instruction
stringlengths
40
29.6k
I recently purchased at EY-80 from electrodragon: EY-80 All in one 9-Axis Motion Sensor (Gyro + Acceler + Magneto + Baro) I am having a hard time compiling the example code on my arduino: This is what is happening. So far, I am only copy and pasting the code. Any help? (I am somewhat new to programming, so don't ful...
I am about to make an rc car which uses a wifi connection. The body for the car would be made from aluminium and the wifi receiver will be placed inside this aluminium casing. How do I make sure that this will work? Would I be forced to change my material or can I just make an extension for the receiver and make sure ...
I am using an Arduino Uno to control an ESC for my (in progress) quadrocopter. I am currently using the servo library to control the ESC, which works great. Except.. A count of 100 is max speed, meaning I only have 10 speeds between 90 (stopped) and 100 (motor at full power) to correctly run my quadrocopter, I would l...
I'm trying to add my own robot in Morse 1.1 (using Ubuntu 12.04). I am struggling to add an armature actuator and armature pose sensor to an existing robot. Can someone please explain how this can be done (preferably with some sample code and using the socket interface). Thanks.
I searched for GPS devices that provide 1 sec updates to server, but I have not found any. I found this T=30s.Module has sent a monitoring data packet. After 12 seconds the server sends an acknowledgement. In 18 seconds later (T = 30s) module sends the next monitoring data packet Are there any products that take...
As I understand it, a Kalman filter uses a mathematical model of the robot to predict the robot's state at t+1. It then combines that prediction with information from sensors to get a better sense of the state. If the robot is an aeroplane, how accurate/realistic does the model need to be? Can I get away with simple po...
I'm trying to figure out a way that I can calculate the probability that a particle will survive the re-sampling step in the particle filter algorithm. For the simple case of multinomial re-sampling, I can assume that we can model the process like a Binomial distribution if we only care about one sample/particle. So if...
Basically, I want to detect an ultrasonic beacon in a radius around the robot. The beacon would have a separate ultrasonic emitter while the robot would have the spinning receiver. Are there any existing ultrasonic sensors that would meet this use case or am I stuck hacking one together myself? Is ultrasonic even the b...
Having read the article "This Car Has Electric Brains" in Popular Mechanics, August 1958 I have some questions. How practical were his methods? Was his work acquired by a car manufacturer or some other company? Were his methods developed further? How did his corner navigation work? I don't think he needed to know the d...
POMDPs are used when we cannot observe all the states. However, I cannot figure out when these POMDPs can be useful in robotics. What is a good example of the use of POMDPs? (I have read one paper where they used them, but I didn't find it obvious why pomdps should be used) What would be good projects ideas based on PO...
I have a WL v262 quadcopter and I want to control it using Arduino instead of the joysticks on the transmitter. I opened up the transmitter and saw that each joystick has 2 potentiometers on the PCB and that the voltage for each pot goes from 0-3.3V. I used arduino's PWM and a low pass filter and connected the output o...
A Google search on "bloodstream nanobots" yields thousands of results and just on the first page, many results of blog posts that date back to 2009. It is nearly 4 years later. I've had no luck in finding any information on actual APPROVAL of these bots. Are there any countries at all who have approved this? People se...
I am interested in getting an arducopter with an ardupilot(APM). I read through the documentation and from what I understand, ardupilot is the low level hardware and firmware that directly controls the motors of the arducoptor. I would like to know if there is a higher level programmatic interface to the ardupilot? Th...
For examples if i have this robotic arm: Example, for the base rotation (5th DOF in the clip at 0:58), we know that the Z axis for that joint will be the same as the Z axis for the base frame{0}, but I don't know about Y and Z axises of the base rotation respects to the base frame, should they be the same or not ? And ...
For a university course I have been asked to design a rough "specification" for a system that will deburr a plastic box that appears in a workspace. Due to irregularities in the boxes edges I cannot use simple position control and must use force control. I have so far decided on; Using an IR sensor to detect the box ha...
Suppose I have a particle filter which contains an attitude state (we'll use a unit quaternion from the body to the earth frame for this discussion) $\mathbf{q}_b^e$. What methods should or should not be used for resampling? Many resampling schemes (e.g. this paper) seem to require the variance to be calculated at some...
I would like to know if anyone here has used the Blueview SDK (Linux) for retrieval of images from the pings obtained by a multibeam sonar (P450, P900, etc.) ? If so, I'd like to know why would anyone get a null head when I trying to retrieve the head (eventually for the pings to be converted to an image) using the BVT...
I'd like some well put video series of like 30 videos. Or anything but it needs to thorough and in easy English...less mundane. So far all resources i have found either go upto resistors code or of projects that tell you do this and this and this and tada you got this. Is there really no online resource for people to l...
UPDATE: This exact problem has been solved in StackOverflow. Please read this post there for further explanation and a working solution. Thanks! I am working on an application where I need to rectify an image taken from a mobile camera platform. The platform measures roll, pitch and yaw angles, and I want to make it lo...
I am trying to build an advanced coloured lines following robot with the ability to differentiate between many different coloured lines and follow them. I am looking for the right sensor that will help my robot achieve its objective. As I was researching I came across the EV3 Colour Sensor which can detect up to 7 colo...
I am trying to get the usb.find command to work properly in a python script I'm writing on Angstrom for the Beagleboard. Here is my code: #!/usr/bin/env python import usb.core import usb.util import usb.backend.libusb01 as libusb PYUSB_DEBUG_LEVEL = 'debug' # find our device # Bus 002 Device 006: ID 1208:0815 # i...
Given a robot with 2 wheels with radius r on one axle with length D, I want to set the wheel speed so that it turns to an angle phi as fast as possible. The timestep t is 64 milliseconds. I thought the wheel speed could be set to v = ((desired_heading-actual_heading) * circumference_wheel_trajectory)/(2*pi * t * wheel_...
I'm just wondering that is there any case that when algebraic way can't solve the problem while the geometric can ? Cause I'm working on a 2DOF robotics arm This one, I know the length of L1 and L2, location that I want for the end effector, then I tried calculating the angles by using algebraic but it gave me cos(alph...
Is there a node or package that can send commands to /cmd_vel to move ATRV-Jr like 2 meters forward or turn it 90 degree to right/left? I don't want to tell the robot to move with specified speed. For example when I use this command rostopic pub /cmd_vel geometry_msgs/Twist '[1.0,0.0,0.0]' '[0.0,0.0,0.0]' the robot sta...
I am taking information for my project and I need to see libraries ans SDKs. Searching in the web I found that OpenNI has a lot of functions and when I try to found another SDK, I dont find any other. I am working with a Kinect and a XTION so I need an SDK who works in both. Is there any other SDK o set of libraries t...
I am trying to manually calibrate the on-board accelerometer of an APM 2.6 controller. I am using the following code (I found this somewhere, don't remember where) with Arduino 1.0.5 (in Windows environment) to fetch the accelerometer and gyro data: #include <SPI.h> #include <math.h> #define ToD(x) (x/131) #de...
I am totally new to the camera interface and usage in an Embedded project, and would like to use a CMOS vision sensor like this.This project further will be used to power a small robot with on-board video processing power using processors like ARM 9. I do have a limitation that until now I have worked only on 8-bit mic...
I am new to robotics and control and I have been thinking about how to deal with problems in real life. I have passed a course in control, but I do not have any idea about control for discrete/digital systems. There are a lot of robots and in general dynamic systems which are controlled by microcontrollers or computers...
I am currently working on a project for school where I need to implement an extended Kalman Filter for a point robot with a laser scanner. The Robot can rotate with 0 degree turn radius and drive forward. All motions are piecewise linear (drive,rotate,drive). The simulator we are using does not support acceleration, al...
I am planning on building a robot with wheels (later legs, if possible), that can move around the room and analyze certain things, using a couple sensors. In the later steps more functions such a grabbing are the things I want to add. Could you recommend me a micro controller? My concern about Arduino is that there are...
I am testing an industrial robot (ABB IRB 1410) using three simple Micron Dial gauges to get x,y,z values at particular point by varying Speed, Load and distance from home position. My questions are, Whether these three parameters influencing the repeatability or only the accuracy? Using dial gauges, without any relat...
I'd like to build a robot as small as possible and with as few "delicate" parts as possible (the bots will be bashing into each other). I was wondering if it was possible to use a small chip that could receive bluetooth/IR/wifi commands to move the motors, and in turn, send back feedback based on sensors such as an acc...
http://www.youtube.com/watch?v=4Vh_R1NlmX0 is from 2011 SWARM and shows RC aircraft or combat wings trying to hit each other in the air. Scoring a hit is pretty rare, and I'd like to increase a pilot's chances by using a computer targeting system. It would be an offline system that gets data from sensors on the airpl...
I'm building a project that uses a cell phone to control a microcontroller via Bluetooth. I've decided to use the HC-05 Bluetooth module. HC-05 Manual: http://www.exp-tech.de/service/datasheet/HC-Serial-Bluetooth-Products.pdf And the phone I'm using is the Nokia C3-00 (series 40). http://developer.nokia.com/Devices/Dev...
I'm trying to get a quad rotor to fly. The on board controller is an Ardupilot Mega 2.6, being programmed by Arduino 1.0.5. I'm trying to fly it in simple autonomous mode, no Radio controller involved. I've done a thorough static weight balancing of the assembly (somewhat like this: http://www.youtube.com/watch?v=3nEvT...
I am a beginner of ROS, Kinect and Ubuntu. What I want is to visualize Kinect's data on rviz environment then run object recognition on it. I've tried a few tutorials but had no luck. All I got was an empty rviz world. Since I am a beginner I would appreciate any step-by-step instructions (preferably for hydro or groov...
If not all, but major types of lawn mower robots are rotary mowers. I presume1 that reel mower is more efficient, and is said to leave a better lawn health and cut. So, why industry go to the other option? 1 - I'm assuming the efficiency, as electrical rotary mowers have at least 900W universal-motors or induction mot...
I was wondering, my team and me are working on a robot communication-oriented and we wanted to add speech recognition on it. What technology should I use ?
That is what I came to understand while reading here and there about flashing a new bootloader/understanding what a bootloader is etc etc The bootloader is supposed to be the first thing that runs when I power up my Arduino Duemilanove (or micro controllers in general). It does some setup then runs my app. It also list...
I'm a newbie in UAV stuff, your advice would be very helpful, i want to start mapping using fixed wing UAV, but my main choice was APM 2.6, but after some researches, i found that APM 2.6 won't be actively maintained in the future because the future releases will be PixHawk. i wonder if i should choose APM 2.6 for its ...
Everybody here is probably aware of the Sharp distance sensors (GP2Y0 series, e.g. GP2Y0A02YK0F). They use a diode to emit infrared light and measure the angle of the reflected light with a PSD (i.e. they do triangulation). They seem to be the only producers of this technology. I am only aware of a few similar but inco...
We are planning to recalibrate ABB IRB 1410 robot and conduct series of accuracy & repeatability tests using FaroArm. My questions are i) Is there any physical identification marker on the robot which can be used to identify the location of base co-ordinate frame? ii) If locating the base frame is not possible, can acc...
BEAM robotics seem to be a good approach to teach learners about electronics in robotics. But can these robots be like regular programmed "cognitive" robots? Can these robots, with just analog circuits, take us to the level of robotic assistants, worker robots and other kinds of self sufficient autonomous robots? I spe...
I'm having an event for a boat race.Simple boat has to be made.All i have is 5 days.The restriction is 24V motor not more than 1000 rpm.What best material and shape will you suggest to make a boat.I know basic circuits.We have to make a boat with a wired circuit.That circuiting i can do but what can be an ideal shape f...
I'm having a problem with controlling my BLDC motor when starting up and when running in low rpm. I have a custom board to measure rotation of the motor using an optical sensor and send servo pwm commands to an esc. The problem is, that I can't start the motor smoothly. When I slowly increase the control signal, it sta...
I am beginning to learn about the hardware aspect of robotics, and in order for a lot of this new information to be useful to me (whether on this site or elsewhere) I will need a basic understanding of the terminology. One thing that comes up repeatedly is different electric motors: servo, DC motor, brushless motor, st...
In software engineering startups, you generally go to a room with a computer or bring your own laptop, and write code. I'm interested in how robotics startups work: Is there a separate location for designing the robots? Take for example, Anki. Do they have separate research labs for designing robots? How does a robot g...
I have a BOE bot PBasic2 stamp based robot that came with rubberband "tires" for the wheel. however, they are very tight and I can't figure out how to get them onto the plastic hubs. the furthest I've gotton was mostly covering the outside, but when trying to make it less crooked it came off again. is there some trick ...
I'm programming a PIC16F77 with ProPic 2 which communicates via serial port. As I don't have this port in my PC, I used serial to USB adapter. I'm using ICProg in Windows 8. I've proggrammed it before but it was in Windows XP using the driver who specifies in http://www.ic-prog.com/index1.htm and worked perfectly. But ...
I have a Micro Magician v2 micro controller. It has a A3906 Dual FET “H” bridge motor driver built in. In the manual it states "Electronic braking is possible by driving both inputs high." My first question is, what is the purpose of these brakes? If I set the left/right motor speed to 0, the robot stops immediately a...
Over the last couple of years I've had good success with my technology startups and now looking to enter into robotics. I was interested in robotics and automation ever since I was a kid (yes, that sounds nerdy). So my question is: Where to get started, what to build? and how to sell? And lastly, how difficult it is to...
I am wondering if it would be possible to get Kinect to work with Udoo board (Quad). I have found that there is now support for ROS + Udoo. Also saw a question asked about Xtion + Udoo which shows some more interest. It would really be great if it could be possible for Kinect+Udoo. Was hoping to implement perhaps a min...
I'm building a quadcopter. It will be controlled by a Beaglebone black with several Sensors and a cam. I new to the quadcopter stuff, therefore it would be nice if someone could have a look at my setup before I buy the parts. Frame: X650F - 550mm Battery: Turnigy nano-tech 5000mah 4S 25~50C Lipo Pack Motor: NTM Prop D...
I would like to ask a question about zero crossing event in a trapezoidal commutation on a brush-less DC motor. Here is a waveform that shows that the zero crossing event occurs every 180 electrical degrees in a sinusoidal commutation: But what about trapezoidal commutation. Here is the waveform that I found about the...
I would like to ask a question about zero crossing event in a trapezoidal commutation on a brush-less DC motor. Here is the waveform that shows that the zero crossing event occurs every 180 electrical degrees in a sinusoidal commutation: But what about trapezoidal commutation. Here is the waveform that I found about t...
I'm programming Lua for controlling computers and robots in-game in the Minecraft mod ComputerCraft. ComputerCraft has these robots called Turtles, that are able to move around in the grid based(?) world of Minecraft. They are also equipped with sensors making them able to detect blocks (obstacles) adjacent to them. Tu...
I am trying to simulate a quadcopter model on Simulink. I want to implement a PID controller for each of X,Y,Z and phi,theta, psi angles. PID gets the error, as input, which is to be minimized. For the X,Y and Z, the desired values are entered by the user and the actual values are calculated from the accelerometer data...
I'm reading Probabilistic Robotics by Thrun. In the Kalman filter section, they state that $$ x_{t} =A_{t}x_{t-1} + B_{t}u_{t} + \epsilon_{t} $$ where $\epsilon_{t}$ is the state noise vector. And in $$ z_{t} = C_{t}x_{t} + \delta_{t} $$ where $\delta_{t}$ is the measurement noise. Now, I want to simulate a system in...
I need to find a way to solve invrese kinematics for Comau SMART-3 robot. Could you give me a few hints where to start looking? I have no idea about robotics and I couldn't find an algorithm for this specific robot.
From what I've read so far, it seems that a Rao-Blackwellized particle filter is just a normal particle filter used after marginalizing a variable from: $$p(r_t,s_t | y^t)$$ I'm not really sure about that conclusion, so I would like to know the precise differences between these two types of filters. Thanks in advance.
I Have an old audio amplifier that has those switches to turn it on. I'm looking for the simplest motor/robotic arm (or any other relevant component) to control this switch - eventually via Raspberry Pi . Are there any options ?
Can a gyroscopic sensor (comparable to the type that are typically used in smartphones) that is embedded in this black object that is rotating around the X axis measure the number of rotations around the X axis if the object may or may not also be rotating at the same time in random ways (number of partial or full r...
We want to create robot that will localize itself by the signals of wifi routers. Which sensors should we buy to detect strength of 3 WiFi signal? Which of following is necessary for us? http://www.dfrobot.com/index.php?route=product/category&path=45_80 or can be any other more suitable variants? We are using arduino a...
I previously thought that an accelerometer on a quadcopter is used to find the position by integrating the data got from it. After I read a lot and watched this Youtube video (specifically at time 23:20) about Sensor Fusion on Android Devices, I seem to get its use a little correct. I realized that it's hard to filter ...
I need help in differentiating between AI and Robotics. Are AI and Robotics two different fields or is robotics a subject in AI? I want to pursue a career in AI and Robotics. So I need your valuable suggestion. I searched the web and also some universities that I want to apply and I cannot find any such thing that I am...
I am having difficulty sustaining a connection between my Raspberry Pi (Model B running Raspbian) and my Arduino (Uno) while sending signals from the Raspberry Pi to a continuously rotating servo (PowerHD AR- 3606HB Robot Servo) via Python. I'm not sure if there is a more efficent way of sending servo instructions via ...
I've spent quite some time researching this, but most of my Google search results have turned up academic research papers that are interesting but not very practical. I'm working on a target/pattern recognition project** where a robot with a small camera attached to it will attempt to locate targets using a small wirel...
I've gone through tutorials on how to build circuits and control dc, stepper, and servo motors. I may not understand everything about them internally, but i have a good basic foundation. Now i'm at a loss for where to go from here. I'm more interested in learning how to make mechanical devices with them than just t...
at the moment I am creating an android program, that will steer my simple, 3 wheel (2 motors, 1 for balance) robot to move online following the path drawn by user on his screen. The robot is operated through WiFi and has 2 motors that will react on any input signals. Imagine user drawing a path for this robot on smartp...
Orrery is a clockwork model of the solar system. I am trying to emulate one in 2D. Now, to emulate, I need to know what goes on inside. Can someone please explain the basic principle behind the clockwork? Or direct me to a resource that will explain all the machinery inside a simple Orrery.
My task is to apply forces to control 3-dof parallel manipulator. Forces are applied to linear actuators, friction is neglected. End-effector of a robot is supposed to follow generated path; for this example, let it be a simple circle. So far I have made a simplified 3d model of robot and calculated inverse kinematic...
I'm running a kk2.0 + 4 20A Multistar ESCs + 4 EMax GF 2215-20 motors + 4 Slow Fly Props After about a foot off the ground, the entire quadcopter starts wobbling like crazy (no auto-level). Any ideas? I'll add some video if needed.
I am in the process of creating a Power Prediction Model for the Hubo Robot. The Robot has 38 Degrees of Freedom and has a computer some sensors and motor boards. The motors are powered through Motor Boards. All these boards are powered through a main power board that exists at the robots chest. My model should be able...
In continuation of the question I asked here: Quadcopter instability with simple takeoff in autonomous mode ...I'd like to ask a few questions about implementing a basic PID for a quadrotor controlled by an APM 2.6 module. (I'm using a frame from 3DRobotics) I've stripped down the entire control system to just two PI...
Given a 12' x 12' field (4m x 4m), a reasonably cheap 3-axis gyro sensor and accelerometer, and compass, I plan to design a device capable of tracking its position to sub-centimeter accuracy for a minute of motion or so. The device has a holonomic drive system, capable of moving any direction at a maximum of about 8mph...
I am a Computer Science student entering my last year of college. I'm pretty sure Robotics is what I want to eventually be doing based on my interests in AI and embedded systems. I've seen a lot of topics that covers Robotics such as: control theory, signal processing, kinematics, dynamics, 3D simulators, physics engin...
I need an app that can do live monitoring of whether each seat in an auditorium is occupied, so visitors can load the app and see where to sit. The auditorium has a relatively flat ceiling 4m high, and the seats are .5m wide. The hardware cost per seat needs to be $5. I'm looking for all solutions. Web cams, pre...
I'm trying to get an extended Kalman Filter to work. My System Model is: $ x = \begin{bmatrix} lat \\ long \\ \theta \end{bmatrix}$ where lat and long are latitude and longitude (in degree) and $\theta$ is the current orientation of my vehicle (also in degree). In my Prediction Step I get a reading for current speed...
I am using a miniature car and I want to estimate the position. We can not use GPS modules and most of the tracking systems that I saw, are using IMU senson with the GPS module. In our car we are able to find our exact correct location with image processing but for some parts that dont have enough markings we can not d...
I want to make a quadcopter for my final year project and I am willing to use DC motors as the four rotors of the quadcopter. Can any one guide me about the ratings for proper motor selection for my job.
I have a 4 wheeled differential drive robot, like the Pioneer 3-AT. There are only two motors, one for left wheels and one for right wheels. I want to send velocity commands to the robot, I'm using ROS and the standard commands are: [linear_velocity, angular_velocity]. I need to convert them into left and right velocit...
I'm simulating a sensor in 3D. The sensor should determine ($p, \theta, \phi$) from the origin where $\theta$ is the rotation about z-axis and $\phi$ is the rotation about x-axis. The sensor is given position of a point($x, y, z$). This is what I did p = sqrt(x^2 + y^2 + z^2); theta = acos(z/p); <---- I'm guessi...
I have a quadcopter equipped with PX4FMU board. You may download its datasheet from HERE. I wonder whether it is possible to program the quadcopter to autonomously follow a path like circular motion without any human interference. Are the built-in sensors enough for this task? I also wonder how accurate the built-in GP...
My question is very broad. However I would like a complete description to the very last detail in a way that a foreign exchange student would understand. I want to try my best to master the way the Kalman Filter works. Please be as through as you possibly can, and more.
I am an aerospace engineer (currently in grad school) and I really want to get into (embedded) electronics. But I have this problem: I understand the theory fairly well, I took an edX course in circuits and had no problem. I can build projects from the internet. However, I have a very hard hard time connecting the theo...
I'm implementing Monte-Carlo localization for my robot that is given a map of the enviroment and its starting location and orientation. Mine approach is as follows: Uniformly create 500 particles around the given position Then at each step: motion update all the particles with odometry (my current approach is newX=ol...
As far as I can tell, an ultrasonic rangefinder works by reflecting inaudible soundwaves off of objects and timing their return. But if the object has a flat surface and is angled with respect to the line to the rangefinder, how does it detect that object? Under what circumstances might it give a false distance or ot...
This is actually a very simple question, but I'm lost at the moment. I was using a beaglebone black for a school project. It controls a bunch of motors and actuators,etc. We wrote everything in C++, and made libraries of functions. When a main program calls them, the functions run just fine. Recently we have been told ...
I would like to use a Kuka/abb 6 axis robot and a machine vision system to pick and place a variety of metal drill bits in size ranges from 0.5mm (ascending up 0.5mm per cylinde) to 13mm in metric and then 1/16 of an inch ascending to 9/64 of an inch. The machine would not have to differentiate between the bits, niethe...
I want to make a copy of this machine Fisher Price Soothing Motions™ Glider and I'm wondering what motor to use? Simple DC motor with appropriate gearbox (slow rpm) or stepper motor? Here is another instance of this idea.
I have very limited experience with sensors or robotic components at all, and I hope you will excuse the lack of detail in this Question. I want to set up posts around my yard with electronic noses that detect dog urine. I want to use this information to make a map of my yard from a dogs perspective. Is it possible wi...
I am working on a line follower robot as part of my Microelectronics project, and am confused over what sort of code to use to program the "pic18f" microcontroller I'm using. Can someone give me source code or a layout of the code and what should be in there?
robotics enthusiasts! I'm a member of a team which has to develop a mobile rescue robot to cooperate with firemen (e.g. on earthquake sites). The problem we have is connection of a commander post with the robot. The robot has to enter buildings, so it is desirable that the connection can go through several decimeters o...
I am a beginner in robotics, and I am learning about the Kalman filter. I do not seem to get it, though. I am a mathematician, and so it would be helpful if the Kalman filter could be explained in a mathematical method.
I have a steam radiator at home and it has a valve similar to the picture below. Please note that the valve doesn't have grooves on top to attach things to. I want to build something to turn it on and off depending on the temperature at certain points in the room. I have that taken care of but cannot find a way to att...
I have zero experience with robotics, but I need to build a mobile platform for a streaming camera. The idea is that I'll plug in my Android phone into the pan/tilt unit on my wheeled robot and then drive and look around via WiFi. I have already solved all of the software, interface and controller issues, but I would a...
I'm struggling with the concept of covariance matrix. $$ \Sigma = \begin{bmatrix} \sigma_{xx} & \sigma_{xy} & \sigma_{x \theta} \\ \sigma_{yx} & \sigma_{yy} & \sigma_{y \theta} \\ \sigma_{\theta x} & \sigma_{\theta y} & \sigma_{\theta \theta} \\ \end{bmatrix} $$ Now, my understanding for $\sigma_{xx}$, $\sigma_{yy}$,...
I'm trying to make a quadcopter move laterally at a certain angle. I've been able to find the proper roll and pitch angles for this (that work with a yaw of 0°); how would I adjust these values to compensate for a different yaw?
From each step of my vision code I am able to get around 400 coordinates of where the robot thinks the walls are I want to integrate this into Monte-Carlo observation step. I'm storing the map of the maze as a set of Line segments. What would be a nice way to implement the sensor update, i.e. given the position (x,y) o...
I want to capture two views of same scene. The scene consists of a set of objects kept on a table. From the two views, I wish to calculate homography for image matching. I want to know what is the maximum angle between the two views such that the homography can be accurately calculated. Right now, I am capturing the i...