File size: 7,214 Bytes
547ac30 | 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 | """Research analytical surrogates for sheet LASER / PLASMA thermal cutting.
NOT a heat-transfer CFD model, real CNC controller, or empirically calibrated model.
Shared planar CNC kinematics, independently modeled electrical hardware heads.
G20 and G91 are intentionally rejected; G2/G3 circular interpolation supports I/J.
No wear, dross/HAZ/thermal distortion, overlapping-kerf, nesting/yield or real sensor data.
"""
from __future__ import annotations
import math,json,re
import numpy as np
MAT={'C45':(.00785,1.0),'304SS':(.00800,1.21),'AL6061':(.00270,.80),'S235':(.00785,.91)}
COMPONENTS={
'cnc_laser':('electronics','gantry_hold','axis_xy','z_focus','laser_standby','laser_emission_input','laser_pierce','chiller','assist_gas','exhaust_filter','servo_aux','control_aux'),
'cnc_plasma':('electronics','gantry_hold','axis_xy','torch_height','power_supply_idle','arc_cutting_input','pilot_pierce_arc','air_compressor','gas_flow','fume_extraction','cooling','control_aux')}
WORD=re.compile(r'([A-Z])\s*([+-]?(?:\d+(?:\.\d*)?|\.\d+))',re.I)
COMMENT=re.compile(r'\([^)]*\)|;[^\n]*')
def trapezoid(dist,v,a):
if dist<=1.e-12:return 0.
v=max(.05,v);a=max(1.,a)
return 2*math.sqrt(dist/a) if dist<v*v/a else 2*v/a+(dist-v*v/a)/v
def path_arc(old,xy,w,motion):
cx=old[0]+w.get('I',0.);cy=old[1]+w.get('J',0.)
r=math.hypot(old[0]-cx,old[1]-cy)
r2=math.hypot(xy[0]-cx,xy[1]-cy)
if r<1e-7 or abs(r-r2)>max(.025,r*.001):raise ValueError('Invalid G2/G3 arc geometry')
a0=math.atan2(old[1]-cy,old[0]-cx);a1=math.atan2(xy[1]-cy,xy[0]-cx)
sweep=(a1-a0)%(2*math.pi) if motion=='G3' else (a0-a1)%(2*math.pi)
if sweep<1.e-10:sweep=2*math.pi
return r*sweep
def kerf(p,feed):
t=float(p['thickness_mm']);res=MAT[p['material']][1]
if p['mode']=='cnc_laser':
kw=.095+.012*t+.023*res+.007*(float(p['laser_power_kW'])/4.)
speed_factor=(float(p['cut_feed_mm_min'])/max(feed,1.))**.075
return kw*speed_factor
kw=.55+.022*t+.13*res+.0021*float(p['current_A'])
speed_factor=(float(p['cut_feed_mm_min'])/max(feed,1.))**.055
return kw*speed_factor
def simulate(rows,teacher=False,machine_gain=None,times_override=None):
if not rows:raise ValueError('Empty program')
p=json.loads(rows[0]['initial_profile']);mode=p['mode']
if mode not in COMPONENTS:raise ValueError('laser/plasma mode only')
if teacher and machine_gain is None:raise ValueError('Private teacher gain required')
gain=float(machine_gain) if teacher else 1.
den,res=MAT[p['material']];pos=np.array([0.,0.,float(p['safe_z_mm'])]);on=False;gas=False
motion='G0';feed=float(p['cut_feed_mm_min']);absolute=True;events=[];prev_state=False
for i,row in enumerate(rows):
line=COMMENT.sub('',row['gcode'].upper()).strip()
pairs=[(a,float(b)) for a,b in WORD.findall(line)];w=dict(pairs)
gc=[int(v) for a,v in pairs if a=='G'];mc=[int(v) for a,v in pairs if a=='M']
if any(z in (20,91,93,95) for z in gc):raise ValueError('Unsupported unit/mode: use G21 G90 G94')
for g in gc:
if g in (0,1,2,3):motion='G'+str(g)
elif g==90:absolute=True
if 'F' in w:feed=w['F']
old=pos.copy();new=pos.copy()
for k,j in [('X',0),('Y',1),('Z',2)]:
if k in w:new[j]=w[k] if absolute else new[j]+w[k]
ismove=any(k in w for k in 'XYZ')
dx=float(new[0]-old[0]);dy=float(new[1]-old[1]);dz=float(new[2]-old[2])
path=math.sqrt(dx*dx+dy*dy+dz*dz) if ismove else 0.
if ismove and motion in ('G2','G3'):
path=math.hypot(path_arc(old,new,w,motion),dz)
# M3 starts cutting source; M5 stops; M8 and M9 switch gas collection state.
was_on=on
for m in mc:
if m==3:on=True
elif m==5:on=False
elif m==8:gas=True
elif m==9:gas=False
rapid='G0'==motion
v=(float(p['rapid_mm_min']) if rapid else max(1.,feed))/60.
a=float(p['accel_mm_s2'])*(1. if teacher else .88)
if ismove:t=trapezoid(path,v,a)
else:t=0.
if 4 in gc:t=max(0.,w.get('P',0.))
if 3 in mc and not was_on:t+=float(p['ignition_delay_s'])*(1. if teacher else .93)
if 8 in mc:t+=.17 if teacher else .15
if teacher and ismove and not rapid:t*=1+.009*math.tanh(path/50.)
if times_override is not None:t=float(times_override[i])
t=max(0.,t)
cutting=bool(on and ismove and motion in ('G1','G2','G3') and path>0 and abs(new[2]-float(p['cut_z_mm']))<.2)
kwidth=kerf(p,feed) if cutting else 0.
volume=path*kwidth*float(p['thickness_mm']) if cutting else 0.
# Pierce hole is material removal and separate from cut path. Pierces use G4 after M3.
piercing=bool(on and (3 in mc))
pierce_vol=math.pi/4*(1.35*kerf(p,float(p['cut_feed_mm_min'])))**2*float(p['thickness_mm']) if piercing else 0.
volume+=pierce_vol
c=np.zeros(12,dtype=np.float64)
if t>0:
def add(k,watts):c[k]+=max(0.,watts)*t/3600.
# Avoid double-counting mechanical cutting with electrical source output.
add(0,68.+8.*gain);add(1,42.+10.*gain)
if ismove:
speed=path/max(t,1e-8)
add(2,(40.+.65*speed+.007*speed**2)*gain)
if abs(dz)>1e-8:add(3,(9.+1.2*abs(dz)/max(t,1e-8))*gain)
if mode=='cnc_laser':
# Nominal kW optical / wall-plug efficiency, no arbitrary mechanical shear term.
opt=float(p['laser_power_kW'])*1000.
eff=float(p['wall_plug_efficiency'])
add(4,(230.+40.*gain)*(1 if on else .55))
if on:
add(5,opt/max(eff,.10)*(1. if cutting else .30)*gain)
if piercing:add(6,opt/max(eff,.10)*.55*gain)
add(7,(370.+.22*opt+170.*gain) if on else 220.)
if gas:add(8,(float(p['assist_gas_power_W'])+65.*gain))
add(9,240. if gas else 95.)
add(10,75.*gain);add(11,42.)
else:
arc=float(p['current_A'])*float(p['arc_voltage_V'])
eff=float(p['power_supply_efficiency'])
add(4,(110.+30.*gain)*(1. if on else .25))
if on:add(5,arc/max(eff,.1)*(1. if cutting else .24)*gain)
if piercing:add(6,arc/max(eff,.1)*.75*gain)
if gas:add(7,(float(p['compressor_power_W'])+40.*gain))
if gas:add(8,170.+.34*float(p['current_A']))
add(9,360. if gas else 90.)
add(10,190. if on else 90.)
add(11,49.)
event={'command':('G4' if 4 in gc else motion if ismove else f'M{mc[0]}' if mc else 'STATE'),
'time_s':t,'energy_Wh':float(c.sum()),'component_energy_Wh':c.tolist(),
'material_g':float(volume*den),'material_removed_mm3':volume,'kerf_mm':kwidth,
'motion_mm':path,'cutting':cutting,'piercing':piercing,'feed_mm_min':feed,
'x_after_mm':float(new[0]),'y_after_mm':float(new[1]),'z_after_mm':float(new[2]),
'source_on':bool(on),'gas_on':bool(gas)}
events.append(event);pos=new;prev_state=on
return events
|