| /*================================================================================================== | |
| * BLE CONFIGURATION | |
| * | |
| * If you are using an Arduino 101, you do not need to make any changes to this file (unless you | |
| * need a unique ble local name (see below). If you are using another supported BLE board or shield, | |
| * follow the instructions for the specific board or shield below. | |
| * | |
| * Make sure you have the Intel Curie Boards package v2.0.2 or higher installed via the Arduino | |
| * Boards Manager. | |
| * | |
| * Supported boards and shields: | |
| * - Arduino 101 (recommended) | |
| * - RedBearLab BLE Shield (v2) ** to be verified ** | |
| * - RedBearLab BLE Nano ** works with modifications ** | |
| * - Adafruit Feather M0 Bluefruit LE | |
| * | |
| *================================================================================================*/ | |
| // change this to a unique name per board if running StandardFirmataBLE on multiple boards | |
| // within the same physical space | |
| /* | |
| * Arduino 101 | |
| * | |
| * Make sure you have the Intel Curie Boards package v2.0.2 or higher installed via the Arduino | |
| * Boards Manager. | |
| * | |
| * Test script: https://gist.github.com/soundanalogous/927360b797574ed50e27 | |
| */ | |
| // After conversion to units of 1.25ms, both values must be between | |
| // 0x0006 (7.5ms) and 0x0c80 (4s) | |
| /* | |
| * RedBearLab BLE Shield | |
| * | |
| * If you are using a RedBearLab BLE shield, uncomment the define below. | |
| * Also, change the define for BLE_RST if you have the jumper set to pin 7 rather than pin 4. | |
| * | |
| * You will need to use the shield with an Arduino Zero, Due, Mega, or other board with sufficient | |
| * Flash and RAM. Arduino Uno, Leonardo and other ATmega328p and Atmega32u4 boards to not have | |
| * enough memory to run StandardFirmataBLE. | |
| * | |
| * TODO: verify if this works and with which boards it works. | |
| * | |
| * Test script: https://gist.github.com/soundanalogous/927360b797574ed50e27 | |
| */ | |
| //#define REDBEAR_BLE_SHIELD | |
| /* | |
| * Adafruit Feather M0 Bluefruit LE | |
| * | |
| * If you are using an Adafruit Feather M0 Bluefruit LE, uncomment the define below. | |
| * This configuration should also work with other Bluefruit LE boards/modules that communicate | |
| * with the nRF51822 via SPI (e.g. Bluefruit LE SPI Friend, Bluefruit LE Shield), although | |
| * you may need to change the values of BLE_SPI_CS, BLE_SPI_IRQ, and/or BLE_SPI_RST below. | |
| * | |
| * You will need to install a lightly-modified version of the Adafruit BluefruitLE nRF51 | |
| * package, available at: | |
| * https://github.com/cstawarz/Adafruit_BluefruitLE_nRF51/archive/firmata_fixes.zip | |
| */ | |
| //#define BLUEFRUIT_LE_SPI | |
| // Both values must be between 10ms and 4s | |
| /* | |
| * Generic settings | |
| */ | |
| // These values apply to all devices using the Arduino BLEPeripheral library | |
| // with a Nordic nRF8001 or nRF51822. Both values must be between | |
| // 0x0006 (7.5ms) and 0x0c80 (4s). | |
| /*================================================================================================== | |
| * END BLE CONFIGURATION - you should not need to change anything below this line | |
| *================================================================================================*/ | |
| BLEStream stream; | |
| BLEStream stream(BLE_REQ, BLE_RDY, BLE_RST); | |
| BluefruitLE_SPI_Stream stream(BLE_SPI_CS, BLE_SPI_IRQ, BLE_SPI_RST); | |
| /* | |
| * RedBearLab BLE Nano (with default switch settings) | |
| * | |
| * Blocked on this issue: https://github.com/RedBearLab/nRF51822-Arduino/issues/46 | |
| * Works with modifications. See comments at top of the test script referenced below. | |
| * When the RBL nRF51822-Arduino library issue is resolved, this should work witout | |
| * any modifications. | |
| * | |
| * Test script: https://gist.github.com/soundanalogous/d39bb3eb36333a0906df | |
| * | |
| * Note: If you have changed the solder jumpers on the Nano you may encounter issues since | |
| * the pins are currently mapped in Firmata only for the default (factory) jumper settings. | |
| */ | |
| // #ifdef BLE_NANO | |
| // #include "utility/BLEStream.h" | |
| // BLEStream stream; | |
| // #endif | |
| /* | |
| * RedBearLab Blend and Blend Micro | |
| * | |
| * StandardFirmataBLE requires too much Flash and RAM to run on the ATmega32u4-based Blend | |
| * and Blend Micro boards. It may work with ConfigurableFirmata selecting only analog and/or | |
| * digital I/O. | |
| */ | |
| // #if defined(BLEND_MICRO) || defined(BLEND) | |
| // #include <SPI.h> | |
| // #include "utility/BLEStream.h" | |
| // #define BLE_REQ 6 | |
| // #define BLE_RDY 7 | |
| // #define BLE_RST 4 | |
| // BLEStream stream(BLE_REQ, BLE_RDY, BLE_RST); | |
| // #endif | |