Spaces:
Running
summarize the text in the frence
2.1. Basis principles
The sequence of events occurring during the most common type of nuclear reaction used for NAA, namely the neutron capture or (n, gamma) reaction, is illustrated in Figure 1. Creation of a compound nucleus forms in an excited state when a neutron interacts with the target nucleus via a non-elastic collision. The excitation energy of the compound nucleus is due to
the binding energy of the neutron with the nucleus. The compound nucleus will almost in‐stantaneously de-excite into a more stable configuration through emission of one or more characteristic prompt gamma rays. In many cases, this new configuration yields a radioac‐tive nucleus which also de-excites (or decays) by emission of one or more characteristic de‐layed gamma rays, but at a much lower rate according to the unique half-life of the radioactive nucleus. Depending upon the particular radioactive species, half-lives can range from fractions of a second to several years.
In principle, therefore, with respect to the time of measurement, NAA falls into two catego‐ries: (1) prompt gamma-ray neutron activation analysis (PGNAA), where measurements take place during irradiation, or (2) delayed gamma-ray neutron activation analysis (DGNAA), where the measurements follow radioactive decay. The latter operational mode is more common; thus, when one mentions NAA it is generally assumed that measurement
of the delayed gamma rays is intended. About 70% of the elements have properties suitable for measurement by NAA.
The PGAA technique is generally performed by using a beam of neutrons extracted through a reactor beam port. Fluxes on samples irradiated in beams are in the order of one million times lower than on samples inside a reactor but detectors can be placed very close to the sample compensating for much of the loss in sensitivity due to flux. The PGAA technique is most appli‐cable to elements with extremely high neutron capture cross-sections (B, Cd, Sm, and Gd); ele‐ments which decay too rapidly to be measured by DGAA; elements that produce only stable isotopes (e.g. light elements); or elements with weak decay gamma-ray intensities. 2D, 3D-analysis of (main) elements distribution in the samples can be performed by PGAA.
DGNAA (sometimes called conventional NAA) is useful for the vast majority of elements that produce radioactive nuclides. The technique is flexible with respect to time such that the sensitivity for a long-lived radionuclide that suffers from interference by a shorter-lived radionuclide can be improved by waiting for the short-lived radionuclide to decay or quite the contrary, the sensitivity for short-lived isotopes can be improved by reducing the time irradiation to minimize the interference of long-lived isotopes. This selectivity is a key advantage of DGNAA over other analytical methods.
In most cases, the radioactive isotopes decay and emit beta particles accompanied by gamma quanta of characteristic energies, and the radiation can be used both to identify and accurately quantify the elements of the sample. Subsequent to irradiation, the samples can be measured instrumentally by a high resolution semiconductor detector, or for better sensitivity, chemical separations can also be applied to reduce interferences. The qualitative characteristics are: the energy of the emitted gamma quanta (Eγ) and the half life of the nuclide (T½). The quantitative characteristic is: the Iγ intensity, which is the number of gamma quanta of energy Eγ measured per unit time.
The n-gamma reaction is the fundamental reaction for neutron activation analysis. For example, consider the following reaction:
58Fe +1 n →59 Fe + Beta-+ gamma rays
58Fe is a stable isotope of iron while 59Fe is a radioactive isotope. The gamma rays emitted during the decay of the 59Fe nucleus have energies of 142.4, 1099.2, and 1291.6 KeV, and these gamma ray energies are characteristic for this nuclide (see figure 2) [2]. The probability of a neutron interacting with a nucleus is a function of the neutron energy. This probability is referred to as the capture cross-section, and each nuclide has its own neutron energy-capture cross-section relationship. For many nuclides, the capture cross-section is greatest for low energy neutrons (referred to as thermal neutrons). Some nuclides have greater capture cross-sections for higher energy neutrons (epithermal neutrons). For routine neutron activation analysis we are generally looking at nuclides that are activated by thermal neutrons.
The most common reaction occurring in NAA is the (n,γ) reaction, but also reactions such as (n,p), (n,α), (n,n′) and (n,2n) are important. The neutron cross section, σ, is a measure for the probability that a reaction will take place, and can be strongly different for different reaction types, elements and energy distributions of the bombarding neutrons. Some nuclei, like 235U are fissionable by neutron capture and the reaction is denoted as (n,f), yielding fission products and fast (highly energetic) neutrons [1].
Neutrons are produced via
• Isotopic neutron sources, like 226Ra(Be), 124Sb(Be), 241Am(Be), 252Cf. The neutrons have different energy distributions with a maximum in the order of 3–4 MeV; the total output is typically 105–107 s -1 GBq-1 or, for 252Cf, 2.2 1012 s-1g-1.
Particle accelerators or neutron generators. The most common types are based on the ac‐
celeration of deuterium ions towards a target containing either deuterium or tritium, re‐
sulting in the reactions 2H(2H,n)3He and 3H(2H,n)4He, respectively. The first reaction, often denoted as (D,D), yields monoenergetic neutrons of 2.5 MeV and typical outputs in the order of 108–1010 s−1; the second reaction (D,T) results in monoenergetic neutrons of 14.7 MeV and outputs of 109–1011 s−1.
• Nuclear research reactors. The neutron energy distribution depends on design of the reactor and its irradiation facilities. An example of an energy distribution in a light water moderated reactor is given in Fig. 2.3 from which it can be seen that the major part of the neutrons has a much lower energy distribution that in isotopic sources and neutron generators. The neutron output of research reactors is often quoted as neutron fluence rate in an irradiation facility and varies, depending on reactor design and reactor power, between 1015 and 1018 m-2 s-1.
Owing to the high neutron flux, experimental nuclear reactors operating in the maximum thermal power region of 100 kW -10 MW with a maximum thermal neutron flux of 1012-1014
neutrons cm-2 s-1 are the most efficient neutron sources for high sensitivity activation analysis induced by epithermal and thermal neutrons. The reason for the high sensitivity is that the cross section of neutron activation is high in the thermal region for the majority of the elements. There is a wide distribution of neutron energy in a reactor and, therefore, interfering reactions must be considered. In order to take these reactions into account, the neutron spectrum in the channels of irradiation should be known exactly. E.g. if thermal neutron irradiations are required, the most thermalized channels should be chosen.
Although there are several types of neutron sources (reactors, accelerators, and radioisotopic neutron emitters) one can use for NAA, nuclear reactors with their high fluxes of neutrons from uranium fission offer the highest available sensitivities for most elements. Different types of reactors and different positions within a reactor can vary considerably with regard to their neutron energy distributions and fluxes due to the materials used to moderate (or reduce the energies of) the primary fission neutrons. This is further elaborated in the title “Derivation of the measurement equation”. In our case, the NAA method is based on the use of neutron flux in several irradiation channels of Es-Salam Research reactor. In 2011, Hamidatou L et Al., reported “Experimental and MCNP calculations of neutron flux parameters in irradiation channel at Es-Salam reactor” the core modelling to calculate neutron
spectra using experimental and MCNP approaches. The Es-Salam reactor was designed for a thermal power output of 15 Mw, with 72 cylindrical cluster fuel elements; each fuel element consists of 12 cylindrical rods of low enriched UO2. In addition the both of fuel throttle tube of the cluster and fuel element tube encloses heavy water as moderator and coolant. The fuel elements are arranged on a heavy water square lattice. The core of the reactor is constituted by a grid containing 72 fuel elements, 12 rods for reactivity control and two experimental channels.
There is also a heavy water in the middle of the core including five experimental channels called inner reflector, In addition, all fuel elements have a reflector at each end called upper and lower reflector. The core is reflected laterally by heavy water maintained in aluminium tank followed by the graphite.
2.2. Neutron activation analysis procedure
In the majority of INAA procedures thermal reactor neutrons are used for the activation:
neutrons in thermal equilibrium with their environment. Sometimes activation with epithermal reactor neutrons (neutrons in the process of slowing down after their formation from fission of 235U) is preferred to enhance the activation of elements with a high ratio of resonance neutron cross section over thermal neutron cross section relatively to the activation of elements with a lower such a ratio. In principle materials can be activated in any physical state, viz. solid, liquid or gaseous. There is no fundamental necessity to convert solid material into a solution prior to activation; INAA is essentially considered to be a non-destructive method although under certain conditions some material damage may occur due to thermal heating, radiolysis and radiation tracks by e.g. fission fragments and α-radiation emitting nuclei. It is essential to have more than two or three qualified full-time member of the staff
with responsibility for the NAA facilities. They should be able to control the counting equipment and have good knowledge of basic principles of the technique. In addition, the facility users and the operators must establish a good channel of communication. Other support staff will be required to maintain and improve the equipment and facility. It seems, therefore, a multi-disciplinary team could run the NAA system well.
The analytical procedure is based on four steps:
Step 1: sample preparation (Figure 3) means in most cases only heating or freeze drying, crushing or pulverization, fractionating or pelletizing, evaporation or pre-concentration, put through a sieve, homogenising, weighing, washing, check of impurities (blank test), encapsulation and sealing irradiation vial, as well as the selection of the best analytical process and the preparation of the standards. The laboratory ambiance is also important for preservation and storage of the samples. Standardization is the basis for good accuracy of analytical tools and often depends on particular technology, facility and personnel. For production of accurate data,
careful attention to all possible errors in preparing single or multi-element standards is important, and standards must be well chosen depending on the nature of the samples.
Step 2: irradiation of samples can be taken from the various types of neutron sources according to need and availability. For the INAA, one pneumatic transfer system installed in the horizontal channel at Es-Salam research reactor for short irradiation of samples (Figure 4). In addition, two vertical channels located in different sites of the heavy water moderator and the graphite reflector have been used for long irradiations. The neutron spectrum parameters at different irradiation channels such as alpha, f, Tn, etc are experimentally determined using cadmium ratio, cadmium cover, bare triple monitor and bi-isotopic methods using HΦgdhal convention and Westcott formalism Table 1 and Table 2. The calibration of the irradiation positions has been carried out to implement the k0-NAA in our laboratory.
Step 3: after the irradiation the measurement is performed after a suitable cooling time (tc).
In NAA, nearly exclusively the (energy of the) gamma radiation is measured because of its higher penetrating power of this type of radiation, and the selectivity that can be obtained from distinct energies of the photons - differently from beta radiation which is a continuous energy distribution. The interaction of gamma- and X-radiation with matter results, among others, in ionization processes and subsequent generation of electrical signals (currents) that can be detected and recorded.
The instrumentation used to measure gamma rays from radioactive samples generally consists of a semiconductor detector, associated electronics, and a computer-based multi-channel analyzer (MCA/computer).
Most NAA labs operate one or more hyper-pure germanium (HPGe) detectors, which operate at liquid nitrogen temperature (77 K). Although HPGe detectors come in many different shapes and sizes, the most common shape is coaxial. These detectors are very useful for measurement of gamma rays with energies in the range from about 60 keV to 3.0 MeV. The two most important characteristics a HPGe detector are its resolution and efficiency. Other characteristics to consider are peak shape, peak-to-Compton ratio, pulse rise time, crystal dimensions or shape, and price. The detector’s resolution is a measure of its ability to separate
closely spaced peaks in the spectrum, and, in general, the resolution is specified in terms of the full width at half maximum (FWHM) of the 122 keV photopeak of 57Co and the 1,332 keV photopeak of 60Co. For most NAA applications, a detector with 0.5 keV resolution or less at 122 keV and 1.8 keV or less at 1,332 keV is sufficient. Detector efficiency for a given detector depends on gamma-ray energy and the sample and detector geometry, i.e. subtended solid angle. Of course, a larger volume detector will have a higher efficiency.
At Es-Salam NAA Lab, four gamma-ray spectrometers of Canberra for which one of them consists of a HPGe detector 35% relative efficiency connected with Genie 2k Inspector and the three other spectrometers are composed of detectors (30, 35 and 45 % relative efficiency)
connected with a three Lynx® Digital Signal Analyser, It is a 32K channel integrated signal analyzer based on advanced digital signal processing (DSP) techniques. All spectrometers operate with Genie™2000 spectroscopy software. A radiation detector therefore consists of an absorbing material in which at least part of the radiation energy is converted into detectable products, and a system for the detection of these products. Figure 5 illustrates Gammaray spectroscopy systems. The detectors are kept at liquid nitrogen temperatures (dewers under cave). The boxes in the left and in the right of the computer are the Lynx Digital Spectrometer Processing.
Step 5: Measurement, evaluation and calculation involve taking the gamma spectra and the calculating trace element concentrations of the sample and preparation of the NAA report.
In this part of work, Peter bode describes clearly in his paper [1] the analysis procedure of gamma-spectrum to the determination of the amount of element in sample. The acquisition of gamma spectrum Fig.6 and Fig.7 via the spectroscopy system Fig. 5 is analyzed to identify the radionuclides produced and their amounts of radioactivity in order to derive the target elements from which they have been produced and their masses in the activated sample.
The spectrum analysis starts with the determination of the location of the (centroids of the) peaks. Secondly, the peaks are fitted to obtain their precise positions and net peak areas. The Analytical protocol adopted in our NAA laboratory is presented in Fig.8.
The positions – often expressed as channel numbers of the memory of a multi-channel pulse height analyzer – can be converted into the energies of the radiation emitted; this is the basis for the identification of the radioactive nuclei. On basis of knowledge of possible nuclear reactions upon neutron activation, the (stable) element composition is derived. The values of
the net peak areas can be used to calculate the amounts of radioactivity of the radionuclides using the full energy photopeak efficiency of the detector.
The amounts (mass) of the elements may then be determined if the neutron fluence rate and cross sections are known. In the practice, however, the masses of the elements are determined from the net peak areas by comparison with the induced radioactivity of the same neutron activation produced radionuclides from known amounts of the element of interest.
The combination of energy of emitted radiation, relative intensities if photons of different energies are emitted and the half life of the radionuclide is unique for each radionuclide, and forms the basis of the qualitative information in NAA. The amount of the radiation is directly proportional to the number of radioactive nuclei produced (and decaying), and thus with the number of nuclei of the stable isotope that underwent the nuclear reaction. It provides the quantitative information in NAA.
The measured in NAA – the quantity intended to be measured – is the total mass of a given element in a test portion of a sample of a given matrix in all physico-chemical states. The quantity ‘subject to measurement’ is the number of disintegrating nuclei of a radionuclide.
The measurement results in the number of counts in a given period of time, from which the disintegration rate and the number of disintegrating nuclei is calculated; the latter number is directly proportional to the number of nuclei of the stable isotope subject to the nuclear reaction, and thus to the number of nuclei of the element, which finally provides information on the mass and amount of substance of that element (see Eq. 16). An example of typical ranges of experimental conditions is given in Table 3 [1].
In practice, our laboratory proceeds in the treatment of spectra and calculation of elemental concentrations of analyzed samples according the approach illustrated in figure 8.