hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.2.4.37 System Information Type 6 | L2 pseudo length
This is the sum of the lengths of all the information elements present in the message except for the SI 6 rest octets and L2 pseudo length IEs. For the default message the L2 pseudo length is 11.
RR management Protocol
Discriminator
0110 (radio resources management messages)
Skip Indicator
0000
System ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.2.4.38 DTM Information | RR management Protocol Discriminator
0110 (radio resources management messages)
Skip Indicator
0000
DTM Information Message Type
01001101
Routeing Area Identification
Same as the BCCH
DTM Information Rest Octets
- < LENGTH_IN_OCTETS : bit(8) >
00000011
- < MAX_LAPDm : bit (3) >
000 (Any message segmented in up to 5 LAP... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.2.4.39 PS Handover | PAGE_MODE
default
Global TFI
TFI of mobile station uplink TBF
CONTAINER_ID
00 PS Handover to A/Gb Mode Payload
PS Handover RR Info flag
00 PS Handover RR Info
PS Handover Radio Resources IE
present
Handover Reference
0
ARFCN
default ARFCN for BCCH of cell B
SI
01 Synchronized
NCI
0
BSIC
BSIC of cell B
0 <CCN_ACTIVE>
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.3 Default GPRS Conditions and Message Contents for the Higher Layer Test Cases | This clause details default conditions and messages that shall be used for the higher layer test cases (GPRS Mobility Management, Session Management and SNDCP).
These alternate conditions and messages are derived from the standard defaults via the changes listed in the following sub-clause. They aim to produce default ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.3.1 Default Test Conditions for the Higher Layer Test Cases | Network dependant parameters
CCCH_CONF
1 basic physical channel for CCCH combined with SDCCH
BS_AG_BLKS_RES
0 blocks reserved
BS_PA_MFRMS
5 multiframes
IMSI Attach-detach
IMSI attach / detach not allowed |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.3.2 Default Message for the Higher Layer Test Cases | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.3.2.1 Default Contents of System Information Messages for the Higher Layer Test Cases | Default Contents of Information Elements in SYSTEM INFORMATION TYPE 1 to 13 Messages Used for the Higher Layer Test Cases.
Control Channel Description
- BS_AG_BLKS_RES
0 blocks reserved for access grant.
- CCCH_CONF
1 basic physical channel used for CCCH, combined with SDCCHs.
- BS_PA_MFRMS
5 multiframe periods for tra... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.3.3 Contents Of Packet System Information Messages for the Higher Layer Test Cases | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.3.4 Contents of Layer 2 Messages for the Higher Layer Test Cases | PACKET UPLINK ASSIGNMENT message:
{0|1<Frequency Parameters>}
1 (Frequency Parameters present)
- Frequency Parameters
- ARFCN
ARFCN of the CCCH
Single Block Allocation
01 (Single Block Allocation)
- TIMESLOT_NUMBER
010
1 (ALPHA, GAMMA_TN present)
PACKET DOWNLINK ASSIGNMENT message:
{0|1<Frequency Parameters>}
1 (Freque... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.3.5 Contents of Layer 3 Messages for the Higher Layer Test Cases | IMMEDIATE ASSIGNMENT message:
Packet Channel Description
- TN
2 (Chosen arbitrarily)
- ARFCN
ARFCN of the CCCH
IMMEDIATE ASSIGNMENT EXTENDED message:
Channel Description 1
- Channel Type and TDMA offset
SDCCH/4, with subchannel chosen arbitrarily by the test house.
- Timeslot Number
0
- ARFCN
ARFCN of the CCCCH |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.3.6 Timer tolerance for higher layer test cases | The timers specified in the test cases in section 44, 45 and 46 shall take into account the delay in the establishment of uplink and/or downlink TBF required as per the test sequence. Timer tolerance = Timer Value +/- 10% +/- Delay to establish TBF. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4 Macros | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.1 Overview | The present document presents macros for GPRS test cases. It is intended to be a working document forming part of the GPRS Test Specifications. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.1.1 Definition | A macro is a name or sentence, possibly followed by an argument list, that is equated to a text to which it is to be expanded, possibly with the substitution of actual arguments.
Macros may be used to simplify the writing and reading of the test cases or to avoid the repetition of common sentences, message contents or ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.1.2 Syntax | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.1.2.1 Message contents | Any macro referencing message contents shall use the following table:
Macro reference (arguments)
SI
Information Element
Value/Remarks
The table must contain:
Macro reference: word or sentence that gives the name to the macro. It may include a list of arguments with actual values for some IE's.
SI: the System Informati... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.1.2.2 Message sequence | Any macro referencing message contents shall use the following table:
Step
Direction
Message
Comments
{ Macro reference }
Macro (arguments)
The table must contain:
Macro reference: word or sentence that gives the name to the macro. It may include a list of arguments with actual values for some parameters used within th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.2 Default message contents | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.2.1 GPRS not supported | SI
Information Element
Value/Remarks
SI 3
SI 4
SI 7
SI 8
GPRS Indicator
GPRS not supported |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.2.2 GPRS supported | SI
Information Element
Value/Remarks
SI 3
SI 4
SI 7
SI 8
GPRS Indicator
GPRS supported |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.2.3 GPRS supported using BCCH | (P)SI
Information Element
Value/Remarks
SI 13
[Bit after RA_CODE]
PCCCH not present |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.2.4 Max retrans set to {1, 2, 4, 7} | (P)SI
Information Element
Value/Remarks
SI 1
SI 2
SI 2bis
SI 3
SI 9
RACH Control Parameters
- Max retrans
Maximum 1 retransmission,
maximum 2 retransmissions,
maximum 4 retransmissions or
maximum 7 retransmissions |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.3 Macro message sequences | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.3.1 Acknowledged downlink data | Step
Direction
Message
Comments
SS MS
{ Acknowledged downlink data }
Macro
1
SS MS
{ Downlink data }
Macro
2
MS SS
PACKET DOWNLINK ACK/NACK |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.3.2 Classmark and measurement | Step
Direction
Message
Comments
MS SS
{ Classmark and measurement }
Macro
1a
MS SS
MEASUREMENT REPORT
2a
MS SS
CLASSMARK CHANGE
Mobile Station Classmark 2 and 3
1b
MS SS
CLASSMARK CHANGE
Mobile Station Classmark 2 and 3
2b
MS SS
MEASUREMENT REPORT
3
MS SS
{ Measurement reporting }
Macro |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.3.3 Downlink data | Step
Direction
Message
Comments
SS MS
{ Downlink data }
Macro
1
SS MS
RLC DOWNLINK DATA
FBI bit set to '0'
2
SS MS
RLC DOWNLINK DATA
N
SS MS
RLC DOWNLINK DATA
n 1 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.3.4 Downlink data transfer | Step
Direction
Message
Comments
SS MS
{ Downlink data transfer }
Macro
a. RLC unacknowledged mode
1
SS MS
{ Downlink data }
Macro
2
SS MS
RLC DOWNLINK DATA
FBI bit set to '1' and valid RRBP field
3
MS SS
PACKET CONTROL ACKNOWLEDGMENT
In the uplink block specified by the RRBP field
b. RLC acknowledged mode
1
SS ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.3.5 Measurement reporting | Step
Direction
Message
Comments
MS SS
{ Measurement reporting }
Macro
1
MS SS
MEASUREMENT REPORT
See note
2
MS SS
MEASUREMENT REPORT
N
MS SS
MEASUREMENT REPORT
n 1
NOTE: These messages are sent continuously on the ACCH. As no short messages are sent, this sequence should not be temporarily interrupted b... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.3.6 Uplink data transfer | Step
Direction
Message
Comments
MS SS
{ Uplink data transfer }
Macro (arguments: see note 4)
1
MS SS
RLC UPLINK DATA
See notes 1 and 2
2a
MS SS
RLC UPLINK DATA
2b
SS MS
PACKET UPLINK ACK/NACK
See note 3
3a
MS SS
RLC UPLINK DATA
3b
SS MS
PACKET UPLINK ACK/NACK
N
MS SS
RLC UPLINK DATA
n 1. CV set to... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.3.7 Uplink dynamic allocation one phase access | Step
Direction
Message
Comments
{Uplink dynamic allocation one phase access}
Macro parameters:
n: the number of RLC data block to be transferred,
USF_GRANULARITY: 1 or 4 blocks,
RLC_DATA_BLOCKS_GRANTED: 9-261 (close-end), or absent (open-end)
CHANNEL_CODING_COMMAND: CS-1, -2, -3, -4
TLLI_BLOCK_CHANNEL_CODING: CS-1 or a... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.3.8 Uplink dynamic allocation one phase access with contention resolution | Step
Direction
Message
Comments
{Uplink dynamic allocation one phase access with contention resolution}
Macro parameters:
n: the number of RLC data block to be transferred,
USF_GRANULARITY: 1 or 4 blocks,
RLC_DATA_BLOCKS_GRANTED: 9-261 (close-end), or absent (open-end)
CHANNEL_CODING_COMMAND: CS-1, -2, -3, -4
TLLI_BLOC... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.3.9 Uplink dynamic allocation two phase access | Step
Direction
Message
Comments
{Uplink dynamic allocation two phase access}
Macro parameters:
n: the number of RLC data block to be transferred,
USF_GRANULARITY: 1 or 4 blocks,
RLC_DATA_BLOCKS_GRANTED: 9-261 (close-end), or absent (open-end)
CHANNEL_CODING_COMMAND: CS-1, -2, -3, -4
TLLI_BLOCK_CHANNEL_CODING: CS-1 or a... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.3.10 Completion of uplink RLC data block transfer | Steps 1A - 3A are applied for 1 uplink slot with USF granularity 1 block.
Steps 1B, 2B1-2B4 and 3B are applied for 1 uplink slot with USF granularity 4 blocks.
Steps 1C - 5C are applied for 2 uplink slots with USF granularity 1 block.
Steps 6 - 7 are common to the cases A, B and C.
Step
Direction
Message
Comments
{Comp... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.3.10.1 PACKET UPLINK ACK/NACK message in step 6: | Ack/Nack Description
- FINAL_ACK_INDICATION
1 (final ACK)
- STARTING_SEQUENCE_NUMBER
No information, ignored
- RECEIVED_BLOCK_BITMAP
No information, ignored |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.3.11 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.3.12 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.3.13 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.3.14 Downlink TBF establishment | Step
Direction
Message
Comments
{Downlink TBF establishment}
Macro parameters:
RLC mode
TBF_STARTING_TIME
1
SS -> MS
PAGING REQUEST
1st Repeated Page info contains P-TMSI of the MS. Sent on PCH.
2
MS -> SS
CHANNEL REQUEST
ACCESS TYPE = " Page Response ". Received on RACH.
3
SS -> MS
IMMEDIATE ASSIGNMENT
Random Referenc... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.3.15 PDP Context Activation | Mobile initiated, for LLC mode unacknowledged:
Step
Direction
Message
Comments
{PDP Context Activation}
1
MS -> SS
Activate PDP Context Request
2
SS -> MS
Activate PDP Context Accept
Mobile initiated, for LLC mode acknowledged:
Step
Direction
Message
Comments
{PDP Context Activation}
1
MS -> SS
Activate PDP Context Req... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.3.16 PDP Context Deactivation | Mobile initiated:
Step
Direction
Message
Comments
{PDP Context Deactivation}
1
MS -> SS
Deactivate PDP Context Request
2
SS -> MS
Deactivate PDP Context Accept
Network initiated:
Step
Direction
Message
Comments
{PDP Context Deactivation}
1
SS -> MS
Deactivate PDP Context Request
2
MS -> SS
Deactivate PDP Context Accept |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.3.17 Inter-SGSN Routing Area Update | Step
Direction
Message
Comments
{Inter-SGSN Routing Area Update}
1
Cell B is already activated with a lower signal strength than cell A The RF level of cell A is lowered until cell B is preferred by the MS.
2
MS -> SS
Routing Area Update Request
The updating type shall be "Combined RA/LA Updating" for Class B mobiles i... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.3.18 PDP Context Modification | This procedure is always initiated by the network.
Step
Direction
Message
Comments
{PDP Context Modification}
1
SS -> MS
Modify PDP Context
2
MS -> SS
Modify PDP Context Accept |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.3.19 Location Update Procedure | This procedure is only initiated by mobile stations that are not operating in class mode C "GPRS".
Step
Direction
Message
Comments
{Location Update Procedure}
Macro parameters:
MOBILE_IDENTITY
1
MS -> SS
LOCATION UPDATE REQUEST
2
SS -> MS
AUTHENTICATION REQUEST
3
MS -> SS
AUTHENTICATION RESPONSE
4
SS -> MS
LOCATION UPD... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.3.20 MT Call in GPRS cell | This procedure is initiated by the network while the MS is GPRS attached, one cell is active:
Step
Direction
Message
Comments
{MT Call while GPRS Attached}
Macro parameters:
T : Duration of the call (in seconds)
R : Binary acknowledge of a successful resumption of GPRS services
1
SS -> MS
PAGING REQUEST Type 1
Page inf... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.3.21 Uplink data | Step
Direction
Message
Comments
MS SS
{ Uplink data }
Macro (arguments: see note 2)
1
MS SS
RLC UPLINK DATA
SI bit set to ‘0’
2a
MS SS
RLC UPLINK DATA
See notes 1
2b
SS MS
PACKET UPLINK ACK/NACK
N
MS SS
RLC UPLINK DATA
till the required amount of blocks are received
N+1
SS MS
PACKET UPLINK ACK/N... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.3.22 Bring MS in the active state (U10) | Step
Direction
Message
Comments
{Bring MS in active state (U10)}
Macro parameters:
N : Timeslot used for traffic channel
1
SS -> MS
PAGING REQUEST Type 1
Page info contains IMSI of the MS, sent on downlink PCH
2
MS -> SS
CHANNEL REQUEST
Establishment cause : ANSWER TO PAGING
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
P... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.3.23 Completion of uplink RLC data block transfer in extended dynamic mode | Step
Direction
Message
Comments
{Completion of uplink RLC data block transfer in extended dynamic mode}
Macro parameters:
USF_GRANULARITY: 1 or 4 blocks,
the number of timeslots assigned in the uplink,
the lowest numbered timeslot in the PDCH allocation.
USF1 is assigned on TN1 (the lowest numbered timeslot), USF2 is a... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.4.3.23.1 PACKET UPLINK ACK/NACK message in step 4: | Ack/Nack Description
- FINAL_ACK_INDICATION
1 (final ACK)
- STARTING_SEQUENCE_NUMBER
No information, ignored
- RECEIVED_BLOCK_BITMAP
No information, ignored |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 40.5 Test PDP contexts | The following table defines Test PDP contexts required for test cases using packet services (e.g. GPRS, EGPRS, DTM). Test PDP context3 is the default Test PDP context which is used in the test cases where no particular Test PDP contexts are specified. Compression is always turned off if nothing else is stated explicitl... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1 RR / Paging | The paging procedure is used by the network to cause the MS to establish either an RR connection for circuit switched services or a downlink GPRS packet transfer. Normally the MS listens to its paging sub-channel when DRX is used, but this can be modified by the use of different page mode. The correct monitoring of its... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.1 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.2 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.3 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.4 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.5 RR / Paging / on CCCH for GPRS service | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.5.1 RR / Paging / on CCCH for GPRS service / normal paging | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.5.1.1 RR / Paging / on CCCH for GPRS service / normal paging with P-TMSI successful | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.5.1.1.1 Conformance requirements | 1. The network initiates the paging procedure by sending a paging request message on an appropriate paging sub-channel on CCCH. Paging initiation using a paging sub-channel on CCCH is used when sending paging information to a mobile station and PCCCH is not present in the cell.
2. The mobile station in packet idle mode... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.5.1.1.2 Test purpose | 1. To verify that the MS in packet idle mode, GPRS attached state, is able to determine its CCCH group and PAGING group and that the MS responds correctly with CHANNEL REQUEST on RACH with cause value of 'packet access' upon receipt of a PAGING REQUEST TYPE 1 message for packet access with paging mode set to normal.
2.... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.5.1.1.3 Method of test | Initial Conditions
System Simulator:
1 cell, CCCH combined with SDCCH, GPRS supported, PCCCH absent, Max-Retrans = 2, BS_AG_BLKS_RES = 2, BS_PA_MFRMS = 6, SPLIT_PG_CYCLE is supported on CCCH in the cell.
Mobile Station:
The MS is GPRS attached with a TMSI (only for MS operation mode A or MS operation mode B) and a P-TM... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.5.1.2 RR / Paging / on CCCH for GPRS service / normal paging with IMSI successful | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.5.1.2.1 Conformance requirements | 1. If the MS was paged by the network with the IMSI (for GPRS service), the MS shall delete any RAI, P-TMSI, P-TMSI signature and GPRS ciphering key sequence number stored. The MS shall then perform a GPRS attach or combined GPRS attach procedure.
References
3GPPTS 04.08 / 3GPP TS 24.008, subclause 4.7.9.1.2. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.5.1.2.2 Test purpose | To verify that the MS is able to respond to PAGING REQUEST TYPE 1 when the MS is addressed with its IMSI with Packet Page Indication set to packet paging procedure, and that the MS then performs a GPRS attach or combined GPRS attach procedure. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.5.1.2.3 Method of test | Initial Conditions
System Simulator:
1 cell, CCCH combined with SDCCH, GPRS supported, PCCCH absent, Max-Retrans = 2, BS_AG_BLKS_RES = 2, BS_PA_MFRMS = 9.
Mobile Station:
The MS is in GPRS attached with a TMSI (only for MS operation mode A or MS operation mode B) and a P-TMSI allocated, SPLIT PG CYCLE negotiated. The m... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.5.1.3 RR / Paging / on CCCH for GPRS service / normal paging with P-TMSI ignored | The MS shall ignore paging not addressing to it. If paging is not implemented correctly unnecessary accesses will be provoked on CCCH which is shared by all MS in a same cell. This kind of the wrong paging behaviour of the same type of MS in a GSM network can block the use of CCCH and will, therefore, cause an unaccept... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.5.1.3.1 Conformance requirements | In a PAGING REQUEST message used for the packet paging procedure, the mobile station shall be identified by the TMSI (GPRS TMSI) or its IMSI. A PAGING REQUEST message may include more than one mobile station identification.
References
3GPP TS 04.08 / 3GPP TS 44.018, subclauses 3.3.2.1.1 and 3.5.1.1. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.5.1.3.2 Test purpose | To verify that the MS ignores a PAGING REQUEST TYPE 1, 2 messages where both P-TMSI and IMSI do not address the MS although the paging message is sent on the CCCH to which the CCCH_GROUP belongs. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.5.1.3.3 Method of test | Initial Conditions
System Simulator:
1 cell, CCCH combined with SDCCH, GPRS supported, PCCCH absent, Max-Retrans = 2, BS_AG_BLKS_RES = 2, BS_PA_MFRMS = 7, .
Mobile Station:
The MS is GPRS attached with a TMSI (only for MS operation mode A or MS operation mode B) and a P-TMSI allocated and SPLIT PG CYCLE negotiated. The... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.5.2 RR / Paging / on CCCH for GPRS service / extended paging | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.5.2.1 RR / Paging / on CCCH for GPRS service / extended paging with P-TMSI successful | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.5.2.1.1 Conformance requirements | The paging and immediate assignment type messages contain a page mode information element. This information element controls possible additional requirements on mobile stations belonging to the paging subgroup corresponding to the paging subchannel the message was sent on. This implies that a given mobile station shall... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.5.2.1.2 Test purpose | 1. To verify that the MS operates in the extended page mode when it is ordered by the SS in PAGING REQUEST TYPE 1 which does not address the MS, but on the paging sub-channel corresponding to the MS identity.
2. To verify that the MS operates in the extended page mode when it is ordered by the SS in PAGING REQUEST TYPE... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.5.2.1.3 Method of test | Initial Conditions
System Simulator:
1 cell, GPRS supported, PCCCH absent, Max-Retrans = 2, CCCH_CONF = 1 basic physical channel used for CCCH with non-combined SDCCH, BS_AG_BLKS_RES = 3, BS_PA_MFRMS = 8.
Mobile Station:
The MS is GPRS attached with a TMSI (only for MS operation mode A or MS operation mode B) and a P-T... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.5.3 RR / Paging / on CCCH for GPRS service / paging reorganisation | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.5.3.1 Conformance requirements | The paging and immediate assignment type messages contain a page mode information element. This information element controls possible additional requirements on mobile stations belonging to the paging subgroup corresponding to the paging subchannel the message was sent on. This implies that a given mobile station shall... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.5.3.2 Test purpose | 1. To verify that the MS, after reception of a message with page mode set to "paging reorganisation", answers to paging messages (with page mode set to "normal paging") sent on its old CCCH in paging blocks which do not belong to the MS's paging sub-channel.
2. To test that the MS correctly determines its new paging su... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.5.3.3 Method of test | Initial Conditions
System Simulator:
1 cell, GPRS supported, PCCCH absent, Max-Retrans = 2, CCCH_CONF = 0 (1 basic physical channel used for CCCH with non-combined SDCCH), BS_AG_BLKS_RES = 3, BS_PA_MFRMS = 6. SPGC_CCCH_SUP = 0 (SPLIT_PG_CYCLE is not supported on CCCH in the cell).
Mobile Station:
The MS is GPRS attac... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.5.4 RR / Paging / on CCCH for GPRS service / default message contents | Contents for SYSTEM INFORMATION and PACKET SYSTEM INFORMATION Messages:
System information Type 13
L2 Pseudo Length
0
RR management Protocol Discriminator
RR
Skip Indicator
0000
System Information Type 13 Message Type
00
SI 13 Rest Octets
-
H (SI 13 Rest Octets are not spare)
- BCCH_CHANGE_MARK
000
- SI_CHANGE_FIELD
0 ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.1.6 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.2 RR procedures on CCCH related to temporary block flow establishment | This clause presents tests for "RR procedures on CCCH related to temporary block flow establishment" which are specified in 3GPP TS 04.08 / 3GPP TS 44.018, subclause 3.5.
Default conditions
The SS default conditions simulate one cell with default settings as defined in the GPRS general defaults section, except:
- SI 13... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.2.1 Permission to access the network | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.2.1.1 Permission to access the network / priority classes | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.2.1.1.1 Conformance requirements | Access to the network is allowed:
- if packet access is allowed in the cell for the priority class associated with the packet transfer, as indicated by the PRIORITY_ACCESS_THR parameter broadcast in SI 13 message.
References
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.5.2.1.1. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.2.1.1.2 Test purpose | To verify that the MS accesses the network only if packet access is allowed in the cell for the priority class associated with the packet transfer. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.2.1.1.3 Method of test | Initial conditions
System Simulator:
Network Mode of Operation is set to NMO II.
Mobile Station:
For PRIORITY_ACCESS_THR >2 MS is GPRS attached, a PDP context has been established (with priority level as specified below).
For PRIORITY_ACCESS_THR <=2 MS is Idle Updated.
Specific PICS Statements
-
PIXIT Statements
-
Test... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.2.2 Initiation of the packet access procedure | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.2.2.1 Initiation of the packet access procedure / establishment causes | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.2.2.1.1 Conformance requirements | The CHANNEL REQUEST messages are sent on RACH and contain the parameters:
- an establishment cause which indicates packet access, and as applicable, a request for one phase packet access or single block packet access;
- a random reference which is drawn randomly from a uniform probability distribution for every new tra... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.2.2.1.2 Test purpose | To verify that the CHANNEL REQUEST message sent by the MS contains the correct establishment cause when initiating a packet access procedure. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.2.2.1.3 Method of test | Initial conditions
System Simulator:
1 cell, CCCH combined with SDCCH.
Mobile Station:
MS is switched off.
Specific PICS Statements
-
PIXIT Statements
-
Test procedure
The MS is triggered to initiate a GPRS attach procedure. The SS verifies that the MS attempts a one phase packet access.
APDP context for RLC unacknowle... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.2.2.2 Random references for single block packet access | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.2.2.2.1 Conformance requirements | The random reference in the CHANNEL REQUEST messages shall be randomly drawn from a uniform probability distribution for every new transmission.
References
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.5.2.1.2. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.2.2.2.2 Test purpose | To verify that the MS produces different Random References when accessing the network for single block access. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.2.2.2.3 Method of test | Initial conditions
System Simulator:
1 cell, CCCH combined with SDCCH, Parameter MAX_RETRANS is set to 4 retransmissions.
Mobile Station:
MS is GPRS attached, a PDP context in RLC unacknowledged mode has been established and the MS is in Packet Idle mode.
Specific PICS Statements
-
PIXIT Statements
-
Test procedure
The... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.2.2.3 Random references for one phase packet access | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.2.2.3.1 Conformance requirements | The random reference in the CHANNEL REQUEST messages shall be randomly drawn from a uniform probability distribution for every new transmission.
References
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.5.2.1.2. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.2.2.3.2 Test purpose | To verify that the MS produces different Random References when accessing the network for one phase access. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.2.2.3.3 Method of test | Initial conditions
System Simulator: default settings except:
- Parameter MAX_RETRANS is set to 4 retransmissions.
- T3302 = 1 minute, T3212 sent in SI3 is set to 6 minutes.
Mobile Station:
Note: MS may be brought into the required condition by causing it to be triggered to perform GPRS attach and the SS responding wi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.2.2.4 Initiation of the packet access procedure / timer T3146 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 41.2.2.4.1 Conformance requirements | Having sent the maximum number of CHANNEL REQUEST messages, the mobile station starts timer T3146. At expiry of timer T3146, the packet access procedure is aborted and a packet access failure is indicated to upper layers.
Reference
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.5.2.1.2. |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.