over the skeletal parent-child graph to exploit kinematic structure during rotation inference. To simplify learning, IK-GAT predicts rotations in a bone-aligned world-frame representation anchored to rest-pose bone frames. This parameterization makes the twist axis explicit and is exactly invertible to standard parent-relative local rotations given the kinematic tree and rest pose. The network uses a continuous 6D rotation representation and is trained with a geodesic loss on SO(3) together with an optional forward-kinematics consistency regularizer. IK-GAT produces animation-ready local rotations that can directly drive a rigged avatar or be converted to pose parameters of SMPL-like body models for real-time and online applications. With 374K parameters and over 650 FPS on CPU, IK-GAT outperforms VPoser-based per-frame iterative optimization without warm-start at significantly lower cost, and is robust to initial pose and input noise

Hand-Object Interaction (HOI) generation plays a critical role in advancing applications across animation and robotics. Current video-based methods are predominantly single-view, which impedes comprehensive 3D geometry perception and often results in geometric distortions or unrealistic motion patterns. While 3D HOI approaches can generate dynamically plausible motions, their dependence on high-quality 3D data captured in controlled laboratory settings severely limits their generalization to real-world scenarios. To overcome these limitations, we introduce SyncMV4D, the first model that jointly generates synchronized multi-view HOI videos and 4D motions by unifying visual prior, motion dynamics, and multi-view geometry. Our framework features two core innovations: (1) a Multi-view Joint Diffusion (MJD) model that co-generates HOI videos and intermediate motions, and (2) a Diffusion Points Aligner (DPA) that refines the coarse intermediate motion into globally aligned 4D metric point tracks. To tightly couple 2D appearance with 4D dynamics, we establish a closed-loop, mutually enhancing cycle. During the diffusion denoising process, the generated video conditions the refinement of the 4D motion, while the aligned 4D point tracks are reprojected to guide next-step joint generation. Experimentally, our method demonstrates superior performance to state-of-the-art alternatives in visual realism, motion plausibility, and multi-view consistency.

Long-horizon failure in world models is conventionally attributed to compounding error, a generic framing that does not distinguish what kind of error compounds. We propose a kinematic-vs-dynamic reframing: world models tend to imagine kinematically rather than dynamically. We operationalize this as the imagined Kinematic-Consistency Error, a per-step diagnostic that measures how far a rollout departs from a closed-form kinematic null, paired with a perturbation protocol that tests whether iKCE responds when physical conditions cross a regime boundary. We instantiate the diagnostic on a released DreamerV3 checkpoint trained on DMC walker-walk, where imagined iKCE runs roughly two orders of magnitude above that of matched real-physics rollouts. Across a friction sweep that crosses the gait-collapse boundary, the model's iKCE stays statistically flat even as the trained policy's reward collapses through the same range, providing the kinematic-not-dynamic signature. The diagnostic distinguishes kinematic from dynamic imagination at horizons longer than the embodiment's gait period.

Teleoperation systems are essential for efficiently collecting diverse and high-quality robot demonstration data, especially for complex, contact-rich tasks. However, current teleoperation platforms typically lack integrated force feedback, cross-embodiment generalization, and portable, user-friendly designs, limiting their practical deployment. To address these limitations, we introduce ACE-F, a cross embodiment foldable teleoperation system with integrated force feedback. Our approach leverages inverse kinematics (IK) combined with a carefully designed human-robot interface (HRI), enabling users to capture precise and high-quality demonstrations effortlessly. We further propose a generalized soft-controller pipeline integrating PD control and inverse dynamics to ensure robot safety and precise motion control across diverse robotic embodiments. Critically, to achieve cross-embodiment generalization of force feedback without additional sensors, we innovatively interpret end-effector positional deviations as virtual force signals, which enhance data collection and enable applications in imitation learning. Extensive teleoperation experiments confirm that ACE-F significantly simplifies the control of various robot embodiments, making dexterous manipulation tasks as intuitive as operating a computer mouse. The system is open-sourced at: https://acefoldable.github.io/

Broader access to high-quality movement analysis could greatly benefit movement science and rehabilitation, such as allowing more detailed characterization of movement impairments and responses to interventions, or even enabling early detection of new neurological conditions or fall risk. While emerging technologies are making it easier to capture kinematics with biomechanical models, or how joint angles change over time, inferring the underlying physics that give rise to these movements, including ground reaction forces, joint torques, or even muscle activations, is still challenging. Here we explore whether imitation learning applied to a biomechanical model from a large dataset of movements from able-bodied and impaired individuals can learn to compute these inverse dynamics. Although imitation learning in human pose estimation has seen great interest in recent years, our work differences in several ways: we focus on using an accurate biomechanical model instead of models adopted for computer vision, we test it on a dataset that contains participants with impaired movements, we reported detailed tracking metrics relevant for the clinical measurement of movement including joint angles and ground contact events, and finally we apply imitation learning to a muscle-driven neuromusculoskeletal model. We show that our imitation learning policy, KinTwin, can accurately replicate the kinematics of a wide range of movements, including those with assistive devices or therapist assistance, and that it can infer clinically meaningful differences in joint torques and muscle activations. Our work demonstrates the potential for using imitation learning to enable high-quality movement analysis in clinical practice.

Recent models for video generation have achieved remarkable progress and are now deployed in film, social media production, and advertising. Beyond their creative potential, such models also hold promise as world simulators for robotics and embodied decision making. Despite strong advances, however, current approaches still struggle to generate physically plausible object interactions and lack physics-grounded control mechanisms. To address this limitation, we introduce KineMask, an approach for physics-guided video generation that enables realistic rigid body control, interactions, and effects. Given a single image and a specified object velocity, our method generates videos with inferred motions and future object interactions. We propose a two-stage training strategy that gradually removes future motion supervision via object masks. Using this strategy we train video diffusion models (VDMs) on synthetic scenes of simple interactions and demonstrate significant improvements of object interactions in real scenes. Furthermore, KineMask integrates low-level motion control with high-level textual conditioning via predictive scene descriptions, leading to effective support for synthesis of complex dynamical phenomena. Extensive experiments show that KineMask achieves strong improvements over recent models of comparable size. Ablation studies further highlight the complementary roles of low- and high-level conditioning in VDMs. Our code, model, and data will be made publicly available.

Human motion generation holds significant promise in fields such as animation, film production, and robotics. However, existing methods often fail to produce physically plausible movements that adhere to biomechanical principles. While recent autoregressive and diffusion models have improved visual quality, they frequently overlook essential biodynamic features, such as muscle activation patterns and joint coordination, leading to motions that either violate physical laws or lack controllability. This paper introduces BioMoDiffuse, a novel biomechanics-aware diffusion framework that addresses these limitations. It features three key innovations: (1) A lightweight biodynamic network that integrates muscle electromyography (EMG) signals and kinematic features with acceleration constraints, (2) A physics-guided diffusion process that incorporates real-time biomechanical verification via modified Euler-Lagrange equations, and (3) A decoupled control mechanism that allows independent regulation of motion speed and semantic context. We also propose a set of comprehensive evaluation protocols that combines traditional metrics (FID, R-precision, etc.) with new biomechanical criteria (smoothness, foot sliding, floating, etc.). Our approach bridges the gap between data-driven motion synthesis and biomechanical authenticity, establishing new benchmarks for physically accurate motion generation.

This paper presents a novel haptic device DeltaFinger designed to deliver the force of interaction with virtual objects by guiding user's finger with wearable delta mechanism. The developed interface is capable to deliver 3D force vector to the fingertip of the index finger of the user, allowing complex rendering of virtual reality (VR) environment. The developed device is able to produce the kinesthetic feedback up to 1.8 N in vertical projection and 0.9 N in horizontal projection without restricting the motion freedom of of the remaining fingers. The experimental results showed a sufficient precision in perception of force vector with DeltaFinger (mean force vector error of 0.6 rad). The proposed device potentially can be applied to VR communications, medicine, and navigation of the people with vision problems.

Human-Scene Interaction (HSI) is a vital component of fields like embodied AI and virtual reality. Despite advancements in motion quality and physical plausibility, two pivotal factors, versatile interaction control and the development of a user-friendly interface, require further exploration before the practical application of HSI. This paper presents a unified HSI framework, UniHSI, which supports unified control of diverse interactions through language commands. This framework is built upon the definition of interaction as Chain of Contacts (CoC): steps of human joint-object part pairs, which is inspired by the strong correlation between interaction types and human-object contact regions. Based on the definition, UniHSI constitutes a Large Language Model (LLM) Planner to translate language prompts into task plans in the form of CoC, and a Unified Controller that turns CoC into uniform task execution. To facilitate training and evaluation, we collect a new dataset named ScenePlan that encompasses thousands of task plans generated by LLMs based on diverse scenarios. Comprehensive experiments demonstrate the effectiveness of our framework in versatile task execution and generalizability to real scanned scenes. The project page is at https://github.com/OpenRobotLab/UniHSI .

In sports analytics, accurately capturing both the 3D locations and rotations of body joints is essential for understanding an athlete's biomechanics. While Human Mesh Recovery (HMR) models can estimate joint rotations, they often exhibit lower accuracy in joint localization compared to 3D Human Pose Estimation (HPE) models. Recent work addressed this limitation by combining a 3D HPE model with inverse kinematics (IK) to estimate both joint locations and rotations. However, IK is computationally expensive. To overcome this, we propose a novel 2D-to-3D uplifting model that directly estimates 3D human poses, including joint rotations, in a single forward pass. We investigate multiple rotation representations, loss functions, and training strategies - both with and without access to ground truth rotations. Our models achieve state-of-the-art accuracy in rotation estimation, are 150 times faster than the IK-based approach, and surpass HMR models in joint localization precision.

For a humanoid robot to be deployed in the real world, the choice of command space (i.e., the interface between task planning and whole-body control) is crucial. Existing whole-body controllers typically demand dense kinematic or spatial references that planners struggle to synthesize from task semantics. We instead propose a compact, explicit interface that is intuitive, general, modular, and expressive enough for diverse manipulation skills. To this end, we introduce HANDOFF, a single humanoid whole-body controller that follows this interface and is distilled via multi-teacher KL distillation under a context-conditioned gating scheme into a mixture-of-experts student from three complementary specialists: whole-body motion tracking with safety-filtered data, locomotion, and fall-recovery. On the Unitree G1, HANDOFF matches state-of-the-art velocity tracking and offers one of the largest robust manipulation workspaces. We further demonstrate hardware feasibility through multiple natural-language-driven task roll-outs, powered by a VLM-driven agentic planner with no task-specific data or controller fine-tuning.

Learning motor control for muscle-driven musculoskeletal models is hindered by the computational cost of biomechanically accurate simulation and the scarcity of validated, open full-body models. Here we present MuscleMimic, an open-source framework for scalable motion imitation learning with physiologically realistic, muscle-actuated humanoids. MuscleMimic provides two validated musculoskeletal embodiments - a fixed-root upper-body model (126 muscles) for bimanual manipulation and a full-body model (416 muscles) for locomotion - together with a retargeting pipeline that maps SMPL-format motion capture data onto musculoskeletal structures while preserving kinematic and dynamic consistency. Leveraging massively parallel GPU simulation, the framework achieves order-of-magnitude training speedups over prior CPU-based approaches while maintaining comprehensive collision handling, enabling a single generalist policy to be trained on hundreds of diverse motions within days. The resulting policy faithfully reproduces a broad repertoire of human movements under full muscular control and can be fine-tuned to novel motions within hours. Biomechanical validation against experimental walking and running data demonstrates strong agreement in joint kinematics (mean correlation r = 0.90), while muscle activation analysis reveals both the promise and fundamental challenges of achieving physiological fidelity through kinematic imitation alone. By lowering the computational and data barriers to musculoskeletal simulation, MuscleMimic enables systematic model validation across diverse dynamic movements and broader participation in neuromuscular control research. Code, models, checkpoints, and retargeted datasets are available at: https://github.com/amathislab/musclemimic

We present Universal Manipulation Interface (UMI) -- a data collection and policy learning framework that allows direct skill transfer from in-the-wild human demonstrations to deployable robot policies. UMI employs hand-held grippers coupled with careful interface design to enable portable, low-cost, and information-rich data collection for challenging bimanual and dynamic manipulation demonstrations. To facilitate deployable policy learning, UMI incorporates a carefully designed policy interface with inference-time latency matching and a relative-trajectory action representation. The resulting learned policies are hardware-agnostic and deployable across multiple robot platforms. Equipped with these features, UMI framework unlocks new robot manipulation capabilities, allowing zero-shot generalizable dynamic, bimanual, precise, and long-horizon behaviors, by only changing the training data for each task. We demonstrate UMI's versatility and efficacy with comprehensive real-world experiments, where policies learned via UMI zero-shot generalize to novel environments and objects when trained on diverse human demonstrations. UMI's hardware and software system is open-sourced at https://umi-gripper.github.io.

Generalizable articulated object manipulation is essential for home-assistant robots. Recent efforts focus on imitation learning from demonstrations or reinforcement learning in simulation, however, due to the prohibitive costs of real-world data collection and precise object simulation, it still remains challenging for these works to achieve broad adaptability across diverse articulated objects. Recently, many works have tried to utilize the strong in-context learning ability of Large Language Models (LLMs) to achieve generalizable robotic manipulation, but most of these researches focus on high-level task planning, sidelining low-level robotic control. In this work, building on the idea that the kinematic structure of the object determines how we can manipulate it, we propose a kinematic-aware prompting framework that prompts LLMs with kinematic knowledge of objects to generate low-level motion trajectory waypoints, supporting various object manipulation. To effectively prompt LLMs with the kinematic structure of different objects, we design a unified kinematic knowledge parser, which represents various articulated objects as a unified textual description containing kinematic joints and contact location. Building upon this unified description, a kinematic-aware planner model is proposed to generate precise 3D manipulation waypoints via a designed kinematic-aware chain-of-thoughts prompting method. Our evaluation spanned 48 instances across 16 distinct categories, revealing that our framework not only outperforms traditional methods on 8 seen categories but also shows a powerful zero-shot capability for 8 unseen articulated object categories. Moreover, the real-world experiments on 7 different object categories prove our framework's adaptability in practical scenarios. Code is released at https://github.com/GeWu-Lab/LLM_articulated_object_manipulation/tree/main.

While large-scale human motion capture datasets have advanced human motion generation, modeling and generating dynamic 3D human-object interactions (HOIs) remain challenging due to dataset limitations. Existing datasets often lack extensive, high-quality motion and annotation and exhibit artifacts such as contact penetration, floating, and incorrect hand motions. To address these issues, we introduce InterAct, a large-scale 3D HOI benchmark featuring dataset and methodological advancements. First, we consolidate and standardize 21.81 hours of HOI data from diverse sources, enriching it with detailed textual annotations. Second, we propose a unified optimization framework to enhance data quality by reducing artifacts and correcting hand motions. Leveraging the principle of contact invariance, we maintain human-object relationships while introducing motion variations, expanding the dataset to 30.70 hours. Third, we define six benchmarking tasks and develop a unified HOI generative modeling perspective, achieving state-of-the-art performance. Extensive experiments validate the utility of our dataset as a foundational resource for advancing 3D human-object interaction generation. To support continued research in this area, the dataset is publicly available at https://github.com/wzyabcas/InterAct, and will be actively maintained.

2D keypoints are commonly used as an additional cue to refine estimated 3D human meshes. Current methods optimize the pose and shape parameters with a reprojection loss on the provided 2D keypoints. Such an approach, while simple and intuitive, has limited effectiveness because the optimal solution is hard to find in ambiguous parameter space and may sacrifice depth. Additionally, divergent gradients from distal joints complicate and deviate the refinement of proximal joints in the kinematic chain. To address these, we introduce Kinematic-Tree Rotation (KITRO), a novel mesh refinement strategy that explicitly models depth and human kinematic-tree structure. KITRO treats refinement from a bone-wise perspective. Unlike previous methods which perform gradient-based optimizations, our method calculates bone directions in closed form. By accounting for the 2D pose, bone length, and parent joint's depth, the calculation results in two possible directions for each child joint. We then use a decision tree to trace binary choices for all bones along the human skeleton's kinematic-tree to select the most probable hypothesis. Our experiments across various datasets and baseline models demonstrate that KITRO significantly improves 3D joint estimation accuracy and achieves an ideal 2D fit simultaneously. Our code available at: https://github.com/MartaYang/KITRO.

Existing hand-object interactions (HOI) methods are largely limited to rigid objects, while 4D reconstruction methods of articulated objects generally require pre-scanning the object or even multi-view videos. It remains an unexplored but significant challenge to reconstruct 4D human-articulated-object interactions from a single monocular RGB video. Fortunately, recent advancements in foundation models present a new opportunity to address this highly ill-posed problem. To this end, we introduce ArtHOI, an optimization-based framework that integrates and refines priors from multiple foundation models. Our key contribution is a suite of novel methodologies designed to resolve the inherent inaccuracies and physical unreality of these priors. In particular, we introduce an Adaptive Sampling Refinement (ASR) method to optimize object's metric scale and pose for grounding its normalized mesh in world space. Furthermore, we propose a Multimodal Large Language Model (MLLM) guided hand-object alignment method, utilizing contact reasoning information as constraints of hand-object mesh composition optimization. To facilitate a comprehensive evaluation, we also contribute two new datasets, ArtHOI-RGBD and ArtHOI-Wild. Extensive experiments validate the robustness and effectiveness of our ArtHOI across diverse objects and interactions. Project: https://arthoi-reconstruction.github.io.

Collecting demonstrations enriched with fine-grained tactile information is critical for dexterous manipulation, particularly in contact-rich tasks that require precise force control and physical interaction. While prior works primarily focus on teleoperation or video-based retargeting, they often suffer from kinematic mismatches and the absence of real-time tactile feedback, hindering the acquisition of high-fidelity tactile data. To mitigate this issue, we propose KineDex, a hand-over-hand kinesthetic teaching paradigm in which the operator's motion is directly transferred to the dexterous hand, enabling the collection of physically grounded demonstrations enriched with accurate tactile feedback. To resolve occlusions from human hand, we apply inpainting technique to preprocess the visual observations. Based on these demonstrations, we then train a visuomotor policy using tactile-augmented inputs and implement force control during deployment for precise contact-rich manipulation. We evaluate KineDex on a suite of challenging contact-rich manipulation tasks, including particularly difficult scenarios such as squeezing toothpaste onto a toothbrush, which require precise multi-finger coordination and stable force regulation. Across these tasks, KineDex achieves an average success rate of 74.4%, representing a 57.7% improvement over the variant without force control. Comparative experiments with teleoperation and user studies further validate the advantages of KineDex in data collection efficiency and operability. Specifically, KineDex collects data over twice as fast as teleoperation across two tasks of varying difficulty, while maintaining a near-100% success rate, compared to under 50% for teleoperation.

Controlling human motion based on text presents an important challenge in computer vision. Traditional approaches often rely on holistic action descriptions for motion synthesis, which struggle to capture subtle movements of local body parts. This limitation restricts the ability to isolate and manipulate specific movements. To address this, we propose a novel motion representation that decomposes motion into distinct body joint group movements and interactions from a kinematic perspective. We design an automatic dataset collection pipeline that enhances the existing text-motion benchmark by incorporating fine-grained local joint-group motion and interaction descriptions. To bridge the gap between text and motion domains, we introduce a hierarchical motion semantics approach that progressively fuses joint-level interaction information into the global action-level semantics for modality alignment. With this hierarchy, we introduce a coarse-to-fine motion synthesis procedure for various generation and editing downstream applications. Our quantitative and qualitative experiments demonstrate that the proposed formulation enhances text-motion retrieval by improving joint-spatial understanding, and enables more precise joint-motion generation and control. Project Page: {\smallhttps://andypinxinliu.github.io/KinMo/}

We present DexUMI - a data collection and policy learning framework that uses the human hand as the natural interface to transfer dexterous manipulation skills to various robot hands. DexUMI includes hardware and software adaptations to minimize the embodiment gap between the human hand and various robot hands. The hardware adaptation bridges the kinematics gap using a wearable hand exoskeleton. It allows direct haptic feedback in manipulation data collection and adapts human motion to feasible robot hand motion. The software adaptation bridges the visual gap by replacing the human hand in video data with high-fidelity robot hand inpainting. We demonstrate DexUMI's capabilities through comprehensive real-world experiments on two different dexterous robot hand hardware platforms, achieving an average task success rate of 86%.

Mobile imitation learning on portable demonstration interfaces faces two coupled bottlenecks: locomotion-contaminated action labels and inference-induced execution latency on a continuously moving base. Recent wrist-mounted interfaces lower the cost of tabletop data collection, yet a single wrist view does not capture the global context required for base navigation. Adding a body-mounted camera entangles human walking with hand motion. Meanwhile, generative policies introduce hundreds of milliseconds of inference latency, during which the base advances past predicted waypoints, forcing backward corrections at action splices. This paper presents Mobile UMI, a hardware-free demonstration framework that addresses both gaps through three components. First, a dual-camera capture system records chest-centric global context and wrist-centric local interaction without any robot present. Second, a one-shot ChArUco-based spatial anchor unifies the chest and hand visual-inertial frames; the hand pose is then re-expressed relative to the chest to extract decoupled SE(3) manipulation and SE(2) base trajectories. Third, an asynchronous receding-horizon executor performs online state matching: each generated action chunk is realigned with the current physical pose so that expired waypoints are discarded before execution. The full system is evaluated on four long-horizon household tasks, achieving an average success rate of 83.8% over 100 trials per task. Controlled comparisons against ACT and Diffusion Policy show that the chest-relative label alone closes much of the gap; online state matching closes the remainder. These results indicate that, for mobile imitation learning under the tested conditions, explicit kinematic factorization combined with state-level latency alignment provides an effective solution without requiring architectural changes to the underlying policy class.

Human-Object Interaction (HOI) is vital for advancing simulation, animation, and robotics, enabling the generation of long-term, physically plausible motions in 3D environments. However, existing methods often fall short of achieving physics realism and supporting diverse types of interactions. To address these challenges, this paper introduces a unified Human-Object Interaction framework that provides unified control over interactions with static scenes and dynamic objects using language commands. The interactions between human and object parts can always be described as the continuous stable Relative Movement Dynamics (RMD) between human and object parts. By leveraging the world knowledge and scene perception capabilities of Vision-Language Models (VLMs), we translate language commands into RMD diagrams, which are used to guide goal-conditioned reinforcement learning for sequential interaction with objects. Our framework supports long-horizon interactions among dynamic, articulated, and static objects. To support the training and evaluation of our framework, we present a new dataset named Interplay, which includes multi-round task plans generated by VLMs, covering both static and dynamic HOI tasks. Extensive experiments demonstrate that our proposed framework can effectively handle a wide range of HOI tasks, showcasing its ability to maintain long-term, multi-round transitions. For more details, please refer to our project webpage: https://rmd-hoi.github.io/.

Physically grounded 3D assets are increasingly important for embodied AI and robotic simulation. However, most existing 3D assets lack unified physical semantics, including articulation semantics and intrinsic physical properties, required for realistic interaction. Current approaches either treat these semantics independently or rely on canonicalized object structures, limiting robustness across heterogeneous 3D assets. We present UniPhys, a scalable framework for automatically transforming raw 3D assets into simulation-ready assets with unified physical semantics. Based on UniPhys, we construct UniPhys-40K, a large-scale physically grounded dataset, together with UniPhys-Bench, a carefully verified benchmark for unified physical grounding evaluation. We further introduce UniPhysGen, a unified physical grounding model that jointly reasons over articulation semantics and intrinsic physical properties. UniPhysGen incorporates geometry-robust articulation grounding to mitigate geometric shortcut bias under heterogeneous part decompositions. Extensive experiments demonstrate state-of-the-art performance across articulation grounding and intrinsic physical property estimation tasks, while the resulting assets can be directly deployed in robotic simulation environments for realistic physical interaction. Our code and dataset will be available at https://github.com/breezexian/UniPhysGen.

Collecting real-world manipulation trajectory data involving robotic arms is essential for developing general-purpose action policies in robotic manipulation, yet such data remains scarce. Existing methods face limitations such as high costs, labor intensity, hardware dependencies, and complex setup requirements involving SLAM algorithms. In this work, we introduce Fast-UMI, an interface-mediated manipulation system comprising two key components: a handheld device operated by humans for data collection and a robot-mounted device used during policy inference. Our approach employs a decoupled design compatible with a wide range of grippers while maintaining consistent observation perspectives, allowing models trained on handheld-collected data to be directly applied to real robots. By directly obtaining the end-effector pose using existing commercial hardware products, we eliminate the need for complex SLAM deployment and calibration, streamlining data processing. Fast-UMI provides supporting software tools for efficient robot learning data collection and conversion, facilitating rapid, plug-and-play functionality. This system offers an efficient and user-friendly tool for robotic learning data acquisition.

Reconstructing articulated 3D objects is important for animation, gaming, and robotic simulations. Recent neural networks can estimate the articulated structure of 3D objects, but their generalization remains limited by the scarcity of annotated data for this task. To address this gap, we introduce Instruct-Particulate, a model that takes a 3D mesh together with a target kinematic specification, including part descriptions, connectivity, joint types, and optional point prompts, and predicts the corresponding kinematic part segmentation and joint motion parameters. The kinematic specification disambiguates the task and allows the model to target annotations of different granularity, thereby making it possible to use more abundant heterogeneous training data. At test time, the kinematic specification can be obtained automatically from large-scale vision-language models, so the model can be applied to any input mesh. To train our model at scale, we construct a heterogeneous dataset of more than 150,000 articulated 3D objects, extending existing publicly available collections with data obtained by partially labelling other 3D models (monolithic or already decomposed into parts) with kinematic labels by means of vision-language models. Experiments show that our model generalizes better across categories and to AI-generated meshes, enabling articulated asset reconstruction from real-world images via image-to-3D models.

Reconstructing biomechanically realistic 3D human motion - recovering both kinematics (motion) and kinetics (forces) - is a critical challenge. While marker-based systems are lab-bound and slow, popular monocular methods use oversimplified, anatomically inaccurate models (e.g., SMPL) and ignore physics, fundamentally limiting their biomechanical fidelity. In this work, we introduce MonoMSK, a hybrid framework that bridges data-driven learning and physics-based simulation for biomechanically realistic 3D human motion estimation from monocular video. MonoMSK jointly recovers both kinematics (motions) and kinetics (forces and torques) through an anatomically accurate musculoskeletal model. By integrating transformer-based inverse dynamics with differentiable forward kinematics and dynamics layers governed by ODE-based simulation, MonoMSK establishes a physics-regulated inverse-forward loop that enforces biomechanical causality and physical plausibility. A novel forward-inverse consistency loss further aligns motion reconstruction with the underlying kinetic reasoning. Experiments on BML-MoVi, BEDLAM, and OpenCap show that MonoMSK significantly outperforms state-of-the-art methods in kinematic accuracy, while for the first time enabling precise monocular kinetics estimation.

Imitation learning provides a promising approach to dexterous hand manipulation, but its effectiveness is limited by the lack of large-scale, high-fidelity data. Existing data-collection pipelines suffer from inaccurate motion retargeting, low data-collection efficiency, and missing high-resolution fingertip tactile sensing. We address this gap with MILE, a mechanically isomorphic teleoperation and data-collection system co-designed from human hand to exoskeleton to robotic hand. The exoskeleton is anthropometrically derived from the human hand, and the robotic hand preserves one-to-one joint-position isomorphism, eliminating nonlinear retargeting and enabling precise, natural control. The exoskeleton achieves a multi-joint mean absolute angular error below one degree, while the robotic hand integrates compact fingertip visuotactile modules that provide high-resolution tactile observations. Built on this retargeting-free interface, we teleoperate complex, contact-rich in-hand manipulation and efficiently collect a multimodal dataset comprising high-resolution fingertip visuotactile signals, RGB-D images, and joint positions. The teleoperation pipeline achieves a mean success rate improvement of 64%. Incorporating fingertip tactile observations further increases the success rate by an average of 25% over the vision-only baseline, validating the fidelity and utility of the dataset. Further details are available at: https://sites.google.com/view/mile-system.

A deep understanding of kinematic structures and movable components is essential for enabling robots to manipulate objects and model their own articulated forms. Such understanding is captured through articulated objects, which are essential for tasks such as physical simulation, motion planning, and policy learning. However, creating these models, particularly for objects with high degrees of freedom (DoF), remains a significant challenge. Existing methods typically rely on motion sequences or strong assumptions from hand-curated datasets, which hinders scalability. In this paper, we introduce Kinematify, an automated framework that synthesizes articulated objects directly from arbitrary RGB images or textual descriptions. Our method addresses two core challenges: (i) inferring kinematic topologies for high-DoF objects and (ii) estimating joint parameters from static geometry. To achieve this, we combine MCTS search for structural inference with geometry-driven optimization for joint reasoning, producing physically consistent and functionally valid descriptions. We evaluate Kinematify on diverse inputs from both synthetic and real-world environments, demonstrating improvements in registration and kinematic topology accuracy over prior work.

Pose estimation has promised to impact healthcare by enabling more practical methods to quantify nuances of human movement and biomechanics. However, despite the inherent connection between pose estimation and biomechanics, these disciplines have largely remained disparate. For example, most current pose estimation benchmarks use metrics such as Mean Per Joint Position Error, Percentage of Correct Keypoints, or mean Average Precision to assess performance, without quantifying kinematic and physiological correctness - key aspects for biomechanics. To alleviate this challenge, we develop OpenCapBench to offer an easy-to-use unified benchmark to assess common tasks in human pose estimation, evaluated under physiological constraints. OpenCapBench computes consistent kinematic metrics through joints angles provided by an open-source musculoskeletal modeling software (OpenSim). Through OpenCapBench, we demonstrate that current pose estimation models use keypoints that are too sparse for accurate biomechanics analysis. To mitigate this challenge, we introduce SynthPose, a new approach that enables finetuning of pre-trained 2D human pose models to predict an arbitrarily denser set of keypoints for accurate kinematic analysis through the use of synthetic data. Incorporating such finetuning on synthetic data of prior models leads to twofold reduced joint angle errors. Moreover, OpenCapBench allows users to benchmark their own developed models on our clinically relevant cohort. Overall, OpenCapBench bridges the computer vision and biomechanics communities, aiming to drive simultaneous advances in both areas.

Recovering ego-camera orientation from manipulation video is a prerequisite for disentangling hand motion from camera motion, a key step in imitation learning from egocentric demonstrations. The obvious approach, inferring orientation from scene geometry, fails when hands occlude the frame: VGGT, a 1B-parameter scene reconstruction model, scores worse than a constant predictor on the TACO benchmark. We identify an alternative visual concept that is present precisely when scene geometry is absent: kinematic coupling dynamics, the structured physical relationship between wrist motion and camera orientation imposed by the arm-shoulder-head chain. We find that this concept is compact (4D inter-wrist features outperform 126D full hand keypoints), temporal (requiring a GRU over short windows rather than per-frame retrieval), and physically grounded (transferring zero-shot across datasets because it is rooted in anatomy rather than scene appearance). Trained only on tabletop manipulation, WristCompass transfers zero-shot to Epic Kitchens cooking video, achieving 14.3^circ median geodesic error and approaching the performance of a 1B-parameter scene model at 200K GRU parameters.

This paper introduces ByteWrist, a novel highly-flexible and anthropomorphic parallel wrist for robotic manipulation. ByteWrist addresses the critical limitations of existing serial and parallel wrists in narrow-space operations through a compact three-stage parallel drive mechanism integrated with arc-shaped end linkages. The design achieves precise RPY (Roll-Pitch-Yaw) motion while maintaining exceptional compactness, making it particularly suitable for complex unstructured environments such as home services, medical assistance, and precision assembly. The key innovations include: (1) a nested three-stage motor-driven linkages that minimize volume while enabling independent multi-DOF control, (2) arc-shaped end linkages that optimize force transmission and expand motion range, and (3) a central supporting ball functioning as a spherical joint that enhances structural stiffness without compromising flexibility. Meanwhile, we present comprehensive kinematic modeling including forward / inverse kinematics and a numerical Jacobian solution for precise control. Empirically, we observe ByteWrist demonstrates strong performance in narrow-space maneuverability and dual-arm cooperative manipulation tasks, outperforming Kinova-based systems. Results indicate significant improvements in compactness, efficiency, and stiffness compared to traditional designs, establishing ByteWrist as a promising solution for next-generation robotic manipulation in constrained environments.

Generalist humanoid motion trackers have recently achieved strong simulation metrics by scaling data and training, yet often remain brittle on hardware during sustained teleoperation due to interface- and dynamics-induced errors. We present MOSAIC, an open-source, full-stack system for humanoid motion tracking and whole-body teleoperation across multiple interfaces. MOSAIC first learns a teleoperation-oriented general motion tracker via RL on a multi-source motion bank with adaptive resampling and rewards that emphasize world-frame motion consistency, which is critical for mobile teleoperation. To bridge the sim-to-real interface gap without sacrificing generality, MOSAIC then performs rapid residual adaptation: an interface-specific policy is trained using minimal interface-specific data, and then distilled into the general tracker through an additive residual module, outperforming naive fine-tuning or continual learning. We validate MOSAIC with systematic ablations, out-of-distribution benchmarking, and real-robot experiments demonstrating robust offline motion replay and online long-horizon teleoperation under realistic latency and noise.

This paper addresses a novel task of anticipating 3D human-object interactions (HOIs). Most existing research on HOI synthesis lacks comprehensive whole-body interactions with dynamic objects, e.g., often limited to manipulating small or static objects. Our task is significantly more challenging, as it requires modeling dynamic objects with various shapes, capturing whole-body motion, and ensuring physically valid interactions. To this end, we propose InterDiff, a framework comprising two key steps: (i) interaction diffusion, where we leverage a diffusion model to encode the distribution of future human-object interactions; (ii) interaction correction, where we introduce a physics-informed predictor to correct denoised HOIs in a diffusion step. Our key insight is to inject prior knowledge that the interactions under reference with respect to contact points follow a simple pattern and are easily predictable. Experiments on multiple human-object interaction datasets demonstrate the effectiveness of our method for this task, capable of producing realistic, vivid, and remarkably long-term 3D HOI predictions.

Synthesizing physically plausible articulated human-object interactions (HOI) without 3D/4D supervision remains a fundamental challenge. While recent zero-shot approaches leverage video diffusion models to synthesize human-object interactions, they are largely confined to rigid-object manipulation and lack explicit 4D geometric reasoning. To bridge this gap, we formulate articulated HOI synthesis as a 4D reconstruction problem from monocular video priors: given only a video generated by a diffusion model, we reconstruct a full 4D articulated scene without any 3D supervision. This reconstruction-based approach treats the generated 2D video as supervision for an inverse rendering problem, recovering geometrically consistent and physically plausible 4D scenes that naturally respect contact, articulation, and temporal coherence. We introduce ArtHOI, the first zero-shot framework for articulated human-object interaction synthesis via 4D reconstruction from video priors. Our key designs are: 1) Flow-based part segmentation: leveraging optical flow as a geometric cue to disentangle dynamic from static regions in monocular video; 2) Decoupled reconstruction pipeline: joint optimization of human motion and object articulation is unstable under monocular ambiguity, so we first recover object articulation, then synthesize human motion conditioned on the reconstructed object states. ArtHOI bridges video-based generation and geometry-aware reconstruction, producing interactions that are both semantically aligned and physically grounded. Across diverse articulated scenes (e.g., opening fridges, cabinets, microwaves), ArtHOI significantly outperforms prior methods in contact accuracy, penetration reduction, and articulation fidelity, extending zero-shot interaction synthesis beyond rigid manipulation through reconstruction-informed synthesis.

Modeling spinal motion is fundamental to understanding human biomechanics, yet remains underexplored in computer vision due to the spine's complex multi-joint kinematics and the lack of large-scale 3D annotations. We present a biomechanics-aware keypoint simulation framework that augments existing human pose datasets with anatomically consistent 3D spinal keypoints derived from musculoskeletal modeling. Using this framework, we create the first open dataset, named SIMSPINE, which provides sparse vertebra-level 3D spinal annotations for natural full-body motions in indoor multi-camera capture without external restraints. With 2.14 million frames, this enables data-driven learning of vertebral kinematics from subtle posture variations and bridges the gap between musculoskeletal simulation and computer vision. In addition, we release pretrained baselines covering fine-tuned 2D detectors, monocular 3D pose lifting models, and multi-view reconstruction pipelines, establishing a unified benchmark for biomechanically valid spine motion estimation. Specifically, our 2D spine baselines improve the state-of-the-art from 0.63 to 0.80 AUC in controlled environments, and from 0.91 to 0.93 AP for in-the-wild spine tracking. Together, the simulation framework and SIMSPINE dataset advance research in vision-based biomechanics, motion analysis, and digital human modeling by enabling reproducible, anatomically grounded 3D spine estimation under natural conditions.

Hand-Object Interaction (HOI) synthesis is a cornerstone for animation production and embodied AI. Despite the strong priors of video foundation models, multi-view consistent HOI synthesis remains challenging due to complex hand motions and occlusions. We present HarmoHOI, a unified diffusion framework that jointly and harmoniously generates synchronized multi-view HOI videos and globally aligned 3D point tracks. Our core insight is that robust multi-view consistency fundamentally requires globally aligned 3D geometry and motion. To this end, we propose a Mixture of Multi-view Diffusion Transformer that co-models RGB videos and 3D point tracks. By representing point tracks as pseudo-videos, we align 3D geometric signals with the 2D latent space of foundation models, thereby minimizing the domain gap and easing adaptation of priors. To further ensure geometry consistency, we introduce Global Motion Aligning Diffusion, which refines coarse point tracks into metric-scale, globally aligned 3D trajectories. HarmoHOI enables on-the-fly co-evolution of 2D appearance and 3D motion during denoising. To overcome the scarcity of multi-view HOI data, we employ a hybrid data curriculum learning strategy that successfully transfers generic priors from single-view data to synchronized multi-view generation. Experimental results show that HarmoHOI achieves state-of-the-art performance in visual quality, motion plausibility, and multi-view geometric consistency. Project page available at https://droliven.github.io/HarmoHOI_project.

Existing Stochastic 3D Human Motion Prediction models are fundamentally constrained by hard-coding the skeleton kinematics, severely limiting generalization, preventing cross-dataset training, and requiring complex data retargeting. We introduce EquiFusion, the first kinematics-agnostic model to solve this bottleneck, implementing a latent diffusion model with a permutation equivariant architecture. EquiFusion treats the kinematics' connectivity as an explicit input parameter, ensuring its internal computations are inherently agnostic to joint ordering and graph structure. This novel design enables truly cross-dataset generalization to unseen kinematics and unlocks novel zero-shot directions, such as motion prediction from partial or occluded observations and targeted limb generation. EquiFusion achieves state-of-the-art results on major benchmarks, being up to 75% more compact than previous kinematics-specific methods, while achieving faster training and inference. EquiFusion thus establishes a new, flexible standard for robust human motion prediction. Model and training code are available at https://ceveloper.github.io/publications/equifusion/.

To serve as a scalable data source for embodied AI, world models should act as true simulators that infer interaction dynamics strictly from user actions, rather than mere conditional video generators relying on privileged future object states. In this context, egocentric Human-Object Interaction (HOI) world models are critical for predicting physically grounded first-person rollouts. However, building such models is profoundly challenging due to rapid head motions, severe occlusions, and high-DoF hand articulations that abruptly alter contact topologies. Consequently, existing approaches often circumvent these physics challenges by resorting to conditional video generation with access to known future object trajectories. We introduce EgoHOI, an egocentric HOI world model that breaks away from this shortcut to simulate photorealistic, contact-consistent interactions from action signals alone. To ensure physical accuracy without future-state inputs, EgoHOI distills geometric and kinematic priors from 3D estimates into physics-informed embeddings. These embeddings regularize the egocentric rollouts toward physically valid dynamics. Experiments on the HOT3D dataset demonstrate consistent gains over strong baselines, and ablations validate the effectiveness of our physics-informed design.

Achieving realistic simulations of humans interacting with a wide range of objects has long been a fundamental goal. Extending physics-based motion imitation to complex human-object interactions (HOIs) is challenging due to intricate human-object coupling, variability in object geometries, and artifacts in motion capture data, such as inaccurate contacts and limited hand detail. We introduce InterMimic, a framework that enables a single policy to robustly learn from hours of imperfect MoCap data covering diverse full-body interactions with dynamic and varied objects. Our key insight is to employ a curriculum strategy -- perfect first, then scale up. We first train subject-specific teacher policies to mimic, retarget, and refine motion capture data. Next, we distill these teachers into a student policy, with the teachers acting as online experts providing direct supervision, as well as high-quality references. Notably, we incorporate RL fine-tuning on the student policy to surpass mere demonstration replication and achieve higher-quality solutions. Our experiments demonstrate that InterMimic produces realistic and diverse interactions across multiple HOI datasets. The learned policy generalizes in a zero-shot manner and seamlessly integrates with kinematic generators, elevating the framework from mere imitation to generative modeling of complex human-object interactions.

In an experiment on a turbulent jet, we detect interfacial turbulent layers in a frame that moves, on average, along with the \tnti. This significantly prolongs the observation time of scalar and velocity structures and enables the measurement of two types of Lagrangian coherent structures. One structure, the finite-time Lyapunov field (FTLE), quantifies advective transport barriers of fluid parcels while the other structure highlights barriers of diffusive momentum transport. These two complementary structures depend on large-scale and small-scale motion and are therefore associated with the growth of the turbulent region through engulfment or nibbling, respectively. We detect the \tnti\ from cluster analysis, where we divide the measured scalar field into four clusters. Not only the \tnti\ can be found this way, but also the next, internal, turbulent-turbulent interface. Conditional averages show that these interfaces are correlated with barriers of advective and diffusive transport when the Lagrangian integration time is smaller than the integral time scale. Diffusive structures decorrelate faster since they have a smaller timescale. Conditional averages of these structures at internal turbulent-turbulent interfaces show the same pattern with a more pronounced jump at the interface indicative of a shear layer. This is quite an unexpected outcome, as the internal interface is now defined not by the presence or absence of vorticity, but by conditional vorticity corresponding to two uniform concentration zones. The long-time diffusive momentum flux along Lagrangian paths represents the growth of the turbulent flow into the irrotational domain, a direct demonstration of nibbling. The diffusive flux parallel to the \tnti\ appears to be concentrated in a diffusive superlayer whose width is comparable with the Taylor microscale, which is relatively invariant in time.

Lightweight, controllable, and physically plausible human motion synthesis is crucial for animation, virtual reality, robotics, and human-computer interaction applications. Existing methods often compromise between computational efficiency, physical realism, or spatial controllability. We propose FlexMotion, a novel framework that leverages a computationally lightweight diffusion model operating in the latent space, eliminating the need for physics simulators and enabling fast and efficient training. FlexMotion employs a multimodal pre-trained Transformer encoder-decoder, integrating joint locations, contact forces, joint actuations and muscle activations to ensure the physical plausibility of the generated motions. FlexMotion also introduces a plug-and-play module, which adds spatial controllability over a range of motion parameters (e.g., joint locations, joint actuations, contact forces, and muscle activations). Our framework achieves realistic motion generation with improved efficiency and control, setting a new benchmark for human motion synthesis. We evaluate FlexMotion on extended datasets and demonstrate its superior performance in terms of realism, physical plausibility, and controllability.

Whole-body humanoid loco-manipulation requires coordinating the robot's entire kinematic chain. However, most existing systems typically decouple the upper and lower bodies into separate controllers, limiting such coordination and yielding behaviors similar to those of a wheeled dual-arm platform. In this paper, we ask what it takes to build a whole-body native vision-language-action (VLA) model that maps language and pixels directly to all of the humanoid's degrees of freedom. We conduct a systematic empirical study organized as a roadmap of one-variable-at-a-time experiments across three phases: whole-body teleoperation, VLA model design, and heterogeneous co-training. Our study yields several intriguing findings: a joint-based whole-body teleoperation interface outperforms alternatives that only partially expose the humanoid's degrees of freedom; a VLA pretrained on static and wheeled dual-arm platforms transfers surprisingly well to a humanoid's full action space; and co-training with HuMI, the humanoid analog of UMI, extends the policy to new objects and instructions without additional whole-body teleoperation on those targets. Following this roadmap yields OpenHLM, an open-source recipe for whole-body humanoid loco-manipulation. In a challenging long-horizon task that spans a wide vertical range of the humanoid, OpenHLM outperforms two state-of-the-art humanoid VLA baselines (GR00T N1.6 and Ψ_0) using less than half the total demonstration time. Our code, training data, and model checkpoints are available at [https://openhlm-project.github.io/].

Recent works in robotic manipulation through reinforcement learning (RL) or imitation learning (IL) have shown potential for tackling a range of tasks e.g., opening a drawer or a cupboard. However, these techniques generalize poorly to unseen objects. We conjecture that this is due to the high-dimensional action space for joint control. In this paper, we take an alternative approach and separate the task of learning 'what to do' from 'how to do it' i.e., whole-body control. We pose the RL problem as one of determining the skill dynamics for a disembodied virtual manipulator interacting with articulated objects. The whole-body robotic kinematic control is optimized to execute the high-dimensional joint motion to reach the goals in the workspace. It does so by solving a quadratic programming (QP) model with robotic singularity and kinematic constraints. Our experiments on manipulating complex articulated objects show that the proposed approach is more generalizable to unseen objects with large intra-class variations, outperforming previous approaches. The evaluation results indicate that our approach generates more compliant robotic motion and outperforms the pure RL and IL baselines in task success rates. Additional information and videos are available at https://kl-research.github.io/decoupskill

Dexterous interaction with articulated objects is important for household, assistive, and humanoid manipulation, where multi-finger hands can provide compliant contact patterns beyond parallel-jaw grasping. However, articulated-object manipulation differs from static-object manipulation: the target part cannot be directly actuated, and its motion must emerge through sustained physical hand--handle contact. This makes the transition from object-centric articulated generation to hand-driven dexterous hand--object interaction non-trivial, since geometric trajectory replay or open-loop execution does not model the contact dynamics required to move the articulated part. Moreover, policies trained only for task completion under fixed dynamics can overfit nominal contact loads, especially without tactile or force feedback, and may degrade when the contact load changes. To address these challenges, we present DragMesh-2, a contact-driven framework for dexterous interaction with articulated objects that extends articulated interaction from object-centric generation to hand-driven dexterous hand--object interaction, where articulated motion must arise through physical contact. We further propose PICA, a physically informed contact-aware training mechanism that injects physical signals into policy learning without tactile or force feedback, improving robustness and task success under changing contact loads. Finally, we conduct systematic evaluation across multiple damping conditions and articulated-object categories to study robustness under contact-load variation, and provide a pure-geometry dexterous interaction resource to support future loco-manipulation and humanoid hand--object interaction research. Across seven GAPartNet objects, DragMesh-2 achieves stronger robustness under contact-load variation than the compared methods while maintaining high task success across damping conditions.

Generalizable manipulation skills, which can be composed to tackle long-horizon and complex daily chores, are one of the cornerstones of Embodied AI. However, existing benchmarks, mostly composed of a suite of simulatable environments, are insufficient to push cutting-edge research works because they lack object-level topological and geometric variations, are not based on fully dynamic simulation, or are short of native support for multiple types of manipulation tasks. To this end, we present ManiSkill2, the next generation of the SAPIEN ManiSkill benchmark, to address critical pain points often encountered by researchers when using benchmarks for generalizable manipulation skills. ManiSkill2 includes 20 manipulation task families with 2000+ object models and 4M+ demonstration frames, which cover stationary/mobile-base, single/dual-arm, and rigid/soft-body manipulation tasks with 2D/3D-input data simulated by fully dynamic engines. It defines a unified interface and evaluation protocol to support a wide range of algorithms (e.g., classic sense-plan-act, RL, IL), visual observations (point cloud, RGBD), and controllers (e.g., action type and parameterization). Moreover, it empowers fast visual input learning algorithms so that a CNN-based policy can collect samples at about 2000 FPS with 1 GPU and 16 processes on a regular workstation. It implements a render server infrastructure to allow sharing rendering resources across all environments, thereby significantly reducing memory usage. We open-source all codes of our benchmark (simulator, environments, and baselines) and host an online challenge open to interdisciplinary researchers.

Learning-based controllers, such as diffusion policies and vision-language action models, often generate low-frequency or discontinuous robot state changes. Achieving smooth reference tracking requires a low-level controller that converts high-level targets commands into joint torques, enabling compliant behavior during contact interactions. We present CRISP, a lightweight C++ implementation of compliant Cartesian and joint-space controllers for the ROS2 control standard, designed for seamless integration with high-level learning-based policies as well as teleoperation. The controllers are compatible with any manipulator that exposes a joint-torque interface. Through our Python and Gymnasium interfaces, CRISP provides a unified pipeline for recording data from hardware and simulation and deploying high-level learning-based policies seamlessly, facilitating rapid experimentation. The system has been validated on hardware with the Franka Robotics FR3 and in simulation with the Kuka IIWA14 and Kinova Gen3. Designed for rapid integration, flexible deployment, and real-time performance, our implementation provides a unified pipeline for data collection and policy execution, lowering the barrier to applying learning-based methods on ROS2-compatible manipulators. Detailed documentation is available at the project website - https://utiasDSL.github.io/crisp_controllers.

Hand-Object Interaction (HOI) generation has significant application potential. However, current 3D HOI motion generation approaches heavily rely on predefined 3D object models and lab-captured motion data, limiting generalization capabilities. Meanwhile, HOI video generation methods prioritize pixel-level visual fidelity, often sacrificing physical plausibility. Recognizing that visual appearance and motion patterns share fundamental physical laws in the real world, we propose a novel framework that combines visual priors and dynamic constraints within a synchronized diffusion process to generate the HOI video and motion simultaneously. To integrate the heterogeneous semantics, appearance, and motion features, our method implements tri-modal adaptive modulation for feature aligning, coupled with 3D full-attention for modeling inter- and intra-modal dependencies. Furthermore, we introduce a vision-aware 3D interaction diffusion model that generates explicit 3D interaction sequences directly from the synchronized diffusion outputs, then feeds them back to establish a closed-loop feedback cycle. This architecture eliminates dependencies on predefined object models or explicit pose guidance while significantly enhancing video-motion consistency. Experimental results demonstrate our method's superiority over state-of-the-art approaches in generating high-fidelity, dynamically plausible HOI sequences, with notable generalization capabilities in unseen real-world scenarios. Project page at https://github.com/Droliven/SViMo\_project.

We introduce Yielding Universal Bidigital Interface (YUBI), a finger-aligned gripper designed to enable intuitive, ergonomic, and scalable data collection for bimanual dexterous manipulation. While handheld data collection systems such as Universal Manipulation Interface (UMI) enable affordable data collection, their bulky pistol-grip designs can pose ergonomic and usability challenges for fine-grained, dexterous manipulation tasks. To address this, YUBI presents a distinct design principle: yielding, finger-driven actuation that directly maps human finger movements to gripper jaw motion. Using the YUBI devices, we set up a data collection system with integrated VR-based 6 DoF tracking of the gripper, ensuring high-fidelity trajectory data acquisition. We curate a UMI-based dataset of unprecedented scale: 8,434 hours across 1.20M episodes and 119 tasks. Experiments show that YUBI offers advantages over the UMI gripper in versatility for complex bimanual tasks, dexterity, and operational efficiency. A single policy trained on the YUBI dataset transfers across multiple bimanual robots (UR, Franka, and ELEY) simply by mounting the gripper on each platform, confirming that the collected data are directly executable as policy supervision. We release the gripper hardware, data-collection software, and dataset as one integrated stack, offering the open community a reproducible path to large-scale data acquisition for advancing robotic foundation models.

Generalizable humanoid loco-manipulation poses significant challenges, requiring coordinated whole-body control and precise, contact-rich object manipulation. To address this, this paper introduces HOMIE, a semi-autonomous teleoperation system that combines a reinforcement learning policy for body control mapped to a pedal, an isomorphic exoskeleton arm for arm control, and motion-sensing gloves for hand control, forming a unified cockpit to freely operate humanoids and establish a data flywheel. The policy incorporates novel designs, including an upper-body pose curriculum, a height-tracking reward, and symmetry utilization. These features enable the system to perform walking and squatting to specific heights while seamlessly adapting to arbitrary upper-body poses. The exoskeleton, by eliminating the reliance on inverse dynamics, delivers faster and more precise arm control. The gloves utilize Hall sensors instead of servos, allowing even compact devices to achieve 15 or more degrees of freedom and freely adapt to any model of dexterous hands. Compared to previous teleoperation systems, HOMIE stands out for its exceptional efficiency, completing tasks in half the time; its expanded working range, allowing users to freely reach high and low areas as well as interact with any objects; and its affordability, with a price of just $500. The system is fully open-source, demos and code can be found in our https://homietele.github.io/.

Capturing and maintaining geometric interactions among different body parts is crucial for successful motion retargeting in skinned characters. Existing approaches often overlook body geometries or add a geometry correction stage after skeletal motion retargeting. This results in conflicts between skeleton interaction and geometry correction, leading to issues such as jittery, interpenetration, and contact mismatches. To address these challenges, we introduce a new retargeting framework, MeshRet, which directly models the dense geometric interactions in motion retargeting. Initially, we establish dense mesh correspondences between characters using semantically consistent sensors (SCS), effective across diverse mesh topologies. Subsequently, we develop a novel spatio-temporal representation called the dense mesh interaction (DMI) field. This field, a collection of interacting SCS feature vectors, skillfully captures both contact and non-contact interactions between body geometries. By aligning the DMI field during retargeting, MeshRet not only preserves motion semantics but also prevents self-interpenetration and ensures contact preservation. Extensive experiments on the public Mixamo dataset and our newly-collected ScanRet dataset demonstrate that MeshRet achieves state-of-the-art performance. Code available at https://github.com/abcyzj/MeshRet.

Turning garments right-side out is a challenging manipulation task: it is highly dynamic, entails rapid contact changes, and is subject to severe visual occlusion. We introduce Right-Side-Out, a zero-shot sim-to-real framework that effectively solves this challenge by exploiting task structures. We decompose the task into Drag/Fling to create and stabilize an access opening, followed by Insert&Pull to invert the garment. Each step uses a depth-inferred, keypoint-parameterized bimanual primitive that sharply reduces the action space while preserving robustness. Efficient data generation is enabled by our custom-built, high-fidelity, GPU-parallel Material Point Method (MPM) simulator that models thin-shell deformation and provides robust and efficient contact handling for batched rollouts. Built on the simulator, our fully automated pipeline scales data generation by randomizing garment geometry, material parameters, and viewpoints, producing depth, masks, and per-primitive keypoint labels without any human annotations. With a single depth camera, policies trained entirely in simulation deploy zero-shot on real hardware, achieving up to 81.3% success rate. By employing task decomposition and high fidelity simulation, our framework enables tackling highly dynamic, severely occluded tasks without laborious human demonstrations.

Joint contact forces govern implant longevity, cartilage health, and rehabilitation outcomes, shaping who develops osteoarthritis, who recovers well from joint replacement, and who benefits from biomechanical interventions. Yet they remain measurable only invasively, in a few dozen patients with instrumented implants. I present a physics-free pipeline to predict instantaneous 3D hip and knee contact forces from an uncalibrated monocular video: no markers, force plates, electromyography, subject-specific imaging, or musculoskeletal model. Parametric body meshes are recovered per frame, encoded as kinematic features, and decoded into forces by a transformer whose pose stream is adaptively modulated at every layer by body shape, joint, side, activity text, and self-supervised video tokens (V-JEPA 2), unifying hip and knee in a single model. Under leave-one-subject-out cross-validation across 26 patients and 25 activity categories from the in vivo OrthoLoad database, the pipeline matches the accuracy of subject-specific musculoskeletal simulations (0.32 pm 0.08 BW RMSE for hip; 0.23 pm 0.03 BW for knee) and resolves peak force changes smaller than those reported for gait retraining and osteoarthritis progression. Applied zero-shot to an independent instrumented cohort, it rivals or outperforms prior published methods. Even without curated activity labels, video features alone preserve accuracy and enable end-to-end inference on raw footage. Driven by the predictor, a generative motion prior produces biomechanically plausible variants with reduced peak loading, rediscovering strategies from the predictive simulation literature. This pipeline establishes uncalibrated monocular video as a viable modality for estimating joint loading, opening a path toward retrospective analysis of archived clinical recordings, primary-care screening, and at-home rehabilitation tracking.

Synthesizing whole-body manipulation of articulated objects, including body motion, hand motion, and object motion, is a critical yet challenging task with broad applications in virtual humans and robotics. The core challenges are twofold. First, achieving realistic whole-body motion requires tight coordination between the hands and the rest of the body, as their movements are interdependent during manipulation. Second, articulated object manipulation typically involves high degrees of freedom and demands higher precision, often requiring the fingers to be placed at specific regions to actuate movable parts. To address these challenges, we propose a novel coordinated diffusion noise optimization framework. Specifically, we perform noise-space optimization over three specialized diffusion models for the body, left hand, and right hand, each trained on its own motion dataset to improve generalization. Coordination naturally emerges through gradient flow along the human kinematic chain, allowing the global body posture to adapt in response to hand motion objectives with high fidelity. To further enhance precision in hand-object interaction, we adopt a unified representation based on basis point sets (BPS), where end-effector positions are encoded as distances to the same BPS used for object geometry. This unified representation captures fine-grained spatial relationships between the hand and articulated object parts, and the resulting trajectories serve as targets to guide the optimization of diffusion noise, producing highly accurate interaction motion. We conduct extensive experiments demonstrating that our method outperforms existing approaches in motion quality and physical plausibility, and enables various capabilities such as object pose control, simultaneous walking and manipulation, and whole-body generation from hand-only data.

Industrial robot applications require increasingly flexible systems that non-expert users can easily adapt for varying tasks and environments. However, different adaptations benefit from different interaction modalities. We present an interactive framework that enables robot skill adaptation through three complementary modalities: kinesthetic touch for precise spatial corrections, natural language for high-level semantic modifications, and a graphical web interface for visualizing geometric relations and trajectories, inspecting and adjusting parameters, and editing via-points by drag-and-drop. The framework integrates five components: energy-based human-intention detection, a tool-based LLM architecture (where the LLM selects and parameterizes predefined functions rather than generating code) for safe natural language adaptation, Kernelized Movement Primitives (KMPs) for motion encoding, probabilistic Virtual Fixtures for guided demonstration recording, and ergodic control for surface finishing. We demonstrate that this tool-based LLM architecture generalizes skill adaptation from KMPs to ergodic control, enabling voice-commanded surface finishing. Validation on a 7-DoF torque-controlled robot at the Automatica 2025 trade fair demonstrates the practical applicability of our approach in industrial settings.

We present a novel approach for generating motion primitives for kinodynamic motion planning using diffusion models. The motions generated by our approach are adapted to each problem instance by utilizing problem-specific parameters, allowing for finding solutions faster and of better quality. The diffusion models used in our approach are trained on randomly cut solution trajectories. These trajectories are created by solving randomly generated problem instances with a kinodynamic motion planner. Experimental results show significant improvements up to 30 percent in both computation time and solution quality across varying robot dynamics such as second-order unicycle or car with trailer.

Data-driven approaches have revolutionized 3D vision, enabling transformers to effectively reconstruct and generate static 3D objects. However, generating simulative 4D dynamics -- realistic temporal deformations of static objects under various physical conditions -- remains challenging and often ad hoc, despite its importance in building comprehensive 3D world models. Most existing methods assume a predefined physical model and use system identification to estimate parameters, restricting these methods to specific categories and small-scale datasets. We propose that these restrictions can be overcome by learning a data-driven kinematic state parameterization for object-centric physical systems. Specifically, we learn both a latent space representing all possible states of the object and a decoder that maps any sampled latent to a plausibly deformed shape of the object. We refer to this parameterization as Neural Object Kinematics (NeuROK), and learn a transformer-based encoder-decoder model on a curated large-scale 4D dataset. This formulation and the learned model significantly simplify the generation of simulative dynamics since we only need to consider the dynamics within a low-dimensional latent space from the Lagrangian mechanics' perspective in classical physics. We demonstrate the effectiveness and generality of this neural simulation framework across diverse dynamic object types, showing clear advantages over prior works. Project page: https://chen-geng.com/neurok

We present BimArt, a novel generative approach for synthesizing 3D bimanual hand interactions with articulated objects. Unlike prior works, we do not rely on a reference grasp, a coarse hand trajectory, or separate modes for grasping and articulating. To achieve this, we first generate distance-based contact maps conditioned on the object trajectory with an articulation-aware feature representation, revealing rich bimanual patterns for manipulation. The learned contact prior is then used to guide our hand motion generator, producing diverse and realistic bimanual motions for object movement and articulation. Our work offers key insights into feature representation and contact prior for articulated objects, demonstrating their effectiveness in taming the complex, high-dimensional space of bimanual hand-object interactions. Through comprehensive quantitative experiments, we demonstrate a clear step towards simplified and high-quality hand-object animations that excel over the state-of-the-art in motion quality and diversity.

Representation learning approaches for robotic manipulation have boomed in recent years. Due to the scarcity of in-domain robot data, prevailing methodologies tend to leverage large-scale human video datasets to extract generalizable features for visuomotor policy learning. Despite the progress achieved, prior endeavors disregard the interactive dynamics that capture behavior patterns and physical interaction during the manipulation process, resulting in an inadequate understanding of the relationship between objects and the environment. To this end, we propose a general pre-training pipeline that learns Manipulation by Predicting the Interaction (MPI) and enhances the visual representation.Given a pair of keyframes representing the initial and final states, along with language instructions, our algorithm predicts the transition frame and detects the interaction object, respectively. These two learning objectives achieve superior comprehension towards "how-to-interact" and "where-to-interact". We conduct a comprehensive evaluation of several challenging robotic tasks.The experimental results demonstrate that MPI exhibits remarkable improvement by 10% to 64% compared with previous state-of-the-art in real-world robot platforms as well as simulation environments. Code and checkpoints are publicly shared at https://github.com/OpenDriveLab/MPI.

Whole-arm manipulation involves direct contact with the environment while the robot completes a task by distributing contact across multiple links as contacts form, slide, and break. This setting breaks common implicit assumptions in many learning-based manipulation pipelines: arm configuration tightly couples motion and contact forces, contact state is partially observed under occlusion, and purely learned rollouts can become physically inconsistent under distribution shift because many multi-link contact configurations are sparsely represented in the data. To address this, we propose TACTIC (Tactile and Vision Conditioned Contact-Centric Control), a receding-horizon controller for whole-arm manipulation. TACTIC uses a contact-centric hybrid predictive model that combines RGB-D, distributed tactile sensing, and a compact 2D proximity representation. The model couples a learned, action-conditioned latent dynamics model with analytical kinematics through contact Jacobians, enabling rollouts of future contact configurations and interaction forces. TACTIC integrates these rollouts into a sampling-based MPC planner with contact-aware action sampling: contact Jacobian-based projections steer sampled action sequences toward force-modulating directions, and objectives defined over predicted proximity and interaction forces trade task progress against whole-arm force regulation. We evaluate TACTIC in simulation against state-of-the-art model-based and model-free methods, and perform ablations that isolate the contribution of each design choice. TACTIC consistently outperforms other methods. We further demonstrate real-world performance on a robot with distributed tactile sensing across three whole-arm manipulation tasks that require multi-contact trajectories: turning over and repositioning a manikin, and goal-reaching in a 3D dynamic maze. Website: https://emprise.cs.cornell.edu/tactic

Interlocking brick assemblies provide a standardized yet challenging testbed for contact-rich and long-horizon robotic manipulation, but existing rigid-body simulators do not faithfully capture snap-fit mechanics. We present BrickSim, the first real-time physics-based simulator for interlocking brick assemblies. BrickSim introduces a compact force-based mechanics model for snap-fit connections and solves the resulting internal force distribution using a structured convex quadratic program. Combined with a hybrid architecture that delegates rigid-body dynamics to the underlying physics engine while handling snap-fit mechanics separately, BrickSim enables real-time, high-fidelity simulation of assembly, disassembly, and structural collapse. On 150 real-world assemblies, BrickSim achieves 100% accuracy in static stability prediction with an average solve time of 5 ms. In dynamic drop tests, it also faithfully reproduces real-world structural collapse, precisely mirroring both the occurrence of breakage and the specific breakage locations. Built on Isaac Sim, BrickSim further supports seamless integration with a wide variety of robots and existing pipelines. We demonstrate robotic construction of brick assemblies using BrickSim, highlighting its potential as a foundation for research in dexterous, long-horizon robotic manipulation. BrickSim is open-source, and the code is available at https://github.com/intelligent-control-lab/BrickSim.

Recent video generation research has focused heavily on isolated actions, leaving interactive motions-such as hand-face interactions-largely unexamined. These interactions are essential for emerging biometric authentication systems, which rely on interactive motion-based anti-spoofing approaches. From a security perspective, there is a growing need for large-scale, high-quality interactive videos to train and strengthen authentication models. In this work, we introduce a novel paradigm for animating realistic hand-face interactions. Our approach simultaneously learns spatio-temporal contact dynamics and biomechanically plausible deformation effects, enabling natural interactions where hand movements induce anatomically accurate facial deformations while maintaining collision-free contact. To facilitate this research, we present InterHF, a large-scale hand-face interaction dataset featuring 18 interaction patterns and 90,000 annotated videos. Additionally, we propose InterAnimate, a region-aware diffusion model designed specifically for interaction animation. InterAnimate leverages learnable spatial and temporal latents to effectively capture dynamic interaction priors and integrates a region-aware interaction mechanism that injects these priors into the denoising process. To the best of our knowledge, this work represents the first large-scale effort to systematically study human hand-face interactions. Qualitative and quantitative results show InterAnimate produces highly realistic animations, setting a new benchmark. Code and data will be made public to advance research.

Contact-rich manipulation tasks with stiff frictional elements like connector insertion are difficult to model with rigid-body simulators. In this work, we propose a new approach for modeling these environments by learning a quasi-static contact force model instead of a full simulator. Using a feature vector that contains information about the configuration and control, we find a linear mapping adequately captures the relationship between this feature vector and the sensed contact forces. A novel Linear Model Learning (LML) algorithm is used to solve for the globally optimal mapping in real time without any matrix inversions, resulting in an algorithm that runs in nearly constant time on a GPU as the model size increases. We validate the proposed approach for connector insertion both in simulation and hardware experiments, where the learned model is combined with an optimization-based controller to achieve smooth insertions in the presence of misalignments and uncertainty. Our website featuring videos, code, and more materials is available at https://model-based-plugging.github.io/.

The CAD design process includes a number of repetitive steps when creating assemblies. This issue is compounded when engineering whole product lines or design families, as steps like inserting parts common to all variations, such as fasteners and product-integral base parts, get repeated numerous times. This makes creating designs time-, and as a result, cost-intensive. While many CAD software packages have APIs, the effort of creating use-case specific plugins to automate creation of assemblies usually outweighs the benefit. We developed a plugin for the CAD software package "Fusion 360" which tackles this issue. The plugin adds several graphical interfaces to Fusion 360 that allow parts to be annotated with types, subtype hierarchies to be managed, and requests to synthesize assembly programs for assemblies to be posed. The plugin is use-case agnostic and is able to generate arbitrary open kinematic chain structures. We envision engineers working with CAD software being able to make designed parts reusable and automate the generation of different design alternatives as well as whole product lines.

Most learned dexterous grasp generators relegate contact forces to a downstream verification step, so a kinematically-plausible pose can still violate the conditions for a stable physical grasp. We address this with EquiDexFlow, an SE(3)-equivariant flow-matching model that jointly predicts wrist pose, joint angles, fingertip contacts, surface normals, and contact forces from an object point cloud. Our architecture projects contacts onto the object surface and forces into the Coulomb friction cone by construction, so placement and friction compliance hold without loss penalties. We prove end-to-end SE(3) equivariance and verify it empirically over 200 rotations, with wrist residuals below 0.04^circ and exactly zero joint deviation. Trained on 8,100 force-closure grasps across 81 objects for the 16-DoF Allegro Hand, our model achieves zero friction violations, the best composite score, and the lowest wrench residual among all ablation variants. We retarget decoded fingertip contacts to a 16-DoF LEAP Hand via per-finger inverse kinematics, and our hardware-feasible refinement places every joint at least 5% inside its actuator envelope while preserving wrench balance. On the physical robot, retargeted EquiDexFlow-decoded grasps complete open-loop pick-and-hold trials on all six test objects, with every asymmetric object succeeding at both the canonical pose and a 120^circ co-rotation. Videos, code, and checkpoints are available at https://equidexflow.github.io.

Advances in markerless motion capture are making high-quality biomechanical data increasingly accessible, creating a growing need for scalable downstream analytics. Building a bespoke pipeline for each analysis task is time-consuming, motivating models that can flexibly handle diverse clinical questions within a single framework. Recent work has shown that fine-tuning language models to accept tokenized motion as an additional modality enables descriptive captioning of movement, raising the question of whether these models are also capable of clinically relevant motion understanding, where diverse tasks and annotations provide a natural testbed. We investigate whether such a multimodal motion--language model can answer detailed, clinically meaningful questions about movement. We collected 71 hours of biomechanical data from 750 participants, many with movement impairments, performing tasks commonly used in clinical assessment. To further expand the training dataset, we designed a cross-format tokenizer that directly encodes motion data from heterogeneous formats into a shared latent space without paired data, allowing a second dataset to be incorporated and enabling pooling annotations across datasets. From these tokenized representations, we constructed a multimodal dataset of motion-related question--answer pairs and used it to train BiomechGPT, a multimodal biomechanics--language model. BiomechGPT achieves competitive performance across a range of clinically relevant tasks, with performance scaling with both dataset and model size. It offers a new way for clinicians and researchers to interact with biomechanical data and represents a promising direction for rehabilitation-focused movement analysis. Project page: https://intelligentsensingandrehabilitation.github.io/BiomechGPT/

We present Whole-Body Mobile Manipulation Interface (HoMMI), a data collection and policy learning framework that learns whole-body mobile manipulation directly from robot-free human demonstrations. We augment UMI interfaces with egocentric sensing to capture the global context required for mobile manipulation, enabling portable, robot-free, and scalable data collection. However, naively incorporating egocentric sensing introduces a larger human-to-robot embodiment gap in both observation and action spaces, making policy transfer difficult. We explicitly bridge this gap with a cross-embodiment hand-eye policy design, including an embodiment agnostic visual representation; a relaxed head action representation; and a whole-body controller that realizes hand-eye trajectories through coordinated whole-body motion under robot-specific physical constraints. Together, these enable long-horizon mobile manipulation tasks requiring bimanual and whole-body coordination, navigation, and active perception. Results are best viewed on: https://hommi-robot.github.io

In this paper, we address the problem of tactile sim-to-real policy transfer for contact-rich tasks. Existing methods primarily focus on vision-based sensors and emphasize image rendering quality while providing overly simplistic models of force and shear. Consequently, these models exhibit a large sim-to-real gap for many dexterous tasks. Here, we present HydroShear, a non-holonomic hydroelastic tactile simulator that advances the state-of-the-art by modeling: a) stick-slip transitions, b) path-dependent force and shear build up, and c) full SE(3) object-sensor interactions. HydroShear extends hydroelastic contact models using Signed Distance Functions (SDFs) to track the displacements of the on-surface points of an indenter during physical interaction with the sensor membrane. Our approach generates physics-based, computationally efficient force fields from arbitrary watertight geometries while remaining agnostic to the underlying physics engine. In experiments with GelSight Minis, HydroShear more faithfully reproduces real tactile shear compared to existing methods. This fidelity enables zero-shot sim-to-real transfer of reinforcement learning policies across four tasks: peg insertion, bin packing, book shelving for insertion, and drawer pulling for fine gripper control under slip. Our method achieves a 93% average success rate, outperforming policies trained on tactile images (34%) and alternative shear simulation methods (58%-61%).

Synthesizing realistic human-object interaction motions is a critical problem in VR/AR and human animation. Unlike the commonly studied scenarios involving a single human or hand interacting with one object, we address a more generic multi-body setting with arbitrary numbers of humans, hands, and objects. This complexity introduces significant challenges in synchronizing motions due to the high correlations and mutual influences among bodies. To address these challenges, we introduce SyncDiff, a novel method for multi-body interaction synthesis using a synchronized motion diffusion strategy. SyncDiff employs a single diffusion model to capture the joint distribution of multi-body motions. To enhance motion fidelity, we propose a frequency-domain motion decomposition scheme. Additionally, we introduce a new set of alignment scores to emphasize the synchronization of different body motions. SyncDiff jointly optimizes both data sample likelihood and alignment likelihood through an explicit synchronization strategy. Extensive experiments across four datasets with various multi-body configurations demonstrate the superiority of SyncDiff over existing state-of-the-art motion synthesis methods.

Wheel-legged robots with integrated manipulators hold great promise for mobile manipulation in logistics, industrial automation, and human-robot collaboration. However, unified control of such systems remains challenging due to the redundancy in degrees of freedom, complex wheel-ground contact dynamics, and the need for seamless coordination between locomotion and manipulation. In this work, we present the design and whole-body motion control of an omnidirectional wheel-legged quadrupedal robot equipped with a dexterous manipulator. The proposed platform incorporates independently actuated steering modules and hub-driven wheels, enabling agile omnidirectional locomotion with high maneuverability in structured environments. To address the challenges of contact-rich interaction, we develop a contact-aware whole-body dynamic optimization framework that integrates point-contact modeling for manipulation with line-contact modeling for wheel-ground interactions. A warm-start strategy is introduced to accelerate online optimization, ensuring real-time feasibility for high-dimensional control. Furthermore, a unified kinematic model tailored for the robot's 4WIS-4WID actuation scheme eliminates the need for mode switching across different locomotion strategies, improving control consistency and robustness. Simulation and experimental results validate the effectiveness of the proposed framework, demonstrating agile terrain traversal, high-speed omnidirectional mobility, and precise manipulation under diverse scenarios, underscoring the system's potential for factory automation, urban logistics, and service robotics in semi-structured environments.

Handheld data collection systems, such as the Universal Manipulation Interface (UMI), enable scalable data collection across diverse environments but only capture observed actions rather than the desired actions executed by a robot controller. In contrast, teleoperation captures desired actions directly, but is prohibitively time-consuming to collect. We revisit this trade-off through the lens of action validity across task phases. We observe that handheld trajectories provide valid supervision in tolerant, free-space phases, but lack dynamic feasibility in contact-sensitive phases, where tracking observed trajectories at high stiffness produces large, unsafe contact forces. We study the interaction between these two supervision types for contact-rich manipulation and find that training policies that combine handheld data with a small number of targeted teleoperated demonstrations provide an efficient hybrid strategy. Specifically, rather than teleoperating the entire task, we only collect partial teleoperated demonstrations for task segments where base handheld policies fail. However, naively mixing handheld and teleoperated phase-specific data yields worse performance than training on handheld data alone. To address this mismatch between observed and desired supervision, we propose Bi-modal Routing for Imitation Data via Gated Experts (BRIDGE), a mixture of diffusion policy experts that routes between specialist task phase heads conditioned on the current robot state. Notably, our approach enables task-phase specific use of desired actions during contact sensitive segments and improves success rates over handheld-only baselines by up to 36.7% across three contact-rich manipulation tasks.

Parametric human body models are foundational to human reconstruction, animation, and simulation, yet they remain mutually incompatible: SMPL, SMPL-X, MHR, Anny, and related models each diverge in mesh topology, skeletal structure, shape parameterization, and unit convention, making it impractical to exploit their complementary strengths within a single pipeline. We present SOMA, a unified body layer that bridges these heterogeneous representations through three abstraction layers. Mesh topology abstraction maps any source model's identity to a shared canonical mesh in constant time per vertex. Skeletal abstraction recovers a full set of identity-adapted joint transforms from any body shape, whether in rest pose or an arbitrary posed configuration, in a single closed-form pass, with no iterative optimization or per-model training. Pose abstraction inverts the skinning pipeline to recover unified skeleton rotations directly from posed vertices of any supported model, enabling heterogeneous motion datasets to be consumed without custom retargeting. Together, these layers reduce the O(M^2) per-pair adapter problem to O(M) single-backend connectors, letting practitioners freely mix identity sources and pose data at inference time. The entire pipeline is fully differentiable end-to-end and GPU-accelerated via NVIDIA-Warp.

Human Mesh Recovery (HMR) from an image is a challenging problem because of the inherent ambiguity of the task. Existing HMR methods utilized either temporal information or kinematic relationships to achieve higher accuracy, but there is no method using both. Hence, we propose "Video Inference for Human Mesh Recovery with Vision Transformer (HMR-ViT)" that can take into account both temporal and kinematic information. In HMR-ViT, a Temporal-kinematic Feature Image is constructed using feature vectors obtained from video frames by an image encoder. When generating the feature image, we use a Channel Rearranging Matrix (CRM) so that similar kinematic features could be located spatially close together. The feature image is then further encoded using Vision Transformer, and the SMPL pose and shape parameters are finally inferred using a regression network. Extensive evaluation on the 3DPW and Human3.6M datasets indicates that our method achieves a competitive performance in HMR.

We present HOIDiNi, a text-driven diffusion framework for synthesizing realistic and plausible human-object interaction (HOI). HOI generation is extremely challenging since it induces strict contact accuracies alongside a diverse motion manifold. While current literature trades off between realism and physical correctness, HOIDiNi optimizes directly in the noise space of a pretrained diffusion model using Diffusion Noise Optimization (DNO), achieving both. This is made feasible thanks to our observation that the problem can be separated into two phases: an object-centric phase, primarily making discrete choices of hand-object contact locations, and a human-centric phase that refines the full-body motion to realize this blueprint. This structured approach allows for precise hand-object contact without compromising motion naturalness. Quantitative, qualitative, and subjective evaluations on the GRAB dataset alone clearly indicate HOIDiNi outperforms prior works and baselines in contact accuracy, physical validity, and overall quality. Our results demonstrate the ability to generate complex, controllable interactions, including grasping, placing, and full-body coordination, driven solely by textual prompts. https://hoidini.github.io.

UMI-style interfaces enable scalable robot learning, but existing systems remain largely visuomotor, relying primarily on RGB observations and trajectory while providing only limited access to physical interaction signals. This becomes a fundamental limitation in contact-rich manipulation, where success depends on contact dynamics such as tactile interaction, internal grasping force, and external interaction wrench that are difficult to infer from vision alone. We present OmniUMI, a unified framework for physically grounded robot learning via human-aligned multimodal interaction. OmniUMI synchronously captures RGB, depth, trajectory, tactile sensing, internal grasping force, and external interaction wrench within a compact handheld system, while maintaining collection--deployment consistency through a shared embodiment design. To support human-aligned demonstration, OmniUMI enables natural perception and modulation of internal grasping force, external interaction wrench, and tactile interaction through bilateral gripper feedback and the handheld embodiment. Built on this interface, we extend diffusion policy with visual, tactile, and force-related observations, and deploy the learned policy through impedance-based execution for unified regulation of motion and contact behavior. Experiments demonstrate reliable sensing and strong downstream performance on force-sensitive pick-and-place, interactive surface erasing, and tactile-informed selective release. Overall, OmniUMI combines physically grounded multimodal data acquisition with human-aligned interaction, providing a scalable foundation for learning contact-rich manipulation.

We address the task of generating physically accurate and visually faithful 4D Human-Object Interaction (HOI). Given a static 3D human and target object represented as 3D Gaussian Splats (3DGS), our goal is to synthesize dynamic scenes where the human actively engages with the object through actions, such as punching or kicking, in accordance with a given input text. To this end, we introduce PhyGenHOI, a novel framework that couples generative human motion with an explicit physical object simulation. We model the human as a semantic agent driven by a Motion Diffusion Model (MDM) and the object as a physical agent simulated via the Material Point Method (MPM), utilizing 3D Gaussians as a unified, differentiable representation. We supervise their interaction through three coupled mechanisms: (1) A Windowed Attraction Loss that temporally synchronizes generative motion to intercept the object; (2) A Contact-Driven Re-simulation step that triggers physically consistent momentum transfer upon impact; and (3) A Masked Video-SDS objective that injects video-based priors to enhance contact fidelity. Experiments show PhyGenHOI generates physically consistent 4D HOI across diverse actions, humans, and objects, outperforming baselines. Project page and videos: https://omerbenishu.github.io/PhyGenHOI/

Navigation and manipulation are core capabilities in Embodied AI, yet training agents with these capabilities in the real world faces high costs and time complexity. Therefore, sim-to-real transfer has emerged as a key approach, yet the sim-to-real gap persists. This survey examines how physics simulators address this gap by analyzing their properties overlooked in previous surveys. We also analyze their features for navigation and manipulation tasks, along with hardware requirements. Additionally, we offer a resource with benchmark datasets, metrics, simulation platforms, and cutting-edge methods-such as world models and geometric equivariance-to help researchers select suitable tools while accounting for hardware constraints.

Path-velocity decomposition is an intuitive yet powerful approach to address the complexity of kinodynamic motion planning. The difficult trajectory planning problem is solved in two separate, simpler, steps: first, find a path in the configuration space that satisfies the geometric constraints (path planning), and second, find a time-parameterization of that path satisfying the kinodynamic constraints. A fundamental requirement is that the path found in the first step should be time-parameterizable. Most existing works fulfill this requirement by enforcing quasi-static constraints in the path planning step, resulting in an important loss in completeness. We propose a method that enables path-velocity decomposition to discover truly dynamic motions, i.e. motions that are not quasi-statically executable. At the heart of the proposed method is a new algorithm -- Admissible Velocity Propagation -- which, given a path and an interval of reachable velocities at the beginning of that path, computes exactly and efficiently the interval of all the velocities the system can reach after traversing the path while respecting the system kinodynamic constraints. Combining this algorithm with usual sampling-based planners then gives rise to a family of new trajectory planners that can appropriately handle kinodynamic constraints while retaining the advantages associated with path-velocity decomposition. We demonstrate the efficiency of the proposed method on some difficult kinodynamic planning problems, where, in particular, quasi-static methods are guaranteed to fail.

Safety verification in Computer Numerical Control (CNC) machining has traditionally relied on simulation-based methods that require repetitive tests when requirements change. This paper introduces a formal verification framework that conceptualizes the physical CNC workspace as a Spatial Heap, treating physical occupancy as a managed logical resource. Central to our approach is a Parser-Prover Handshake that decouples machine kinematics from formal logic. By mapping tool trajectories and safety buffers into a discrete spatial model prior to evaluation, the framework enables the use of Separation Logic (SL) to verify safety via formal triples. Within this model, physical collisions are redefined as logical Spatial Data Races, detected through the failure of the separating conjunction to establish disjointness. Furthermore, we extend the methodology to collaborative environments using Concurrent Separation Logic (CSL), where physical hand-offs are verified as formal ownership transfers. Additionally, the framework scales to multi-axis kinematics (e.g., 5-axis Table-Table configurations) by treating the workpiece as a dynamically mutable spatial resource. By serving as a complement to traditional geometric simulation, this approach reduces the number of required iterative test cycles, offering a foundation for autonomous, less-collision manufacturing.

Humanoid whole-body control requires adapting to diverse tasks such as navigation, loco-manipulation, and tabletop manipulation, each demanding a different mode of control. For example, navigation relies on root velocity tracking, while tabletop manipulation prioritizes upper-body joint angle tracking. Existing approaches typically train individual policies tailored to a specific command space, limiting their transferability across modes. We present the key insight that full-body kinematic motion imitation can serve as a common abstraction for all these tasks and provide general-purpose motor skills for learning multiple modes of whole-body control. Building on this, we propose HOVER (Humanoid Versatile Controller), a multi-mode policy distillation framework that consolidates diverse control modes into a unified policy. HOVER enables seamless transitions between control modes while preserving the distinct advantages of each, offering a robust and scalable solution for humanoid control across a wide range of modes. By eliminating the need for policy retraining for each control mode, our approach improves efficiency and flexibility for future humanoid applications.

Modeling the hand-object (HO) interaction not only requires estimation of the HO pose, but also pays attention to the contact due to their interaction. Significant progress has been made in estimating hand and object separately with deep learning methods, simultaneous HO pose estimation and contact modeling has not yet been fully explored. In this paper, we present an explicit contact representation namely Contact Potential Field (CPF), and a learning-fitting hybrid framework namely MIHO to Modeling the Interaction of Hand and Object. In CPF, we treat each contacting HO vertex pair as a spring-mass system. Hence the whole system forms a potential field with minimal elastic energy at the grasp position. Extensive experiments on the two commonly used benchmarks have demonstrated that our method can achieve state-of-the-art in several reconstruction metrics, and allow us to produce more physically plausible HO pose even when the ground-truth exhibits severe interpenetration or disjointedness. Our code is available at https://github.com/lixiny/CPF.

This paper tackles the problem of physics-aware human motion synthesis in a dynamic scene. Unlike existing works which mainly tend to generate physically unrealistic motions due to limited contact modeling, typically restricted to hands, in this paper, we introduce a physics-aware human motion generation framework that explicitly models the full spectrum of human-related forces, including human-object, human-scene, and internal body dynamics.~Our method imposes soft physical constraints to maintain force and torque balance, ensuring physically grounded motion synthesis. We further propose a novel continuous distance-based force model that generalizes contact modeling to arbitrary surfaces, capturing interactions not only with static environments but also with dynamic, moving objects. Extensive experiments show that our approach significantly improves physical plausibility and generalizes well to complex scenes, setting a new benchmark for physically consistent human motion generation.

We present RoboManipBaselines, an open-source software framework for imitation learning research in robotic manipulation. The framework supports the entire imitation learning pipeline, including data collection, policy training, and rollout, across both simulation and real-world environments. Its design emphasizes integration through a consistent workflow, generality across diverse environments and robot platforms, extensibility for easily adding new robots, tasks, and policies, and reproducibility through evaluations using publicly available datasets. RoboManipBaselines systematically implements the core components of imitation learning: environment, dataset, and policy. Through a unified interface, the framework supports multiple simulators and real robot environments, as well as multimodal sensors and a wide variety of policy models. We further present benchmark evaluations in both simulation and real-world environments and introduce several research applications, including data augmentation, integration with tactile models, interactive robotic systems, 3D sensing evaluation, and hardware extensions. These results demonstrate that RoboManipBaselines provides a useful foundation for advancing research and experimental validation in robotic manipulation using imitation learning. https://isri-aist.github.io/RoboManipBaselines-ProjectPage

The rising number of the elderly incurs growing concern about healthcare, and in particular rehabilitation healthcare. Assistive technology and assistive robotics in particular may help to improve this process. We develop a robot coach capable of demonstrating rehabilitation exercises to patients, watch a patient carry out the exercises and give him feedback so as to improve his performance and encourage him. The HRI of the system is based on our study with a team of rehabilitation therapists and with the target population.The system relies on human motion analysis. We develop a method for learning a probabilistic representation of ideal movements from expert demonstrations. A Gaussian Mixture Model is employed from position and orientation features captured using a Microsoft Kinect v2. For assessing patients' movements, we propose a real-time multi-level analysis to both temporally and spatially identify and explain body part errors. This analysis combined with a classification algorithm allows the robot to provide coaching advice to make the patient improve his movements. The evaluation on three rehabilitation exercises shows the potential of the proposed approach for learning and assessing kinaesthetic movements.

Physics simulation for contact-rich robotics is often bottlenecked by contact resolution: mainstream engines enforce non-penetration and Coulomb friction via complementarity constraints or constrained optimization, requiring per-step iterative solves whose cost grows superlinearly with contact density. We present ComFree-Sim, a GPU-parallelized analytical contact physics engine built on complementarity-free contact modeling. ComFree-Sim computes contact impulses in closed form via an impedance-style prediction--correction update in the dual cone of Coulomb friction. Contact computation decouples across contact pairs and becomes separable across cone facets, mapping naturally to GPU kernels and yielding near-linear runtime scaling with the number of contacts. We further extend the formulation to a unified 6D contact model capturing tangential, torsional, and rolling friction, and introduce a practical dual-cone impedance heuristic. ComFree-Sim is implemented in Warp and exposed through a MuJoCo-compatible interface as a drop-in backend alternative to MuJoCo Warp (MJWarp). Experiments benchmark penetration, friction behaviors, stability, and simulation runtime scaling against MJWarp, demonstrating near-linear scaling and 2--3 times higher throughput in dense contact scenes with comparable physical fidelity. We deploy ComFree-Sim in real-time MPC for in-hand dexterous manipulation on a real-world multi-fingered LEAP hand and in dynamics-aware motion retargeting, demonstrating that low-latency simulation yields higher closed-loop success rates and enables practical high-frequency control in contact-rich tasks.

While generative models have excelled at creating static 3D content, the pursuit of systems that understand how objects move and respond to interactions remains a fundamental challenge. Current methods for articulated motion lie at a crossroads: they are either physically consistent but too slow for real-time use, or generative but violate basic kinematic constraints. We present DragMesh, a robust framework for real-time interactive 3D articulation built around a lightweight motion generation core. Our core contribution is a novel decoupled kinematic reasoning and motion generation framework. First, we infer the latent joint parameters by decoupling semantic intent reasoning (which determines the joint type) from geometric regression (which determines the axis and origin using our Kinematics Prediction Network (KPP-Net)). Second, to leverage the compact, continuous, and singularity-free properties of dual quaternions for representing rigid body motion, we develop a novel Dual Quaternion VAE (DQ-VAE). This DQ-VAE receives these predicted priors, along with the original user drag, to generate a complete, plausible motion trajectory. To ensure strict adherence to kinematics, we inject the joint priors at every layer of the DQ-VAE's non-autoregressive Transformer decoder using FiLM (Feature-wise Linear Modulation) conditioning. This persistent, multi-scale guidance is complemented by a numerically-stable cross-product loss to guarantee axis alignment. This decoupled design allows DragMesh to achieve real-time performance and enables plausible, generative articulation on novel objects without retraining, offering a practical step toward generative 3D intelligence. Code: https://github.com/AIGeeksGroup/DragMesh. Website: https://aigeeksgroup.github.io/DragMesh.

Fine-grained capturing of 3D HOI boosts human activity understanding and facilitates downstream visual tasks, including action recognition, holistic scene reconstruction, and human motion synthesis. Despite its significance, existing works mostly assume that humans interact with rigid objects using only a few body parts, limiting their scope. In this paper, we address the challenging problem of f-AHOI, wherein the whole human bodies interact with articulated objects, whose parts are connected by movable joints. We present CHAIRS, a large-scale motion-captured f-AHOI dataset, consisting of 16.2 hours of versatile interactions between 46 participants and 81 articulated and rigid sittable objects. CHAIRS provides 3D meshes of both humans and articulated objects during the entire interactive process, as well as realistic and physically plausible full-body interactions. We show the value of CHAIRS with object pose estimation. By learning the geometrical relationships in HOI, we devise the very first model that leverage human pose estimation to tackle the estimation of articulated object poses and shapes during whole-body interactions. Given an image and an estimated human pose, our model first reconstructs the pose and shape of the object, then optimizes the reconstruction according to a learned interaction prior. Under both evaluation settings (e.g., with or without the knowledge of objects' geometries/structures), our model significantly outperforms baselines. We hope CHAIRS will promote the community towards finer-grained interaction understanding. We will make the data/code publicly available.

Generating accurate and realistic virtual human movements in real-time is of high importance for a variety of applications in computer graphics, interactive virtual environments, robotics, and biomechanics. This paper introduces a novel real-time inverse kinematics (IK) solver specifically designed for realistic human-like movement generation. Leveraging the automatic differentiation and just-in-time compilation of TensorFlow, the proposed solver efficiently handles complex articulated human skeletons with high degrees of freedom. By treating forward and inverse kinematics as differentiable operations, our method effectively addresses common challenges such as error accumulation and complicated joint limits in multi-constrained problems, which are critical for realistic human motion modeling. We demonstrate the solver's effectiveness on the SMPLX human skeleton model, evaluating its performance against widely used iterative-based IK algorithms, like Cyclic Coordinate Descent (CCD), FABRIK, and the nonlinear optimization algorithm IPOPT. Our experiments cover both simple end-effector tasks and sophisticated, multi-constrained problems with realistic joint limits. Results indicate that our IK solver achieves real-time performance, exhibiting rapid convergence, minimal computational overhead per iteration, and improved success rates compared to existing methods. The project code is available at https://github.com/hvoss-techfak/TF-JAX-IK

We present Articulated Kinematics Distillation (AKD), a framework for generating high-fidelity character animations by merging the strengths of skeleton-based animation and modern generative models. AKD uses a skeleton-based representation for rigged 3D assets, drastically reducing the Degrees of Freedom (DoFs) by focusing on joint-level control, which allows for efficient, consistent motion synthesis. Through Score Distillation Sampling (SDS) with pre-trained video diffusion models, AKD distills complex, articulated motions while maintaining structural integrity, overcoming challenges faced by 4D neural deformation fields in preserving shape consistency. This approach is naturally compatible with physics-based simulation, ensuring physically plausible interactions. Experiments show that AKD achieves superior 3D consistency and motion quality compared with existing works on text-to-4D generation. Project page: https://research.nvidia.com/labs/dir/akd/

Supervised learning models for precise tracking of hand-object interactions (HOI) in 3D require large amounts of annotated data for training. Moreover, it is not intuitive for non-experts to label 3D ground truth (e.g. 6DoF object pose) on 2D images. To address these issues, we present "blender-hoisynth", an interactive synthetic data generator based on the Blender software. Blender-hoisynth can scalably generate and automatically annotate visual HOI training data. Other competing approaches usually generate synthetic HOI data compeletely without human input. While this may be beneficial in some scenarios, HOI applications inherently necessitate direct control over the HOIs as an expression of human intent. With blender-hoisynth, it is possible for users to interact with objects via virtual hands using standard Virtual Reality hardware. The synthetically generated data are characterized by a high degree of photorealism and contain visually plausible and physically realistic videos of hands grasping objects and moving them around in 3D. To demonstrate the efficacy of our data generation, we replace large parts of the training data in the well-known DexYCB dataset with hoisynth data and train a state-of-the-art HOI reconstruction model with it. We show that there is no significant degradation in the model performance despite the data replacement.

Video is a scalable observation of physical dynamics: it captures how objects move, how contact unfolds, and how scenes evolve under interaction -- all without requiring robot action labels. Yet translating this temporal structure into reliable robotic control remains an open challenge, because video lacks action supervision and differs from robot experience in embodiment, viewpoint, and physical constraints. This survey reviews methods that exploit non-action-annotated temporal video to learn control interfaces for robotic manipulation. We introduce an interface-centric taxonomy organized by where the video-to-control interface is constructed and what control properties it enables, identifying three families: direct video--action policies, which keep the interface implicit; latent-action methods, which route temporal structure through a compact learned intermediate; and explicit visual interfaces, which predict interpretable targets for downstream control. For each family, we analyze control-integration properties -- how the loop is closed, what can be verified before execution, and where failures enter. A cross-family synthesis reveals that the most pressing open challenges center on the robotics integration layer -- the mechanisms that connect video-derived predictions to dependable robot behavior -- and we outline research directions toward closing this gap.

We introduce PhysGaussian, a new method that seamlessly integrates physically grounded Newtonian dynamics within 3D Gaussians to achieve high-quality novel motion synthesis. Employing a custom Material Point Method (MPM), our approach enriches 3D Gaussian kernels with physically meaningful kinematic deformation and mechanical stress attributes, all evolved in line with continuum mechanics principles. A defining characteristic of our method is the seamless integration between physical simulation and visual rendering: both components utilize the same 3D Gaussian kernels as their discrete representations. This negates the necessity for triangle/tetrahedron meshing, marching cubes, "cage meshes," or any other geometry embedding, highlighting the principle of "what you see is what you simulate (WS^2)." Our method demonstrates exceptional versatility across a wide variety of materials--including elastic entities, metals, non-Newtonian fluids, and granular materials--showcasing its strong capabilities in creating diverse visual content with novel viewpoints and movements. Our project page is at: https://xpandora.github.io/PhysGaussian/

Synthesizing diverse and physically plausible Human-Scene Interactions (HSI) is pivotal for both computer animation and embodied AI. Despite encouraging progress, current methods mainly focus on developing separate controllers, each specialized for a specific interaction task. This significantly hinders the ability to tackle a wide variety of challenging HSI tasks that require the integration of multiple skills, e.g., sitting down while carrying an object. To address this issue, we present TokenHSI, a single, unified transformer-based policy capable of multi-skill unification and flexible adaptation. The key insight is to model the humanoid proprioception as a separate shared token and combine it with distinct task tokens via a masking mechanism. Such a unified policy enables effective knowledge sharing across skills, thereby facilitating the multi-task training. Moreover, our policy architecture supports variable length inputs, enabling flexible adaptation of learned skills to new scenarios. By training additional task tokenizers, we can not only modify the geometries of interaction targets but also coordinate multiple skills to address complex tasks. The experiments demonstrate that our approach can significantly improve versatility, adaptability, and extensibility in various HSI tasks. Website: https://liangpan99.github.io/TokenHSI/

Text-conditioned motion synthesis has made remarkable progress with the emergence of diffusion models. However, the majority of these motion diffusion models are primarily designed for a single character and overlook multi-human interactions. In our approach, we strive to explore this problem by synthesizing human motion with interactions for a group of characters of any size in a zero-shot manner. The key aspect of our approach is the adaptation of human-wise interactions as pairs of human joints that can be either in contact or separated by a desired distance. In contrast to existing methods that necessitate training motion generation models on multi-human motion datasets with a fixed number of characters, our approach inherently possesses the flexibility to model human interactions involving an arbitrary number of individuals, thereby transcending the limitations imposed by the training data. We introduce a novel controllable motion generation method, InterControl, to encourage the synthesized motions maintaining the desired distance between joint pairs. It consists of a motion controller and an inverse kinematics guidance module that realistically and accurately aligns the joints of synthesized characters to the desired location. Furthermore, we demonstrate that the distance between joint pairs for human-wise interactions can be generated using an off-the-shelf Large Language Model (LLM). Experimental results highlight the capability of our framework to generate interactions with multiple human characters and its potential to work with off-the-shelf physics-based character simulators.

Articulated objects are central to interactive 3D applications, including embodied AI, robotics, and VR/AR, where functional part decomposition and kinematic motion are essential. Yet producing high-fidelity articulated assets remains difficult to scale because it requires reliable part decomposition and kinematic rigging. Existing approaches largely fall into two paradigms: optimization-based reconstruction or distillation, which can be accurate but often takes tens of minutes to hours per instance, and inference-time methods that rely on template or part retrieval, producing plausible results that may not match the specific structure and appearance in the input observation. We introduce a part-centric generative framework for articulated object creation that synthesizes part geometry, composition, and articulation under explicit part-aware conditioning. Our representation models an object as a set of movable parts, each encoded by latent tokens augmented with part identity and articulation cues. Conditioned on a single image, the model generates articulated 3D assets that preserve instance-level correspondence while maintaining valid part structure and motion. The resulting approach avoids per-instance optimization, enables fast feed-forward inference, and supports controllable assembly and articulation, which are important for embodied interaction. Experiments on common articulated categories (e.g., drawers and doors) show improved input consistency, part accuracy, and articulation plausibility over optimization-based and retrieval-driven baselines, while substantially reducing inference time.

Robotic manipulators are increasingly used to assist individuals with mobility impairments in object retrieval. However, the predominant joystick-based control interfaces can be challenging due to high precision requirements and unintuitive reference frames. Recent advances in human-robot interaction have explored alternative modalities, yet many solutions still rely on external screens or restrictive control schemes, limiting their intuitiveness and accessibility. To address these challenges, we present an egocentric, gaze-guided robotic manipulation interface that leverages a wearable Mixed Reality (MR) headset. Our system enables users to interact seamlessly with real-world objects using natural gaze fixation from a first-person perspective, while providing augmented visual cues to confirm intent and leveraging a pretrained vision model and robotic arm for intent recognition and object manipulation. Experimental results demonstrate that our approach significantly improves manipulation accuracy, reduces system latency, and achieves single-pass intention and object recognition accuracy greater than 88% across multiple real-world scenarios. These results demonstrate the system's effectiveness in enhancing intuitiveness and accessibility, underscoring its practical significance for assistive robotics applications.

Mimicking realistic dynamics in 3D garment animations is a challenging task due to the complex nature of multi-layered garments and the variety of outer forces involved. Existing approaches mostly focus on single-layered garments driven by only human bodies and struggle to handle general scenarios. In this paper, we propose a novel data-driven method, called LayersNet, to model garment-level animations as particle-wise interactions in a micro physics system. We improve simulation efficiency by representing garments as patch-level particles in a two-level structural hierarchy. Moreover, we introduce a novel Rotation Equivalent Transformation that leverages the rotation invariance and additivity of physics systems to better model outer forces. To verify the effectiveness of our approach and bridge the gap between experimental environments and real-world scenarios, we introduce a new challenging dataset, D-LAYERS, containing 700K frames of dynamics of 4,900 different combinations of multi-layered garments driven by both human bodies and randomly sampled wind. Our experiments show that LayersNet achieves superior performance both quantitatively and qualitatively. We will make the dataset and code publicly available at https://mmlab-ntu.github.io/project/layersnet/index.html .

Video Diffusion Models (VDMs) offer a promising approach for simulating dynamic scenes and environments, with broad applications in robotics and media generation. However, existing models often generate temporally incoherent content that violates basic physical intuition, significantly limiting their practical applicability. We propose PhysAlign, an efficient framework for physics-coherent image-to-video (I2V) generation that explicitly addresses this limitation. To overcome the critical scarcity of physics-annotated videos, we first construct a fully controllable synthetic data generation pipeline based on rigid-body simulation, yielding a highly-curated dataset with accurate, fine-grained physics and 3D annotations. Leveraging this data, PhysAlign constructs a unified physical latent space by coupling explicit 3D geometry constraints with a Gram-based spatio-temporal relational alignment that extracts kinematic priors from video foundation models. Extensive experiments demonstrate that PhysAlign significantly outperforms existing VDMs on tasks requiring complex physical reasoning and temporal stability, without compromising zero-shot visual quality. PhysAlign shows the potential to bridge the gap between raw visual synthesis and rigid-body kinematics, establishing a practical paradigm for genuinely physics-grounded video generation. The project page is available at https://physalign.github.io/PhysAlign.

We present a dataset for force-grounded, cross-view articulated manipulation that couples what is seen with what is done and what is felt during real human interaction. The dataset contains 3048 sequences across 381 articulated objects in 38 environments. Each object is operated in four embodiments - (i) human hand, (ii) human hand with a wrist-mounted camera, (iii) handheld UMI gripper, and (iv) a custom Hoi! gripper, where the tool embodiment provides end-effector forces and tactile sensing. Our dataset offers a holistic view of interaction understanding from video, enabling researchers to evaluate how well methods transfer between human and robotic viewpoints, but also investigate underexplored modalities such as interaction forces. The Project Website can be found at https://timengelbracht.github.io/Hoi-Dataset-Website/.

The recent popularity of robotics, combined with the steadily decreasing cost of robotic hardware, has lowered the entry barrier to robotics research and enabled rapid advancements in the field. One of the primary examples is the Unitree Go2 quadruped robot, which is often used by researchers in the areas of locomotion, navigation, control, and others. Many researchers use the Go2 robot in combination with techniques like imitation learning, reinforcement learning, and behavioral cloning to allow machine learning systems to take full control of the robot. At the same time, many of those techniques require demonstration data consisting of the robot's kinematics information and actions applied to the motors. Obtaining such data is difficult, requires building complex pipelines, and can take significant time. To aid in those kinds of efforts, we present Kine2Go - a dataset with 800 diverse gait kinematics trajectory motion data for the Unitree Go2 robot, derived from 40 distinct policies. Our pipeline accepts data from various quadruped morphologies and translates them to a Go2-compatible format. Then we use Reinforcement Learning to train policies following a given motion, and finally we gather data from those policies, which grants robust, perturbed kinematic data with corresponding motor-level actions.

This work studies the challenge of transfer animations between characters whose skeletal topologies differ substantially. While many techniques have advanced retargeting techniques in decades, transfer motions across diverse topologies remains less-explored. The primary obstacle lies in the inherent topological inconsistency between source and target skeletons, which restricts the establishment of straightforward one-to-one bone correspondences. Besides, the current lack of large-scale paired motion datasets spanning different topological structures severely constrains the development of data-driven approaches. To address these limitations, we introduce Motion2Motion, a novel, training-free framework. Simply yet effectively, Motion2Motion works with only one or a few example motions on the target skeleton, by accessing a sparse set of bone correspondences between the source and target skeletons. Through comprehensive qualitative and quantitative evaluations, we demonstrate that Motion2Motion achieves efficient and reliable performance in both similar-skeleton and cross-species skeleton transfer scenarios. The practical utility of our approach is further evidenced by its successful integration in downstream applications and user interfaces, highlighting its potential for industrial applications. Code and data are available at https://lhchen.top/Motion2Motion.

Injury to the cervical spinal cord can cause quadriplegia, impairing muscle function in all four limbs. People with impaired hand function and mobility encounter significant difficulties in carrying out essential self-care and household tasks. Despite the impairment of their neural drive, their volitional myoelectric activity is often partially preserved. High-density electromyography (HDEMG) can detect this myoelectric activity, which can serve as control inputs to assistive devices. Previous HDEMG-controlled robotic interfaces have primarily been limited to controlling table-mounted robot arms. These have constrained reach capabilities. Instead, the ability to control mobile manipulators, which have no such workspace constraints, could allow individuals with quadriplegia to perform a greater variety of assistive tasks, thus restoring independence and reducing caregiver workload. In this study, we introduce a non-invasive wearable HDEMG interface with real-time myoelectric hand gesture recognition, enabling both coarse and fine control over the intricate mobility and manipulation functionalities of an 8 degree-of-freedom mobile manipulator. Our evaluation, involving 13 participants engaging in challenging self-care and household activities, demonstrates the potential of our wearable HDEMG system to profoundly enhance user independence by enabling non-invasive control of a mobile manipulator.

In manufacturing sectors such as textiles and electronics, manual processes are a fundamental part of production. The analysis and monitoring of the processes is necessary for efficient production design. Traditional methods for analyzing manual processes are complex, expensive, and inflexible. Compared to established approaches such as Methods-Time-Measurement (MTM), machine learning (ML) methods promise: Higher flexibility, self-sufficient & permanent use, lower costs. In this work, based on a video stream, the current motion class in a manual assembly process is detected. With information on the current motion, Key-Performance-Indicators (KPIs) can be derived easily. A skeleton-based action recognition approach is taken, as this field recently shows major success in machine vision tasks. For skeleton-based action recognition in manual assembly, no sufficient pre-work could be found. Therefore, a ML pipeline is developed, to enable extensive research on different (pre-) processing methods and neural nets. Suitable well generalizing approaches are found, proving the potential of ML to enhance analyzation of manual processes. Models detect the current motion, performed by an operator in manual assembly, but the results can be transferred to all kinds of manual processes.

Reliable odometry for legged robots without cameras or LiDAR remains challenging due to IMU drift and noisy joint velocity sensing. This paper presents a purely proprioceptive state estimator that uses only IMU and motor measurements to jointly estimate body pose and velocity, with a unified formulation applicable to biped, quadruped, and wheel-legged robots. The key idea is to treat each contacting leg as a kinematic anchor: joint-torque--based foot wrench estimation selects reliable contacts, and the corresponding footfall positions provide intermittent world-frame constraints that suppress long-term drift. To prevent elevation drift during extended traversal, we introduce a lightweight height clustering and time-decay correction that snaps newly recorded footfall heights to previously observed support planes. To improve foot velocity observations under encoder quantization, we apply an inverse-kinematics cubature Kalman filter that directly filters foot-end velocities from joint angles and velocities. The implementation further mitigates yaw drift through multi-contact geometric consistency and degrades gracefully to a kinematics-derived heading reference when IMU yaw constraints are unavailable or unreliable. We evaluate the method on four quadruped platforms (three Astrall robots and a Unitree Go2 EDU) using closed-loop trajectories. On Astrall point-foot robot~A, a sim200\,m horizontal loop and a sim15\,m vertical loop return with 0.1638\,m and 0.219\,m error, respectively; on wheel-legged robot~B, the corresponding errors are 0.2264\,m and 0.199\,m. On wheel-legged robot~C, a sim700\,m horizontal loop yields 7.68\,m error and a sim20\,m vertical loop yields 0.540\,m error. Unitree Go2 EDU closes a sim120\,m horizontal loop with 2.2138\,m error and a sim8\,m vertical loop with less than 0.1\,m vertical error. github.com/ShineMinxing/Ros2Go2Estimator.git

In this paper, we introduce tensor involved peridynamics, a unified framework for simulating both isotropic and anisotropic materials. While traditional peridynamics models effectively simulate isotropic materials, they face challenges with anisotropic materials and are prone to instability caused by zero energy modes. Our novel model extend the linear bond based peridynamics framework by incorporating the elastic tensor into the micrmodulus function, thereby ensuring stability for anisotropic materials without the need for additional corrections. For isotropic materials. the model mantains compatibility with conventional bond based peridynamics, assuming Possion's rations of 1/4 in 3D and 1/3 in 2D.Numerical experiments confirm the model's stability and accuracy across various scenarios. Additionally, we introduce a damage model for isotropic materials. validating its performance in predicting crack propagation paths in a 2D plate. The results show superior alignment with experimental date compared to traditional model.

3D modeling is moving from virtual to physical. Existing 3D generation primarily emphasizes geometries and textures while neglecting physical-grounded modeling. Consequently, despite the rapid development of 3D generative models, the synthesized 3D assets often overlook rich and important physical properties, hampering their real-world application in physical domains like simulation and embodied AI. As an initial attempt to address this challenge, we propose PhysX, an end-to-end paradigm for physical-grounded 3D asset generation. 1) To bridge the critical gap in physics-annotated 3D datasets, we present PhysXNet - the first physics-grounded 3D dataset systematically annotated across five foundational dimensions: absolute scale, material, affordance, kinematics, and function description. In particular, we devise a scalable human-in-the-loop annotation pipeline based on vision-language models, which enables efficient creation of physics-first assets from raw 3D assets.2) Furthermore, we propose PhysXGen, a feed-forward framework for physics-grounded image-to-3D asset generation, injecting physical knowledge into the pre-trained 3D structural space. Specifically, PhysXGen employs a dual-branch architecture to explicitly model the latent correlations between 3D structures and physical properties, thereby producing 3D assets with plausible physical predictions while preserving the native geometry quality. Extensive experiments validate the superior performance and promising generalization capability of our framework. All the code, data, and models will be released to facilitate future research in generative physical AI.

We present M, an open-source, low-cost social robot platform designed to reduce platform friction that slows social robotics research by making robots easier to reproduce, modify, and deploy in real-world settings. M combines a modular mechanical design, multimodal sensing, and expressive yet mechanically simple actuation architecture with a ROS2-native software package that cleanly separates perception, expression control, and data management. The platform includes a simulation environment with interface equivalence to hardware to support rapid sim-to-real transfer of interaction behaviors. We demonstrate extensibility through additional sensing/actuation modules and provide example interaction templates for storytelling and two-way conversational coaching. Finally, we report real-world use in participatory design and week-long in-home deployments, showing how M can serve as a practical foundation for longitudinal, reproducible social robotics research.

We introduce the task of Reconstructing Objects along Hand Interaction Timelines (ROHIT). We first define the Hand Interaction Timeline (HIT) from a rigid object's perspective. In a HIT, an object is first static relative to the scene, then is held in hand following contact, where its pose changes. This is usually followed by a firm grip during use, before it is released to be static again w.r.t. to the scene. We model these pose constraints over the HIT, and propose to propagate the object's pose along the HIT enabling superior reconstruction using our proposed Constrained Optimisation and Propagation (COP) framework. Importantly, we focus on timelines with stable grasps - i.e. where the hand is stably holding an object, effectively maintaining constant contact during use. This allows us to efficiently annotate, study, and evaluate object reconstruction in videos without 3D ground truth. We evaluate our proposed task, ROHIT, over two egocentric datasets, HOT3D and in-the-wild EPIC-Kitchens. In HOT3D, we curate 1.2K clips of stable grasps. In EPIC-Kitchens, we annotate 2.4K clips of stable grasps including 390 object instances across 9 categories from videos of daily interactions in 141 environments. Without 3D ground truth, we utilise 2D projection error to assess the reconstruction. Quantitatively, COP improves stable grasp reconstruction by 6.2-11.3% and HIT reconstruction by up to 24.5% with constrained pose propagation.

Despite transformative advances in generative motion synthesis, real-time interactive motion control remains dominated by traditional techniques. In this work, we identify two key challenges in bridging research and production: 1) Real-time scalability: Industry applications demand real-time generation of a vast repertoire of motion skills, while generative methods exhibit significant degradation in quality and scalability under real-time computation constraints, and 2) Integration: Industry applications demand fine-grained multi-modal control involving velocity commands, style selection, and precise keyframes, a need largely unmet by existing text- or tag-driven models. To overcome these limitations, we introduce MotionBricks: a large-scale, real-time generative framework with a two-fold solution. First, we propose a large-scale modular latent generative backbone tailored for robust real-time motion generation, effectively modeling a dataset of over 350,000 motion clips with a single model. Second, we introduce smart primitives that provide a unified, robust, and intuitive interface for authoring both navigation and object interaction. Applications can be designed in a plug-and-play manner like assembling bricks without expert animation knowledge. Quantitatively, we show that MotionBricks produces state-of-the-art motion quality on open-source and proprietary datasets of various scales, while also achieving a real-time throughput of 15,000 FPS with 2ms latency. We demonstrate the flexibility and robustness of MotionBricks in a complete production-level animation demo, covering navigation and object-scene interaction across various styles with a unified model. To showcase our framework's application beyond animation, we deploy MotionBricks on the Unitree G1 humanoid robot to demonstrate its flexibility and generalization for real-time robotic control.

Bimanual robot systems substantially expand manipulation capabilities, but coordinating two arms introduces additional control complexity and failure modes that are not well captured by existing benchmarks. We introduce DuoBench, an extensible benchmarking framework for bimanual manipulation policies on the FR3 Duo platform. DuoBench comprises eleven tasks spanning four coordination categories, implemented in simulation and partially reproduced in the real world through reproducible task recipes with 3D-printable assets. In addition, we propose a stage-based evaluation scheme that supports fine-grained semantic failure analysis beyond binary success and provide human-teleoperated datasets for all benchmark tasks. We benchmark several dual-arm imitation-learning and vision-language-action policies in simulation and on real hardware. Our results show that current policies remain challenged by bimanual manipulation, particularly in early interaction stages, parallel arm execution, and transfer between simulation and real-world settings. DuoBench provides a reproducible testbed for diagnosing these failure modes and studying future methods for dual-arm policy learning. Code, datasets, and videos are available at https://duobench.github.io/