instruction
stringlengths
40
29.6k
Currently, I'm using a pan tilt bracket that works with the servos I have (spark fun product 9065), and are generic to all servos. However, servos aren't accurate enough. I'm looking at other options, but have limited knowledge about them. What would you recommend? An important consideration is that I need my motor to ...
I'm looking at laser scanners and I see a huge range of detection distances. The furthest I've see are 30m if you exclude the very expensive ones that claim up to 150m. My question is what is the reason for the huge difference in range/price. I would think that with a laser it wouldn't be that difficult to detect so...
I haven't made or flown any quadcopter, but I am fascinated by them. But when looking at the frame of a lot of designs, after whachting this video I wondered why a lot the frames are in an X shape. Since the most efficient shape would according to the video be something like this >-<, where each corner is 120°. I also ...
How do you know if a commercial driver is working with trapezoidal or sinusoidal commutation? If you measure the 3-phase voltage applied to the PMSM by means of an oscilloscope, will you see a difference?
The last robotics project I worked on involved autonomous outdoor navigation, using a microcontroller for lower-level control and a computer for image processing and decision making. I worked more with the higher-level software and another guy on the team did the electrical and embedded systems. I would like to be capa...
I'm doing a project related to telemetry, and I want to make ArduPilot (programmed with ArduPlane 2.73) send through a serial port the sensors informations such as height, GPS position, etc.. I have tried to use ArduStation, but I could not change its firmware to do what I want. The idea would be to read the Ardupilot...
I am trying to implement a line following robot that can solve mazes similar to the Pololu robots you can watch on youtube. My problem is the maze that I am trying to solve is looped and therefore simple Left/Right hand rule can not solve the maze. I have done some research and think either Flood-Fill or Breadth-First-...
I'm trying to understand how noise is represented for accelerometers, gyroscopes, and magnetometers so that I can match the requirements of my project with the standard specs of these sensors. I want the output of a 3 axis inertial sensor to be values in meters/sec/sec, gauss, and radians/sec for each axis, and noise ...
I want to do a project where I control motors, and the arduino seems ideal for that. However, I'm going to need to do quite a bit of processing on the back end first. Connecting the arduino to a computer isn't an option, because it has to be quite mobile. Does anyone have any experience controlling arduino with raspber...
I was wondering if it is possible to plug a motor shield on top of an Ethernet shield, even though the direction pins on the motor shield would be connected to the same pins as the spi bus. I was thinking that it would work if, in the coding, I disabled both chip selects on the Ethernet shield before I used the motors...
TL;DR: Can anyone point me to a good adaptive path fill algorithm? Hey there, my name is James, and my daughter built an awesome painting robot with her friends over at Evil Mad Scientist labs, even brought it to the white house, very fun stuff! Anyways, I'm a web programmer by day, and though it might be fun to try an...
3D CAD: After some editing: I'm building the frame myself from aluminum and polycarbonate. EDIT: all frame is polycarbonate except of the arms (and all screws & nuts & washers)), they are form aluminum covered in polycarbonate. the total length (from one motor to another) is exactly 60cm Approximate Mass: 1.736 kg Wha...
If a motor has more Power (W) from another it means that it is better?
Just out of curiosity, can the concept of a Quadcopter be applied to an ROV? Would it work the same way underwater as it would be in Air? If not what kind of modifications it would take to implement that idea, underwater?
I am interested in starting a robotics club at my high school next year, since we don't have one, and I want to know what the pros/cons are of common kits. I already have a Vex kit since my uncle is one of the regional suppliers for Indiana, but I'm not sure that Vex is the best choice. What are the pros/cons of the ot...
I'm trying to find the optimal-time trajectory for an object (point mass) from point p0 with initial velocity v0 to point p1 with velocity v1. I'm considering a simple environment without any obstacles to move around. The only constraint is a maximum acceleration in any direction of a_max and optionally a maximum speed...
I'm endeavoring to prototype a challenging sorting mechanism inside a fridge and would appreciate any constructive tips on how to get from the specs to a plausible design. Problem The aim of the game is to identify and sort food items in the limited space of a fridge - such that a user would push their unsorted shopp...
It seems popular to build robotic systems with separate supplies for the electronics and motors/servos, but what would be involved in a circuit that powers both from one source? If it helps, here is my particular situation. I want to use a single 7.4V Li-Po pack to power an embedded system (2.5-6V operating voltage inp...
My team developed a filling machine for liquids which uses a piston to measure and deliver volumes 0.1 to 1 liters into bottles. It is built mostly with mechanical parts and we'd like to replace most of them with electronic ones. How do I build a machine to pull liquid from a reservoir and fills a bottle using a piston...
I'm looking for an electrical explanation of the statement here: Warning: Do not connect power (red + & black -) from the RC10 (A10) & RC11 (A11) connectors to the servos, just use the signal lines. Power the servos via the PWM Outputs connectors. These solutions will avoid the scenario that can possibly happen ...
I am building a robot where power density is critical, and looking into using lithium thionyl chloride (SOCl2) batteries. I will be drawing around 20A constantly and need between 12 and 17V. The batteries I have found so far are AA-sized and designed to deliver 100mA, 3.6v, 2.4Ah, and weigh 19g each. I could picture a ...
Are there any Python3 modules used to program robotic movement by declaring a device or component and then providing the instructions? I am not looking for modules that test the components.
So I built three little bots so far. One with a raspberry-pi, (6V motors), one with an arduino (12V motors), and another with an arduino but a hacked remote car (7ish, volt motors): The problem I have with all these is that the motors spin so fast the car just bumps into something in a few seconds. (I have a small ...
I'm looking for a way to create a non-rotating persistence of vision device. I have all the electronics set up but I'm stumped with the mechanical design. I tried these two designs: But these didn't work so well. Everything shakes violently and it doesn't go nearly as fast as I need (about 20 swipes per second) Any ide...
I have two Kinects (each on its own USB card) whose cameras I'm watching in RVIZ through OpenNI, and the structured light pattern of one is flashing intermittently - it's only there for a short flash every two seconds. Obviously, the structured light depth calculations only work if the pattern is always projected when ...
If a street is extremely crowded to an extent that the terrain is not visible from the point of view of the LIDAR (e.g. in google's self driving car), can it still manage to localize itself and continue to operate? I recall Sebastian Thrun saying that Google's car cannot navigate through snow filled roads since the onb...
I'm working on building a line follower robot and want to optimize its performance. It was suggested that I use a PID algorithm. I read a lot about PID but am confused a bit regarding following: I've calculated the error_value using $k_p * proportional + ...$ But regarding the change in the motor speed I'm confused as ...
I have built a Particles Filter simulator and I wanted to add the following functionalities. Limited Range Vision (Robot can see up to 50 meters) Limited Angle Vision (Robot can see within a certain angle w.r.t its current orientation. e.g. If the current orientation is 30 degree then it can see in the range from 0 t...
I was considering using a Raspberry Pi controlling a USB Relay to dim 12V LED lights, but I'm having trouble finding a solution that isn't a simple ON/OFF. What type of device would I need for dimming?
I am interested in using this miniature motor Squiggle Micro Motor to create very tiny horizontal movements. However, due to very limited space, I can only place it vertically within my project. Assuming this motor is placed as follows, how can one adapt it to simultaneous movement at a right angle? (Ideally with the X...
I have no problem in reading circuit schemes, connecting wires, resistors etc. (basing on for example instructables.com), but I've only tried to learn Java (a while ago) and it's difficult to me to find out what's going on with all this C-code-stuff. Are there any tutorials that are focused on the programming part? tha...
Many robot applications (actually - the most practical and appealing ones) include the robot's reaction to (and impact on) the evironment, e.g. due to stochastic nature of the environment (e.g. when robot should handle non-rigid objects like clothes) or due to the variability of environment (e.g. harvesting robots shou...
Hy, I just found useful to post my idea here. I've seen videos about automated quadcopters: http://www.ted.com/talks/raffaello_d_andrea_the_astounding_athletic_power_of_quadcopters.html and http://www.ted.com/talks/vijay_kumar_robots_that_fly_and_cooperate.html. I surfed pages from the companies presenting this resea...
If this has already been answered, by all means please point me to it. I am in the process of building a quadcopter which I eventually plan to run autonomously by allowing it to track an object and take a video feed of it moving. GPS is one of the options I've considered, basically: GPS antena on moving object (person...
An answer to the question Why are quadcopters more common in robotics than other configurations? said: You need 4 degrees of freedom to control yaw, pitch, roll and thrust. Four props is therefore the minimum number of actuators required. Tricoptors require a servo to tilt one or more rotors which is more mechanicall...
I am trying to launch a file from remote computer but I could not success. Actually I can connect to remote computer but I think the problem is with including a file from remote computer. In other words, I am looking for a machine tag for include. Here is the my code: <launch> <group > <machine name="marvi...
For a DC motor with a stall current of 950 mA, what should the H-bridge's current rating be? What will happen if we use our H-bridge L293D whose max. output current is 600 mA?
I found a good explanation on how to remove accelerometer bias (when on flat table only one axis should show values, the other two should be 0). I've calculated S and B factors (page 3): Record $B_x^{0g}$, $B_y^{0g}$, $B_z^{0g}$, $S_{xx}$, $S_{yy}$, and $S_{zz}$ in EEPROM or flash memory and use these values in all ...
For Halloween, I'd like to build a spider that drops from the ceiling when it detects motion and then rewinds itself back up to scare the next kids. I already have a lightweight foamish spider from Hobby Lobby that I'd like to use, but I need help adding the smarts to it to scare the kids. Ideally, it'd be able to dete...
I've already asked a related question (accelerometer bias removal) here on robotics and got a bit better results on corrected accelerometer output. To get even better results I found the calibration equations (7th & 8th paragraph) from Vectornav which are just a bit enhanced than the solution in the linked question: H...
I have a project which requires a robot to move around a room with a flat surface (concrete floor). The robot must carry a laptop. I estimated that the total weight would be 6-7kg (including motors, battery, laptop, motor controller board and other mics items). I would like it to move at about the same speed as a Roomb...
I'm starting to attempt to fly FPV on my quadrotor. I am using a FrSky D8R-II 2.4 GHz frequency hopping diversity receiver (two antennas) for control and recently added a no-name 910 MHz 1.5 watt analog video transmitter for FPV flying: When the video transmitter is powered up, my control range drops from about 1.5km ...
Our robot has a circular array of 12 sonar sensors that looks like this: The sonar sensors themselves are pretty good. We use a low-pass filter to deal with noise, and the readings seem pretty accurate. However, when the robot comes across a flat surface like a wall, something weird happens. The sonars don't show read...
I want to compute an existence probability of an object in a sensor fusion on the high level (having from each sensor list of objects already filtered with e.g. Kalman Filter). There are these formulae: $$LR(G)_{old} = \frac{p(Ex_{out})_{old}}{1 - p(Ex_{out})_{old}}$$ $$\alpha = \frac{p(Ex_{in})_{old}}{p(Ex_{in})_{old}...
What is the name for the transfer function, GH, in a simple feedback control system like $$y=\frac{G}{1+GH}u$$ What do you call G? What about (G/(1+GH))? I am confused by the fact that that "open-loop transfer function" and "Loop transfer function" are used to mean GH by different people. Which is academically correct...
I'm quite new to mechanical engineering and not familiar with gears and motors. A few days ago, I bought a second-hand GWS servo motor for my project, and it didn't include gears. Can someone help me understand the correct measurement of my motor so I can buy the correct gear to fit on my servo motor. Specifically, the...
I am software engineering student and don't know much about hardware. I recently have started a project in my AI course. The project is playing a 3x3 tic-tac-toe game between computer and a human. In a tic-tac-toe board, suppose you play first and you put a cross mark in a certain place.(in tic-tac-toe board your posi...
I want to give my robot a differential mechanism for the system of turning and steering. Considering the case of turning a right-angled corner, the robot will achieve this by following a gradual circular arc through the intersection while maintaining a steady speed. To accomplish this end, we increase the speed of the ...
I am thinking of creating a robot that can navigate using a map. It is controlled from a PC. An 8-bit controller performs low level tasks and the PC is doing the image processing. I plan to implement it in a single room where the robot is placed and the robot and environment are tracked by a camera from a height or fro...
I'm moving from controlling a robot arm with basic time based motors controlled using a raspberry pi and python to a more advanced robotic arm that has servos (e.g HS-425BB). With the time based motors I must constantly keep track of the arms position (guess work) and make sure it doesn't over turn. Do servos automatic...
I'm a newbie to Electronics/ Robotics, but I love to do it as a hobby. So I want to build a circuit (a really small in size would be much better) with a motion sensor that can communicate data (Basically when it sense a motion send a signal) to my computer over Wifi. Is this something possible? If so how do I do it, ...
I am building a 2 wheel robot to carry 7KG of load. I used this link to get the torque required for each motor which is 11Kg-cm. So I choose 2 of these motor which has 36Kg-cm(2x more) torque. I noticed that the stall current is 14A. Can I use Adafruit Motor Shield for Arduino which is rated 3A peak current capability...
We are using ArduIMU (V3) as our Quadrotor's inertial measurement unit. (we have a separate board to control all motors, not with ArduIMU itself). Now we have a problem with ArduIMU's sensors output. When we put our quadrotor steady on the ground with motors on, instead of getting 0 degree in roll and pitch we have a ...
I was at a Robotics conference earlier today and one of the speakers mentioned robots not being able to function as well in a crowd because they can't single out audio like a person can. Why can people single out audio so well? And what would it take for a robot to do the same? I'm aware of Active Noise Reduction (A...
What is the minimum amount of power that a beaglebone needs to start up? This would be with no peripherals attached besides host usb. The getting started guide claims that it can run off of a computer's usb power, but makes no mention of how many amps are actually needed. I saw a mention of older kernels limiting cur...
How would you motorize the joints in an Iron Man suit? You need something fairly shallow, I would think, probably dual servos sitting on either side of an elbow or knee joint or either side of your hips, but how do you get motorized action there without dramatically adding to the thickness of the joint? Bicycle-style ...
I've been thinking about starting a quadcopter project, maybe building it from scratch. One of the main barriers-to-entry for me is the motors: it seems like most quadcopters use brushless motors. I have some experience with DC motors and using PWM signals to regulate speed, but no experience with brushless motors. As ...
I have some crude time based motors taken from a robot arm that we upgraded to proper servos. I want to be able to power a conveyor belt with one of them and I was wondering how I would go about the following setup: A ball drops through a hole onto the conveyer belt hitting a lever switch on its way through. This switc...
Whenever I try using openni_launch, it works normally, however, when I try viewing an image using the kinect's rgb or depth camera, or even recording a simple bagfile with data from the kinect, I am unable to see any picture and rosbag does not record any data, and after a few seconds of running image_view or rosbag re...
Im designing a differential steering mechanism for my robot. Supposing my robot is going in a straight line and I want it to change it direction by a certain angle( $θ$ in the diagram). What should the velocity ratio be of the 2 wheels so that it gradually turns and starts moving along a line that is $θ$ degrees to the...
I am a graduate student trying to make my own Line follower Robot for my minor assessment, I've all hardware parts and all data-sheets with me, I've attended a workshops of Robotics and studied a lot on Line follower robot. I have a good knowledge of C Programming and Embedded systems, but the problem is I've a very li...
I have been looking online for a while, and I cannot seem to find any steppers without any torque ratings. (Operating torque, not holding torque.) I even looked on hobby sites that usually have all the ratings, including Adafruit and Sparkfun. I only have found one ever that said the operating torque, however, it didn'...
I need my robotic arm to ring a desk bell. I one on the maplins site usb robotic arm. It does seem very slow. What can I hack on it to boost the downwards and upwards speed. I need it hit the bell tip/platform quickly once or twice. This is purely a LOL project for work. Ever time we get an order we want the arm to...
On my stepper's datasheet, it has the category "rotor torque" (labeled in N-CM). What does that mean? Is this the torque it has can supply when turning? (Hopefully)
I have a APM 3DR Quad with a 3DR radio telemetry kit. I would like to send real-time sonar data to my laptop (running Windows 7) in order to manipulate it in an additional Arduino Sketch. The sonar sensor is connected to an Analog In channel on my Arduino. That data is processed for altitude calculations, and I woul...
How do you calculate or update the position of a differential drive robot with incremental sensors? There is one incremental sensor attatched to each of the two differential wheels. Both sensors determine the distance $\Delta left$ resp. $\Delta right$ their wheel has rolled during a known time $\Delta t$. First, let's...
What is the difference between a Robot and a Machine? At what point does a machine begin to be called a robot? Is it at a certain level of complexity? Is it when it has software etc?. For instance: A desktop printer has mechanics, electronics and firmware but it is not considered a robot (or is it). A Roomba has the sa...
I would like to know if there are any other solutions to implement slip compensation into a Half-Size Micromouse other than the conventional method. I have spoken to a few Japanese competitors, and they told me that the only solution they have to such a problem is creating a table of predetermined values and using thes...
I am working on a homemade vending machine project that serves milk and cookies, using arduino and some basic servos and stuff. The problem is: I really have no clue on how to protect the milk to last long, or how to even know if the milk is still ok to drink.. All I really know is that air is bad for the milk (and the...
I have a box (cuboid) lying on floor or table. So there are 6 surfaces of the box and 1 surface of the floor. If I take each pair of surface such that the surfaces are "adjacent" to each other, I get two kind of pairings: 1) two surfaces of the box: the surface normals of the surfaces diverge from each other. 2) 1 surf...
I’m trying to inject some kind of rubber around an aluminum strut to form “feet” for a robot. I’ve already milled the mold, but I’m having trouble finding an inexpensive and readily available rubber compound that will cure without exposure to air. Ideally it should cure to about the consistency of a silicone O-ring. I’...
I'm trying to control the speed of this motor, with this motor driver and pic16f690. pwm in my program 5 kHz frequency (0.2 ms period) Starting with 50% duty cycle the motor doesn't run. But moving from say, 80% to 50% (i.e. program my PIC with 80% duty cycle, and then re-program it with 50%), the motor will run at 5...
I made a small crawler robot a little while ago that had two legs with two degrees of freedom each, so 4 RC servos total. While I was programming the movement of the legs I noticed that they moved rather stiffly. It makes sense that the RC servo's internal controller would have a very quick response to position command...
I am working on a robotics project with C++ (drawing signs on board), on CRS CataLyst5 arm. I have faced a problem: I have many methods move in different directions, goToLocalizations, etc, but the problem is that when I run many of them in main without Sleep() function between each function they does not run properly....
I am in the concept phase of a driving robot. The two wheels on the front axle will be powered, while the rear will be dragged along. The rear is also responsible for steering but this has noting to do with my question. Since the robot is required to make relatively sharp turns at high speed. Therefore I have two optio...
I've got an arm attached to a shaft. The arms dimensions are 40x5 inches the arm weights about 10 lbs. If I have a wind acting on the side of the arm, how would I translate the wind force into torque on the shaft? To give some more information, I'm rotating the arm using a stepper motor, and I would like to know how to...
I'm going to be embarking on an autonomous robot project and I was going to be using GPS to navigate to waypoints (I'm aware of the margin of error when it comes to localization with GPD but I live in a lovely area with many open fields). I was going to use Adafruit's Ultimate GPS Breakout board with my RaspberryPi, a...
For the Dagu Wild Thumper 6 Wheeled platform, or any multiple motor system, do I really need 1 battery for each motor? Or should I just buy 2 for either side of the platform. In addition, for larger motors like the ones on this platform, how do I deal with the power generated from a coasting motor? I want to jump into ...
I'm in the process of writing my own simple quadcopter controller for experimental use, and I'm having trouble getting my head around how to convert from the degrees which my PID controller demands to an appropriate 1k-2k range for PWM output. For example, take the roll axis on a '+' configured 'copter (pseudo-code): s...
I bought this MPU-6050: link According to the manufacture site, the sensor logic level is 3.3V (though the ebay page says Power supply :3-5v) Should I use a 4 channel Bi-Directional Logic Level Converter (like this one) for the SDA, SCL, INT channels? or can I connect it directly to my arduino nano? I saw some places t...
I have a USB webcam and a WiFi module which it can convert Serial data to WiFi and vice versa. The question is can I simply convert the data coming from the webcam to serial with a USB to Serial IC (like FT232R ) and then hand it over to my WiFi Module? Update: The WiFi module DataSheet is here
Consider a differential drive robot that has two motorized wheels with an encoder attached to each for feedback. Supposed there is a function for each DC motor that takes a float from -1 to 1 and sets the PWM signals to provide a proportional amount of power to that motor. Unfortunately, not all motors are created equa...
I am working on a robot with focus on speed. At the moment I am looking for a suitable motor but it would help if I understood the difference between the various options. To provide some background, I have not worked with RC model components before, but I think this is the only place for me to find the components neede...
I know that the Complementary Filter has the functions of both LPF and HPF. But I think my understanding on the principal behind it is still unclear. I am quite new on digital signal processing, and maybe some very fundamental explanations will help a lot. Say I have a Complementary Filter as follows: $$y =a\cdot y+(1-...
Need a way to dispense micro liter amounts of water (lets say 1-10ul). Only thing I've found is piezoelectric dispensers and they are >$100. Any suggestions? I can build, but preferably would be an off-the-shelf component.
I'm working on a robotics project, and I am using grayscale sensors to automatically follow a black line: turning 90 degrees, going round in a circle, and passing through gaps in the lines etc. I was wondering what is an effective way to detect the colours and move it through the lines, with five or six grayscale sens...
I'm doing some groundwork for a project, and I have a question about the current state of SLAM techniques. When a SLAM-equipped device detects an object, that object's position is stored. If you look at the point cloud the device is generating, you'll see points for this object, and models generated from it will includ...
I'm trying to put together a simple simulation for a delta robot and I'd like to use forward kinematics (direct kinematics) to compute the end effector's position in space by passing 3 angles. I've started with the Trossen Robotics Forum Delta Robot Tutorial and I can understand most of the math, but not all. I'm lost ...
I want to use my atmega8 uC as a h-bridge. Can anybody give me the source code using C, so that the microcontroller acts as an H-Bridge.
I am using SIM900A for some purpose and want to know the number of the sender from where a message comes. I am unable to find the specific AT command related to receiving message which give me number from where latest message comes. I had used AT+CNMI (it corresponds to notification regarding latest received message), ...
I am planning to build a robot. 1) What free or low cost robot modelling tools exist.
I have been studying about building a tricopter. But I couldn't find the design calculations or mathematical modeling of the tricopter any where over the internet. What are the mathematical relationships or equations of motion and forces in tricopter? How do I calculate the requirements of the structural design and ...
This might be a out of league question and may seems to be very odd.I am using multiple Arduino UNO boards over network and want to assign a GUID and Serial number to each board so that when ever they send any data to a central server, server is able to find which Device it is if we have assign name for each device. f...
I have several APM 2.5 boards and need to identify them based on some globally unique hardware signature that does not change with programming. Arduinos and atmel AVR chips in general do not have (also this thread) an accessible serial number. However, it seems that the Ardupilot has so many integrated sensors and othe...
I'm looking for a laser / photosensor pair (or product of similar function) for detecting when a beam is interrupted (no more than 3ft apart, probably more like 1ft). I'd like these to run off of 5V, since I'm using an Arduino. My main requirement, however, is that these parts have nice housings, ideally with some moun...
We hope to build a simple line follower robot and we got a problem when we were discussing about PIC programming. We planed to write a endless loop, check the sensor panel reading and do the relevant stuff for that reading. But one of our friends told us to use a timer interrupt to generate interrupts in definite time ...
I used to think that the higher GPS antenna position the better until I read the following on GPSd FAQ: One common error is to place the GPS or antenna as high as possible. This will increase multipath effects due to signal bounce from the ground or water, which can cause the GPS to mistake its position and the time s...
Background: I am implementing a simple Kalman Filter that estimates the heading direction of a robot. The robot is equipped with a compass and a gyroscope. My Understanding: I am thinking about representing my state as a 2D vector $(x, \dot{x})$, where $x$ is the current heading direction and $\dot{x}$ is the rotation...
I am implementing a simple Kalman Filter that estimates the heading direction of a robot. The robot is equipped with a compass and a gyroscope. Say at time $t-dt$, the compass reports a reading $\theta_{t-dt}$, and the gyroscope reports a reading $\omega_{t-dt}$. Then I assume from time $t-dt$ to $t$, the rotation rate...
In this paper, the author says that during SLAM process, pseudo segments that appear from any momentary pause of dynamic objects in laser data would make the map unsatisfied. How is this caused? If the dynamic object moved, won't laser data update and eliminate the segment of dynamic objects?