hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.1 NC2 and DRX / NC_NON_DRX_PERIOD / Respect of NC2 non-DRX mode period | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.1.1 Conformance requirement | There are four cases when the mobile station shall enter a non-DRX mode period.
1) At the transition from the packet transfer mode to the packet idle mode, the mobile station shall enter the Transfer non-DRX mode period.
2) At the transition from the dual transfer mode to the dedicated mode or packet idle mode, the mob... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.1.2 Test Purpose | To verify that an MS in Idle mode enters and remains in the non-drx mode only for the duration of NC2 non-DRX mode period which is equal to NC_NON_DRX_PERIOD parameter, when it sends a NC measurement report
Reference
3GPP TS 44.060, sub-clause 5.5.1.5. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.1.3 Method of test | Initial conditions
System Simulator:
1 cell, GPRS supported.
Mobile Station:
MS is in Packet Idle mode and GPRS attached.
Test PDP context 2 established.
Specific PICS Statements
-
PIXIT Statements
-
Test procedure
SS sends a PACKET MEASUREMENT ORDER message to MS. NETWORK_CONTROL_ORDER is commanded to be NC2. NC_NON_D... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.2 NC2 and DRX / NC_NON_DRX_PERIOD / NC2 non-DRX mode period ordered in Packet Cell Change Order | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.2.1 Conformance requirement | A mobile station operating in NC2 mode shall enter the NC2 non-DRX mode period when it sends an NC measurement report. The duration of this period is defined by the NC_NON_DRX_PERIOD parameter.
The non-DRX mode periods have effect only in packet idle mode. In packet idle mode, the mobile station shall be in non-DRX mod... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.2.2 Test Purpose | To verify that when an MS selects a new cell as ordered using a PACKET CELL CHANGE ORDER message, the MS takes into consideration and respects the NC_NON_DRX_PERIOD parameter sent in a PACKET CELL CHANGE ORDER message in the new cell. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.2.3 Method of test | Initial conditions
System Simulator:
2 cells, GPRS supported.
Mobile Station:
MS is GPRS attached in Cell-A and is in Packet Idle mode. Ready Timer set to 5 min.
Test PDP context 2 established.
Specific PICS Statements
-
PIXIT Statements
-
Test procedure
SS sends a PACKET MEASUREMENT ORDER message to MS ordering the MS... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.3 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.4 NC2 and DRX / NC_NON_DRX_PERIOD / NC2 non-DRX mode period broadcast in SI2Quater | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.4.1 Conformance requirement | A mobile station operating in NC2 mode shall enter the NC2 non-DRX mode period when it sends an NC measurement report. The duration of this period is defined by the NC_NON_DRX_PERIOD parameter.
The non-DRX mode periods have effect only in packet idle mode. In packet idle mode, the mobile station shall be in non-DRX mod... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.4.2 Test Purpose | To verify that when an MS selects a new cell and if no parameters have been brought from the old cell, the MS uses the broadcast measurement parameter NC_NON_DRX_PERIOD from SI2quater if PBCCH is not allocated in the new cell. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.4.3 Method of test | Initial conditions
System Simulator:
2 cells, GPRS supported
SI2quater transmitted (Rest Octet as described in the Specific Message Contents).
Mobile Station:
MS is GPRS attached in Cell-A and is in Packet Idle mode. Ready Timer set to 5 min.
Test PDP context 2 established.
Specific PICS Statements
-
PIXIT Statements
-... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.5 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.6 NC2 and DRX / NC_NON_DRX_PERIOD / NC2 non-DRX mode period / PBCCH absent / Default Value | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.6.1 Conformance requirement | A mobile station operating in NC2 mode shall enter the NC2 non-DRX mode period when it sends an NC measurement report. The duration of this period is defined by the NC_NON_DRX_PERIOD parameter.
The non-DRX mode periods have effect only in packet idle mode. In packet idle mode, the mobile station shall be in non-DRX mod... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.6.2 Test Purpose | To verify that when an MS selects a new cell and if no parameters have been brought from the old cell, the MS uses the default value of NC_NON_DRX_PERIOD parameter if NC Measurement Parameters are not included in the SI2quater broadcast in the new cell. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.1.6.3 Method of test | Initial conditions
System Simulator:
2 cells, GPRS supported
SI2quater transmitted (Rest Octet as described in the Specific Message Contents).
Mobile Station:
MS is GPRS attached in Cell-A and is in Packet Idle mode. Ready timer set to 5 min.
Test PDP context 2 established.
Specific PICS Statements
-
PIXIT Statements
-... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2 User Data vs Measurement Report Sending / Conflict situation | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2.1 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2.2 User Data vs Measurement Report Sending / Conflict situation / Expiry of T3192 and T3158 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2.2.1 Conformance requirement | The mobile station shall apply to the timer T3158 either the NC_REPORTING_PERIOD_I when in packet idle mode or the NC_REPORTING_PERIOD_T when in packet transfer mode.
On expiry of timer T3158, the mobile station shall restart timer T3158 with the indicated reporting period, perform the measurements and send either the ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2.2.2 Test Purpose | To verify that if T3158 expires before the MS leaves Downlink Packet Transfer mode, the MS waits till T3192 expires before it initiate a Packet Access procedure to send PACKET MEASUREMENT REPORT message.
Reference
3GPP TS 04.60, sub-clauses 5.6.1, 9.3.2.6 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2.2.3 Method of test | Initial conditions
System Simulator:
1 cell, GPRS supported.
T3192 set to 1500 msec in GPRS_CELL_OPTIONS
Mobile Station:
MS is GPRS attached and is in Packet Idle mode. Ready Timer set to 5 min.
Test PDP context 2 established.
Specific PICS Statements
-
PIXIT Statements
-
Test procedure
SS establishes a downlink TBF.
W... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2.3 User Data vs Measurement Report Sending / Conflict situation / Expiry of T3182 and T3158 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2.3.1 Conformance requirement | The mobile station shall apply to the timer T3158 either the NC_REPORTING_PERIOD_I when in packet idle mode or the NC_REPORTING_PERIOD_T when in packet transfer mode.
On expiry of timer T3158, the mobile station shall restart timer T3158 with the indicated reporting period, perform the measurements and send either the ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2.3.2 Test Purpose | To verify that if T3158 expires before the MS leaves Uplink Packet Transfer mode and after MS has started T3182
1 the MS will send a PACKET MEASUREMENT REPORT to the SS if uplink resource is allocated before the expiry of T3182.
2 the MS will initiate a Access procedure after T3182 is stopped, if no uplink resource is ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2.3.3 Method of test | Initial conditions
System Simulator:
1 cell, GPRS supported.
Mobile Station:
MS is GPRS attached and is in Packet Idle mode. Ready Timer set to 5 min.
Test PDP context2 established.
Specific PICS Statements
-
PIXIT Statements
-
Test procedure
An uplink TBF is established.
While the TBF is active SS sends a PACKET MEASU... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2.4 User Data vs Measurement Report Sending / Conflict situation / Random Access procedure for PMR sending and User Data transmission | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2.4.1 Conformance requirement | The behaviour of the mobile station is controlled by the parameter NETWORK_CONTROL_ORDER broadcast in the PSI5 message on PBCCH, in the SI13 and SI2quater messages on the BCCH and in the PSI13 message on PACCH. Alternatively, the network may send the NETWORK_CONTROL_ORDER parameters in a PACKET MEASUREMENT ORDER or in ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2.4.2 Test Purpose | To verify that if the MS is triggered to send user data while random access procedure is ongoing to send a PACKET MEASUREMENT REPORT message, the MS will continue the random access procedure, send the PACKET MEASUREMENT REPORT message, will return to Idle mode and then will initiate a random access procedure to send u... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.2.4.3 Method of test | Initial conditions
System Simulator:
1 cell, GPRS supported, PCCCH absent.
CCCH combined with SDCCH. Max Retrans = 7, TX-INTEGER = 32
SI2quater present
SI2quater transmitted (Rest Octets as described in the Specific Message Contents)
Mobile Station:
MS is GPRS attached and is in Packet Idle mode.
Test PDP context3 esta... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3 Network Control measurement reporting and Dedicated connection | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.1 Network Control measurement reporting / Dedicated connection / Timer Ready expiry | 42.4.8.3.1.1 Conformance requirement |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.1.1.1 Conformance requirement for R97 and R98 MS | When the mobile station leaves the MM Ready state, the timer T3158 shall be stopped and no more measurement reports shall be sent to the network.
Reference
3GPP TS 04.60, subclauses 5.6.1 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.1.1.2 Conformance requirement for R99 and later MS | The parameter values NC1 and NC2 only apply in Ready state. In Standby state, the MS shall always use normal MS control independent of the ordered NC mode.
A set of measurement reporting parameters (NETWORK_CONTROL_ORDER and NC_REPORTING_PERIOD(s)) is broadcast on PBCCH. The parameters may also be sent individually to ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.1.2 Test Purpose | To verify that some R97 or R98 MS involved in NC measurement reporting, stops its reporting if the Ready Timer expires within a dedicated connection.
For some R97 or R98 MS and for R99 or later MS, the NC measurement reporting is stopped when entering a dedicated connection. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.1.3 Method of test | Initial conditions
System Simulator:
1 cell, GPRS supported. PBCCH not supported. Default Ready Timer (44s)
Mobile Station:
The MS is in packet idle mode, with a TMSI, P-TMSI allocated
Specific PICS Statements
- Release of GPRS Supported (TSPC_MS_GPRS_RELEASE)
- Support of Immediate Connect (TSPC_AddInfo_ImmConn)
PIXIT... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.2 Network Control measurement reporting / Dedicated connection / Different NC parameters / No T3158 expiry | 42.4.8.3.2.1 Conformance requirement
When in mode NC1 or NC2, the mobile station shall perform the NC measurements as defined in 3GPP TS 05.08. The reporting periods are indicated in the NC_REPORTING_PERIOD_I and NC_REPORTING_PERIOD_T field of the PSI5, the SI2quater, the PACKET CELL CHANGE ORDER or the PACKET MEASUREM... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.2.1.1 Conformance requirement specific for R99 or later MS | A set of measurement reporting parameters (NETWORK_CONTROL_ORDER and NC_REPORTING_PERIOD(s)) is broadcast on PBCCH. The parameters may also be sent individually to an MS on PCCCH or PACCH, in which case it overrides the broadcast parameters. The individual parameters are valid until the RESET command is sent to the MS ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.2.2 Test Purpose | To verify that a MS involved in NC measurement reporting on a NC2 cell, continue its measurement reporting after a dedicated call, with the same NC parameters for some R97 or R98 MS, and with the broadcasted parameters for other R97 or R98 MS and for R99 and later MS. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.2.3 Method of test | Initial conditions
System Simulator:
1 cell, GPRS supported, NC2, Ready Timer set to 5 minutes
Mobile Station:
The MS is in packet idle mode, with a TMSI, P-TMSI allocated
Specific PICS Statements
- Release of GPRS Supported (TSPC_MS_GPRS_RELEASE)
- Support of Immediate Connect (TSPC_AddInfo_ImmConn)
PIXIT Statements
-... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.3 Network Control measurement reporting / Dedicated connection / Handover / No T3158 expiry | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.3.1 Conformance requirement | The behaviour of the mobile station is controlled by the parameter NETWORK_CONTROL_ORDER broadcast in the PSI5 message on PBCCH, in the SI13 message on the BCCH and in the PSI13 message on PACCH. Alternatively, the network may send the NETWORK_CONTROL_ORDER parameters in a PACKET MEASUREMENT ORDER or in a PACKET CELL C... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.3.1.1 Conformance requirement specific for R99 or later MS | A set of measurement reporting parameters (NETWORK_CONTROL_ORDER and NC_REPORTING_PERIOD(s)) is broadcast on PBCCH. The parameters may also be sent individually to an MS on PCCCH or PACCH, in which case it overrides the broadcast parameters. The individual parameters are valid until the RESET command is sent to the MS ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.3.2 Test Purpose | To verify that a MS involved in NC measurement reporting and making a handover to a new NC2 cell, uses the broadcasted NC reporting parameters of its new serving cell for its NC measurement reporting. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.3.3 Method of test | Initial conditions
System Simulator:
2 cells (cell A and cell B), GPRS supported, NC2, Ready Timer set to 5 minutes
Mobile Station:
The MS is in packet idle mode, with a TMSI, P-TMSI allocated
Specific PICS Statements
- Release of GPRS Supported (TSPC_MS_GPRS_RELEASE)
- Support of Immediate Connect (TSPC_AddInfo_ImmCon... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.4 Network Control measurement reporting / Dedicated connection / Different NC parameters / T3158 expiry | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.4.1 Conformance requirement | When in mode NC1 or NC2, the mobile station shall perform the NC measurements as defined in 3GPP TS 05.08. The reporting periods are indicated in the NC_REPORTING_PERIOD_I and NC_REPORTING_PERIOD_T field of the PSI5, the SI2quater, the PACKET CELL CHANGE ORDER or the PACKET MEASUREMENT ORDER message. If NC_NON_DRX_PERI... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.4.1.1 Conformance requirement specific for R99 or later MS | A set of measurement reporting parameters (NETWORK_CONTROL_ORDER and NC_REPORTING_PERIOD(s)) is broadcast on PBCCH. The parameters may also be sent individually to an MS on PCCCH or PACCH, in which case it overrides the broadcast parameters. The individual parameters are valid until the RESET command is sent to the MS ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.4.2 Test Purpose | To verify that some R97 or R98 MS involved in NC measurement reporting, sends only its latest PACKET MEASUREMENT REPORT when many reporting periods had expired during a CS call on the same cell.
To verify that some other R97or R98 MS andR99 and later releases MS stop their measurement reporting with the dedicated call ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.4.3 Method of test | Initial conditions
System Simulator:
2 cells, GPRS supported, NC0, Ready Timer set to 5 minutes
Mobile Station:
The MS is in packet idle mode, with a TMSI, P-TMSI allocated
Specific PICS Statements
- Release of GPRS Supported (TSPC_MS_GPRS_RELEASE)
- Support of Immediate Connect (TSPC_AddInfo_ImmConn)
PIXIT Statements
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.5 Network Control measurement reporting / Dedicated connection / Handover / T3158 expiry | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.5.1 Conformance requirement | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.5.1.1 Conformance requirement for R97 and R98 MS | The behaviour of the mobile station is controlled by the parameter NETWORK_CONTROL_ORDER broadcast in the PSI5 message on PBCCH, in the SI13 message on the BCCH and in the PSI13 message on PACCH. Alternatively, the network may send the NETWORK_CONTROL_ORDER parameters in a PACKET MEASUREMENT ORDER or in a PACKET CELL C... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.5.1.2 Conformance requirement for R99 and later MS | A set of measurement reporting parameters (NETWORK_CONTROL_ORDER and NC_REPORTING_PERIOD(s)) is broadcast on PBCCH. The parameters may also be sent individually to an MS on PCCCH or PACCH, in which case it overrides the broadcast parameters. The individual parameters are valid until the RESET command is sent to the MS ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.5.2 Test Purpose | To verify that some R97 MS involved in NC measurement reporting, and making a handover during a dedicated connection do not send any buffered PACKET MEASUREMENT REPORT when many reporting periods had expired during a CS call on the first cell. They shall restart their measurement reporting on the new serving cell only ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.5.3 Method of test | Initial conditions
System Simulator:
1 cell (Cell A), GPRS supported, NC2, Ready Timer set to 5 minutes
1 cell (Cell B), GPRS supported, NC0, Ready Timer set to 5 minutes
Mobile Station:
The MS is in packet idle mode, with a TMSI, P-TMSI allocated
Specific PICS Statements
- Release of GPRS Supported (TSPC_MS_GPRS_RELEA... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.6 Network Control measurement reporting / Dedicated connection / Assignment Reject/ | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.6.1 Conformance requirement | When in mode NC1 or NC2, the mobile station shall perform the NC measurements as defined in 3GPP TS 05.08. The reporting periods are indicated in the NC_REPORTING_PERIOD_I and NC_REPORTING_PERIOD_T field of the PSI5, the SI2quater, the PACKET CELL CHANGE ORDER or the PACKET MEASUREMENT ORDER message. If NC_NON_DRX_PERI... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.6.2 Test Purpose | To verify that if a MS involved in NC measurement reporting is paged for CS connection but receives an IMMEDIATE ASSIGNMENT REJECT to its CHANNEL REQUEST sent in response to the paging, the MS continues its NC measurement reporting. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.3.6.3 Method of test | Initial conditions
System Simulator:
1 cell, GPRS supported, NC0, Ready Timer set to 5 minutes
Mobile Station:
The MS is in packet idle mode, with a TMSI, P-TMSI allocated
Specific PICS Statements
-
PIXIT Statements
-
Foreseen final state of the MS
- MS is in packet idle mode
Test procedure
MS is in packet idle mode, o... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.4 Network Control measurement reporting / NC_FREQUENCY_LIST | 42.4.8.4.1 Network Control measurement reporting / NC_FREQUENCY_LIST / NC_FREQUENCY_LIST in Packet measurement order. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.4.1.1 Conformance requirement | The GSM Neighbour Cell list may be modified by "NC Frequency List" in a PACKET CELL CHANGE ORDER message (in which case the reference list is given on the new cell) or one or more instances of the PACKET MEASUREMENT ORDER message with the same BA_IND value or PSI3_CHANGE_MARK value.
The "NC Frequency List" may add cell... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.4.1.2 Test Purpose | To verify that if the NC_FREQUENCY_LIST is included in the PACKET MEASUREMENT ORDER, MS updates the neighbour cell list and uses the updated list for the measurement reporting and reselection. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.4.1.3 Method of test | Initial conditions
System Simulator:
3 cells, GPRS supported.
Cell A (in case of GSM900 only): BS_PA_MFRMS = 2 (4 multi frames)
Initial conditions
Parameter
Cell A
Cell B
Cell C
Carrier 1
Carrier 2
Carrier 3
Channel Type Carried
BCCH
BCCH
BCCH
RF Signal Level (dBm)
-60
-75
-75
Serving Cell Parameters
NETWORK_CONTROL_OR... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.4.2 Void | 42.4.8.4.3 Network Control measurement reporting / NC_FREQUENCY_LIST / PMO with empty NC_FREQUENCY_LIST/ Return to BA(GPRS). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.4.3.1 Conformance requirement | The “NC Frequency List” may add cells to the GSM Neighbour Cell list (see sub-clause 11.2.4 and 11.2.9b, “PACKET CELL CHANGE ORDER” and “PACKET MEASUREMENT ORDER”). These cells shall be added at the end of the GSM Neighbour Cell list and indexed in the order of occurrence within the PACKET CELL CHANGE ORDER message or ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.4.3.2 Test Purpose | To verify that MS involved in measurement reporting reverts to BA(GPRS) on reception of PMO with empty NC_FREQUENCY_LIST list. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.4.3.3 Method of test | Initial Conditions
System Simulator:
- 3 cells. Cell B is part of BA(GPRS) of Cell A. Cell C is not a part of the BA(GPRS) of Cell A. None of the cells support PBCCH.
Cell A (in case of GSM900 only): BS_PA_MFRMS = 2 (4 multi frames)
Mobile Station:
- The MS is in GPRS attached with a P-TMSI allocated on Cell A, Ready ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.4.4.1 Conformance requirement | A parameter NC_FREQUENCY_LIST may also be sent individually to an MS on PCCCH or PACCH. This list adds/deletes frequencies to the BA(GPRS) both for cell re-selection and for measurement reports. For added frequencies, the corresponding cell re-selection parameters may be included. The list is valid until an empty list ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.4.4.2 Test Purpose | To verify that MS returns to BA(GPRS) if BA(GPRS) on which the NC_FREQ_LIST is built, is changed. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.4.4.3 Method of test | Initial Conditions
System Simulator:
3 cells, default settings. Cell C is removed from the BA(GPRS) on cell A.
Mobile Station:
The MS is in GPRS attached with a P-TMSI allocated on Cell A. READY TIMER is set to 5 min.
Specific PICS Statements
-
PIXIT Statements
-
Test Procedure
SS sends a PACKET MEASUREMENT ORDER messa... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.4.5 Network Control measurement reporting / NC_FREQUENCY_LIST / Dedicated connection/ Return to BA(GPRS) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.4.5.1 Conformance requirement | The procedure for measurement report sending shall be initiated by the mobile station at expiry of either the NC measurement report interval timer T3158 or the EM measurement report interval timer T3178. At expiry of the timer T3158 or T3178 the mobile station shall restart the expired timer T3158 or T3178, perform the... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.4.5.2 Test Purpose | To verify that MS involved in measurement reporting successfully returns to BA(GPRS) broadcast on BCCH after a dedicated connection. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.4.5.3 Method of test | Initial Conditions
System Simulator:
- 3 cells, default settings. Cell C is removed from the BA(GPRS) on both cell A and cell B.
- Ready Timer Deactivated on all cells.
Mobile Station:
The MS is in GPRS attached with a TMSI and a P-TMSI allocated.
Specific PICS Statements
- Support of Immediate Connect (TSPC_AddInfo_Im... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.4.6.1 Conformance requirement | If the mobile station receives a PACKET MEASUREMENT ORDER message (full set of instances) with changed PMO_IND parameter value, any old "NC frequency list" shall be deleted. If the last PACKET MEASUREMENT ORDER message (full set of instances) does not contain a "NC frequency list" (no added or deleted frequencies) the ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.4.6.2 Test Purpose | To verify that when instances of PACKET MEASUREMENT ORDER is sent including NC_FREQUENCY_LIST MS has to construct this frequency list and include the cells in the PACKET MEASUREMENT REPORTS. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.4.6.3 Method of test | Initial conditions
System Simulator:
3 cells default settings.,
Cell A in NC2. Cell C is removed from the BA(GPRS) of cell A.
Mobile Station:
MS is in Packet Idle mode and GPRS attached on Cell A.
PDP context 2 established.
Specific PICS Statements
-
PIXIT Statements
-
Foreseen final state of the MS
• MS is in transfer... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.4.7.1 Conformance requirement | The "NC Frequency List" may add cells to the GSM Neighbour Cell list . These cells shall be added at the end of the GSM Neighbour Cell list and indexed in the order of occurrence within the PACKET CELL CHANGE ORDER message or ascending instances of the PACKET MEASUREMENT ORDER message. The list of added cells may conta... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.4.7.2 Test Purpose | To verify that if a same cell (ARFCN+BSIC) occurs more than once in the Neighbour cell list; MS reports the cell with the highest index. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.4.7.3 Method of test | Initial conditions:
System Simulator:
2 cells, GPRS supported.
Mobile Station:
The MS is GPRS attached, in Packet Idle Mode.
Specific PICS Statements
-
PIXIT Statements
-
Test procedure
SS sends a PACKET MEASUREMENT ORDER message (including the NC_FREQUENCY_LIST) Changing the NC mode to NC2, adding the cell B to the Ne... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.5 NC2 and DTM | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.5.1 Ignoring Packet Measurement Order and Packet Cell Change Order whilst in DTM | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.5.1.1 Conformance requirements | An MS in network control mode NC1 or NC2 may enter an exceptional case if a circuit switched connection is established, which takes precedence over GPRS cell re-selection. This includes an MS operating in DTM.
References
3GPP TS 45.008, sub-clause 10.1.4.3 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.5.1.2 Test purpose | To verify that the MS operating in DTM ignores Packet Measurement Order and Packet Cell Change Order. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.4.8.5.1.3 Method of test | Initial Conditions
System Simulator:
2 cells with default parameter: A, B with same LAI, both supporting GPRS DTM
Mobile Station:
The MS is in the active state (U10) of a call on Timeslot N (chosen arbitrarily) of cell A and has the PDP context 1 activated.
Specific PICS Statements
-
PIXIT Statements
-
Test Procedure
T... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.5 Downlink Transfer | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.5.1 Downlink Transfer / Normal Operation | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.5.1.1 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.5.1.2 Downlink Transfer/ Normal Operation / Without TBF starting time | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.5.1.2.1 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.5.1.2.2 Conformance Requirement | 1. On receipt of a PACKET DOWNLINK ASSIGNMENT message, the mobile station shall switch to the assigned PDCHs.
2. The Packet downlink assignment procedure is completed when the mobile station receives a valid RLC/MAC block. The mobile station has entered the packet transfer mode.
3. If the MS is required to transmit a P... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.5.1.2.3 Test purpose | Verify that an MS switches to the assigned PDCH when assigned to it without a starting time, within 3 blocks. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.5.1.2.4 Method of test | Initial Conditions
System Simulator:
1 cell, GPRS supported, CTRL_ACK_TYPE=0 in GPRS cell options.
Mobile Station:
The MS is in the state "idle, GMM-registered" with a P-TMSI allocated, SPLIT PG CYCLE negotiated, and PDP context 3 activated.
Specific PICS Statements
-
PIXIT Statements
-
Test Procedure
1. MS receives a ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.5.2 Downlink Transfer / Polling | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.5.2.1 Downlink Transfer/ Polling/ Normal operation/RLC data block | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.5.2.1.1 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 42.5.2.1.2 Conformance Requirement | Whenever the mobile station receives an RLC data block addressed to itself and with a valid RRBP field in the RLC data block header (i.e., is polled), the mobile station shall transmit a Packet Downlink ACK/NACK message in the uplink radio block specified by the RRBP field whatever the BSN value of the received RLC dat... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.