bkuster's picture
Publish combined_v0: four pinned datasets, 1975 episodes and 146240 frames
f9184eb verified
|
Raw History Blame Contribute Delete
10.4 kB
---
license: apache-2.0
task_categories:
- robotics
tags:
- lerobot
- oracle
- franka
configs:
- config_name: default
data_files: data/*/*.parquet
---
# Elementary Franka oracle demonstrations
**1,069 episodes / 32,070 frames / 98 instructions at 15 FPS.**
| Group | Instructions | Episodes per instruction | Episodes |
|---|---:|---:|---:|
| Original movements and stiffness variants | 48 | 15 | 720 |
| Standalone open/close gripper | 2 | 20 | 40 |
| Movements with the gripper closed | 48 | 6 or 7 | 309 |
The closed-gripper extension is partially collected: **309 of the planned 480 episodes**, with 171 remaining. Its task distribution is not exactly balanced. This snapshot is ready for training on the collected data; exact counts are below.
## Observation and action contract
LeRobot v3.0; Franka Research 3; RGB 640×480 under `observation.images.image`. `observation.state` has 31 floats: measured Cartesian pose (XYZ + rotation-6D), commanded pose (XYZ + rotation-6D), measured base-frame Cartesian velocity (6), measured tool-frame wrench (6), and episode elapsed seconds (1). Measured gripper width is not in the state.
`action` has 11 floats: six tool-frame motion channels, normalized gripper closure, three stiffness factors, and done. Despite their `cart_pos_*_tool_commanded_rel` names, translation channels are velocity-like commands in m/s, integrated at dt=1/15 s; angular channels are rad/s. Gripper 0=open, 1=closed. XY/Z stiffness factors map to 100–1500 N/m; rotation maps to 10–30 Nm/rad. Done is zero for these elementary tasks. Exact feature names/order are in `meta/info.json`.
## Recording behavior
Original movement instructions command open fingers. Closed-gripper variants start with a verified 60 mm open gap, prepared before recording. **Arm movement and asynchronous closure start together on the first recorded action** and continue for two seconds. Empty-jaw closing uses positional Move to zero; no object-contact grasp is required. Initial/final gaps are in `closed_gripper_setup.jsonl` and `closed_gripper_endpoints.jsonl`. Standalone open tasks start closed; standalone close tasks start open.
Movement speed is 0.03 m/s or 0.15 rad/s after the 1.5 oracle multiplier. Starts use uniform independent offsets ±5 cm XYZ, ±2° roll, no pitch offset, ±5° yaw around the saved reference. Cartesian resets take six seconds plus a 0.5-second settling wait. Resets and initial opening are not recorded. These are elementary demonstrations, not pickup episodes.
Stiffness settings changed during collection; older episodes retain their actual historical labels. Later recordings cap rotation at 25 Nm/rad and scale physical XY/Z gains by 0.9, respecting the 100 N/m minimum: ordinary gains 900 N/m, maximum 1350 N/m; low-rotation tasks can use 10 Nm/rad. Task text alone does not uniquely determine every historical gain. Applied stiffness factors are in each action, with batch arguments/manifests in `source_metadata/`.
## Validation and provenance
Every retained video frame was decoded; data indices, metadata shard references, video ranges, numeric finiteness, gripper endpoints, and dataset-reader boundaries were checked. No identical complete two-second video sequences were found in the final snapshot. Known camera-disconnection episodes were removed. See `publication_validation.json`, `camera_filter_manifest.json`, and the historical cleanup manifests.
Filtering IDs refer to the historical snapshot identified in each manifest; later valid appends may reuse those IDs. Historical manifests and the original recording request can show older counts or targets. `meta/info.json` and `publication_validation.json` describe the published snapshot. Backups, rejected recordings, caches, credentials and model weights are excluded.
Structural validation and endpoint checks are not independent physical-success annotations, and do not rule out every transient stale camera frame. Camera reads use the latest cached image without blocking. Joint/nullspace motion is not fully represented by the Cartesian state.
## Training
Dataset ID: `bkuster/oracle_basic_15pertask_20261109_094952`. Use the 31-state/11-action contract and RGB key above. Metadata currently puts all episodes in `train`; make any validation split by episode rather than individual frames. `meta/stats.json` covers all retained data, so recompute training-only normalization after splitting or merging. Pin the publication commit for reproducibility.
## Exact task counts
| Task instruction | Episodes |
|---|---:|
| Move in gripper positive x | 15 |
| Move in gripper negative x | 15 |
| Move in gripper positive y | 15 |
| Move in gripper negative y | 15 |
| Move in gripper positive z | 15 |
| Move in gripper negative z | 15 |
| Rotate around gripper positive x | 15 |
| Rotate around gripper negative x | 15 |
| Rotate around gripper positive y | 15 |
| Rotate around gripper negative y | 15 |
| Rotate around gripper positive z | 15 |
| Rotate around gripper negative z | 15 |
| Move in base positive x | 15 |
| Move in base negative x | 15 |
| Move in base positive y | 15 |
| Move in base negative y | 15 |
| Move in base positive z | 15 |
| Move in base negative z | 15 |
| Rotate around base positive x | 15 |
| Rotate around base negative x | 15 |
| Rotate around base positive y | 15 |
| Rotate around base negative y | 15 |
| Rotate around base positive z | 15 |
| Rotate around base negative z | 15 |
| Open gripper | 20 |
| Close gripper | 20 |
| Move in base positive x with low XY stiffness | 15 |
| Move in base positive x with maximum stiffness | 15 |
| Move in base negative x with low XY stiffness | 15 |
| Move in base negative x with maximum stiffness | 15 |
| Move in base positive y with low XY stiffness | 15 |
| Move in base positive y with maximum stiffness | 15 |
| Move in base negative y with low XY stiffness | 15 |
| Move in base negative y with maximum stiffness | 15 |
| Move in base positive z with low Z stiffness | 15 |
| Move in base positive z with maximum stiffness | 15 |
| Move in base negative z with low Z stiffness | 15 |
| Move in base negative z with maximum stiffness | 15 |
| Rotate around base positive x with low rotational stiffness | 15 |
| Rotate around base positive x with maximum stiffness | 15 |
| Rotate around base negative x with low rotational stiffness | 15 |
| Rotate around base negative x with maximum stiffness | 15 |
| Rotate around base positive y with low rotational stiffness | 15 |
| Rotate around base positive y with maximum stiffness | 15 |
| Rotate around base negative y with low rotational stiffness | 15 |
| Rotate around base negative y with maximum stiffness | 15 |
| Rotate around base positive z with low rotational stiffness | 15 |
| Rotate around base positive z with maximum stiffness | 15 |
| Rotate around base negative z with low rotational stiffness | 15 |
| Rotate around base negative z with maximum stiffness | 15 |
| Move in gripper positive x with the gripper closed | 7 |
| Move in gripper negative x with the gripper closed | 7 |
| Move in gripper positive y with the gripper closed | 7 |
| Move in gripper negative y with the gripper closed | 7 |
| Move in gripper positive z with the gripper closed | 7 |
| Move in gripper negative z with the gripper closed | 7 |
| Rotate around gripper positive x with the gripper closed | 7 |
| Rotate around gripper negative x with the gripper closed | 7 |
| Rotate around gripper positive y with the gripper closed | 7 |
| Rotate around gripper negative y with the gripper closed | 7 |
| Rotate around gripper positive z with the gripper closed | 7 |
| Rotate around gripper negative z with the gripper closed | 7 |
| Move in base positive x with the gripper closed | 7 |
| Move in base negative x with the gripper closed | 7 |
| Move in base positive y with the gripper closed | 7 |
| Move in base negative y with the gripper closed | 7 |
| Move in base positive z with the gripper closed | 7 |
| Move in base negative z with the gripper closed | 7 |
| Rotate around base positive x with the gripper closed | 7 |
| Rotate around base negative x with the gripper closed | 7 |
| Rotate around base positive y with the gripper closed | 7 |
| Rotate around base negative y with the gripper closed | 6 |
| Rotate around base positive z with the gripper closed | 6 |
| Rotate around base negative z with the gripper closed | 6 |
| Move in base positive x with low XY stiffness with the gripper closed | 6 |
| Move in base positive x with maximum stiffness with the gripper closed | 6 |
| Move in base negative x with low XY stiffness with the gripper closed | 6 |
| Move in base negative x with maximum stiffness with the gripper closed | 6 |
| Move in base positive y with low XY stiffness with the gripper closed | 6 |
| Move in base positive y with maximum stiffness with the gripper closed | 6 |
| Move in base negative y with low XY stiffness with the gripper closed | 6 |
| Move in base negative y with maximum stiffness with the gripper closed | 6 |
| Move in base positive z with low Z stiffness with the gripper closed | 6 |
| Move in base positive z with maximum stiffness with the gripper closed | 6 |
| Move in base negative z with low Z stiffness with the gripper closed | 6 |
| Move in base negative z with maximum stiffness with the gripper closed | 6 |
| Rotate around base positive x with low rotational stiffness with the gripper closed | 6 |
| Rotate around base positive x with maximum stiffness with the gripper closed | 6 |
| Rotate around base negative x with low rotational stiffness with the gripper closed | 6 |
| Rotate around base negative x with maximum stiffness with the gripper closed | 6 |
| Rotate around base positive y with low rotational stiffness with the gripper closed | 6 |
| Rotate around base positive y with maximum stiffness with the gripper closed | 6 |
| Rotate around base negative y with low rotational stiffness with the gripper closed | 6 |
| Rotate around base negative y with maximum stiffness with the gripper closed | 6 |
| Rotate around base positive z with low rotational stiffness with the gripper closed | 6 |
| Rotate around base positive z with maximum stiffness with the gripper closed | 6 |
| Rotate around base negative z with low rotational stiffness with the gripper closed | 6 |
| Rotate around base negative z with maximum stiffness with the gripper closed | 6 |