hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.1.2 Test purpose | To verify that when the Network initiates the Packet Measurement Order Procedure, the MS correctly interprets the Packet Measurement Order Message, changes the network control mode and acts accordingly. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.1.3 Method of test | Initial conditions
Parameter
Carrier1
Carrier2
Carrier3
RF Signal Level (dBm)
-70
-80
-50
GPRS_RXLEV_ACCE SS_MIN
-100
-100
-100
NETWORK_CONTRO L_ORDER
NC2
NC2
NC2
C1
30
20
50
C2
30
20
50
System simulator:
3 cells, GPRS supported, PBCCH not present (Carrier 1 & 2 is active. Carrier 3 is off).
Mobile Station:
MS is GPRS ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.2 Network Controlled Cell Reselection/validity of reselection parameters/MS enters standby state | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.2.1 Conformance requirement | A set of measurement reporting parameters (NETWORK_CONTROL_ORDER and NC_REPORTING_PERIOD(s)) is broadcast on PBCCH. The parameters may also be sent individually to an MS on PCCCH or PACCH, in which case it overrides the broadcast parameters. The individual parameters are valid until the RESET command is sent to MS., th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.2.2 Test purpose | To verify that the measurement reporting parameters are valid till the MS enters the standby state.
42.4.4.2.3 Method of test
Initial conditions
Parameter
Carrier1
Carrier2
RF Signal Level (dBm)
-80
-70
GPRS_RXLEV_ACCE SS_MIN
-100
-100
NETWORK_CONTRO L_ORDER
NC0
NC2
C1
20
30
C32
20
30
System simulator:
2 cells (cell A... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.3 Network Control measurement reporting / Idle mode / Returning to Broadcast parameters | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.3.1 Conformance requirement | The procedure for NC measurement report sending shall be initiated by the mobile station at the expiry of the NC measurement report interval timer T3158. At expiry of the timer T3158 the mobile station shall restart the timer T3158, perform the measurements and send the PACKET MEASUREMENT REPORT message containing the ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.3.2 Test Purpose | To verify that individual parameters are valid only until the MS goes to Stand-by State. MS returns to broadcast parameters once it enters the Stand-by State and uses the broadcast parameters if it again goes to ready state. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.3.3 Method of test | Initial conditions
System Simulator:
1 cell, GPRS supported.
Mobile Station:
MS is GPRS attached with a P-TMSI allocated, SPLIT PG CYCLE negotiated
PDP context 2 established.
Specific PICS Statements
-
PIXIT Statements
-
Test procedure
SS assigns a single block downlink TBF to MS and sends PACKET MEASUREMENT ORDER chan... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.4 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.5 Network Control measurement reporting / Idle mode / Reselection due to RA failure | 42.4.4.5.1 Conformance Requirement
Having made M + 1 attempts to send a PACKET CHANNEL REQUEST (respectively EGPRS PACKET CHANNEL REQUEST) message, the mobile station shall stop timer T3186 and start timer T3170. At expiry of timer T3170, the packet access procedure shall be aborted, a random access failure shall be in... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.5.2 Test Purpose | To verify that while in NC2, MS performs autonomous cell reselection when the reselection is triggered by the random access failure. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.4.5.3 Method of test | Initial conditions
System Simulator:
2 cell, GPRS supported.
Parameter
Carrier1
Carrier2
RF Signal Level (dBm)
-60
-70
NETWORK_CONTROL_ORDER
NC2
NC2
NC_REPORTING_PERIOD_I
Default
Default
Mobile Station:
MS is GPRS attached with a P-TMSI allocated, SPLIT PG CYCLE negotiated. Ready timer is set to 5 min.
PDP context 2 es... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5 Network Assisted Cell Change | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.1 Network Assisted Cell Change / Expiry of T3206 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.1.1 Conformance requirements | [3GPP TS 44.060, 8.1.3]
If CCN is enabled (see subclause 5.5.1.1a, 3GPP TS 44.160 subclause 5.4.1.3), the mobile station shall behave as in network control mode NC0 or NC1 up to the point when a new cell has been chosen. It shall then check the CCN_SUPPORTED parameter, if available, that was last received for that cell... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.1.2 Test purpose | To verify that the MS leaves the CCN mode and continues cell reselection in NC0 mode when T3206 expires. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.1.3 Method of test | Initial conditions
System Simulator:
2 cells, GPRS supported, CCN Active, PCCCH not present.
GPRS ready timer T3314 = infinity
Cell A: RLA_C = -50 dBm
Cell B: RLA_C = -60 dBm
Mobile Station:
MS is in Packet Idle mode, GPRS attached with support of GERAN Feature Package 1 indicated in MS Radio Access Capabilities, and P... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.2 Network Assisted Cell Change / No Packet Neighbouring Cell Data and Packet Cell Change Continue | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.2.1 Conformance requirements | [3GPP TS 44.060, 8.1.1]
The mobile station shall transmit RLC/MAC blocks with the following priority:
• RLC/MAC control blocks containing a Packet Cell Change Notification message;
• Other RLC/MAC control blocks, except Packet Uplink Dummy Control Blocks;
• RLC data blocks;
• RLC/MAC control blocks containing Packet Up... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.2.2 Test purpose | 1) To verify that MS sends a PACKET CELL CHANGE NOTIFICATION when it enters CCN mode.
2) To verify that MS leaves CCN mode and continues cell reselection in NC0 mode when a PACKET CELL CHANGE CONTINUE is received when no PACKET NEIGHBOUR CELL DATA has been received. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.2.3 Method of test | Initial conditions
System Simulator:
2 cells, GPRS supported, CCN Active, PCCCH not present.
GPRS ready timer T3314 = infinity
Cell A: RLA_C = -50 dBm
Cell B: RLA_C = -60 dBm
Mobile Station:
MS is in Packet Idle mode, GPRS attached with support of GERAN Feature Package 1 indicated in MS Radio Access Capabilities, and P... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.3 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.4 Network Assisted Cell Change / Packet Neighbour Cell Data and Packet Cell Change Order | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.4.1 Conformance requirements | [3GPP TS 44.060, 5.5.1.4.3]
A mobile station supporting the Network Assisted Cell Change procedures shall implement the request for acquisition of system information (see clause 5.5.1.1a).
The PACKET PSI STATUS (respectively PACKET SI STATUS) message shall indicate the present status of PSI (respectively SI) messages s... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.4.2 Test purpose | 1. To verify that the MS applies CCN when CCN is indicated in SI13 of the serving cell by sending a PACKET CELL CHANGE NOFITICATION when deciding to make a cell reselection.
2. To verify that MS leaves CCN mode when it receives a PACKET CELL CHANGE ORDER and follows the procedures as specified in the PACKET CELL CHANGE... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.4.3 Method of test | Initial conditions
System Simulator:
3 cells, GPRS supported, CCN Active in SI13, PCCCH not present.
GPRS ready timer T3314 = infinity
Cell A: The indication of Cell C is removed in SI2. RLA_C = -50 dBm
Cell B: Supports PACKET SI STATUS. No System Information is broadcast on the BCCH, except SI3. This is only made to m... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.5 Network Assisted Cell Change / Expiry of T3208 and T3210 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.5.2 Conformance requirements | [3GPP TS 44.060, 8.8.3]
After receiving a PACKET CELL CHANGE NOTIFICATION message from the mobile station the network can behave in different ways as described below.
5) No network response
When timer T3210 expires, the mobile station shall retransmit once the PACKET CELL CHANGE NOTIFICATION message at the first possib... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.5.2 Test purpose | 1. To verify that the MS retransmits the PACKET CELL CHANGE NOTIFICATION when T3210 expires 300 ms after no reception of any PACKET NEIGHBOUR CELL DATA, PACKET CELL CHANGE CONTINUE, PACKET MEASURMENT ORDER or PACKET CELL CHANGE ORDER.
2. To verify that MS leaves CCN mode when T3208 expires and continues cell reselectio... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.5.3 Method of test | Initial conditions
System Simulator:
2 cells, GPRS supported, CCN Active in SI13, PCCCH not present.
Cell A: RLA_C = -50 dBm
Cell B: RLA_C = -60 dBm
Mobile Station:
MS is in Packet Idle mode, GPRS attached with support of GERAN Feature Package 1 indicated in MS Radio Access Capabilities, and PDP context 2 established.
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.6 Network Assisted Cell Change / Entering packet idle mode | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.6.1 Conformance requirements | [3GPP TS 44.060, 8.8.3]
The CCN mode is only valid in Packet Transfer Mode. If the mobile station is in CCN mode when entering packet idle mode, the mobile station shall stop the timers T3206 and T3208, stop timer T3210 if still running, leave CCN mode and continue the cell reselection procedure according to the NC0/NC... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.6.2 Test purpose | To verify that the MS continues according to the normal packet idle mode cell reselection procedures when leaving CCN mode and entering packet idle mode. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.6.3 Method of test | Initial conditions
System Simulator:
2 cells, GPRS supported, CCN Active in SI13, PCCCH not present.
GPRS ready timer T3314 = infinity
T3192 = 0 ms
Mobile Station:
MS is in Packet Idle mode, GPRS attached with support of GERAN Feature Package 1 indicated in MS Radio Access Capabilities, and PDP context 2 established.
C... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.7 Network Assisted Cell Change / CCN not supported towards target cell | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.7.1 Conformance requirements | The SI2quater message may also contain information, the CCN Support description, to be used when CCN is enabled in the serving cell, see 3GPP TS 44.060. This CCN Support description is associated with the Neighbour Cell list (see 3.4.1.2.1.3) having the same BA_IND value and 3G_BA_IND value. Each CCN_SUPPORTED bit of t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.7.2 Test purpose | To verify that the MS does not apply CCN on a target cell when the CCN support description not is set for that cell. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.7.3 Method of test | Initial conditions
System Simulator:
2 cells, GPRS supported, PCCCH not present.
Cell A: CCN Active. SI3 indicates SI2quater broad cast on BCCH norm. SI2quater contains a CCN Support Description indicating that CCN not is supported towards Cell B. RLA_C = -50 dBm
Cell B: CCN Active. RLA_C = -60 dBm
Mobile Station:
MS i... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.8 Network Assisted Cell Change / NC mode change | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.8.1 Conformance requirements | [3GPP TS 44.060, 8.8.3 & 4)]
The network orders the mobile station into NC2 mode.
A mobile station may in response to a PACKET CELL CHANGE NOTIFICATION message sent to the network receive a PACKET MEASUREMENT ORDER message indicating NC2 mode. When the mobile station receives the NC2 order it shall leave CCN mode, stop... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.8.2 Test purpose | To verify that the MS leaves the CCN mode and enters NC2 mode on receipt of Packet Measurement Order and the NC2 parameters. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.8.3 Method of test | Initial conditions
System Simulator:
2 cells, GPRS supported, CCN Active, RXLEV_ACCESS_MIN = -90dBm.
GPRS ready timer T3314 = infinity
Cell A: RLA_C = -50 dBm
Cell B: RLA_C = -60 dBm
Mobile Station:
MS is in Packet Idle mode, GPRS attached with support of GERAN Feature Package 1 indicated in MS Radio Access Capabilitie... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.9 Network Assisted Cell Change / NC mode change / Packet Neighbour Cell Data | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.9.1 Conformance requirements | [3GPP TS 44.060, 8.8.3 & 4)]
The network orders the mobile station into NC2 mode.
A mobile station may in response to a PACKET CELL CHANGE NOTIFICATION message sent to the network receive a PACKET MEASUREMENT ORDER message indicating NC2 mode. When the mobile station receives the NC2 order it shall leave CCN mode, stop... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.9.2 References | 3GPP TS 44.060, subclause 5.5.1.4.3 and 8.8.3 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.9.3 Test purpose | 1. To verify that MS leaves CCN mode when it receives a PACKET MEASUREMENT ORDER activating NC2 and follows the NC2 procedures.
2. To verify that MS uses the System Information received in PACKET NEIGHBOUR CELL DATA when accessing the new cell.
3. To verify that MS requests remaining System Information messages when ha... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.9.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.9.4.1 Initial conditions | System Simulator:
3 cells, GPRS supported, CCN Active in SI13, PCCCH not present.
GPRS ready timer T3314 = infinity
Cell A: The indication of Cell C is removed in SI2. RLA_C = -50 dBm
Cell B: Supports PACKET SI STATUS. No System Information is broadcast on the BCCH, except SI3. This is only made to make it possible to ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.9.4.2 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.5.9.4.3 Test procedure | The MS is triggered to initiate packet uplink transfer. SS assigns resources to the MS and the MS starts to send uplink data that the SS acknowledges. During the uplink transfer, the signal strength of cell A is lowered to – 80 dBm. The MS enters CCN mode and sends PACKET CELL CHANGE NOTIFICATION. The MS then continues... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6 Packet Enhanced Measurement Report (PEMR) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.1 Network Control PEMR – Activation with SI Messages | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.1.1 Conformance requirement | 1 The behaviour of the mobile station is controlled by the parameter NETWORK_CONTROL_ORDER broadcast in the PSI5 message on PBCCH, in the SI13 and SI2quater messages on the BCCH and in the PSI13 message on PACCH.
When in mode NC1 or NC2, the mobile station shall perform the NC measurements as defined in 3GPP TS 05.08. ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.1.2 Test purpose | To verify that the MS sends PEMR following the report type and according to the indicated reporting periods covering GSM neighbour list specified in SI2quater. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.1.3 Method of test | Initial conditions
Transmitter
RF Signal
NCC
BCC
Cell Identity
Level (dBm)
Serving, S1
‑60
1
3
0001H
Neighbour, N1
‑70
1
5
0002H
The ARFCN of the serving and neighbouring cell is selected from the default defined in section 40.
System simulator:
2 GPRS cells configured as GPRS cells with SI2 quater giving all adjacent ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.2 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.3 Network Control PEMR – Packet Measurement Order | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.3.1 Conformance requirement | 1 The behaviour of the mobile station is controlled by the parameter NETWORK_CONTROL_ORDER broadcast in the PSI5 message on PBCCH, in the SI13 and SI2quater messages on the BCCH and in the PSI13 message on PACCH.
When in mode NC1 or NC2, the mobile station shall perform the NC measurements as defined in 3GPP TS 05.08. ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 2 In packet idle mode, the reporting period is NC_REPORTING_PERIOD_I rounded off to the nearest smaller integer multiple of DRX period if NC_REPORTING PERIOD_I is greater than DRX period, else, the reporting period is DRX period | Reference:
3GPP TS 04.60 / 3GPP TS 44.060 subclause 5.6.1
3GPP TS 05.08 / 3GPP TS 45.008 subclause 10.1.4.1 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.3.2 Test purpose | To verify that the MS sends PEMR following the report type and according to the indicated reporting period specified in Packet Measurement Order.
42.4.6.3.3 Method of test
Initial conditions
Transmitter
RF Signal
NCC
BCC
Cell Identity
Level (dBm)
Serving, S1
‑60
1
3
0001H
Neighbour, N1
‑70
1
5
0002H
The ARFCN of the s... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.4 Network Control PEMR – Uplink Data Transfer | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.4.1 Conformance requirement | The behaviour of the mobile station is controlled by the parameter NETWORK_CONTROL_ORDER broadcast in the PSI5 message on PBCCH, in the SI13 and SI2quater messages on the BCCH and in the PSI13 message on PACCH. Alternatively, the network may send the NETWORK_CONTROL_ORDER parameters in a PACKET MEASUREMENT ORDER or in ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.4.2 Test Purpose | To verify that the MS sends PEMR during uplink packet transfer according to the indicated reporting type and reporting periods specified in SI2quater.
To verify that the MS sends PEMR during uplink packet transfer according to the indicated reporting type and reporting period specified in Packet Measurement Order.
Refe... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.4.3 Method of test | Initial conditions
Transmitter
RF Signal
NCC
BCC
Cell Identity
Level (dBm)
Serving, S1
‑60
1
3
0001H
Neighbour, N1
‑70
1
5
0002H
The ARFCN of the serving and neighbouring cell is selected from the default defined in section 40.
System simulator:
2 cells configured as GPRS cells with SI2 quater giving adjacent cell conf... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.5 Network Control PEMR – Downlink Data Transfer | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.5.1 Conformance requirement | The behaviour of the mobile station is controlled by the parameter NETWORK_CONTROL_ORDER broadcast in the PSI5 message on PBCCH, in the SI13 and SI2quater messages on the BCCH and in the PSI13 message on PACCH. Alternatively, the network may send the NETWORK_CONTROL_ORDER parameters in a PACKET MEASUREMENT ORDER or in ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.5.2 Test Purpose | To verify that the MS sends PEMR during downlink packet transfer according to the indicated reporting type and reporting periods specified in SI2 quater.
To verify that the MS sends PEMR during downlink packet transfer according to the indicated reporting type and reporting period specified in Packet Measurement Order. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.5.3 Method of test | Initial conditions
Transmitter
RF Signal
NCC
BCC
Cell Identity
Level (dBm)
Serving, S1
‑60
1
3
0001H
Neighbour, N1
‑70
1
5
0002H
The ARFCN of the serving and neighbouring cell is selected from the default defined in section 40.
System simulator:
2 cells configured as GPRS cells with SI2 quater giving adjacent cell conf... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.6 Network Control PEMR / Packet Cell Change Order | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.6.1 Conformance requirement | For (NC) measurement reporting, the Mobile Station shall use PACKET ENHANCED MEASUREMENT REPORT messages instead of PACKET MEASUREMENT REPORT messages if that is indicated by the parameter REPORT_TYPE and if at least one BSIC is allocated to each frequency in the BA(GPRS) list.
Reference:
3GPP TS 04.60 / 3GPP TS 44.060... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.6.2 Test purpose | To verify that the MS sends PEMR following the report type specified in Packet Cell Change Order.
42.4.6.6.3 Method of test
Initial conditions
Transmitter
RF Signal Level (dBm)
NCC
BCC
Cell Identity
Serving, S1
‑60
1
3
0001H
Neighbour, N1
‑70
1
5
0002H
The ARFCN of the serving and neighbouring cell is selected from th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.6.7 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7 Inter-RAT (GPRS to UTRAN) Cell Change Order | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.1 Inter-RAT Cell Change Order (Known Cell) – Uplink Data Transfer | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.1.1 Conformance requirement | For a multi-RAT mobile station, the PACKET CELL CHANGE ORDER message may contain information on a 3G target cell, together with the IMMEDIATE_REL parameter; in the case of UTRAN establishment of UTRAN channel(s) and subsequent measurement reporting are defined in 3GPP TS 25.331.
Upon receipt of the PACKET CELL CHANGE O... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.1.2 Test Purpose | To verify the when NC2 is commanded, the MS sends PACKET ENHANCED MEASUREMENT REPORT messages, in which both the serving and non-serving cells are reported.
To verify that when the cell change order procedure is started by sending a PACKET CELL CHANGE ORDER message with the IMMEDIATE_REL value set to 1, the MS shall ab... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.1.3 Method of test | Initial conditions
System simulator:
2 cells - Cell A is GPRS, Cell B is UTRAN (activated at power ON)
3GPP TS 34.108, subclause 6.1 shall be referenced for default parameters of Cell 2.
3GPP TS 34.123-3, subclause 8.3.2 shall be referenced for configuring channels on Cell 2.
Mobile Station:
MS is in Packet Idle mode a... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.2 Inter-RAT Cell Change Order (Unknown Cell) – Uplink Data Transfer | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.2.1 Conformance requirement | For a multi-RAT mobile station, the PACKET CELL CHANGE ORDER message may contain information on a 3G target cell, together with the IMMEDIATE_REL parameter; in the case of UTRAN establishment of UTRAN channel(s) and subsequent measurement reporting are defined in 3GPP TS 25.331.
Upon receipt of the PACKET CELL CHANGE O... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.2.2 Test Purpose | To verify that when the cell change order procedure is started by sending a PACKET CELL CHANGE ORDER message with the IMMEDIATE_REL value set to 1, the MS shall abort any TBF in progress and stop transmitting.
To verify that the MS switches to the commanded UTRAN cell.
Reference
3GPP TS 04.60, subclause 8.4.
3GPP TS 25... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.2.3 Method of test | Initial conditions
System simulator:
2 cells - Cell A is GPRS (NC2), Cell B is UTRAN (activated at power ON)
3GPP TS 34.108, subclause 6.1 shall be referenced for default parameters of Cell 2.
3GPP TS 34.123-3, subclause 8.3.2 shall be referenced for configuring channels on Cell 2.
Mobile Station:
MS is in Packet Idle ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.3 Inter-RAT Cell Change Order (Known Cell) – Downlink Data Transfer | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.3.1 Conformance requirement | For a multi-RAT mobile station, the PACKET CELL CHANGE ORDER message may contain information on a 3G target cell, together with the IMMEDIATE_REL parameter; in the case of UTRAN establishment of UTRAN channel(s) and subsequent measurement reporting are defined in 3GPP TS 25.331.
Upon receipt of the PACKET CELL CHANGE O... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.3.2 Test Purpose | To verify that when the cell change order procedure is started when the MS receives PACKET CELL CHANGE ORDER message with the IMMEDIATE_REL value set to 1.
To verify that the MS switches to the commanded UTRAN cell.
Reference
3GPP TS 04.60, subclause 8.4.
3GPP TS 25.331 subclause 8.3.10 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.3.3 Method of test | Initial conditions
System simulator:
2 cells - Cell A is GPRS, Cell B is UTRAN (activated at power ON)
3GPP TS 34.108, subclause 6.1 shall be referenced for default parameters of Cell 2.
3GPP TS 34.123-3, subclause 8.3.2 shall be referenced for configuring channels on Cell 2.
Mobile Station:
MS is in Packet Idle mode ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.4 Inter-RAT Cell Change Order (Known Cell) – Simultaneous uplink and downlink transfer | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.4.1 Conformance requirement | For a multi-RAT mobile station, the PACKET CELL CHANGE ORDER message may contain information on a 3G target cell, together with the IMMEDIATE_REL parameter; in the case of UTRAN establishment of UTRAN channel(s) and subsequent measurement reporting are defined in 3GPP TS 25.331.
Upon receipt of the PACKET CELL CHANGE O... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.4.2 Test Purpose | To verify that when the cell change order procedure is started by sending a PACKET CELL CHANGE ORDER message with the IMMEDIATE_REL value set to 1, the MS shall abort any TBF in progress and stop transmitting.
To verify that the MS switches to the commanded UTRAN cell.
Reference
3GPP TS 04.60, subclause 8.4.
3GPP TS 25... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.4.3 Method of test | Initial conditions
System simulator:
2 cells - Cell A is GPRS, Cell B is UTRAN (activated at power ON)
3GPP TS 34.108, subclause 6.1 shall be referenced for default parameters of Cell 2.
3GPP TS 34.123-3, subclause 8.3.2 shall be referenced for configuring channels on Cell 2.
Mobile Station:
MS is in Packet Idle mode ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.5 Inter-RAT (GPRS to UTRAN) Cell Change Order (Known cell) / Failure | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.5.1 Inter-RAT (GPRS to UTRAN) Cell Change Order (Known cell) / Failure / Uplink transfer / T3174 expiry | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.5.1.1 Conformance requirement | In the following cases, the mobile station shall determine that the network controlled cell reselection procedure has failed:
- The PACKET CELL CHANGE ORDER message commands the mobile station to a frequency in a frequency band not supported by the mobile station. Cause: “frequency not implemented”.
- The PACKET CELL C... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.5.1.2 Test Purpose | To verify that an MS in uplink packet transfer mode when commanded by a PACKET CELL CHANGE ORDER, reports a PACKET CELL CHANGE FAILURE on the old GPRS cell due to the expiry of T3174 before receiving response to RRC CONNECTION REQUEST on target UTRAN cell. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.5.1.3 Method of test | Initial conditions
System Simulator:
- 2 cells, Cell A, GPRS Supported without PBCCH, NC2.
- Cell B is a UTRAN cell. UTRAN cell is the better cell of the two cells. It is activated after MS is GPRS attached to Cell A. 3GPP TS 34.108, subclause 6.1 shall be referenced for default parameters of Cell B except that T300 an... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.5.2.1 Conformance requirement | In the following cases, the mobile station shall determine that the network controlled cell reselection procedure has failed:
- The PACKET CELL CHANGE ORDER message commands the mobile station to a frequency in a frequency band not supported by the mobile station. Cause: “frequency not implemented”.
- The PACKET CELL C... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.5.2.2 Test Purpose | To verify that an MS in downlink packet transfer mode when commanded by a PACKET CELL CHANGE ORDER, reports PACKET CELL CHANGE FAILURE on the old GPRS cell if an RRC CONNECTION REJECT with Inter-RAT info set to GSM is received on the target UTRAN cell. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.7.5.2.3 Method of test | Initial conditions
System Simulator:
- 2 cells, Cell A, GPRS Supported without PBCCH, NC2. Cell B is a UTRAN cell. Cell Selection conditions favour Cell A. 3G Neighbour Cell Description of Cell A refers to UTRAN Cell B. XXX_MUTIRAT_REPORTING is set to 1. REPORT_TYPE is set to indicate the usage of Packet Enhanced Measu... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8 NC2 Procedures | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1 NC2 and DRX |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.