Dataset Viewer
Auto-converted to Parquet Duplicate
fix_id
int64
849
56.7k
code_id
int64
213
15.4k
fix_title
large_stringlengths
21
90
probability_rank
int64
1
7
difficulty_level
large_stringclasses
3 values
est_parts_cost_min_usd
float64
0
1.2k
est_parts_cost_max_usd
float64
0
3.2k
est_labor_hours
float64
0.2
4.5
⌀
step_by_step_instructions
large_stringlengths
78
644
action_type
stringclasses
4 values
parts_cost_status
large_stringclasses
2 values
labor_status
large_stringclasses
2 values
cost_basis_id
large_stringclasses
1 value
procedure_rationale
stringclasses
7 values
__index_level_0__
int64
848
56.7k
849
213
Inspect wheel speed sensor connector and harness routing
1
Easy DIY
5
25
0.4
Locate the sensor connector near the hub or knuckle at the affected corner • Unplug and inspect for corrosion, moisture, or a bent pin • Follow the harness up to the body grommet checking for chafing against the strut or subframe • Clean, reseat, clear the code, and road test
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
848
850
213
Test wheel speed sensor resistance and signal
2
Moderate DIY
10
40
0.6
Unplug the sensor and measure coil resistance against the factory specification • Reconnect and back-probe the signal circuit while rotating the wheel by hand • Confirm a clean, consistent AC signal with no dropouts • Replace the sensor if resistance is out of range or the signal is erratic
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
849
851
213
Replace wheel speed sensor
3
Moderate DIY
30
120
0.6
Disconnect the battery negative terminal • Remove the sensor mounting bolt and pull the sensor from the knuckle • Install the replacement sensor, confirming it seats fully against the tone ring • Clear the code and confirm signal quality across a range of speeds
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
850
852
213
Repair chafed wheel speed sensor harness wiring
4
Professional Required
15
65
1.2
Trace the harness from the sensor to the body connector along the strut and control arm • Identify the chafe point, commonly where the harness crosses suspension travel • Repair damaged conductors with solder and heat-shrink, then re-route and secure the harness • Clear codes and confirm all four corners correlate corr...
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
851
865
217
Inspect wheel speed sensor connector and harness routing
1
Easy DIY
5
25
0.4
Locate the sensor connector near the hub or knuckle at the affected corner • Unplug and inspect for corrosion, moisture, or a bent pin • Follow the harness up to the body grommet checking for chafing against the strut or subframe • Clean, reseat, clear the code, and road test
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
864
866
217
Test wheel speed sensor resistance and signal
2
Moderate DIY
10
40
0.6
Unplug the sensor and measure coil resistance against the factory specification • Reconnect and back-probe the signal circuit while rotating the wheel by hand • Confirm a clean, consistent AC signal with no dropouts • Replace the sensor if resistance is out of range or the signal is erratic
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
865
867
217
Replace wheel speed sensor
3
Moderate DIY
30
120
0.6
Disconnect the battery negative terminal • Remove the sensor mounting bolt and pull the sensor from the knuckle • Install the replacement sensor, confirming it seats fully against the tone ring • Clear the code and confirm signal quality across a range of speeds
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
866
868
217
Repair chafed wheel speed sensor harness wiring
4
Professional Required
15
65
1.2
Trace the harness from the sensor to the body connector along the strut and control arm • Identify the chafe point, commonly where the harness crosses suspension travel • Repair damaged conductors with solder and heat-shrink, then re-route and secure the harness • Clear codes and confirm all four corners correlate corr...
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
867
909
228
Adjust brake pedal switch plunger clearance
1
Easy DIY
3
15
0.3
Locate the brake pedal switch mounted on the pedal bracket above the pedal arm • Loosen the switch locknut and adjust plunger contact per the service manual clearance spec • Pull the pedal fully rearward to auto-adjust the switch on platforms that support it • Verify stop lamps and scan tool brake switch PID respond co...
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
908
910
228
Inspect brake pedal switch connector
2
Easy DIY
5
20
0.3
Unplug the switch connector and inspect pins for corrosion • Clean with electrical contact cleaner and reseat the connector • Confirm both switch channels toggle together with a multimeter • Clear the code and verify stop lamp operation
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
909
911
228
Replace brake pedal switch
3
Moderate DIY
15
60
0.5
Disconnect the battery negative terminal • Rotate and remove the switch from the pedal bracket • Install the replacement switch and adjust plunger clearance to spec • Clear codes and confirm correct stop lamp and brake-applied signal operation
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
910
912
228
Repair stop lamp/brake switch circuit wiring
4
Professional Required
15
60
1
Trace the harness from the switch to the module and stop lamp fuse • Check for chafing near the pedal bracket and steering column • Repair with solder and heat-shrink where damaged • Verify both switch channels and stop lamps function correctly
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
911
2,710
684
Change engine oil and filter to spec viscosity
1
Easy DIY
25
60
0.5
1. Drain and inspect oil condition for sludge or debris • 2. Replace with OEM-viscosity oil and a new filter • 3. Clear codes and run a phaser sweep test with a scan tool • 4. Road test through varied load to confirm stable timing
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
2,709
2,711
684
Replace oil control valve and clean phaser feed passage
2
Moderate DIY
35
160
1.3
1. Remove the OCV solenoid and inspect its filter screen • 2. Clean the oil feed passage to the phaser of sludge with solvent and compressed air • 3. Install a new OCV solenoid • 4. Clear adaptive learning and verify timing response
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
2,710
2,712
684
Replace worn camshaft phaser assembly
3
Professional Required
180
550
2.8
1. Set the engine to TDC and lock the timing chain • 2. Remove the worn phaser and inspect the chain/tensioner for related wear • 3. Install the new phaser and retime to factory marks • 4. Verify actuator sweep and clear codes
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
2,711
2,713
684
Correct timing chain/belt installation
4
Professional Required
150
900
3.5
1. Remove the timing cover and verify marks against factory specification • 2. Correct any tooth-count misalignment on the chain or belt • 3. Replace the tensioner and guides while accessed • 4. Confirm cam/crank correlation and phaser response
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
2,712
2,729
689
Inspect and replace crankshaft/camshaft position sensor
1
Moderate DIY
25
90
0.8
1. Identify which sensor the correlation fault points to on the scan tool freeze frame • 2. Unplug and remove the affected position sensor • 3. Inspect the reluctor wheel/tone ring for chips or debris • 4. Install the new sensor with correct air-gap shim and clear codes
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
2,728
2,730
689
Inspect timing chain/belt for stretch or jumped timing
2
Professional Required
150
900
3.5
1. Remove the timing cover and verify cam-to-crank alignment against factory timing marks • 2. Measure chain stretch or check belt tooth wear • 3. Replace the timing chain/belt, tensioner, and guides as a set • 4. Reset timing to factory marks and verify correlation with a scan tool
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
2,729
2,731
689
Repair crank/cam sensor wiring and connectors
3
Professional Required
10
60
1.2
1. Back-probe the sensor signal and ground at each connector while cranking • 2. Voltage-drop test the harness runs back to the ECM • 3. Repair chafed conductors near the timing cover with heat-shrink splices • 4. Confirm clean square-wave signals on a scope
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
2,730
3,481
924
Clean MAF sensing element
2
Easy DIY
8
20
null
1. Remove the intake duct clamp and unplug the MAF connector • 2. Remove the sensor with a security Torx bit • 3. Spray the hot-wire element with dedicated MAF cleaner (never touch it) • 4. Reinstall, clear the code, and road test
repair
estimated
unknown
obd-editorial-us-aftermarket-v1
Cleaning restores the existing sensor before anything is bought; the cleaner cost is carried from the original step. The original time covered cleaning and the duct check together, so it is not carried.
3,480
3,482
924
Replace mass air flow sensor
7
Moderate DIY
45
220
0.5
1. Disconnect the battery negative terminal • 2. Unplug the MAF harness connector and remove the sensor screws • 3. Install the replacement sensor without touching the element • 4. Reconnect and perform an ECU idle relearn if the platform requires it
replace
estimated
estimated
obd-editorial-us-aftermarket-v1
The costliest step comes last, after the checks above; its estimates are carried unchanged.
3,481
3,483
924
Replace cracked intake boots and couplers downstream of the MAF
4
Moderate DIY
10
60
null
1. Replace cracked intake boots and hardened couplers • 2. Torque all clamps and verify fuel trims return toward 0% at idle
replace
estimated
unknown
obd-editorial-us-aftermarket-v1
Done only when the smoke test finds a cracked boot or coupler, so it sits right after that test; the boot and coupler cost is carried from the original step, whose time covered testing and replacement together and is not carried.
3,482
3,484
924
Repair MAF circuit wiring
6
Professional Required
5
40
null
1. Repair chafed or corroded conductors found in the circuit test with solder and heat-shrink • 2. Confirm live airflow (g/s) tracks RPM on a scan tool
repair
estimated
unknown
obd-editorial-us-aftermarket-v1
Done only when the circuit test finds a fault; the repair-kit cost is carried from the original step, whose time covered testing and repair together and is not carried.
3,483
3,485
925
Clean MAF sensing element
2
Easy DIY
8
20
null
1. Remove the intake duct clamp and unplug the MAF connector • 2. Remove the sensor with a security Torx bit • 3. Spray the hot-wire element with dedicated MAF cleaner (never touch it) • 4. Reinstall, clear the code, and road test
repair
estimated
unknown
obd-editorial-us-aftermarket-v1
Cleaning restores the existing sensor before anything is bought; the cleaner cost is carried from the original step. The original time covered cleaning and the duct check together, so it is not carried.
3,484
3,486
925
Replace mass air flow sensor
7
Moderate DIY
45
220
0.5
1. Disconnect the battery negative terminal • 2. Unplug the MAF harness connector and remove the sensor screws • 3. Install the replacement sensor without touching the element • 4. Reconnect and perform an ECU idle relearn if the platform requires it
replace
estimated
estimated
obd-editorial-us-aftermarket-v1
The costliest step comes last, after the checks above; its estimates are carried unchanged.
3,485
3,487
925
Replace cracked intake boots and couplers downstream of the MAF
4
Moderate DIY
10
60
null
1. Replace cracked intake boots and hardened couplers • 2. Torque all clamps and verify fuel trims return toward 0% at idle
replace
estimated
unknown
obd-editorial-us-aftermarket-v1
Done only when the smoke test finds a cracked boot or coupler, so it sits right after that test; the boot and coupler cost is carried from the original step, whose time covered testing and replacement together and is not carried.
3,486
3,488
925
Repair MAF circuit wiring
6
Professional Required
5
40
null
1. Repair chafed or corroded conductors found in the circuit test with solder and heat-shrink • 2. Confirm live airflow (g/s) tracks RPM on a scan tool
repair
estimated
unknown
obd-editorial-us-aftermarket-v1
Done only when the circuit test finds a fault; the repair-kit cost is carried from the original step, whose time covered testing and repair together and is not carried.
3,487
3,500
929
Inspect and clean MAP sensor vacuum port
1
Easy DIY
5
20
0.5
1. Locate the MAP sensor on the intake manifold • 2. Remove and inspect the vacuum port for oil or debris • 3. Clean the port and sensor housing • 4. Reinstall and clear codes
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,499
3,501
929
Replace MAP/barometric pressure sensor
2
Easy DIY
20
90
0.4
1. Unplug the sensor connector • 2. Remove the sensor from the manifold or its remote mount • 3. Install the replacement sensor with a new O-ring • 4. Clear codes and verify reading against known altitude/barometric baseline
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,500
3,502
929
Repair MAP sensor circuit wiring
3
Professional Required
10
60
1.2
1. Back-probe the 5V reference, signal, and ground at the connector • 2. Voltage-drop test each leg back to the ECM • 3. Repair chafed or corroded conductors with heat-shrink splices • 4. Confirm signal tracks vacuum/boost changes smoothly
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,501
3,545
942
Inspect and clean IAT sensor connector
1
Easy DIY
5
15
0.4
1. Locate the IAT sensor in the intake tube or integrated into the MAF housing • 2. Unplug and inspect for corrosion or debris • 3. Clean contacts and apply dielectric grease • 4. Reconnect and clear codes
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,544
3,546
942
Replace intake air temperature sensor
2
Easy DIY
10
50
0.4
1. Locate the affected IAT sensor per the bank/position in the code • 2. Disconnect and remove the sensor from its bore • 3. Install the replacement sensor with a new seal • 4. Clear codes and verify reading tracks ambient at cold start
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,545
3,547
942
Repair IAT sensor circuit wiring
3
Professional Required
10
55
1.1
1. Measure sensor resistance at the connector against a temperature/resistance chart • 2. Voltage-drop test the circuit back to the ECM • 3. Repair chafed or corroded wiring near the intake tract with heat-shrink splices • 4. Confirm stable readings across temperature swings
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,546
3,548
943
Inspect and clean IAT sensor connector
1
Easy DIY
5
15
0.4
1. Locate the IAT sensor in the intake tube or integrated into the MAF housing • 2. Unplug and inspect for corrosion or debris • 3. Clean contacts and apply dielectric grease • 4. Reconnect and clear codes
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,547
3,549
943
Replace intake air temperature sensor
2
Easy DIY
10
50
0.4
1. Locate the affected IAT sensor per the bank/position in the code • 2. Disconnect and remove the sensor from its bore • 3. Install the replacement sensor with a new seal • 4. Clear codes and verify reading tracks ambient at cold start
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,548
3,550
943
Repair IAT sensor circuit wiring
3
Professional Required
10
55
1.1
1. Measure sensor resistance at the connector against a temperature/resistance chart • 2. Voltage-drop test the circuit back to the ECM • 3. Repair chafed or corroded wiring near the intake tract with heat-shrink splices • 4. Confirm stable readings across temperature swings
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,549
3,560
947
Top off coolant and inspect ECT sensor connector
1
Easy DIY
10
30
0.4
1. Check coolant level and top off with the correct spec coolant • 2. Unplug the ECT sensor connector and inspect for corrosion • 3. Clean contacts and reconnect • 4. Clear codes and monitor warm-up temperature curve
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,559
3,561
947
Replace engine/radiator coolant temperature sensor
2
Moderate DIY
15
70
0.6
1. Relieve cooling system pressure and drain coolant to below sensor level • 2. Remove the sensor from the head, housing, or radiator tank • 3. Install the replacement sensor with sealant or new seal as specified • 4. Refill coolant, bleed air, and clear codes
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,560
3,562
947
Repair coolant temperature sensor wiring
3
Professional Required
10
60
1.2
1. Measure sensor resistance at the connector against a temperature/resistance chart • 2. Voltage-drop test the circuit back to the ECM • 3. Repair chafed or corroded wiring with heat-shrink splices • 4. Confirm reading tracks actual coolant temperature
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,561
3,587
956
Inspect and clean throttle/pedal position sensor connector
1
Easy DIY
5
20
0.4
1. Locate the throttle body or accelerator pedal assembly connector • 2. Unplug and inspect for corrosion or bent pins • 3. Clean contacts and reseat firmly • 4. Clear codes and verify smooth voltage sweep
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,586
3,588
956
Replace throttle body or pedal position sensor assembly
2
Moderate DIY
60
280
0.8
1. Unplug the connector and remove the mounting fasteners • 2. Install the replacement throttle body or pedal assembly • 3. Reconnect and perform a throttle relearn if required • 4. Clear codes and verify all channels track together
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,587
3,589
956
Repair throttle/pedal position sensor wiring
3
Professional Required
10
60
1.3
1. Back-probe the reference, signal, and ground circuits at the connector • 2. Voltage-drop test each leg back to the ECM • 3. Repair chafed conductors with heat-shrink splices • 4. Confirm all sensor channels agree throughout the pedal/throttle sweep
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,588
3,608
963
Check coolant level and inspect for external leaks
1
Easy DIY
10
40
0.5
1. Check coolant level cold and top off to spec • 2. Inspect hoses, radiator, and water pump weep hole for leaks • 3. Repair any obvious external leak source • 4. Clear codes and monitor warm-up time
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,607
3,609
963
Replace stuck-open thermostat
2
Moderate DIY
20
90
1
1. Drain coolant below the thermostat housing • 2. Remove the housing and replace the thermostat and gasket • 3. Refill coolant and bleed air from the system • 4. Confirm engine reaches operating temperature within expected time
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,608
3,610
963
Replace failing water pump
3
Professional Required
120
450
2
1. Drain coolant and remove drive components to access the water pump • 2. Remove the worn pump and inspect the impeller and bearing • 3. Install the replacement pump with a new gasket • 4. Refill, bleed, and verify stable circulation and temperature
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,609
3,635
972
Inspect for exhaust leaks near the O2 sensor
1
Easy DIY
5
40
0.6
1. Inspect the exhaust manifold and pipe joints near the sensor bung for leaks • 2. Listen and smoke-test for exhaust leaks upstream of the sensor • 3. Replace gaskets or tighten fasteners as needed • 4. Clear codes and monitor sensor voltage trace
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,634
3,636
972
Replace oxygen sensor
2
Moderate DIY
50
180
0.6
1. Identify the affected bank/sensor position • 2. Remove the sensor with an O2 sensor socket • 3. Apply anti-seize to threads (avoid the tip) and install the new sensor • 4. Clear codes and confirm a normal switching voltage trace
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,635
3,637
972
Repair O2 sensor signal circuit wiring
3
Professional Required
10
60
1.2
1. Back-probe the signal and ground at the connector with the engine running • 2. Voltage-drop test the circuit back to the ECM • 3. Repair chafed or corroded wiring near the exhaust with high-temp splices • 4. Confirm proper switching activity
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,636
3,641
974
Inspect for contamination sources (oil, coolant, silicone) reaching the exhaust
1
Easy DIY
5
60
0.8
1. Check for oil consumption, coolant leaks, or recent use of silicone sealant near the intake/exhaust • 2. Repair the contamination source if found • 3. Inspect the sensor tip for a sooty or white/gray glassy coating • 4. Clear codes after addressing the source
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,640
3,642
974
Replace slow-responding oxygen sensor
2
Moderate DIY
50
180
0.6
1. Identify the affected bank/sensor position • 2. Remove with an O2 sensor socket and inspect the old sensor tip for contamination • 3. Apply anti-seize and install the new sensor • 4. Clear codes and verify switching frequency improves
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,641
3,643
974
Repair exhaust leak diluting sensor sample
3
Moderate DIY
20
120
1.2
1. Smoke-test the exhaust system upstream of the affected sensor • 2. Replace leaking gaskets or cracked pipe sections • 3. Torque fasteners to spec • 4. Clear codes and re-verify switching speed
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,642
3,647
976
Test O2 sensor heater circuit fuse and relay
1
Easy DIY
5
25
0.4
1. Locate the O2 heater fuse and relay in the underhood fuse box • 2. Inspect and test with a multimeter for continuity and proper switching • 3. Replace any blown fuse or failed relay • 4. Clear codes and verify heater current draw
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,646
3,648
976
Replace oxygen sensor with failed heater
2
Moderate DIY
50
180
0.6
1. Identify the affected bank/sensor position from the code • 2. Unplug the connector and remove the sensor with an O2 sensor socket • 3. Apply anti-seize to threads (avoid the sensor tip) and install the new sensor • 4. Reconnect and clear codes
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,647
3,649
976
Repair O2 heater circuit wiring
3
Professional Required
10
60
1.2
1. Measure heater element resistance at the connector against spec • 2. Voltage-drop test the heater supply and ground legs • 3. Repair chafed or corroded wiring near the exhaust manifold with high-temp splices • 4. Confirm heater current draw matches spec
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,648
3,656
979
Inspect for exhaust leaks near the O2 sensor
1
Easy DIY
5
40
0.6
1. Inspect the exhaust manifold and pipe joints near the sensor bung for leaks • 2. Listen and smoke-test for exhaust leaks upstream of the sensor • 3. Replace gaskets or tighten fasteners as needed • 4. Clear codes and monitor sensor voltage trace
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,655
3,657
979
Replace oxygen sensor
2
Moderate DIY
50
180
0.6
1. Identify the affected bank/sensor position • 2. Remove the sensor with an O2 sensor socket • 3. Apply anti-seize to threads (avoid the tip) and install the new sensor • 4. Clear codes and confirm a normal switching voltage trace
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,656
3,658
979
Repair O2 sensor signal circuit wiring
3
Professional Required
10
60
1.2
1. Back-probe the signal and ground at the connector with the engine running • 2. Voltage-drop test the circuit back to the ECM • 3. Repair chafed or corroded wiring near the exhaust with high-temp splices • 4. Confirm proper switching activity
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,657
3,683
988
Test O2 sensor heater circuit fuse and relay
1
Easy DIY
5
25
0.4
1. Locate the O2 heater fuse and relay in the underhood fuse box • 2. Inspect and test with a multimeter for continuity and proper switching • 3. Replace any blown fuse or failed relay • 4. Clear codes and verify heater current draw
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,682
3,684
988
Replace oxygen sensor with failed heater
2
Moderate DIY
50
180
0.6
1. Identify the affected bank/sensor position from the code • 2. Unplug the connector and remove the sensor with an O2 sensor socket • 3. Apply anti-seize to threads (avoid the sensor tip) and install the new sensor • 4. Reconnect and clear codes
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,683
3,685
988
Repair O2 heater circuit wiring
3
Professional Required
10
60
1.2
1. Measure heater element resistance at the connector against spec • 2. Voltage-drop test the heater supply and ground legs • 3. Repair chafed or corroded wiring near the exhaust manifold with high-temp splices • 4. Confirm heater current draw matches spec
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,684
3,827
1,036
Smoke-test intake for vacuum/air leaks
1
Easy DIY
10
40
0.8
1. Connect a smoke machine to the intake at idle • 2. Watch for smoke escaping at intake gaskets, PCV hoses, or brake booster line • 3. Replace any leaking gasket or hose • 4. Clear codes and verify fuel trims return toward 0%
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,826
3,828
1,036
Replace fuel filter and test fuel pump output
2
Moderate DIY
30
150
1
1. Replace the fuel filter if serviceable • 2. Measure fuel pump pressure and volume against spec under load • 3. Replace a weak pump if it fails the test • 4. Clear codes and confirm rail pressure holds steady
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,827
3,829
1,036
Inspect and repair exhaust manifold gasket leak
3
Moderate DIY
40
180
1.5
1. Inspect the exhaust manifold gasket and studs near the upstream O2 sensor for leaks • 2. Replace the gasket and any corroded studs • 3. Torque to spec in sequence • 4. Clear codes and re-verify trim correction
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,828
3,830
1,037
Clean MAF sensor and inspect for false-high airflow readings
1
Easy DIY
8
25
0.4
1. Remove the MAF sensor and inspect the hot-wire element for contamination • 2. Clean with dedicated MAF cleaner (never touch the element) • 3. Reinstall and clear codes • 4. Compare live MAF g/s reading against expected values
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,829
3,831
1,037
Test fuel injectors for leakage and replace as needed
2
Moderate DIY
40
220
1.5
1. Perform a fuel injector leak-down/drip test • 2. Identify any injector leaking past its seat • 3. Replace the faulty injector(s) and seals • 4. Clear codes and verify trims return toward 0%
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,830
3,832
1,037
Replace stuck-open fuel pressure regulator
3
Moderate DIY
40
180
1
1. Depressurize the fuel system • 2. Remove the regulator and inspect the diaphragm/valve for sticking • 3. Install the replacement regulator with new seals • 4. Clear codes and confirm rail pressure holds at commanded target
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,831
3,836
1,039
Smoke-test intake for vacuum/air leaks
1
Easy DIY
10
40
0.8
1. Connect a smoke machine to the intake at idle • 2. Watch for smoke escaping at intake gaskets, PCV hoses, or brake booster line • 3. Replace any leaking gasket or hose • 4. Clear codes and verify fuel trims return toward 0%
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,835
3,837
1,039
Replace fuel filter and test fuel pump output
2
Moderate DIY
30
150
1
1. Replace the fuel filter if serviceable • 2. Measure fuel pump pressure and volume against spec under load • 3. Replace a weak pump if it fails the test • 4. Clear codes and confirm rail pressure holds steady
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,836
3,838
1,039
Inspect and repair exhaust manifold gasket leak
3
Moderate DIY
40
180
1.5
1. Inspect the exhaust manifold gasket and studs near the upstream O2 sensor for leaks • 2. Replace the gasket and any corroded studs • 3. Torque to spec in sequence • 4. Clear codes and re-verify trim correction
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,837
3,839
1,040
Clean MAF sensor and inspect for false-high airflow readings
1
Easy DIY
8
25
0.4
1. Remove the MAF sensor and inspect the hot-wire element for contamination • 2. Clean with dedicated MAF cleaner (never touch the element) • 3. Reinstall and clear codes • 4. Compare live MAF g/s reading against expected values
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,838
3,840
1,040
Test fuel injectors for leakage and replace as needed
2
Moderate DIY
40
220
1.5
1. Perform a fuel injector leak-down/drip test • 2. Identify any injector leaking past its seat • 3. Replace the faulty injector(s) and seals • 4. Clear codes and verify trims return toward 0%
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,839
3,841
1,040
Replace stuck-open fuel pressure regulator
3
Moderate DIY
40
180
1
1. Depressurize the fuel system • 2. Remove the regulator and inspect the diaphragm/valve for sticking • 3. Install the replacement regulator with new seals • 4. Clear codes and confirm rail pressure holds at commanded target
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
3,840
5,039
1,435
Replace spark plugs and inspect ignition coils as a set
1
Easy DIY
30
90
1.2
1. Retrieve freeze-frame data to see which cylinders were flagged • 2. Remove and inspect all spark plugs for wear, fouling, or incorrect gap • 3. Replace the full set with OE-spec plugs • 4. Swap coils between cylinders if a weak coil is suspected • 5. Clear codes and monitor misfire counters on a drive cycle
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,038
5,040
1,435
Smoke-test intake and vacuum lines for a shared leak
2
Moderate DIY
15
60
1
1. Connect a smoke machine at the intake tract with all accessory vacuum ports capped • 2. Watch for smoke escaping at intake gaskets, PCV hoses, or brake booster lines • 3. Replace any cracked hose or gasket found • 4. Clear the code and verify fuel trims return to normal
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,039
5,041
1,435
Verify fuel delivery and refuel if the tank is low
3
Easy DIY
5
20
0.2
1. Check the fuel gauge and refuel above one-quarter tank if low • 2. Scan for low fuel pressure or pump duty-cycle codes stored alongside the misfire • 3. Clear the code and complete a drive cycle to confirm it does not return
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,040
5,042
1,435
Test fuel pump output pressure and delivery volume
4
Moderate DIY
20
250
1.3
1. Connect a fuel pressure gauge to the test port or rail • 2. Compare static and key-on pressure to spec • 3. Perform a timed volume test at the return line if accessible • 4. Replace a fuel pump that cannot hold pressure or deliver volume under load
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,041
5,043
1,436
Swap spark plug and ignition coil to confirm the cylinder
1
Easy DIY
15
45
0.6
1. Remove the coil and plug from the misfiring cylinder • 2. Inspect the plug for fouling, wear, or an incorrect gap • 3. Swap the coil with a known-good adjacent cylinder's coil • 4. Clear the code and see if the misfire follows the coil or stays with the cylinder • 5. Replace the plug and/or coil based on the result
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,042
5,044
1,436
Test and clean or replace the cylinder's fuel injector
2
Moderate DIY
40
180
1
1. Perform an injector balance or ohms test on the affected cylinder • 2. Swap the injector with a neighboring cylinder to see if the misfire follows • 3. Clean the injector on an ultrasonic bench or replace it • 4. Reinstall with new O-rings and clear codes
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,043
5,045
1,436
Run a cylinder compression or leak-down test
3
Moderate DIY
20
80
1.5
1. Disable fuel and ignition for a dry compression test on all cylinders • 2. Compare the flagged cylinder's reading against its neighbors • 3. Add oil and retest (wet test) to isolate rings vs. valves • 4. Follow up with a leak-down test to confirm the exact leak path
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,044
5,046
1,436
Inspect and replace a leaking or damaged cylinder head gasket/valve
4
Professional Required
150
900
4.5
1. Confirm the leak-down result points to a head gasket or valve seat • 2. Remove the valve cover/head as required for access • 3. Replace the head gasket or recondition the valve seat • 4. Reassemble to torque spec and verify compression returns to spec
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,045
5,047
1,437
Swap spark plug and ignition coil to confirm the cylinder
1
Easy DIY
15
45
0.6
1. Remove the coil and plug from the misfiring cylinder • 2. Inspect the plug for fouling, wear, or an incorrect gap • 3. Swap the coil with a known-good adjacent cylinder's coil • 4. Clear the code and see if the misfire follows the coil or stays with the cylinder • 5. Replace the plug and/or coil based on the result
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,046
5,048
1,437
Test and clean or replace the cylinder's fuel injector
2
Moderate DIY
40
180
1
1. Perform an injector balance or ohms test on the affected cylinder • 2. Swap the injector with a neighboring cylinder to see if the misfire follows • 3. Clean the injector on an ultrasonic bench or replace it • 4. Reinstall with new O-rings and clear codes
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,047
5,049
1,437
Run a cylinder compression or leak-down test
3
Moderate DIY
20
80
1.5
1. Disable fuel and ignition for a dry compression test on all cylinders • 2. Compare the flagged cylinder's reading against its neighbors • 3. Add oil and retest (wet test) to isolate rings vs. valves • 4. Follow up with a leak-down test to confirm the exact leak path
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,048
5,050
1,437
Inspect and replace a leaking or damaged cylinder head gasket/valve
4
Professional Required
150
900
4.5
1. Confirm the leak-down result points to a head gasket or valve seat • 2. Remove the valve cover/head as required for access • 3. Replace the head gasket or recondition the valve seat • 4. Reassemble to torque spec and verify compression returns to spec
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,049
5,051
1,438
Swap spark plug and ignition coil to confirm the cylinder
1
Easy DIY
15
45
0.6
1. Remove the coil and plug from the misfiring cylinder • 2. Inspect the plug for fouling, wear, or an incorrect gap • 3. Swap the coil with a known-good adjacent cylinder's coil • 4. Clear the code and see if the misfire follows the coil or stays with the cylinder • 5. Replace the plug and/or coil based on the result
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,050
5,052
1,438
Test and clean or replace the cylinder's fuel injector
2
Moderate DIY
40
180
1
1. Perform an injector balance or ohms test on the affected cylinder • 2. Swap the injector with a neighboring cylinder to see if the misfire follows • 3. Clean the injector on an ultrasonic bench or replace it • 4. Reinstall with new O-rings and clear codes
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,051
5,053
1,438
Run a cylinder compression or leak-down test
3
Moderate DIY
20
80
1.5
1. Disable fuel and ignition for a dry compression test on all cylinders • 2. Compare the flagged cylinder's reading against its neighbors • 3. Add oil and retest (wet test) to isolate rings vs. valves • 4. Follow up with a leak-down test to confirm the exact leak path
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,052
5,054
1,438
Inspect and replace a leaking or damaged cylinder head gasket/valve
4
Professional Required
150
900
4.5
1. Confirm the leak-down result points to a head gasket or valve seat • 2. Remove the valve cover/head as required for access • 3. Replace the head gasket or recondition the valve seat • 4. Reassemble to torque spec and verify compression returns to spec
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,053
5,055
1,439
Swap spark plug and ignition coil to confirm the cylinder
1
Easy DIY
15
45
0.6
1. Remove the coil and plug from the misfiring cylinder • 2. Inspect the plug for fouling, wear, or an incorrect gap • 3. Swap the coil with a known-good adjacent cylinder's coil • 4. Clear the code and see if the misfire follows the coil or stays with the cylinder • 5. Replace the plug and/or coil based on the result
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,054
5,056
1,439
Test and clean or replace the cylinder's fuel injector
2
Moderate DIY
40
180
1
1. Perform an injector balance or ohms test on the affected cylinder • 2. Swap the injector with a neighboring cylinder to see if the misfire follows • 3. Clean the injector on an ultrasonic bench or replace it • 4. Reinstall with new O-rings and clear codes
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,055
5,057
1,439
Run a cylinder compression or leak-down test
3
Moderate DIY
20
80
1.5
1. Disable fuel and ignition for a dry compression test on all cylinders • 2. Compare the flagged cylinder's reading against its neighbors • 3. Add oil and retest (wet test) to isolate rings vs. valves • 4. Follow up with a leak-down test to confirm the exact leak path
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,056
5,058
1,439
Inspect and replace a leaking or damaged cylinder head gasket/valve
4
Professional Required
150
900
4.5
1. Confirm the leak-down result points to a head gasket or valve seat • 2. Remove the valve cover/head as required for access • 3. Replace the head gasket or recondition the valve seat • 4. Reassemble to torque spec and verify compression returns to spec
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,057
5,059
1,440
Swap spark plug and ignition coil to confirm the cylinder
1
Easy DIY
15
45
0.6
1. Remove the coil and plug from the misfiring cylinder • 2. Inspect the plug for fouling, wear, or an incorrect gap • 3. Swap the coil with a known-good adjacent cylinder's coil • 4. Clear the code and see if the misfire follows the coil or stays with the cylinder • 5. Replace the plug and/or coil based on the result
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,058
5,060
1,440
Test and clean or replace the cylinder's fuel injector
2
Moderate DIY
40
180
1
1. Perform an injector balance or ohms test on the affected cylinder • 2. Swap the injector with a neighboring cylinder to see if the misfire follows • 3. Clean the injector on an ultrasonic bench or replace it • 4. Reinstall with new O-rings and clear codes
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,059
5,061
1,440
Run a cylinder compression or leak-down test
3
Moderate DIY
20
80
1.5
1. Disable fuel and ignition for a dry compression test on all cylinders • 2. Compare the flagged cylinder's reading against its neighbors • 3. Add oil and retest (wet test) to isolate rings vs. valves • 4. Follow up with a leak-down test to confirm the exact leak path
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,060
5,062
1,440
Inspect and replace a leaking or damaged cylinder head gasket/valve
4
Professional Required
150
900
4.5
1. Confirm the leak-down result points to a head gasket or valve seat • 2. Remove the valve cover/head as required for access • 3. Replace the head gasket or recondition the valve seat • 4. Reassemble to torque spec and verify compression returns to spec
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,061
5,063
1,441
Swap spark plug and ignition coil to confirm the cylinder
1
Easy DIY
15
45
0.6
1. Remove the coil and plug from the misfiring cylinder • 2. Inspect the plug for fouling, wear, or an incorrect gap • 3. Swap the coil with a known-good adjacent cylinder's coil • 4. Clear the code and see if the misfire follows the coil or stays with the cylinder • 5. Replace the plug and/or coil based on the result
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,062
5,064
1,441
Test and clean or replace the cylinder's fuel injector
2
Moderate DIY
40
180
1
1. Perform an injector balance or ohms test on the affected cylinder • 2. Swap the injector with a neighboring cylinder to see if the misfire follows • 3. Clean the injector on an ultrasonic bench or replace it • 4. Reinstall with new O-rings and clear codes
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,063
5,065
1,441
Run a cylinder compression or leak-down test
3
Moderate DIY
20
80
1.5
1. Disable fuel and ignition for a dry compression test on all cylinders • 2. Compare the flagged cylinder's reading against its neighbors • 3. Add oil and retest (wet test) to isolate rings vs. valves • 4. Follow up with a leak-down test to confirm the exact leak path
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,064
5,066
1,441
Inspect and replace a leaking or damaged cylinder head gasket/valve
4
Professional Required
150
900
4.5
1. Confirm the leak-down result points to a head gasket or valve seat • 2. Remove the valve cover/head as required for access • 3. Replace the head gasket or recondition the valve seat • 4. Reassemble to torque spec and verify compression returns to spec
null
estimated
estimated
obd-editorial-us-aftermarket-v1
null
5,065
End of preview. Expand in Data Studio

🔧 MechanicDB — OBD-II Diagnostic & Repair Database (Free Sample)

Full dataset: mechanicdb.dataengineered.io · $49 Standard (SAE) · $149 OEM Complete, one-time → Buy Standard · Buy OEM Complete · the same sample on Kaggle

The free developer sample of MechanicDB: an automotive dataset mapping OBD-II Diagnostic Trouble Codes (DTCs) to authored repair procedures in consideration order with DIY difficulty ratings, parts-cost ranges (USD), labor-hour estimates where known, and step-by-step instructions.

90 curated codes (75 SAE-universal + 15 manufacturer-specific across makes like Ford, Toyota, BMW, Audi) with the same tables and columns as the full commercial dataset (the Parquet files here also carry a pandas index column, __index_level_0__) — the most-searched codes (P0420, P0171, P0300, …) so you can prototype joins, pipelines, and apps before licensing.

Tables

Config Rows Description
dtc_codes 90 Code registry: DTC, system category, OEM flag/make, fault family, short description, detailed technical explanation
diagnostic_fixes 326 Repair procedures in authored consideration order, with difficulty, parts-cost range and labor hours where estimated, action type, cost and labor status, cost basis, rationale, and step-by-step instructions
replacement_parts 449 Part mappings per fix with catalog search URLs; a row can also name a tool, a scan or programming session, or a rental
dtc_fixes_joined 326 Pre-joined analytical view (codes × fixes) for one-file ingestion

Row identity: SAE rows are unique by dtc_code; OEM rows by (oem_make, dtc_code) — the same manufacturer-range number legitimately means different things on different brands.

Companion files: ordering_metadata.json (procedure order), cost_metadata.json (cost basis behind each cost_basis_id, and the parts_cost_status / labor_status vocabularies), and identity_metadata.json with the filtered identity_map.csv / identity_map.parquet and identity_events.csv (stable references; see IDENTITY.md).

Procedure ordering

The supported legacy-named probability_rank is the authored order for considering diagnostic inspection or repair procedures within a code. Execution depends on each procedure's prerequisites and findings. It does not represent measured cause likelihood, repair success, severity, urgency, or minimum cost. The accompanying ordering_metadata.json records the OBD-II ranking basis as authored_family_order.

Quickstart

from datasets import load_dataset

joined = load_dataset("Ichlibitiche/mechanicdb-obd2-repair-sample", "dtc_fixes_joined", split="train")
p0420 = joined.filter(lambda r: r["dtc_code"] == "P0420")
for fix in sorted(p0420, key=lambda r: r["probability_rank"]):
    print(fix["probability_rank"], fix["fix_title"], fix["difficulty_level"])

The full dataset

Full dataset This sample
DTC codes 15,886 (9,249 SAE + 6,637 OEM / 32 makes) 90
Repair procedures 56,729 326
Parts mappings 75,055 449
Fault families 647 (linked)

Self-serve commercial licensing with instant download: mechanicdb.dataengineered.io · also on GitHub and Kaggle.

Provenance & license

  • Code-to-definition mappings compiled from an MIT-licensed SAE J2012-derived public compilation (attribution preserved in the source repos); repair procedures, difficulty ratings, and cost ranges are original editorial content from a deterministic, test-gated pipeline. Cost and labor values are editorial (parts in US dollars assuming aftermarket parts, labor in hours), not quotes; unknown values are empty.
  • License: ODbL v1.0 (attribution + share-alike).

⚠️ Repair steps are educational reference material, not a substitute for the vehicle manufacturer's service manual. High-voltage (hybrid/EV) and SRS/airbag work calls for the manufacturer's safety procedure whatever the difficulty rating; if you cannot follow it, leave the work to a qualified technician.

Downloads last month
198